The function brcms_set_hint() does not add any functionality
so regulatory_hint() can be called directly. The error value
has been removed from the message when regulatory_hint() fails.
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org [3.0+]
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stop connection monitor poll during disassociation.
This clears the polling flags and if a scan was
deferred it will be run.
Without this fix, if a scan was deferred due to
connection monitoring while disassociation happens,
this scan blocks further scan requests until interface
down/up which causes problems connecting to another AP.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise, we might call the driver callback before
the interface was uploaded.
Solves the following warning:
WARNING: at net/mac80211/driver-ops.h:12 ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]()
wlan0: Failed check-sdata-in-driver check, flags: 0x0
Modules linked in: wlcore_sdio wl12xx wl18xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[<c001b964>] (unwind_backtrace+0x0/0x12c) from [<c0495550>] (dump_stack+0x20/0x24)
[<c0495550>] (dump_stack+0x20/0x24) from [<c003ee28>] (warn_slowpath_common+0x5c/0x74)
[<c003ee28>] (warn_slowpath_common+0x5c/0x74) from [<c003eefc>] (warn_slowpath_fmt+0x40/0x48)
[<c003eefc>] (warn_slowpath_fmt+0x40/0x48) from [<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211])
[<bf5c1ad0>] (ieee80211_set_bitrate_mask+0xbc/0x18c [mac80211]) from [<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211])
[<bf575960>] (nl80211_set_tx_bitrate_mask+0x350/0x358 [cfg80211]) from [<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8)
[<c03e9e94>] (genl_rcv_msg+0x1a8/0x1e8) from [<c03e9164>] (netlink_rcv_skb+0x5c/0xc0)
[<c03e9164>] (netlink_rcv_skb+0x5c/0xc0) from [<c03e9ce0>] (genl_rcv+0x28/0x34)
[<c03e9ce0>] (genl_rcv+0x28/0x34) from [<c03e8e74>] (netlink_unicast+0x158/0x234)
[<c03e8e74>] (netlink_unicast+0x158/0x234) from [<c03e93e0>] (netlink_sendmsg+0x218/0x298)
[<c03e93e0>] (netlink_sendmsg+0x218/0x298) from [<c03b4e5c>] (sock_sendmsg+0xa4/0xc0)
[<c03b4e5c>] (sock_sendmsg+0xa4/0xc0) from [<c03b5af4>] (__sys_sendmsg+0x1d8/0x254)
[<c03b5af4>] (__sys_sendmsg+0x1d8/0x254) from [<c03b5ca8>] (sys_sendmsg+0x4c/0x70)
[<c03b5ca8>] (sys_sendmsg+0x4c/0x70) from [<c0013980>] (ret_fast_syscall+0x0/0x3c)
Note that calling the driver can also result
in undefined behaviour since it doesn't have
to deal with calls while down.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[removed timestamps, added note - Johannes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This flow can actually happen due to a corner case in
mac80211: the station is deleted before we get a chance
to reclaim all the packets in flight in AGG queue.
The tid_data for this station is zeroed, and we lose
the match with the Tx queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since request_module_nowait() can't be backported
use request_module() instead -- we don't need the
asynchronous behaviour of request_module_nowait()
here since we're running in the firmware request
work struct.
Tested-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to commit 26a7ca9a71 ("iwlwifi: refactor EEPROM
reading/parsing") adding a new parameter, while commit
d2c8b15d0c ("iwlwifi: use correct supported firmware
for 6035 and 6000g2") added a new device structure we
need to add the parameter to the new device structure
to make 6035 device work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For AGG queues, we must match between the WiFi sequence
number and the TFD number. This is a HW (SCD) requirement.
This is a take two of my
iwlwifi: add debug in Tx path in AGG flow
This will allow us to catch bad cases in which the packets aren't in
the right place on the ring.
which disappeared during code move.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In fragmentation we don't update the write pointer of the
HW immediately. So we shouldn't modify the timer in that
case.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CMD_SYNC is zero so the if (cmd->flags & CMD_SYNC) is never true and we
never check the assertion.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the queue gets stuck from time to time, we are trying
to get as much information as we can when this occurs.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver is built into the kernel instead of a module
when the system boots it results in a panic. The order things are built in
results in their initialization order when built into the kernel. Wifi
has to be initialized before mvm or dvm.
Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Tested-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Brandon Misemer <brandon.misemer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using the driver_data area in ieee80211_tx_info which
resides in the CB overrides the info->control field.
Add a comment to prevent mistakes.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This locking isn't needed. The only locking we need is when
we access prph registers but there is already a separate
lock for that.
