Extend the tryacpi module parameter to turn off acpi_ipmi_probe such
that hard-coded options (type, ports, address, etc.) have complete
control over the smi_info data structures setup by the driver.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Under some circumstances, the IPMI state machine could return
a call without delay option but the driver would still do a long
delay because the result wasn't checked. Instead of calling
the state machine after transaction done, just go back to the
top of the processing to start over.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Enclosing '#include <linux/acpi.h>' within '#ifdef CONFIG_ACPI' is
unnecessary, since it has its own conditional compile for CONFIG_ACPI.
Commit 0fbcf4af7c ("ipmi: Convert the IPMI SI ACPI handling to a
platform device") exposed this as a problem for platforms that do not
support ACPI when it introduced a call to ACPI_PTR() macro outside of
the CONFIG_ACPI conditional compile. This would have been perfectly
acceptable if acpi.h were not conditionally excluded for the non-acpi
platform, because the conditional compile within acpi.h defines
ACPI_PTR() to return NULL when compiled for non acpi platforms.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Fixed commit reference in header to conform to standard.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We call cleanup_one_si from ipmi_pci_remove, which calls ->addr_source_cleanup,
which gets set to point to ipmi_pci_cleanup, which does a pci_disable_device.
On return from this, we do a second pci_disable_device, which
results in the trace below.
ipmi_si 0000:00:16.0: disabling already-disabled device
Call Trace:
[<ffffffff818ce54c>] dump_stack+0x45/0x57
[<ffffffff810525f7>] warn_slowpath_common+0x97/0xe0
[<ffffffff810526f6>] warn_slowpath_fmt+0x46/0x50
[<ffffffff81497ca1>] pci_disable_device+0xb1/0xc0
[<ffffffffa00851a5>] ipmi_pci_remove+0x25/0x30 [ipmi_si]
[<ffffffff8149a696>] pci_device_remove+0x46/0xc0
[<ffffffff8156801f>] __device_release_driver+0x7f/0xf0
[<ffffffff81568978>] driver_detach+0xb8/0xc0
[<ffffffff81567e50>] bus_remove_driver+0x50/0xa0
[<ffffffff8156914e>] driver_unregister+0x2e/0x60
[<ffffffff8149a3e5>] pci_unregister_driver+0x25/0x90
[<ffffffffa0085804>] cleanup_ipmi_si+0xd4/0xf0 [ipmi_si]
[<ffffffff810c727a>] SyS_delete_module+0x12a/0x200
[<ffffffff818d4d72>] system_call_fastpath+0x12/0x17
Signed-off-by: Dave Jones <dsj@fb.com>
Lots of char arrays could be set as const since they contain only literal
char arrays.
We could in the same time make const some struct members who are pointer
to those const char arrays.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We encountered a panic on boot in ipmi_si on a dell per320 due to an
uninitialized timer as follows.
static int smi_start_processing(void *send_info,
ipmi_smi_t intf)
{
/* Try to claim any interrupts. */
if (new_smi->irq_setup)
new_smi->irq_setup(new_smi);
--> IRQ arrives here and irq handler tries to modify uninitialized timer
which triggers BUG_ON(!timer->function) in __mod_timer().
Call Trace:
<IRQ>
[<ffffffffa0532617>] start_new_msg+0x47/0x80 [ipmi_si]
[<ffffffffa053269e>] start_check_enables+0x4e/0x60 [ipmi_si]
[<ffffffffa0532bd8>] smi_event_handler+0x1e8/0x640 [ipmi_si]
[<ffffffff810f5584>] ? __rcu_process_callbacks+0x54/0x350
[<ffffffffa053327c>] si_irq_handler+0x3c/0x60 [ipmi_si]
[<ffffffff810efaf0>] handle_IRQ_event+0x60/0x170
[<ffffffff810f245e>] handle_edge_irq+0xde/0x180
[<ffffffff8100fc59>] handle_irq+0x49/0xa0
[<ffffffff8154643c>] do_IRQ+0x6c/0xf0
[<ffffffff8100ba53>] ret_from_intr+0x0/0x11
/* Set up the timer that drives the interface. */
setup_timer(&new_smi->si_timer, smi_timeout, (long)new_smi);
The following patch fixes the problem.
