When aacraid spoofs READ_CAPACITY_16, it assumes that the data length
in the sg list is equal to allocation length in cdb. But sg can put
any value in scb so the driver needs to check both the data length in
the sg list and allocation length in cdb.
If allocation length is larger than the response length that the
driver expects, it clears the data buffer in the sg list to zero but
it doesn't need to do. Just setting resid is fine.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Adapter's Ignore Reset flag and insmod parameter boolean polarity
is incorrect in the driver.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Added support for MSI utilizing the aacraid.msi=1 parameter. This
patch adds some localized or like-minded janitor fixes. Since the
default is disabled, there is no impact on the code paths unless the
customer wishes to experiment with the MSI performance.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Luben Tuikov [mailto:ltuikov@yahoo.com] sez:
> Just as in your case and Tony's case, which I presume
> uses the same RAID firmware vendor, it would've
> probably been better if the RAID firmware vendor
> fixed the firmware to not set the VALID bit if the
> INFORMATION field is not valid.
Point taken regarding the aacraid driver. Dropped the VALID bit, and
then did some cleanup/simplification of the set_sense procedure and
the associated parameters. Mike did some preliminary tests when the
VALID bit was dropped before the 'Re: [PATCH] [SCSI] sd: make error
handling more robust' patches came on the scene. The change in the
SCSI subsystem does make this enclosed aacraid patch unnecessary, so
this aacraid patch is merely post battle ground cleanup. If the
simplification is an issue, repugnant, too much for a back-port to the
stable trees or clouds the point, this patch could be happily
distilled down to:
diff -ru a/drivers/scsi/aacraid/aachba.c b/drivers/scsi/aacraid/aachba.c
--- a/drivers/scsi/aacraid/aachba.c 2008-02-06 16:26:45.834938955 -0500
+++ b/drivers/scsi/aacraid/aachba.c 2008-02-06 16:32:01.109035329 -0500
@@ -865,7 +865,7 @@
u32 residue)
{
- sense_buf[0] = 0xF0; /* Sense data valid, err code 70h (current error) */
+ sense_buf[0] = 0x70; /* Sense data invalid, err code 70h (current error) */
sense_buf[1] = 0; /* Segment number, always zero */
if (incorrect_length) {
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The cards being added are supported in a limited sense already through
family matching, but we needed to add some functionality to the driver
to expose selectively the physical drives. These Physical drives are
specifically marked to not be part of any array and thus are declared
JBODs (Just a Bunch Of Drives) for generic SCSI access.
We report that this is the second patch in a set of two, but merely
depends on the stand-alone functionality of the first patch which adds
in that case the ability to report a driver feature flag via sysfs. We
leverage that functionality by reporting that this driver now supports
this new JBOD feature for the controller so that the array management
applications may react accordingly and guide the user as they manage
the controller.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
I was amazed at how much embedded space was present in the aacraid
driver source files. Just selected five files from the set to clean up
for now and the attached patch swelled to 73K in size!
- Removed trailing space or tabs
- Removed spaces embedded within tabs
- Replaced leading 8 spaces with tabs
- Removed spaces before )
- Removed ClusterCommand as it was unused (noticed it as one triggered by above)
- Replaced scsi_status comparison with 0x02, to compare against SAM_STATUS_CHECK_CONDITION.
- Replaced a long series of spaces with tabs
- Replaced some simple if...defined() with ifdef/ifndef
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The promised min_t() cleanup. Purely cosmetic.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in
several LLDs. It's a preparation for the future changes to remove
sense_buffer array in scsi_cmnd structure.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Due to an internal limit associated with the AdapterTypeText field,
SMC required a product ID that overloaded the combined vendor and
product ID. A decision was made to ship the SMC products without a
vendor string dropping the defacto space that used to delineate vendor
and product to boot. To correct this, we needed to adjust the code in
the driver to parse out the vendor and product strings for the
adapter. We match of 'AOC' in the AdapterTypeText, if so we set the
vendor to SMC and place the entire AdapterTypeText into the product
field.
