When allocating memory pages for context memory, if the last page table
should be fully populated, the current code will set nr_pages to 0 when
calling bnxt_alloc_ctx_mem_blk(). This will cause the last page table
to be completely blank and causing some RDMA failures.
Fix it by setting the last page table's nr_pages to the remainder only
if it is non-zero.
Fixes: 08fe9d1816 ("bnxt_en: Add Level 2 context memory paging support.")
Reported-by: Eric Davis <eric.davis@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_hwrm_check_pf_rings(), add the proper flag to test the NQ
resources. Without the proper flag, the firmware will change
the NQ resource allocation and remap the IRQ, causing missing
IRQs. This issue shows up when adding MQPRIO TX queues, for example.
Fixes: 36d65be9a8 ("bnxt_en: Disable MSIX before re-reserving NQs/CMPL rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, TX is given a budget which is consumed by stmmac_tx_clean()
and stmmac_rx() is given the remaining non-consumed budget.
This is wrong and in case we are sending a large number of packets this
can starve RX because remaining budget will be low.
Let's give always the same budget for RX and TX clean.
While at it, check if we missed any interrupts while we were in NAPI
callback by looking at DMA interrupt status.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Watchdog can be disabled by platform definitions but currently we are
initializing the descriptors before checking if Watchdog must be
disabled or not.
Fix this by checking earlier if user wants Watchdog disabled or not.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if CBS is currently supported before trying to configure it in HW.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In DMA interrupt handler we were clearing all interrupts status, even
the ones that were not active. Fix this and only clear the active
interrupts.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit b7d0f08e91, the enable / disable of PCI device is not
managed which will result in IO regions not being automatically unmapped.
As regions continue mapped it is currently not possible to remove and
then probe again the PCI module of stmmac.
Fix this by manually unmapping regions on remove callback.
Changes from v1:
- Fix build error
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Fixes: b7d0f08e91 ("net: stmmac: Fix WoL for PCI-based setups")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linux 5.0-rc1 shows following warning on bpi-r2/mt7623 bootup:
[ 5.170597] WARNING: CPU: 3 PID: 1 at drivers/net/phy/phy.c:548 phy_start_aneg+0x110/0x144
[ 5.178826] called from state READY
....
[ 5.264111] [<c0629fd4>] (phy_start_aneg) from [<c0e3e720>] (mtk_init+0x414/0x47c)
[ 5.271630] r7:df5f5eec r6:c0f08c48 r5:00000000 r4:dea67800
[ 5.277256] [<c0e3e30c>] (mtk_init) from [<c07dabbc>] (register_netdevice+0x98/0x51c)
[ 5.285035] r8:00000000 r7:00000000 r6:c0f97080 r5:c0f08c48 r4:dea67800
[ 5.291693] [<c07dab24>] (register_netdevice) from [<c07db06c>] (register_netdev+0x2c/0x44)
[ 5.299989] r8:00000000 r7:dea2e608 r6:deacea00 r5:dea2e604 r4:dea67800
[ 5.306646] [<c07db040>] (register_netdev) from [<c06326d8>] (mtk_probe+0x668/0x7ac)
[ 5.314336] r5:dea2e604 r4:dea2e040
[ 5.317890] [<c0632070>] (mtk_probe) from [<c05a78fc>] (platform_drv_probe+0x58/0xa8)
[ 5.325670] r10:c0f86bac r9:00000000 r8:c0fbe578 r7:00000000 r6:c0f86bac r5:00000000
[ 5.333445] r4:deacea10
[ 5.335963] [<c05a78a4>] (platform_drv_probe) from [<c05a5248>] (really_probe+0x2d8/0x424)
maybe other boards using this generic driver are affected
v2:
optimization:
- phy_set_max_speed() is only needed if you want to reduce the
max speed, typically if the PHY supports 1Gbps but the MAC
supports 100Mbps only.
- The pause parameters are autonegotiated. Except you have a specific
need you normally don't need to manually fiddle with this.
- phy_start_aneg() is called implicitly by the phylib state machine,
you shouldn't call it manually except you have a good excuse.