To: Openipmi-developer@lists.sourceforge.net
To: Corey Minyard <minyard@acm.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # Applies cleanly to 3.10-, needs small rework before
In order to allow panic actions to be processed, the ipmi watchdog
driver sets a new timeout value on panic. The 255s timeout
was designed to allow kdump and others actions on panic, as in
http://lkml.iu.edu/hypermail/linux/kernel/0711.3/0258.html
This is counter-intuitive for a end-user who sets watchdog timeout
value to something like 30s and who expects BMC to reset the system
within 30s of a panic.
This commit allows user to configure the timeout on panic.
Signed-off-by: Jean-Yves Faye <jean-yves.faye@c-s.fr>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The policy for drivers is to have MODULE_DEVICE_TABLE() just after the
struct used in it. For clarity.
Suggested-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The IPMI driver would let the final timeout just happen, but it could
easily just stop the timer. If the timer stop fails that's ok, that
should be rare.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The timer and thread were not being started for internal messages,
so in interrupt mode if something hung the timer would never go
off and clean things up. Factor out the internal message sending
and start the timer for those messages, too.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Gouji, Masayuki <gouji.masayuki@jp.fujitsu.com>
Cc: stable@vger.kernel.org
This patch replaces timeval with timespec64 as 32 bit 'struct timeval'
will not give current time beyond 2038.
The patch changes the code to use ktime_get_real_ts64() which returns
a 'struct timespec64' instead of do_gettimeofday() which returns a
'struct timeval'
This patch also alters the format string in pr_info() for now.tv_sec
to incorporate 'long long' on 32 bit architectures.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are broken on some platforms, this gives people a chance to work
around it until the firmware is fixed.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Fix autoloading ipmi modules when using device tree.
Signed-off-by: Brijesh Singh <brijeshkumar.singh@amd.com>
Moved this change up into the CONFIG_OF section to account
for changes to the probing code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
It appears that some BMCs support interrupts but don't support setting
the irq enable bits. The interrupts are just always on. Sigh.
Add code to compensate.
The new code was very similar to another functions, so this also
factors out the common code into other functions.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Henrik Korkuc <henrik@kirneh.eu>
Received handlers defined as ipmi_recv_hndl member of struct
ipmi_user_hndl can take a spinlock. This means that if the kernel
panics while holding the lock, a deadlock may happen on the lock
while flushing queued messages in the panic context.
Calling the receive handler doesn't make much meanings in the panic
context, simply skip it to avoid possible deadlocks.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
When processing queued messages in the panic context, IPMI driver
tries to do it without any locking to avoid deadlocks. However,
this means we can touch a corrupted list if the kernel panicked
while manipulating the list. Fortunately, current `add-tail and
del-from-head' style implementation won't touch the corrupted part,
but it is inherently risky.
To get rid of the risk, this patch re-initializes the message lists
on panic if the related spinlock has already been acquired. As the
result, we may lose queued messages, but it's not so painful.
Dropping messages on the received message list is also less
problematic because no one can respond the received messages.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Fixed a comment typo.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
When flushing queued messages in run-to-completion mode,
smi_event_handler() is recursively called.
flush_messages()
smi_event_handler()
handle_transaction_done()
deliver_recv_msg()
ipmi_smi_msg_received()
smi_recv_tasklet()
sender()
flush_messages()
smi_event_handler()
...
The depth of the recursive call depends on the number of queued
messages, so it can cause a stack overflow if many messages have
been queued.
To solve this problem, this patch removes flush_messages()
from sender()@ipmi_si_intf.c. Instead, add flush_messages() to
caller side of sender() if needed. Additionally, to implement this,
add new handler flush_messages to struct ipmi_smi_handlers.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Fixed up a comment and some spacing issues.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Factor out message flushing procedure which is used in run-to-completion
mode. This patch doesn't change the logic.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
send_panic_events() calls intf->handlers->set_run_to_completion(),
but it has already been done in the caller function panic_event().
Remove it from send_panic_events().