This only affects the cosmetic presentation of the Adapter vendor and
product in the logs and in sysfs.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some architectures require a call to flush_kernel_dcache_page for
processor spoofed DMA operations.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Big endian systems issues discovered in the aacraid driver. Somewhat
reverses a patch from November 7th of last year that removed swap
operations because they formerly were being assigned to an u8 array
when they should have been assigned to an le32 array.
This patch is largely inert for any little endian processor
architecture. It resolves a bug in delivering the BlinkLED AIF event
to registered applications when the adapter or associated hardware was
reset due to ill health. A rare corner case occurrence, also largely
unnoticed by any as it was a new (untested!) feature.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The parameter 'info' is reused, renamed the second to sinfo to
represent supplemental adapter info, to suppress compile warning
message.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Report the RAID level string for the SCSI device representing the
array. Report is in /sys/class/scsi_device/#:#:#:#/device/level.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
aacraid.cache parameter, Disable Queue Flush commands:
bit 0 - Disable FUA in WRITE SCSI commands
bit 1 - Disable SYNCHRONIZE_CACHE SCSI command
bit 2 - Disable only if Battery not protecting adapter supplied Cache
e.g.: aacraid.cache=7 will disable the FUA and SYNCHRONIZE_CACHE
commands if the adapter has reported that it's cache is battery backed
up.
This parameter permits experimentation with tradeoffs between
performance and caching policy.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As reported in http://bugzilla.kernel.org/show_bug.cgi?id=3D9133 it was
discovered that the PERC line of controllers lacked a key 64 bit
ScatterGather capable SCSI pass-through function. The adapters are still
capable of 64 bit ScatterGather I/O commands, but these two can not be
mixed. This problem was exacerbated by the introduction of the SCSI
Generic access to the DASD physical devices.
The fix for users before this patch is applied is aacraid.dacmode=3D0 on
the kernel command line to disable 64 bit I/O.
The enclosed patch introduces a new adapter quirk and tries to limp
along by enabling pass-through in situations where memory is 32 bit
addressable on 64 bit machines, or disable the pass-through functions
altogether. I expect that the check for 32 bit addressable memory to be
controversial in that it can be incorrect in non-Dell non-Intel systems
that PERC would never be installed under, the alternative is to disable
pass-through in all cases which could be reported as another regression.
Pass-through is used for SCSI Generic access to the physical devices, or
for the management applications to properly function.
In systems where this patch has disabled pass-through because it is
unsupportable in combination with I/O performance, the user can choose
to enable pass-through by turning off dacmode (aacraid.dacmode=3D0) or
limiting the discovered kernel memory (mem=3D4G) with an associated loss
in runtime performance. If we chose instead to turn off 64 bit dacmode
for the adapters with this quirk, then this would be reported as another
regression.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
On Wed, Nov 07, 2007 at 01:51:44PM -0500, Salyzyn, Mark wrote:
> Christoph Hellwig [mailto:hch@infradead.org] sez:
> > Did anyone run the driver through sparse to see if we have
> > more issues like this?
>
> There are some warnings from sparse, none like this one. I will deal
> with the warnings ...
Actually there are a lot of endianess warnings, fortunately most of them
harmless. The patch below fixes all of them up (including the ones in
the patch I replied to), except for aac_init_adapter which is really odd
and I don't know what to do.
[jejb fixed up rejections and checkpatch issues]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some of our vendors have requested that our adapters ignore the hardware
reset attempts during recovery and have enforced this with changes in
Adapter Firmware. Some of our customers have requested the option to be
able to reset the adapter under adverse adapter failure, we even had a
few defects reported here considering it a regression that the Adapter
could not be reset. This patch addresses this dichotomy. The user can
force the adapter to be reset if it supports the IOP_RESET_ALWAYS
command, in cases where the adapter has been programmed to ignore the
reset, by setting the aacraid.check_reset parameter to a value of -1.
The driver will not reset an Adapter that does not support the reset
command(s).
