In register_netdevice(), when ndo_init() is successful and later
some error occurred, ndo_uninit() will be called.
So dummy deivce is desirable to implement ndo_uninit() method
to free percpu stats for this case.
And, ndo_uninit() is also called along with dev->destructor() when
device is unregistered, so in order to prevent dev->dstats from
being freed twice, dev->destructor is modified to free_netdev().
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make smsc75xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1492 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f793.
Tested on ARM/Omap3 with EVB-LAN7500-LC.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A parameter set exists for WRED mode, called wred_set, to hold the same
values for qavg and qidlestart across all VQs. The WRED mode values had
been previously held in the VQ for the default DP. After these values
were moved to wred_set, the VQ for the default DP was no longer created
automatically (so that it could be omitted on purpose, to have packets
in the default DP enqueued directly to the device without using RED).
However, gred_dump() was overlooked during that change; in WRED mode it
still reads qavg/qidlestart from the VQ for the default DP, which might
not even exist. As a result, this command sequence will cause an oops:
tc qdisc add dev $DEV handle $HANDLE parent $PARENT gred setup \
DPs 3 default 2 grio
tc qdisc change dev $DEV handle $HANDLE gred DP 0 prio 8 $RED_OPTIONS
tc qdisc change dev $DEV handle $HANDLE gred DP 1 prio 8 $RED_OPTIONS
This fixes gred_dump() in WRED mode to use the values held in wred_set.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some virtio fixes for 3.4:
a test build fix, a patch by Ren fixing naming for systems with a massive
number of virtio blk devices, and balloon fixes for powerpc
by David Gibson.
There was some discussion about Ren's patch for virtio disc naming: some people
wanted to move the legacy name mangling function to the block core. But
there's no concensus on that yet, and we can always deduplicate later.
Added comments in the hope that this will stop people from
copying this legacy naming scheme into future drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPio1GAAoJECgfDbjSjVRpGDAH/3C/bXm9mriuNauRHwktHgJe
gmh2BfUgnxly6vheuz0Fv61lTe6V8kekHVolbUYwAUgXeWEKK1C59xehrMGRIPDG
1XUiti50U3P+skhIfrbkS5nZ7L+5Hk0ToQ6dd9v0BM2GxDOvgwidlY1bZe+wJEZf
Lvl6w/djBCr1e3k4qfRnpTcdJJ4FnOjGbikLQhSTGfUXeNo6uWS1hljYWnAhzFkd
1xU8h5PP0TDR0nYb80CeB+9Lxw0w4qyNPJIBhNN6ucB/1U6R+55HpEpmrLUkn910
sEFEFsc0cRVWr8FiOTlmzxLHnwTc8AY/Bsp9TMSmnTRu3ZQcoQMTQQCczRj04xI=
=VmpJ
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael S. Tsirkin:
"Here are some virtio fixes for 3.4: a test build fix, a patch by Ren
fixing naming for systems with a massive number of virtio blk devices,
and balloon fixes for powerpc by David Gibson.
There was some discussion about Ren's patch for virtio disc naming:
some people wanted to move the legacy name mangling function to the
block core. But there's no concensus on that yet, and we can always
deduplicate later. Added comments in the hope that this will stop
people from copying this legacy naming scheme into future drivers."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: fix handling of PAGE_SIZE != 4k
virtio_balloon: Fix endian bug
virtio_blk: helper function to format disk names
tools/virtio: fix up vhost/test module build
Some shortcomings introduced into pci_restore_state() by commit
26f41062f2 ("PCI: check for pci bar restore completion and retry")
have been fixed by recent commit ebfc5b802f ("PCI: Fix regression in
pci_restore_state(), v3"), but that commit treats all PCI devices as
those with Type 0 configuration headers.
That is not entirely correct, because Type 1 and Type 2 headers have
different layouts. In particular, the area occupied by BARs in Type 0
config headers contains the secondary status register in Type 1 ones and
it doesn't make sense to retry the restoration of that register even if
the value read back from it after a write is not the same as the written
one (it very well may be different).
For this reason, make pci_restore_state() only retry the restoration
of BARs for Type 0 config headers. This effectively makes it behave
as before commit 26f41062f2 for all header types except for Type 0.
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm dropping off as Documentation/ maintainer.
Rob Landley has agreed to take it over. Thanks, Rob.