- netif_carrier_on/netif_carrier_off in mtk_phy_link_adjust() isn't
needed. It's done by phy_link_change() in phylib.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A network device stack with multiple layers of bonding devices can
trigger a false positive lockdep warning. Adding lockdep nest levels
fixes this. Update the level on both enslave and unlink, to avoid the
following series of events ..
ip netns add test
ip netns exec test bash
ip link set dev lo addr 00:11:22:33:44:55
ip link set dev lo down
ip link add dev bond1 type bond
ip link add dev bond2 type bond
ip link set dev lo master bond1
ip link set dev bond1 master bond2
ip link set dev bond1 nomaster
ip link set dev bond2 master bond1
.. from still generating a splat:
[ 193.652127] ======================================================
[ 193.658231] WARNING: possible circular locking dependency detected
[ 193.664350] 4.20.0 #8 Not tainted
[ 193.668310] ------------------------------------------------------
[ 193.674417] ip/15577 is trying to acquire lock:
[ 193.678897] 00000000a40e3b69 (&(&bond->stats_lock)->rlock#3/3){+.+.}, at: bond_get_stats+0x58/0x290
[ 193.687851]
but task is already holding lock:
[ 193.693625] 00000000807b9d9f (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0x58/0x290
[..]
[ 193.851092] lock_acquire+0xa7/0x190
[ 193.855138] _raw_spin_lock_nested+0x2d/0x40
[ 193.859878] bond_get_stats+0x58/0x290
[ 193.864093] dev_get_stats+0x5a/0xc0
[ 193.868140] bond_get_stats+0x105/0x290
[ 193.872444] dev_get_stats+0x5a/0xc0
[ 193.876493] rtnl_fill_stats+0x40/0x130
[ 193.880797] rtnl_fill_ifinfo+0x6c5/0xdc0
[ 193.885271] rtmsg_ifinfo_build_skb+0x86/0xe0
[ 193.890091] rtnetlink_event+0x5b/0xa0
[ 193.894320] raw_notifier_call_chain+0x43/0x60
[ 193.899225] netdev_change_features+0x50/0xa0
[ 193.904044] bond_compute_features.isra.46+0x1ab/0x270
[ 193.909640] bond_enslave+0x141d/0x15b0
[ 193.913946] do_set_master+0x89/0xa0
[ 193.918016] do_setlink+0x37c/0xda0
[ 193.921980] __rtnl_newlink+0x499/0x890
[ 193.926281] rtnl_newlink+0x48/0x70
[ 193.930238] rtnetlink_rcv_msg+0x171/0x4b0
[ 193.934801] netlink_rcv_skb+0xd1/0x110
[ 193.939103] rtnetlink_rcv+0x15/0x20
[ 193.943151] netlink_unicast+0x3b5/0x520
[ 193.947544] netlink_sendmsg+0x2fd/0x3f0
[ 193.951942] sock_sendmsg+0x38/0x50
[ 193.955899] ___sys_sendmsg+0x2ba/0x2d0
[ 193.960205] __x64_sys_sendmsg+0xad/0x100
[ 193.964687] do_syscall_64+0x5a/0x460
[ 193.968823] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: 7e2556e400 ("bonding: avoid lockdep confusion in bond_get_stats()")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some lines that have indentation issues, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are handful of lines that have indentation issues, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BUG: unable to handle kernel NULL pointer dereference at 00000000000000d1
Call Trace:
? napi_gro_frags+0xa7/0x2c0
tun_get_user+0xb50/0xf20
tun_chr_write_iter+0x53/0x70
new_sync_write+0xff/0x160
vfs_write+0x191/0x1e0
__x64_sys_write+0x5e/0xd0
do_syscall_64+0x47/0xf0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
I think there is a subtle race between sending a packet via tap and
attaching it:
CPU0: CPU1:
tun_chr_ioctl(TUNSETIFF)
tun_set_iff
tun_attach
rcu_assign_pointer(tfile->tun, tun);
tun_fops->write_iter()
tun_chr_write_iter
tun_napi_alloc_frags
napi_get_frags
napi->skb = napi_alloc_skb
tun_napi_init
netif_napi_add
napi->skb = NULL
napi->skb is NULL here
napi_gro_frags
napi_frags_skb
skb = napi->skb
skb_reset_mac_header(skb)
panic()
Move rcu_assign_pointer(tfile->tun) and rcu_assign_pointer(tun->tfiles) to
be the last thing we do in tun_attach(); this should guarantee that when we
call tun_get() we always get an initialized object.
v2 changes:
* remove extra napi_mutex locks/unlocks for napi operations
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is deleted from a bridge port we should not change the PVID
unless the deleted VLAN is the PVID.