This patch also fixes and cleans up some of the logic associated with
resetting the adapter.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Too generic, clashes with ISDN.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Customer running an application that issues SYNCHRONIZE_CACHE calls
directly noticed the broad stroke of the current implementation in the
aacraid driver resulting in multiple applications feeding I/O to the
storage causing the issuing application to stall for long periods of
time. By only waiting for the current WRITE commands, rather than all
commands, to complete; and those that are in range of the
SYNCHRONIZE_CACHE call that would associate more tightly with the
issuing application before telling the Firmware to flush it's dirty
cache, we managed to reduce the stalling. The Firmware itself still
flushes all the dirty cache associated with the array ignoring the
range, it just does so in a more timely manner.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Minor unimportant cuttings from the floor bundled in with a version
stamp update. Only controversial change is the dropping of Alan Cox
copyright on the nark.c module since that file has no code written by
him in it.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Report VPD inquiry page 0x80 with an unique array creation serial
number (CUID). When an array is created, the metadata stored on the
physical drives gets an unique serial number. This serial number
remains constant through array morphing or migration to other
controllers. This patch is a forward port and modification to survive
morphing and migration operations, of a similar piece of
(un-attributed author) code added to the SLES10 SP1 aacraid driver.
To test the results of the patch, observe that /dev/disk/by-id/
entries will show up for the arrays resulting from the udev rules.
Also, as per the udev rules, 'scsi_id -g -x -a -s /block/sd? -d
/dev/sd?' will report the ID_SERIAL as constructed from the inquiry
data.
It was reported to me that the 'ADPT' leading the serial number was bad
form, that the inquiry vendor field was enough to differentiate the
storage uniquely. Subsequent search found that another Adaptec AAC based
driver reported the 8 hex serial number only without such adornments, so
dropped ADPT to match. Resubmitting the patch with this alteration.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
During an Adapter Initiated scan request, the query disk ioctl reports a
value of 2 rather than 1 for the valid field. This presents a problem
for some legacy management applications.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Support displaying long serial number information. Reuse sysfs handler
internally as helper.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch is more like a spelling correction than a fix. It was
discovered that if we had a busy status return from the Adapter for the
SCSI srb command to a physical component, that we returned
DID_NO_CONNECT rather than what one would expect DID_BUS_BUSY.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add the ability for an application to issue a hardware reset to the
adapter via sysfs. Typical uses include restarting the adapter after it
has been flashed. Bumped revision number for the driver and added a
feature to periodically check the adapter's health (check_interval),
update the adapter's concept of time (update_interval) and block
checking/resetting of the adapter (check_reset).
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sundry cleanups:
1) Use kzalloc instead of kmalloc.
2) Make sure probe worked before recalling the SCSI command to finalize
processing.
3) _aac_probe_container2 and _aac_probe_container1 return value goes
unused, change return to void.
4) Use a lower depth pointer reference to pick up the driver instance
variable.
5) Although effectively unused except to fake for scsicmd validity, set
the scsi_done in probe code to aac_probe_container_callback1 instead of
the less valid dummy reference to _aac_probe_container1.
6) SCp.phase is set in aac_valid_context, drop setting up this value in
caller when unnecessary.
7) take container target id at the beginning, rather than referencing
scmd_id() to pick it up.
There should be no side effects or functionality changes.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/jazz_esp.c
Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Under some conditions associated with the unclean transition to kdump,
the aacraid adapters will view the array as foreign and not export it to
prevent access and data manipulation. The solution is to submit a commit
configuration to export the devices since this is a expected behavior
when transitioning to a kdump kernel.
This patch adds the aacraid.reset_devices flag and when either this or
the global reset_devices flag is set, ensures that a commit config is
issued and extends the startup_timeout if it is set less than 5 minutes.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Back in the beginning of last year we disabled mode page 8 and mode page
3f requests through device quirk bits instead of enhancing the driver to
respond to these mode pages because there was no apparent added value.
The Firmware that supports the new communication commands supports the
ability to force a write around of the adapter cache on a command by
command basis. In the attached patch we enable mode page 8 and 3f and
spoof the results as needed in order to *convince* the layers above to
submit writes with the FUA (Force Unit Attention) bit set if the file
system or application requires it, if the Firmware supports the write
through, or instead to submit a SYNCHRONIZE_CACHE if the Firmware does
not. The added value here is for file systems that benefit from this
functionality and for clustering or redundancy scenarios.