I'll still be around reviewing patches and testing.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michel Lespinasse cleaned up the futex calling conventions in commit
37a9d912b2 ("futex: Sanitize cmpxchg_futex_value_locked API").
But the ia64 implementation was subtly broken. Gcc does not know that
register "r8" will be updated by the fault handler if the cmpxchg
instruction takes an exception. So it feels safe in letting the
initialization of r8 slide to after the cmpxchg. Result: we always
return 0 whether the user address faulted or not.
Fix by moving the initialization of r8 into the __asm__ code so gcc
won't move it.
Reported-by: <emeric.maschino@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42757
Tested-by: <emeric.maschino@gmail.com>
Acked-by: Michel Lespinasse <walken@google.com>
Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Starting from 7e16838d "i387: support lazy restore of FPU state"
we assume that fpu_owner_task doesn't need restore_fpu_checking()
on the context switch, its FPU state should match what we already
have in the FPU on this CPU.
However, debugger can change the tracee's FPU state, in this case
we should reset fpu.last_cpu to ensure fpu_lazy_restore() can't
return true.
Change init_fpu() to do this, it is called by user_regset->set()
methods.
Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20120416204815.GB24884@redhat.com
Cc: <stable@vger.kernel.org> v3.3
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Commit 26092bf5 broke handling of journalled quota mount options by
trying to parse argument of every mount option as a number. Fix this
by dealing with the quota options before we call match_int().
Thanks to Jan Kara for discovering this regression.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Left-overs for an earlier iteration of the generic clock events patch removed.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert the --strict test for the old preferred block
comment style in drivers/net and net/
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If either call to pcan_usb_pro_send_req() in
drivers/net/can/usb/peak_usb/pcan_usb_pro.c::pcan_usb_pro_init()
fails, we'll leak the memory we allocated to 'usb_if' with kzalloc()
when the 'usb_if' variable goes out of scope without having been
assigned to anything as we 'return err;'.
Fix this by adding appropriate kfree(usb_if) calls to the error paths.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The combination of commit 1b1247dd75
"mfd: Add support for RICOH PMIC RC5T583"
and commit 6ffc327021
"regulator: Add support for RICOH PMIC RC5T583 regulator"
are causing the i386 allmodconfig builds to fail with this:
ERROR: "rc5t583_update" [drivers/regulator/rc5t583-regulator.ko] undefined!
ERROR: "rc5t583_set_bits" [drivers/regulator/rc5t583-regulator.ko] undefined!
ERROR: "rc5t583_clear_bits" [drivers/regulator/rc5t583-regulator.ko] undefined!
ERROR: "rc5t583_read" [drivers/regulator/rc5t583-regulator.ko] undefined!
and this:
ERROR: "rc5t583_ext_power_req_config" [drivers/regulator/rc5t583-regulator.ko] undefined!
For the 1st four, make the simple ops static inline, instead of
polluting the namespace with trivial exports. For the last one,
add an EXPORT_SYMBOL.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cld.h file contains the definition of the upcall format to talk
with nfsdcld. When I added the file though, I neglected to add it
to the headers-y target, so make headers_install wasn't installing it.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
It's only called from amd.c:srat_detect_node(). The introduced
condition for calling the fixup code is true for all AMD
multi-node processors, e.g. Magny-Cours and Interlagos. There we
have 2 NUMA nodes on one socket. Thus there are cores having
different numa-node-id but with equal phys_proc_id.
There is no point to print error messages in such a situation.
The confusing/misleading error message was introduced with
commit 64be4c1c24 ("x86: Add
x86_init platform override to fix up NUMA core numbering").
Remove the default fixup function (especially the error message)
and replace it by a NULL pointer check, move the
Numascale-specific condition for calling the fixup into the
fixup-function itself and slightly adapt the comment.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: <stable@kernel.org>
Cc: <sp@numascale.com>
Cc: <bp@amd64.org>
Cc: <daniel@numascale-asia.com>
Link: http://lkml.kernel.org/r/20120402160648.GR27684@alberich.amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The method used to work out whether we were booted by EFI firmware or
via a boot loader is broken. Because efi_main() is always executed
when booting from a boot loader we will dereference invalid pointers
either on the stack (CONFIG_X86_32) or contained in %rdx
(CONFIG_X86_64) when searching for an EFI System Table signature.
Instead of dereferencing these invalid system table pointers, add a
new entry point that is only used when booting from EFI firmware, when
we know the pointer arguments will be valid. With this change legacy
boot loaders will no longer execute efi_main(), but will instead skip
EFI stub initialisation completely.