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Constify the ACPI device ID array, it doesn't need to be writable at
runtime.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The cleanup_one_si() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This removes the no longer required setting of the module owner
for the plaform structure,powernv_ipmi_driver to THIS_MODULE as
the driver core for ipmi drivers will directly find and
set the module owner for this driver.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
If the OPAL call to receive the ipmi message fails, then we free up the
smi message and return. But, the driver still holds the reference to
old smi message in the 'cur_msg' which can potentially be accessed later
and freed again leading to kernel oops. To fix it up,
The kernel driver should reset the 'cur_msg' and send reply to the user
in addition to freeing the message.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Fixed a checkpatch warning dealing with an else after a return.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The IPMI SI driver was using direct PNP, but that was not really
ideal because the IPMI device is a platform device. There was
some special handling in the acpi_pnp.c code for making this work,
but that was breaking ACPI handling for the IPMI SSIF driver.
So without this patch there were significant issues getting the
SSIF driver to work with ACPI.
So use a platform device for ACPI detection and remove the
entry from acpi_pnp.c.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Convert the opal ipmi driver to use the new irq interface for events.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Acked-by: Corey Minyard <cminyard@mvista.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: openipmi-developer@lists.sourceforge.net
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lots of little fixes for multi-part messages:
The values was not being re-initialized, if something went wrong
handling a multi-part message and it got left in a bad state, it
might be an issue.
The commands were not correct when issuing multi-part reads, the
code was not passing in the proper value for commands. Also clean
up some minor formatting issues.
Get the block number from the right location, limit the maximum send
message size to 63 bytes and explain why, and fix some minor sylistic
issues.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The SSIF interface can optionally have an SMBus alert come in when
data is ready. Unfortunately, the IPMI spec gives wiggle room to
the implementer to allow them to always have the alert enabled,
even if the driver doesn't enable it. So implement alerts.
If you don't in this situation, the SMBus alert handling will
constantly complain.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
start_next_msg() issues a message placed in smi_info->waiting_msg
if it is non-NULL. However, sender() sets a message to
smi_info->curr_msg and NULL to smi_info->waiting_msg in the context
of run_to_completion mode. As the result, it leads an infinite
loop by waiting the completion of unissued message when leaving
dying message after kernel panic.
sender() should set the message to smi_info->waiting_msg not
curr_msg.
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
When probing an ACPI table, report a specific error, instead of just
returning an error, if _IFT doesn't exist.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
commit d6c5dc18d8 ("ipmi: Remove uses of return value of seq_printf")
incorrectly changed the return value of various proc_show functions
to use seq_has_overflowed().
These functions should return 0 on completion rather than 1/true
on overflow. 1 is the same as #define SEQ_SKIP which would cause
the output to not be emitted (skipped) instead.
This is a logical defect only as the length of these outputs are
all smaller than the initial allocation done by the seq filesystem.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Some of the adapters have spaces in their names, but that's really
hard to pass in as a module or kernel parameters. So ignore the
spaces.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog below.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IMEACgkQMUfUDdst+yloDQCfbyIRL23WVAn9ckQse/y8gbjB
OT4AoKTJbwndDP9Kb/lrj2tjd9QjNVrC
=xhen
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog.
All of this has been in linux-next for a while"
* tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (133 commits)
mei: trace: remove unused TRACE_SYSTEM_STRING
DTS: ARM: OMAP3-N900: Add lis3lv02d support
Documentation: DT: lis302: update wakeup binding
lis3lv02d: DT: add wakeup unit 2 and wakeup threshold
lis3lv02d: DT: use s32 to support negative values
Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX case
Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages case
mei: replace check for connection instead of transitioning
mei: use mei_cl_is_connected consistently
mei: fix mei_poll operation
hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg()
Drivers: hv: hv_balloon: survive ballooning request with num_pages=0
Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor function
Drivers: hv: hv_balloon: do not online pages in offline blocks
hv: remove the per-channel workqueue
hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind()
hv: run non-blocking message handlers in the dispatch tasklet
coresight: moving to new "hwtracing" directory
coresight-tmc: Adding a status interface to sysfs
coresight: remove the unnecessary configuration coresight-default-sink
...