Fixes: fe9ccc785d ("mlxsw: spectrum_switchdev: Don't batch VLAN operations")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a VLAN on a port can trigger the offload of a VXLAN tunnel which
is already a member in the VLAN. In case the configuration of the VXLAN
is not supported, the driver would return -EOPNOTSUPP.
This is problematic since bridge code does not interpret this as error,
but rather that it should try to setup the VLAN using the 8021q driver
instead of switchdev.
Fixes: d70e42b22d ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers are not supposed to return errors in switchdev commit phase if
they returned OK in prepare phase. Otherwise, a WARNING is emitted.
However, when the offloading of a VXLAN tunnel is triggered by the
addition of a VLAN on a local port, it is not possible to guarantee that
the commit phase will succeed without doing a lot of work.
In these cases, the artificial division between prepare and commit phase
does not make sense, so simply do the work in the prepare phase.
Fixes: d70e42b22d ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VXLAN is a loadable module, MLXSW_SPECTRUM must not be built-in:
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c:2547: undefined
reference to `vxlan_fdb_find_uc'
Add Kconfig dependency to enforce usable configurations.
Fixes: 1231e04f5b ("mlxsw: spectrum_switchdev: Add support for VxLAN encapsulation")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that lag port TX is disabled before mlxsw_sp_port_lag_leave()
is called and prevent from possible EMAD error.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removal of the mlxsw driver on Spectrum-2 platforms hits an ASSERT_RTNL()
in Spectrum-2 ACL Bloom filter and in ERP removal paths. This happens
because the multicast router implementation in Spectrum-2 relies on ACLs.
Taking the RTNL lock upon driver removal is useless since the driver first
removes its ports and unregisters from notifiers so concurrent writes
cannot happen at that time. The assertions were originally put as a
reminder for future work involving ERP background optimization, but having
these assertions only during addition serves this purpose as well.
Therefore remove the ASSERT_RTNL() in both places related to ERP and Bloom
filter removal.
Fixes: cf7221a4f5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When writing to C-TCAM, mlxsw driver uses cregion->ops->entry_insert().
In case of C-TCAM HW insertion error, the opposite action should take
place.
Add error handling case in which the C-TCAM region entry is removed, by
calling cregion->ops->entry_remove().
Fixes: a0a777b940 ("mlxsw: spectrum_acl: Start using A-TCAM")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This soft dependency works around an issue where sometimes the genphy
driver is used instead of the dedicated PHY driver. The root cause of
the issue isn't clear yet. People reported the unloading/re-loading
module r8169 helps, and also configuring this soft dependency in
the modprobe config files. Important just seems to be that the
realtek module is loaded before r8169.
Once this has been applied preliminary fix 38af4b903210 ("net: phy:
add workaround for issue where PHY driver doesn't bind to the device")
will be removed.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been noticed that some phys do not have the registers
required by the previous implementation.
To fix this, instead of using phy_read, the required information
is extracted from the phy_device structure.
fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is unreadable enough without indenting mismatches
and unnecessary line breaks.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid log spam caused by trying to read counters from the chip whilst
it is in a PCI power-save state.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=107421
Fixes: 1ef7286e7f ("r8169: Dereference MMIO address immediately before use")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_{,un}map_sg are deprecated and replaced by dma_{,un}map_sg. This is
especially relevant since the rest of the driver uses the DMA API. Fix
the driver to use the replacement APIs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch solves a crash at the time of mlx4 driver unload or system
shutdown. The crash occurs because dma_alloc_coherent() returns one
value in mlx4_alloc_icm_coherent(), but a different value is passed to
dma_free_coherent() in mlx4_free_icm_coherent(). In turn this is because
when allocated, that pointer is passed to sg_set_buf() to record it,
then when freed it is re-calculated by calling
lowmem_page_address(sg_page()) which returns a different value. Solve
this by recording the value that dma_alloc_coherent() returns, and
passing this to dma_free_coherent().
This patch is roughly equivalent to commit 378efe798e ("RDMA/hns: Get
rid of page operation after dma_alloc_coherent").
Based-on-code-from: Christoph Hellwig <hch@lst.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new ability added to the driver to use mii_bus to handle MII related
ioctls is causing compile issues when the driver is compiled into the
kernel (i.e. not a module).