Since we haven't returned from the mac80211's
IEEE80211_AMPDU_TX_OPERATIONAL ampdu_action, we cannot
receive any Tx frame for that sta / tid while enabling the
queue.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is not needed, we just need to tell the SCD not to use
that queue. We will reconfigure that queue when we will use
it again.
Clean up a bit the code on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Print some more info from the SCD's SRAM and dump the TRB
from the FH.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change its name to better reflect this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This macro gets the bufsize in bytes.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add locking to the dynamic loading code to prevent
corrupting the list if multiple device ever init at
the same time (which cannot happen for multiple PCI
devices, but could happen when different busses init
concurrently.)
Also remove a device from the list when it stops so
the list isn't left corrupted, including a fix from
Don to not crash when it was never added.
Reviewed-by: Donald H Fry <donald.h.fry@intel.com>
Tested-by: Donald H Fry <donald.h.fry@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Test procedure:
1. Start AP with security setting (e.g. WPA2)
2. Stop AP
3. Start AP with open security
Here it's observed that privacy is enabled in beacons and
probe responses.
This patch fixes it by checking the privacy parameter from
cfg80211_ap_settings. If privacy is not set in cfg80211_ap_settings,
set open authentication and no encryption in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a few kernel-doc descriptions that were missed
during mesh development.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
14e4:432c is found on some bcm63xx devices. The device is working fine
with b43.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MSI is enabled by default for most of the 4th generation
chips. Add this for AR9462 - this fixes PowerSave operation,
the chip was not entering Network-Sleep mode earlier.
With proper powering down of the MAC now, power consumption
in associated state is reduced considerably.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently 4 channels are scanned per scan command. if scan request
is issued by user during Tx traffic, radio will be out of channel
for "4 * per_chan_scan_time" for each scan command and will not be
able to receive Rx packets. This adds delay in data traffic. We can
minimize it by reducing number of channels scanned per scan command
in this scenario.
We can not always scan 1 channel per scan command due to limitation
of number of command buffers. So we add code to decide number of
channels scanned per scan command in associated state.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If scan operation is started when Tx traffic is already running,
driver locks Tx queue until it gets completed. With this logic
there is a delay for Tx packets.
This patch implements new approach to give Tx path higher priority
in this case. Driver internally sends multiple synchronous scan
commands to firmware when scan is requested by user. Now we will
make sure that Tx queue is empty everytime before sending next scan
command. If Tx queue isn't empty scan command will be postponsed by
20msec. This rule will be followed until Tx queue becomes empty or
timeout of 1 second happens. In case of timeout scan operation will
be aborted.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the scan time per channel for active scanning is set to
200ms. It takes quite a while to finsh scanning on all channels,
especially with a dual band configuration.
Change the per channel scan time settings to the following values:
passive scan: 110ms
active scan: 30ms
specific scan: 30ms
Above settings have been tested on x86 and arm platforms.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_check_bssid_list() originally tried to check if bssid->mac and
match_bssid are equal using compare_ether_addr() when it should use
!compare_ether_addr(). This check was added by commit
b5257c952d as part of workaround for
hardware issue.
Commit 2e42e4747e that replaced
compare_ether_addr with ether_addr_equal relieved that this compare
to be inverse of what it should be.
Compare was added as response to hardware bug, where bssid-list does
not contain BSSID and other information of currently connected AP
(spec insists that device must provide this information in the list
when connected). Lack bssid-data on current connection then causes
WARN_ON somewhere in cfg80211. Workaround was to check if bssid-list
returns current bssid and if it does not, manually construct bssid
information in other ways. And this workaround worked, with inverse
check. Which must mean that when hardware is experiencing the problem,
it's actually returning empty bssid-list and this check didn't make
any difference for workaround.
However inverse check causes workaround be activated when bssid-list
returns only entry, currently connected BSSID. That does not cause
problems in itself, just slightly more inaccurate information in
scan-list.
Cc: Joe Perches <joe@perches.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'cfg80211: fix interface combinations' ensures that if an interface
type is not advertised by the driver in any of the interface combinations
(via ieee80211_iface_combination) then it shall be treated as a single
incompatible interface. if there are more than one interfaces present
and changing them to incompatible interface type is not possible.
These checks will be properly handled by cfg80211_change_iface ->
cfg80211_can_change_interface.
this patch is dependent on 'cfg80211: fix interface combinations'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch is dependent on the patch "cfg80211: fix interface
combinations"
In ath9k currently we have ADHOC interface as a single incompatible
interface. when drv_add_interface is called during resume we got to
consider number of vifs already present in addition to checking the
drivers 'opmode' information about ADHOC. we incorrectly assume
an ADHOC interface is already present. Then we may miss some driver
specific data for the ADHOC interface after resume.