[ hpa: Marking this for urgent/stable since it is a regression when
the option is enabled; without the option the patch has no effect ]
Signed-off-by: Matt Fleming <matt.hfleming@intel.com>
Link: http://lkml.kernel.org/r/1334584744.26997.14.camel@mfleming-mobl1.ger.corp.intel.com
Reported-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> v3.3
Upon lastclose(), we switch back to the fbcon configuration. This
requires taking the mode_config lock in order to serialise the change
with output probing elsewhere.
Reported-by: Oleksij Rempel <bug-track@fisher-privat.net>
References: https://bugs.freedesktop.org/show_bug.cgi?id=48652
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
bcma should check for a fallback sprom every time it can not find a
sprom on the card itself or a normal external sprom mapped into the
memory of the chip. When otp sprom support was introduced it tried to
read out the sprom from the wireless chip also if no otp sprom was
available. This caused a Data bus error in bcma_sprom_get() when
reading out the sprom for the SoC.
This fixes a regression introduced in commit:
commit 10d8493cd9
Author: Arend van Spriel <arend@broadcom.com>
Date: Tue Mar 6 15:50:48 2012 +0100
bcma: add support for on-chip OTP memory used for SPROM storage
This patch was tested on a Netgear WNDR3400 (Broadcom BCM4718 SoC).
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assumption that irq numbers of asic3 gpios start at
IRQ_BOARD_START is certainly wrong - driver may as well
use any other base for its irqs (consider for example
the imaginary case of two ASIC3 chips onboard)
Furthermore, some platforms even don't have IRQ_BOARD_START
defined, so driver will fail to build on them:
-------------------------------------------------------
drivers/mfd/asic3.c: In function 'asic3_gpio_to_irq':
drivers/mfd/asic3.c:530: error: 'IRQ_BOARD_START' undeclared (first use in this function)
drivers/mfd/asic3.c:530: error: (Each undeclared identifier is reported only once
drivers/mfd/asic3.c:530: error: for each function it appears in.)
-------------------------------------------------------
Fix it by using irq_base from driver data.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is observed that the echi ports of 3430 sdp board
are not working due to the random timing of programming
the associated GPIOs of the ULPI PHYs of the EHCI for reset.
If the PHYs are reset at during usbhs core driver, host ports will
not work because EHCI driver is loaded after the resetting PHYs.
The PHYs should be in reset state while initializing the EHCI
controller.
The code which does the GPIO pins associated with the PHYs
are programmed to reset is moved from the USB host core driver
to EHCI driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Andi Kleen and Tim Chen have reported that under certain circumstances
the extent cache statistics are causing scalability problems due to
cache line bounces.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
Here are the fixes I have queued for v3.4-rc cycle so far.
It includes fixes on many of the gadget drivers and a few
of the UDC controller drivers.
For musb we have a fix for a kernel oops when unloading
omap2430.ko glue layer, proper error checking for pm_runtime_*,
fix for the ULPI transfer block, and a bug fix in musb_cleanup_urb
routine.
For s3c-hsotg we have mostly FIFO-related fixes (proper TX FIFO
allocation, TX FIFO corruption fix in DMA mode) but also a couple
of minor fixes (fixing maximum packet size for ep0 and fix for
big transfers with DMA).
For the dwc3 driver we have a memory leak fix, a very important
fix for USB30CV with SetFeature tests and the hability to handle
ep0 requests bigger than wMaxPacketSize.
On top of that there's a bunch of gadget driver minor fixes adding
proper section annotations, and fixing up the sysfs interface for
doing device-initiated connect/disconnect and so on.
All patches have been pending on the mailing list for quite a while
and look good for your for-linus branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Wqlb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.4-rc cycle
Here are the fixes I have queued for v3.4-rc cycle so far.
It includes fixes on many of the gadget drivers and a few
of the UDC controller drivers.
For musb we have a fix for a kernel oops when unloading
omap2430.ko glue layer, proper error checking for pm_runtime_*,
fix for the ULPI transfer block, and a bug fix in musb_cleanup_urb
routine.
For s3c-hsotg we have mostly FIFO-related fixes (proper TX FIFO
allocation, TX FIFO corruption fix in DMA mode) but also a couple
of minor fixes (fixing maximum packet size for ep0 and fix for
big transfers with DMA).