The problem was in selecting MDIO_DEVICE instead of the preferred PHYLIB
Kconfig option. The reason being that MDIO_DEVICE had a dependency on
PHYLIB and would be compiled as a module when PHYLIB was a module, no
matter whether ixgbe was compiled into the kernel.
CC: Dave Jones <davej@codemonkey.org.uk>
CC: Steve Douthit <stephend@silicom-usa.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reviewed-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds MTU default value to qmap network interface in
order to avoid "RTNETLINK answers: No buffer space available"
error when setting an ipv6 address.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 308c6cafde ("net: hns: All ports can not work when insmod hns ko
after rmmod.") add phy_stop in hns_nic_init_phy(), In the branch of "net",
this method is effective, but in the branch of "net-next", it will cause
a WARNING when hns modules loaded, reference to commit 2b3e88ea65 ("net:
phy: improve phy state checking"):
[10.092168] ------------[ cut here ]------------
[10.092171] called from state READY
[10.092189] WARNING: CPU: 4 PID: 1 at ../drivers/net/phy/phy.c:854
phy_stop+0x90/0xb0
[10.092192] Modules linked in:
[10.092197] CPU: 4 PID:1 Comm:swapper/0 Not tainted 4.20.0-rc7-next-20181220 #1
[10.092200] Hardware name: Huawei TaiShan 2280 /D05, BIOS Hisilicon D05 UEFI
16.12 Release 05/15/2017
[10.092202] pstate: 60000005 (nZCv daif -PAN -UAO)
[10.092205] pc : phy_stop+0x90/0xb0
[10.092208] lr : phy_stop+0x90/0xb0
[10.092209] sp : ffff00001159ba90
[10.092212] x29: ffff00001159ba90 x28: 0000000000000007
[10.092215] x27: ffff000011180068 x26: ffff0000110a5620
[10.092218] x25: ffff0000113b6000 x24: ffff842f96dac000
[10.092221] x23: 0000000000000000 x22: 0000000000000000
[10.092223] x21: ffff841fb8425e18 x20: ffff801fb3a56438
[10.092226] x19: ffff801fb3a56000 x18: ffffffffffffffff
[10.092228] x17: 0000000000000000 x16: 0000000000000000
[10.092231] x15: ffff00001122d6c8 x14: ffff00009159b7b7
[10.092234] x13: ffff00001159b7c5 x12: ffff000011245000
[10.092236] x11: 0000000005f5e0ff x10: ffff00001159b750
[10.092239] x9 : 00000000ffffffd0 x8 : 0000000000000465
[10.092242] x7 : ffff0000112457f8 x6 : ffff0000113bd7ce
[10.092245] x5 : 0000000000000000 x4 : 0000000000000000
[10.092247] x3 : 00000000ffffffff x2 : ffff000011245828
[10.092250] x1 : 4b5860bd05871300 x0 : 0000000000000000
[10.092253] Call trace:
[10.092255] phy_stop+0x90/0xb0
[10.092260] hns_nic_init_phy+0xf8/0x110
[10.092262] hns_nic_try_get_ae+0x4c/0x3b0
[10.092264] hns_nic_dev_probe+0x1fc/0x480
[10.092268] platform_drv_probe+0x50/0xa0
[10.092271] really_probe+0x1f4/0x298
[10.092273] driver_probe_device+0x58/0x108
[10.092275] __driver_attach+0xdc/0xe0
[10.092278] bus_for_each_dev+0x74/0xc8
[10.092280] driver_attach+0x20/0x28
[10.092283] bus_add_driver+0x1b8/0x228
[10.092285] driver_register+0x60/0x110
[10.092288] __platform_driver_register+0x40/0x48
[10.092292] hns_nic_dev_driver_init+0x18/0x20
[10.092296] do_one_initcall+0x5c/0x180
[10.092299] kernel_init_freeable+0x198/0x240
[10.092303] kernel_init+0x10/0x108
[10.092306] ret_from_fork+0x10/0x18
[10.092308] ---[ end trace 1396dd0278e397eb ]---
This WARNING occurred because of calling phy_stop before phy_start.
The root cause of the problem in commit '308c6cafde01' is:
Reference to hns_nic_init_phy, the flag phydev->supported is changed after
phy_connect_direct. The flag phydev->supported is 0x6ff when hns modules is
loaded, so will not change Fiber Port power(Reference to marvell.c), which
is power on at default.