The code was using an normal completion, but that caused stuck
task errors after a while. Use an interruptible one to avoid that.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
If ipmi_powernv_recv(...) is called without a current message it
prints a warning and returns. However it fails to release the message
lock causing the system to dead lock during any subsequent IPMI
operations.
This error path should never normally be taken unless there are bugs
elsewhere in the system.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Some BMCs don't let you clear the receive irq bit in the global
enables. This is kind of silly, but they give an error if you
try to clear it. Compensate for this by detecting the situation
and working around it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Thomas D <whissi@whissi.de>
Reviewed-by: Thomas D <whissi@whissi.de>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From a locking point of view it is safe to check waiting_msg without
a lock, but there is a memory ordering issue that causes it to
possibly not be set right when viewed from another processor. We are
already claiming a lock right after that, move the check to inside
the lock to enforce the memory ordering.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The seq_printf like functions will soon be changed to return void.
Convert these uses to check seq_has_overflowed instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Instead of manual calls of device_create_file() and
device_remove_file(), implement the condition in is_visible callback
for the attribute group and put these entries to the group, too.
This simplifies the code and avoids the possible races.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This adds a loop through the elements in the linked list, recv_msgs using
list_for_entry_safe in order to free messages in this list. In addition
we are using the safe version of this marco in order to prevent use after
bugs related to deleting the element we are on currently by holding a
pointer to the next element after the current one we are on and freeing
with the function, ipmi_free_recv_msg internally in this loop.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
A new harmless warning has come up on ARM builds with gcc-4.9:
drivers/char/ipmi/ipmi_msghandler.c: In function 'smi_send.isra.11':
include/linux/spinlock.h:372:95: warning: 'flags' may be used uninitialized in this function [-Wmaybe-uninitialized]
raw_spin_unlock_irqrestore(&lock->rlock, flags);
^
drivers/char/ipmi/ipmi_msghandler.c:1490:16: note: 'flags' was declared here
unsigned long flags;
^
This could be worked around by initializing the 'flags' variable, but it
seems better to rework the code to avoid this.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7ea0ed2b5b ("ipmi: Make the message handler easier to use for SMI interfaces")
Signed-off-by: Corey Minyard <cminyard@mvista.com>
As part of the internal y2038 cleanup, this patch removes
timespec usage in the ipmi driver, replacing it timespec64
Cc: openipmi-developer@lists.sourceforge.net
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Corey Minyard <minyard@mvista.com>
The driver uses #ifdef DEBUG_TIMING in order to conditionally print out
timestamped debug messages. Unfortunately it adds the ifdefs all over the
usage sites.
This patch cleans it up by adding a debug_timestamp() function which
is compiled out if DEBUG_TIMING isn't present. This cleans up all
the ugly ifdefs in the function logic.
Cc: openipmi-developer@lists.sourceforge.net
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Corey Minyard <minyard@mvista.com>
Removes a no longer needed FIXME comment in the function,acpi_gpe_irq_setup
for the file,ipmi_si_intf.c. This comment is no longer needed as clearly we
are passing the correct level of ACPI_GPE_LEVEL_TRIGGERED to the installer
function,acpi_install_gpe_handler due to no breakage after years of using
this ACPI level in the function,acpi_install_gpe_handler.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit or error. This is obsolete meanwhile, the core will do it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
There can't be more than a few IPMI messages allocated at any one time,
so converting the messages to slabs would be a waste. So just remove
the FIXME.
Suggested-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The previous cleanup of BMC attributes left a few holes, and if
you run with lockdep debugging with a BMC with the proper attributes,
you could get a warning.