For the dwc3 driver we have a memory leak fix, a very important
fix for USB30CV with SetFeature tests and the hability to handle
ep0 requests bigger than wMaxPacketSize.
On top of that there's a bunch of gadget driver minor fixes adding
proper section annotations, and fixing up the sysfs interface for
doing device-initiated connect/disconnect and so on.
All patches have been pending on the mailing list for quite a while
and look good for your for-linus branch.
Complete the separation of the twl6040 from the twl core since
it is a separate chip, not part of the twl6030 PMIC.
Make the needed Kconfig changes for the depending drivers at the
same time to avoid breaking the kernel build (vibra, ASoC components).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The ux500 default config enables the db5500 and the db8500.
The incoming cpuidle driver uses the 'prcmu_enable_wakeups'
and the 'prcmu_set_power_state' functions but these ones
are defined but not implemented for the db5500, leading to
an unresolved symbol error at link time. In order to compile,
we have to disable the db5500 support which is not acceptable
for the default config.
I noticed there are also some other functions which are
defined but not implemented.
This patch fix this by removing the functions definitions
and move out of the config section the empty functions which
are normally used when the DB550 config is disabled.
Only the functions which are not implemented are concerned
by this modification.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Forget to unreserve after pinning. This can lead to problems in
soft reset and resume.
v2: rework patch as per Michel's suggestion.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My rv515 card is very flaky with msi enabled. Every so often it loses a rearm
and never comes back, manually banging the rearm brings it back.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
You need to setup the dm9000 irq via gpio_to_irq() since
d0fbda9add (ARM: at91/gpio: drop PIN_BASE).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> [3.2+]
The real function is long gone and the empty one will generate warnings
when configured without Atmel serial:
arch/arm/mach-at91/at91rm9200_devices.c:1176: warning: 'struct at91_uart_config' declared inside parameter list
arch/arm/mach-at91/at91rm9200_devices.c:1176: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
at91_matrix_* macro's are used by at91_udc usb gadget driver,
which can be built as module, therefore we need to export the
variable containing matrix base address.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After commit b55149529d (ARM: at91/PMC: make register base soc independent)
building atmel_usba_udc as a module fails with following message
ERROR: "at91_pmc_base" [drivers/usb/gadget/atmel_usba_udc.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Export symbol to allow driver to be built as a module again.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After commit f363c40 (ARM: at91: make sdram/ddr register base soc independent)
building at91_cf as a module fails with:
ERROR: "at91_ramc_base" [drivers/pcmcia/at91_cf.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Export at91_ramc_base symbol to allow drivers using at91_ramc_*
functions to be built as modules again.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
[nicolas.ferre@atmel.com: modify slightly commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After commit 5e9cf5e (ARM: at91: make ST (System Timer) soc independent)
building at91rm9200_wdt as a module fails with following message
ERROR: "at91_st_base" [drivers/watchdog/at91rm9200_wdt.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Export symbol to allow wdt driver to be built as a module again.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
[nicolas.ferre@atmel.com: use EXPORT_SYMBOL_GPL()]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This regression has been introduced in
commit ca9bfa7eed
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat Jan 28 14:49:20 2012 +0100
drm/i915: fixup interlaced vertical timings confusion, part 1
Unfortunately that commit failed to take into account that the lvds
code does some special adjustements to the crtc timings for upscaling
an centering.
Fix this by explicitly computing crtc timings in the lvds mode fixup
function and setting a special flag in mode->private_flags if the crtc
timings have been adjusted.
v2: Add a comment to explain the new mode driver private flag,
suggested by Eugeni Dodonov.
v3: Kill the confusing and now redundant set_crtcinfo call in
intel_fixed_panel_mode, noticed by Chris Wilson.
Reported-and-Tested-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43071
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some new drivers and changed Kconfig dependencies for the v3.4
kernel affecting the U8500 defconfig:
- The SOC config options are now brought in by default
- No need to explicitly select misc devices anymore
- I2C is selected by default
- We now have support for charging from the AB8500 so compile
in this
- The regulator framework needs to be explictly selected
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A recent change to a Kconfig configuration saw MACH_U8500
remove TPS6105X selection. In doing so Kconfig stopped
selecting REGULATORS, which is still required. This patch
sees UX500_SOC_DB8500 explicitly select it instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This can happen if the instruction is much longer than the maximum length,
or if insn->opnd_bytes is manually changed.