Then the flag phydev->supported is changed to 0x6f, so Fiber Port power is
off when removing hns modules.
When hns modules installed again, the flag phydev->supported is default
value 0x6ff, so will not change Fiber Port power(now is off), causing mac
link not up problem.
So the solution is change phy flags before phy_connect_direct.
Fixes: 308c6cafde ("net: hns: All ports can not work when insmod hns ko after rmmod.")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses GPIO descriptors only, <linux/of_gpio.h>
is not used so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 653e92a917 ("net: macb: add support for padding and fcs
computation") introduced a bug fixed by commit 899ecaedd1 ("net:
ethernet: cadence: fix socket buffer corruption problem"). Code removed
in this patch is not reachable at all so remove it.
Fixes: 653e92a917 ("net: macb: add support for padding and fcs computation")
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not use the old GPIO includes so drop
them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure chain element is updated before ringing the doorbell.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are some issues with the ucc_of_parse_tdm function:
1, a possible null pointer dereference in ucc_of_parse_tdm,
detected by the semantic patch deref_null.cocci,
with the following warning:
drivers/soc/fsl/qe/qe_tdm.c:177:21-24: ERROR: pdev is NULL but dereferenced.
2, dev gets modified, so in any case that devm_iounmap() will fail
even when the new pdev is valid, because the iomap was done with a
different pdev.
3, there is no driver bind with the "fsl,t1040-qe-si" or
"fsl,t1040-qe-siram" device. So allocating resources using devm_*()
with these devices won't provide a cleanup path for these resources
when the caller fails.
This patch fixes them.
Suggested-by: Li Yang <leoyang.li@nxp.com>
Suggested-by: Christophe LEROY <christophe.leroy@c-s.fr>
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Peng Hao <peng.hao2@zte.com.cn>
CC: Julia Lawall <julia.lawall@lip6.fr>
CC: Zhao Qiang <qiang.zhao@nxp.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: linuxppc-dev@lists.ozlabs.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two new Realtek Ethernet devices which are re-branded r8168h.
Add the IDs to to support them.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs after the call to 'pci_alloc_irq_vectors()', we must
call 'pci_free_irq_vectors()' in order to avoid a resource leak.
The same sequence is already in place in the corresponding 'cgx_remove()'
function.
Fixes: 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Several fixes here. Basically split down the line between newly
introduced regressions and long existing problems:
1) Double free in tipc_enable_bearer(), from Cong Wang.
2) Many fixes to nf_conncount, from Florian Westphal.
3) op->get_regs_len() can throw an error, check it, from Yunsheng
Lin.
4) Need to use GFP_ATOMIC in *_add_hash_mac_address() of fsl/fman
driver, from Scott Wood.
5) Inifnite loop in fib_empty_table(), from Yue Haibing.
6) Use after free in ax25_fillin_cb(), from Cong Wang.
7) Fix socket locking in nr_find_socket(), also from Cong Wang.
8) Fix WoL wakeup enable in r8169, from Heiner Kallweit.
9) On 32-bit sock->sk_stamp is not thread-safe, from Deepa Dinamani.
10) Fix ptr_ring wrap during queue swap, from Cong Wang.
11) Missing shutdown callback in hinic driver, from Xue Chaojing.
12) Need to return NULL on error from ip6_neigh_lookup(), from Stefano
Brivio.
13) BPF out of bounds speculation fixes from Daniel Borkmann"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
ipv6: Consider sk_bound_dev_if when binding a socket to an address
ipv6: Fix dump of specific table with strict checking
bpf: add various test cases to selftests
bpf: prevent out of bounds speculation on pointer arithmetic
bpf: fix check_map_access smin_value test when pointer contains offset
bpf: restrict unknown scalars of mixed signed bounds for unprivileged
bpf: restrict stack pointer arithmetic for unprivileged
bpf: restrict map value pointer arithmetic for unprivileged
bpf: enable access to ax register also from verifier rewrite
bpf: move tmp variable into ax register in interpreter
bpf: move {prev_,}insn_idx into verifier env
isdn: fix kernel-infoleak in capi_unlocked_ioctl
ipv6: route: Fix return value of ip6_neigh_lookup() on neigh_create() error
net/hamradio/6pack: use mod_timer() to rearm timers
net-next/hinic:add shutdown callback
net: hns3: call hns3_nic_net_open() while doing HNAE3_UP_CLIENT
ip: validate header length on virtual device xmit
tap: call skb_probe_transport_header after setting skb->dev
ptr_ring: wrap back ->producer in __ptr_ring_swap_queue()
net: rds: remove unnecessary NULL check
...