Caveats: By convince, we are responding with a minimal short 3 byte
content mode page 8, with only the data the SCSI layer needs and that we
can fill confidently. Applications that require the customarily larger
mode page 8 results may be confused by this(?). The FUA, or the
SYNCHRONIZE_CACHE only affect the cache on the controller. Our firmware
by default ensure that the underlying physical drives of the array have
their cache turned off so normally this is not a problem.
This attached patch is against current scsi-misc-2.6 and was unit tested
on RHEL5. Since this is a feature enhancement, it should not be
considered for any current stabilization efforts.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Thanks for the help from Steve Fox and Duane Cox investigating this
issue, I'd like to report that we found the problem. The issue is with
the patch Steve Fox isolated below, by not accommodating older adapters
properly and issuing a command they do not support when retrieving
storage parameters about the arrays. This simple patch resolves the
problem (and more accurately mimics the logic of the original code
before the patch).
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Adapter build date that is to be printed on instantiation was not
displayed as a result of the supplemental adapter information structure
not being in sync with the Firmware; the driver took an early test cycle
version that had a miss-sized padded region at the head and the
structure was not re-checked at the end of qualification. The Build Date
was not a priority and is merely a cosmetic enhancement, and the wrong
location for the start of the structure member would not induce any
side-effect problems. We updated the structure to match the actual
format, and added the TSID (Tech Support Identification) value print,
should it be present, to the adapter instantiation announcements during
driver load.
This later enhancement should improve the relationship between Service
folk & Tech Support if the printed value of the TSID found it's way into
the circular file labeled G...
Neither of these values show in sysfs (yet).
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is some residual cleanup of the last series of patches and the
need to bump the revision number to draw the line in the sand.
The cmd->SCp.phase is set in the aac_valid_context routine, then set
again to the same value following it's return. The cmd->scsi_done is set
twice in the aac_queuecommand routine. Free up the scsidev FILO in
aac_probe_container as it is not needed further down the function in any
case. Improve the efficiency of the abort handler kernel print
parameters. Bump revision number of driver to approximate the equivalent
in the Adaptec supplied version.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Captured a panic on an older kernel where an application issuing
commands via sg was sending requests that lacked a request_buffer, thus
the buffer pointer used in aac_internal_transer was NULL. The
application was fixed closing the issue, but felt it was advised to
immunize the driver against the eventuality.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
This set of fixes improve error handling stability of the driver. A popular
manifestation of the problems is an NULL pointer reference in the interrupt
handler when referencing portions of the scsi command context, or in the
scsi_done handling when an offlined device is referenced.
The aacraid driver currently does not get notification of orphaned command
completions due to devices going offline. The driver also fails to handle the
commands that are finished by the error handler, and thus can complete again
later at the hands of the adapter causing situations of completion of an
invalid scsi command context. Test Unit Ready calls abort assuming that the
abort was successful, but are not, and thus when the interrupt from the adapter
occurs, they reference invalid command contexts. We add in a TIMED_OUT flag to
inform the aacraid FIB context that the interrupt service should merely release
the driver resources and not complete the command up. We take advantage of this
with the abort handler as well for select abortable commands. And we detect and
react if a command that can not be aborted is currently still outstanding to
the controller when reissued by the retry mechanism.
Signed-off-by: Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
This little patch removes the ',cid)' container identification argument
from some of the functions. The argument is used in some cases as merely
a debug helper and thus not used, and in others, the value can be
quickly acquired from the scsi command in their single solitary use in
the procedure rather than wasting resources on passing the argument in
from above.
Signed-off-by: Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
The aac_probe_container call blocks. This is an issue because it is called on
occasion in the context of the queuecommand handler. Once in a blue moon this
has resulted in a kernel panic sleeping during interrupt; or problems with some
embedded system versions of the kernel that depend on queuecommand to not
block. This ugly patch rewrites the aac_probe_container call into a new routine
_aac_probe_container that is an asynchronous state machine to complete the
series of operations. The legacy blocking aac_probe_container call used in
other areas of the driver (during initialization scanning for all targets and
in the separate hot-add/remove [aacraid] thread) merely issues
_aac_probe_container and then simple spins calling schedule() waiting for
completion.