This patch also fixes warnings from -Wswitch-default flag.
Reported-by: Prashanth Nageshappa <prashanth@linux.vnet.ibm.com>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Jim Keniston <jkenisto@linux.vnet.ibm.com>
Cc: Linux-mm <linux-mm@kvack.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Anton Arapov <anton@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20120413032427.32577.42602.stgit@localhost.localdomain
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The 68EZ328/bootlogo.h is not actually used in the 68EZ328 platform code
at all. It is used by the 68VZ328 platform code though, so move it to be
with the rest of the 68VZ328 platform code.
Commit c0e0c89c08 ("fix broken boot logo
inclusion") modified the bootlogo code to not be included in asm code.
Modify 68VZ328/bootlogo.h so that the bootlogo bit map is named correctly
for direct use in the C code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The 68EZ328 and 68VZ328 platforms currently try to process their bootlogo.h
to make it clean to include in asm files. This is no longer used, the
bootlogo.h file is now included only in C code, so remove all the processing
code in the 68EZ328 and 68VZ328 Makefiles.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Pull ARM fixes from Russell King:
"Nothing too disasterous, the biggest thing being the removal of the
regulator support for vcore in the AMBA driver; only one SoC was using
this and it got broken during the last merge window, which then
started causing problems for other people. Mutual agreement was
reached for it to be removed."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
ARM: 7383/1: nommu: populate vectors page from paging_init
ARM: 7381/1: nommu: fix typo in mm/Kconfig
ARM: 7380/1: DT: do not add a zero-sized memory property
ARM: 7379/1: DT: fix atags_to_fdt() second call site
ARM: 7366/3: amba: Remove AMBA level regulator support
ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented
The 'max' range needs to be unsigned, since the size of the user address
space is bigger than 2GB.
We know that 'count' is positive in 'long' (that is checked in the
caller), so we will truncate 'max' down to something that fits in a
signed long, but before we actually do that, that comparison needs to be
done in unsigned.
Bug introduced in commit 92ae03f2ef ("x86: merge 32/64-bit versions of
'strncpy_from_user()' and speed it up"). On x86-64 you can't trigger
this, since the user address space is much smaller than 63 bits, and on
x86-32 it works in practice, since you would seldom hit the strncpy
limits anyway.
I had actually tested the corner-cases, I had only tested them on
x86-64. Besides, I had only worried about the case of a pointer *close*
to the end of the address space, rather than really far away from it ;)
This also changes the "we hit the user-specified maximum" to return
'res', for the trivial reason that gcc seems to generate better code
that way. 'res' and 'count' are the same in that case, so it really
doesn't matter which one we return.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
c5905afb0 ("static keys: Introduce 'struct static_key'...") renamed
struct jump_label_key to struct static_key. Fixup ARM for this to
eliminate these build warnings:
include/linux/jump_label.h:113:2:
warning: passing argument 1 of 'arch_static_branch' from incompatible pointer type
include/asm/jump_label.h:17:82:
note: expected 'struct jump_label_key *' but argument is of type 'struct static_key *'
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently when ThumbEE is not enabled (!CONFIG_ARM_THUMBEE) the ThumbEE
register states are not saved/restored at context switch. The default state
of the ThumbEE Ctrl register (TEECR) allows userspace accesses to the
ThumbEE Base Handler register (TEEHBR). This can cause unexpected behaviour
when people use ThumbEE on !CONFIG_ARM_THUMBEE kernels, as well as allowing
covert communication - eg between userspace tasks running inside chroot
jails.
This patch sets up TEECR in order to prevent user-space access to TEEHBR
when !CONFIG_ARM_THUMBEE. In this case, tasks are sent SIGILL if they try to
access TEEHBR.
Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a bank of memory spanning the 4GB boundary is added on a !CONFIG_LPAE
kernel then we will hang early during boot since the memory bank will
have wrapped around to zero.
This patch truncates memory banks for !LPAE configurations when the end
address is not representable in 32 bits.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During booting of cpu1, there is a short window where cpu1
is online, but not active where cpu1 is occupied by waiting
to become active. If cpu0 then decides to schedule something
on cpu1 and wait for it to complete, before cpu0 has set
cpu1 active, we have a deadlock.
Typically it's this CPU frequency transition that happens at
this time, so let's just not wait for it to happen, it will
happen whenever the CPU eventually comes online instead.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