If there is no shutdown callback, our board will report pcie UNF errors
after restarting. This patch add shutdown callback for hinic.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HNAE3_DOWN_CLIENT calling hns3_nic_net_stop(), HNAE3_UP_CLIENT
should call hns3_nic_net_open(), since if the number of queue or
the map of TC has is changed before HHAE3_UP_CLIENT is called,
it will cause problem.
Also the HNS3_NIC_STATE_RESETTING flag needs to be cleared before
hns3_nic_net_open() called, and set it back while hns3_nic_net_open()
failed.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BPF flow dissector expects either skb->sk or skb->dev set on
all skbs. Delay flow dissection until after skb->dev is set.
This requires calling from within an rcu read-side critical section.
That is fine, see also the call from tun_xdp_one.
Fixes: d0e13a1488 ("flow_dissector: lookup netns by skb->sk if skb->dev is NULL")
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 33a48ab105 ("ibmveth: Fix DMA unmap error") fixed an issue in the
normal code path of ibmveth_xmit_start() that was originally introduced by
Commit 6e8ab30ec6 ("ibmveth: Add scatter-gather support"). This original
fix missed the error path where dma_unmap_page is wrongly called on the
header portion in descs[0] which was mapped with dma_map_single. As a
result a failure to DMA map any of the frags results in a dmesg warning
when CONFIG_DMA_API_DEBUG is enabled.
------------[ cut here ]------------
DMA-API: ibmveth 30000002: device driver frees DMA memory with wrong function
[device address=0x000000000a430000] [size=172 bytes] [mapped as page] [unmapped as single]
WARNING: CPU: 1 PID: 8426 at kernel/dma/debug.c:1085 check_unmap+0x4fc/0xe10
...
<snip>
...
DMA-API: Mapped at:
ibmveth_start_xmit+0x30c/0xb60
dev_hard_start_xmit+0x100/0x450
sch_direct_xmit+0x224/0x490
__qdisc_run+0x20c/0x980
__dev_queue_xmit+0x1bc/0xf20
This fixes the API misuse by unampping descs[0] with dma_unmap_single.
Fixes: 6e8ab30ec6 ("ibmveth: Add scatter-gather support")
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rtl8169_runtime_resume() we configure WoL but don't set the device
to wakeup-enabled. This prevents PME generation once the cable is
re-plugged. Fix this by moving the call to device_set_wakeup_enable()
to __rtl8169_set_wol().
Fixes: 433f9d0ddc ("r8169: improve saved_wolopts handling")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When x25_asy_open() fails, it already cleans up by itself,
so its caller doesn't need to free the memory again.
It seems we still have to call x25_asy_free() to clear the SLF_INUSE
bit, so just set these pointers to NULL after kfree().
Reported-and-tested-by: syzbot+5e5e969e525129229052@syzkaller.appspotmail.com
Fixes: 3b780bed31 ("x25_asy: Free x25_asy on x25_asy_open() failure.")
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big set of USB and PHY driver patches for 4.21-rc1.
All of the usual bits are in here:
- loads of USB gadget driver updates and additions
- new device ids
- phy driver updates
- xhci reworks and new features
- typec updates
Full details are in the shortlog.
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCYxNA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl4pQCfaQBjMxPpp6TVcHANZ/O+zE3NH/wAoL11p3IB
KUq8v9pmcHO8sW5TWOJw
=iYGf
-----END PGP SIGNATURE-----
Merge tag 'usb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 4.21-rc1.
All of the usual bits are in here:
- loads of USB gadget driver updates and additions
- new device ids
- phy driver updates
- xhci reworks and new features
- typec updates
Full details are in the shortlog.