Signed-off-by: Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Received from Mark Salyzyn,
Take the expose_physicals flag and allow the user to select default (physicals
available via /dev/sg), exposed (physicals available via /dev/sd for
experimental reasons) and hidden (physicals blocked from all access). This
expands the functionality of the previous expose_physicals insmod parameter
which was added to support some experimental configurations.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
Replace all if/else packet formations with platform function calls. This is in
recognition of the proliferation of read and write packet types, and in the
need to migrate to up-and-coming packets for new products.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Run this:
#!/bin/sh
for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
echo "De-casting $f..."
perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
done
And then go through and reinstate those cases where code is casting pointers
to non-pointers.
And then drop a few hunks which conflicted with outstanding work.
Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Received from Mark Salyzyn:
I am placing this functionality into an insmod parameter. Normally the physical
components are exported to sg, and are blocked from showing up in sd.
Note that the pass-through I/O path via the driver through the Firmware to the
physical disks is not an optimized path, the card is designed for Hardware
RAID, elevator sorting and caching. This should not be used as a means for
utilizing the aacraid based controllers as a generic scsi/SATA/SAS controller,
performance should suck by a few percentage points, any RAID meta-data on the
drives will confuse the controller about who owns the drives and there is a
high risk of destroying content in both directions. Unreliable and for
experimentation or strange controlled circumstances only.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn:
Basically cleanup, nothing here will have an affect. Adjusting some
error codes, removing superfluous definitions and code fragments.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
If the adapter is in blinkled (Firmware Assert) when error recovery
timeout actions have been triggered, perform an adapter warm reset and
restart the initialization.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
The enclosed patch cleans up some code fragments, adds some paranoia
(unproven causes of potential driver failures).
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Various scsi drivers use scsi_cmnd.buffer and scsi_cmnd.bufflen in their
queuecommand functions. Those fields are internal storage for the
midlayer only and are used to restore the original payload after
request_buffer and request_bufflen have been overwritten for EH. Using
the buffer and bufflen fields means they do very broken things in error
handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
Add the ability to adjust for unusual corner case failures. Both of
these additional module parameters deal with embedded, non-intel or
complicated system scenarios.
Aif_timeout can be increased past the default 2 minute timeout to drop
application registrations when a system has an unusually high event load
resulting from continuing management requests, or simultaneous builds,
or sluggish user space as a result of system load.
Startup_timeout can be increased past the default 3 minute timeout to
drop an adapter initialization for systems that have a very large number
of targets, or slow to spin-up targets, or a complicated set of array
configurations that extend the time for the firmware to declare that it
is operational. This timeout would only have an affect on non-intel
based systems, as the (more patient) BIOS would generally be where the
startup delay would be dealt with.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
Slight space and speed efficiency improvement.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Fix module param
Update driver version.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Remove superfluous code, optimize code, harden code, cast code, correct
some text, use msleep instead of schedule_timeout_interruptible. No
bugs.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
The loss of the ownership flags, despite their flaws, in the scsi
command were sorely missed and are reinstated more accurately in the
aacraid driver to track commands and permit us to properly handle error
recovery actions.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Clean up the remaining scsi id access methods, drop ID_LUN_TO_CONTAINER
macro.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace all occurences of 0xff.. in calls to function pci_set_dma_mask()
and pci_set_consistant_dma_mask() with the corresponding DMA_xBIT_MASK from
linux/dma-mapping.h.
Signed-off-by: Matthias Gehre <M.Gehre@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Received From Mark Salyzyn.
In order to support user tools accessing the array components (SMART,
Mode Page information, Cache page adjustments, WWN determination,
Firmware updates etc), we take advantage of the no_uld_attach flag and
deprecate the code that filters Inquiries to block the requests to array
components. The quirk prevents the sd layer from attaching to the
components.
We also took the opportunity to balance the queue depths based on the
total adapter queue depth to the array devices to reduce the chances of
starvation.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn,
Reduce the possibility of namespace collision. Prefix with aac_.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
The return data from a read capacity 16 needs to have RTO_EN and PROT_EN
zeroed out.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Wrap a highly common idiom. Makes the code easier to read, helps pave
the way for sdev->{id,channel} removal, and adds a token that can easily
by grepped-for in the future.