The above mentioned checks can be removed from the driver,
as the patch 'cfg80211: fix interface combinations' ensures that
if an interface type is not advertised by the driver in any of the
interface combinations(via ieee80211_iface_combination) then it shall
be treated as a single incompatible interface. Fixes the following
warning on suspend/resume with ibss interface.
ath: phy0: Cannot create ADHOC interface when other
interfaces already exist.
WARNING: at net/mac80211/driver-ops.h:12
ieee80211_reconfig+0x1882/0x1ca0 [mac80211]()
Hardware name: 2842RK1
wlan2: Failed check-sdata-in-driver check, flags: 0x0
Call Trace:
[<c01361b2>] warn_slowpath_common+0x72/0xa0
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<c0136283>] warn_slowpath_fmt+0x33/0x40
[<f8aaa7c2>] ieee80211_reconfig+0x1882/0x1ca0 [mac80211]
[<c06c1d1a>] ? mutex_lock_nested+0x23a/0x2f0
[<f8a95097>] ieee80211_resume+0x27/0x70 [mac80211]
[<fd177edf>] wiphy_resume+0x8f/0xa0 [cfg80211]
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to have different FW versioning for different FW binaries.
This is handled by appending different meta data in firmware
binaries.
kvalo: add an empty line before a debug message, use '0' instead of '0x00',
fix indentation
Signed-off-by: Naveen Singh <navesing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is frequent downlink throughput drop to 0 when operating
at the signal level between -42dBm to -53dBm. This has been root
caused to the delay in releasing pending a-mpdu subframes in
reorder buffer. Right now the timeout value is 400ms, there
is also a race condition where timeout handler can be delayed
to run at an extra timeout interval. This patch reduces the
timout interval to reasonable 100ms and makes sure releasing
pending frames are not skipped in the timeout handler by removing
the flag (rxtid->progress) which can delay the timeout logic.
Reported-by: Yu Yanzhi <yanzhiy@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are many places where tid data are accessed without
the lock (rxtid->lock), this can lead to a race condition
when the timeout handler for aggregatin reorder and the
receive function are getting executed at the same time.
Fix this race, but still there are races which can not
be fixed without rewriting the whole aggregation reorder
logic, for now fix the obvious ones.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support for dtim_period configuration in beacon.
kvalo: add a comment about ignoring the error, use vif_idx,
add \n to the warning message
Signed-off-by: Etay Luz <eluz@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Messages without newlines can be interleaved.
Avoid this by adding terminations.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The iwl-test flows were based on the cfg80211 testmode APIs.
To remove this coupling, the op mode (during the initialization
of the iwl_test object) is responsible to set the callbacks that
should be used by iwl-test to allocate skbs for events and replies
and to send events and replies.
The current op modes implement these callbacks based on the cfg80211
testmode APIs.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Create an object that will enacpsulate the testmode functionality
that is common to all op modes.
* Copy definitions from dvm/dev.h
* Copy the testmode logic from dvm/testmode.c
* Link iwl-test object into the iwlwifi module
* Modify DVM to use iwl-test object
Reviewed-by: Amit Beka <amit.beka@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Don't validate interface combinations on a stopped
interface. Otherwise we might end up being able to
create a new interface with a certain type, but
won't be able to change an existing interface
into that type.
This also skips some other functions when
interface is stopped and changing interface type.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a few kernel-doc descriptions that were missed
during development.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With LE/SMP the completion of a security level elavation from medium to
high is indicated by a HCI Encryption Key Refresh Complete event. The
necessary behavior upon receiving this event is a mix of what's done for
auth_complete and encryption_change, which is also where most of the
event handling code has been copied from.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
CC drivers/net/wireless/ti/wl18xx/main.o
drivers/net/wireless/ti/wl18xx/main.c: In function ‘wl18xx_conf_init’:
drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 2 has type ‘long unsigned int’ [-Wformat]
drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t’ [-Wformat]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 24398e39c8
Author: Johannes Berg <johannes.berg@intel.com>
Date: Wed Mar 28 10:58:36 2012 +0200
mac80211: set HT channel before association
removed IEEE80211_CONF_CHANGE_CHANNEL argument from ieee80211_hw_config,
which is required by iwl4965 driver, otherwise that driver does not
configure channel properly and is not able to associate.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
llcp_sock_getname() might get called before the LLCP socket was created.
This condition isn't checked, and llcp_sock_getname will simply deref a
NULL ptr in that case.
This exists starting with d646960 ("NFC: Initial LLCP support").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