All of these have been in linux-next for a long time with no reported
issues"
* tag 'usb-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (142 commits)
USB: serial: option: add Fibocom NL678 series
cdc-acm: fix abnormal DATA RX issue for Mediatek Preloader.
usb: r8a66597: Fix a possible concurrency use-after-free bug in r8a66597_endpoint_disable()
usb: typec: tcpm: Extend the matching rules on PPS APDO selection
usb: typec: Improve Alt Mode documentation
usb: musb: dsps: fix runtime pm for peripheral mode
usb: musb: dsps: fix otg state machine
USB: serial: pl2303: add ids for Hewlett-Packard HP POS pole displays
usb: renesas_usbhs: add support for RZ/G2E
usb: ehci-omap: Fix deferred probe for phy handling
usb: roles: Add a description for the class to Kconfig
usb: renesas_usbhs: mark PM functions as __maybe_unused
usb: core: Remove unnecessary memset()
usb: host: isp1362-hcd: convert to DEFINE_SHOW_ATTRIBUTE
phy: qcom-qmp: Expose provided clocks to DT
dt-bindings: phy-qcom-qmp: Move #clock-cells to child
phy: qcom-qmp: Utilize fully-specified DT registers
dt-bindings: phy-qcom-qmp: Fix register underspecification
phy: ti: fix semicolon.cocci warnings
phy: dphy: Add configuration helpers
...
This has been a fairly typical cycle, with the usual sorts of driver
updates. Several series continue to come through which improve and
modernize various parts of the core code, and we finally are starting to
get the uAPI command interface cleaned up.
- Various driver fixes for bnxt_re, cxgb3/4, hfi1, hns, i40iw, mlx4, mlx5,
qib, rxe, usnic
- Rework the entire syscall flow for uverbs to be able to run over
ioctl(). Finally getting past the historic bad choice to use write()
for command execution
- More functional coverage with the mlx5 'devx' user API
- Start of the HFI1 series for 'TID RDMA'
- SRQ support in the hns driver
- Support for new IBTA defined 2x lane widths
- A big series to consolidate all the driver function pointers into
a big struct and have drivers provide a 'static const' version of the
struct instead of open coding initialization
- New 'advise_mr' uAPI to control device caching/loading of page tables
- Support for inline data in SRPT
- Modernize how umad uses the driver core and creates cdev's and sysfs
files
- First steps toward removing 'uobject' from the view of the drivers
-----BEGIN PGP SIGNATURE-----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=T0p1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a fairly typical cycle, with the usual sorts of driver
updates. Several series continue to come through which improve and
modernize various parts of the core code, and we finally are starting
to get the uAPI command interface cleaned up.
- Various driver fixes for bnxt_re, cxgb3/4, hfi1, hns, i40iw, mlx4,
mlx5, qib, rxe, usnic
- Rework the entire syscall flow for uverbs to be able to run over
ioctl(). Finally getting past the historic bad choice to use
write() for command execution
- More functional coverage with the mlx5 'devx' user API
- Start of the HFI1 series for 'TID RDMA'
- SRQ support in the hns driver
- Support for new IBTA defined 2x lane widths
- A big series to consolidate all the driver function pointers into a
big struct and have drivers provide a 'static const' version of the
struct instead of open coding initialization
- New 'advise_mr' uAPI to control device caching/loading of page
tables
- Support for inline data in SRPT
- Modernize how umad uses the driver core and creates cdev's and
sysfs files
- First steps toward removing 'uobject' from the view of the drivers"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (193 commits)
RDMA/srpt: Use kmem_cache_free() instead of kfree()
RDMA/mlx5: Signedness bug in UVERBS_HANDLER()
IB/uverbs: Signedness bug in UVERBS_HANDLER()
IB/mlx5: Allocate the per-port Q counter shared when DEVX is supported
IB/umad: Start using dev_groups of class
IB/umad: Use class_groups and let core create class file
IB/umad: Refactor code to use cdev_device_add()
IB/umad: Avoid destroying device while it is accessed
IB/umad: Simplify and avoid dynamic allocation of class
IB/mlx5: Fix wrong error unwind
IB/mlx4: Remove set but not used variable 'pd'
RDMA/iwcm: Don't copy past the end of dev_name() string
IB/mlx5: Fix long EEH recover time with NVMe offloads
IB/mlx5: Simplify netdev unbinding
IB/core: Move query port to ioctl
RDMA/nldev: Expose port_cap_flags2
IB/core: uverbs copy to struct or zero helper
IB/rxe: Reuse code which sets port state
IB/rxe: Make counters thread safe
IB/mlx5: Use the correct commands for UMEM and UCTX allocation
...
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