There are a couple sdev_id() and scmd_printk() updates thrown in as well.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
This patch adds the 'new comm' interface, which modern AAC based
adapters that are less than a year old support in the name of much
improved performance. These modern adapters support both the legacy and
the 'new comm' interfaces.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
This patch uses the adapter supplemental information AdapterTypeText as
the default for the array name.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Mark Haverkamp <markh@osdl.org>
Received from Mark Salyzyn.
This patch changes the driver over to utilizing the DMA_64BIT_MASK and
DMA_32BIT_MASK manifests.
Applies to the scsi-rc-fixes-2.6 git tree.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Rejects fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
The size of the command packet's scatter gather list maximum size was
miscalculated in the low range leading to the driver initialization
limiting the maximum i/o size that could go to the Adapter. There were
no negative operational side effects resulting from this bad math, only
a subtle limit in performance of the Adapter at the top end of the
range.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
In the rare instances where the adapter, or the motherboard, is
misbehaving; driver initialization or shutdown becomes problematic. By
introducing a 3 minute timeout on the first interrupt driven command
during initialization, or the issuance of the adapter shutdown command
during driver unload, we can resolve the lockup problems induced by
common (but rare) hardware misbehaviors.
The timeout during initialization, should it occur, is accompanied by a
message presented to the console and the logs indicating that the user
should inspect and resolve problems with interrupt routing.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
Hotplug sniffs the AIFs (events) from the adapter and if a container
change resulting in the device going offline (container zero), online
(container zero completed) or changing capacity (morph) it will take
actions by calling the appropriate API.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
There are a few adapters that are capable of creating devices with this large
of a capacity, but now that we have the large fib support in, the management
applications will be capable of generating them. The problem is, once they are
created, the driver will not be able to access the devices correctly without
this patch.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This was noticed by Doug Bazamic and the fix found by Mark Salyzyn at
Adaptec.
There was an error in the BUG_ON() statement that validated the
calculated fib size which can cause the driver to panic.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes the bad assumption of the aacraid driver with use_sg.
I used the 3w-xxxx driver fix as a guide for this.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The cmd->timeout field has been obsolete for a while now. While looking
to remove it, I came across this use in the aacraid driver. It looks
like you want to initialise the firmware with the current timeout of the
command (in seconds), so the value I think you should be using is
cmd->timeout_per_command.
Acked by: Mark Haverkamp <markh@osdl.org>
Acked by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
This patch adds support for the new raw io command. This new command
offers much larger io commands, is more friendly to the internal firmware
structure requiring less translation efforts by the firmware and offers
support for targets greater than 2TB (patch to support >2TB will
be sent in the future).
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec:
This patch removes the duplicate code in the write_callback command
completion handler, and renames read_callback to io_callback. Optimized
the lba calculation into the debug print routine macro to optimize the
i/o code path.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch add the following products to the driver:
IBM ServeRAID 8i
ICP 9014R0
ICP 9024R0
ICP 9047MA
ICP 9087MA
ICP 9085LI
ICP 5085AU
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New code from the Adaptec driver. Performance enhancement for newer
adapters. I hope that this isn't too big for a single patch. I believe
that other than the few small cleanups mentioned, that the changes are
all related.
- Added Variable FIB size negotiation for new adapters.
- Added support to maximize scatter gather tables and thus permit
requests larger than 64KB/each.
- Limit Scatter Gather to 34 elements for ROMB platforms.
- aac_printf is only enabled with AAC_QUIRK_34SG
- Large FIB ioctl support
- some minor cleanup
Passes sparse check.
I have tested it on x86 and ppc64 machines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch addresses the sparse -Wbitwise warnings that Christoph wanted
me to eliminate. This mostly consisted of making data structure
elements of hardware associated structures the __le* equivalent.
Although there were a couple places where there was mixing of cpu and le
variable math. These changes have been tested on both an x86 and ppc
machine running bonnie++. The usage of the LE32_ALL_ONES macro has been
eliminated.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes some needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