This patch removes all the unused attributes from the BMC structure,
since they are all declared in the .data section now. It makes
the attributes all static. It fixes the referencing of the
attributes in a couple of cases that dynamically added the files
depending on BMC information.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Huang Ying <ying.huang@intel.com>
Tested-by: Alexei Starovoitov <ast@plumgrid.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
On a reset, the BMC may reset the BT enable in the processor
registers (different than the global enables in the BMC). Check
it periodically and fix it if necessary.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Tony Rex <tony.rex@ericsson.com>
Tested-by: Magnus Johansson E <magnus.e.johansson@ericsson.com>
If an attention came in while handling a message response, it
could cause the state machine to go into the wrong mode and lock
things up if the state machine wasn't in normal mode. So if the
state machine is not in normal mode, save the attention flag for
later.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Tony Rex <tony.rex@ericsson.com>
Tested-by: Magnus Johansson E <magnus.e.johansson@ericsson.com>
Cc: Per Fogelström <per.fogelstrom@ericsson.com>
The BMC can be reset while we are running; that means the interrupt
and event message buffer settings may be wrong. So periodically
check to see if these values are correct, and fix them if they
are wrong.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Tony Rex <tony.rex@ericsson.com>
Tested-by: Magnus Johansson E <magnus.e.johansson@ericsson.com>
This change adds an initial IPMI driver for powerpc OPAL firmware. The
interface is exposed entirely through firmware: we have two functions to
send and receive IPMI messages, and an interrupt notification from the
firmware to signify that a message is available.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
A message queue was added to the message handler, so the SMI
interfaces only need to handle one message at a time. Pull out
the message queue. This also leads to some significant
simplification in the shutdown of an interface, since the
message handler now does a lot of the cleanup.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The message handler expected the SMI interface to keep a queue of
messages, but that was kind of silly, the queue would be easier to
manage in the message handler itself. As part of that, fix the
message cleanup to make sure no messages are outstanding when an
SMI interface is unregistered. This makes it easier for an SMI
interface to unregister, it just has to call ipmi_unregister_smi()
first and all processing from the message handler will be cleaned
up.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The handling of BMC flags wasn't quite right in a few places, mainly
around enabling and disabling interrupts in the BMC. Clean up the
code and fix the handling of the flags.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Embed the platform device in the bmc device instead of externally
allocating it, use more proper form for creating the device
attributes, and other general cleanups.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This patch fixes a bug on hotmod removing.
After ipmi interface is removed using hotmod, kernel panic occurs when
rmmod impi_si. For example, try this:
# echo "remove,"`cat /proc/ipmi/0/params` > \
/sys/module/ipmi_si/parameters/hotmod
# rmmod ipmi_si
Then, rmmod fails with the following messages.
------------[ cut here ]------------
WARNING: CPU: 12 PID: 10819 at /mnt/repos/linux/lib/list_debug.c:53 __list_del_entry+0x63/0xd0()
CPU: 12 PID: 10819 Comm: rmmod Not tainted 3.17.0-rc1 #19
Hardware name: FUJITSU-SV PRIMERGY BX920 S2/D3030, BIOS 080015 Rev.3D81.3030 02/10/2012
Call Trace:
dump_stack+0x45/0x56
warn_slowpath_common+0x7d/0xa0
warn_slowpath_fmt+0x4c/0x50
__list_del_entry+0x63/0xd0
list_del+0xd/0x30
cleanup_one_si+0x2a/0x230 [ipmi_si]
ipmi_pnp_remove+0x15/0x20 [ipmi_si]
pnp_device_remove+0x24/0x40
__device_release_driver+0x7f/0xf0
driver_detach+0xb0/0xc0
bus_remove_driver+0x55/0xd0
driver_unregister+0x2c/0x50
pnp_unregister_driver+0x12/0x20
cleanup_ipmi_si+0xbc/0xf0 [ipmi_si]
SyS_delete_module+0x132/0x1c0
system_call_fastpath+0x16/0x1b
---[ end trace 70b4377268f85c23 ]---
list_del in cleanup_one_si() fails because the smi_info is already
removed when hotmod removing.
When ipmi interface is removed by hotmod, smi_info is removed by
cleanup_one_si(), but is is still set in drvdata. Therefore when rmmod
ipmi_si, ipmi_pnp_remove tries to remove it again and fails.
By this patch, a pointer to smi_info in drvdata is cleared when hotmod
removing so that it will be not accessed when rmmod.
changelog:
v2:
- Clear drvdata in cleanup_one_si
- Change subject
v1:
https://lkml.org/lkml/2014/9/8/741
Signed-off-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building ipmi on arm with gcc-4.9 results in this warning for an
allmodconfig build:
drivers/char/ipmi/ipmi_si_intf.c: In function 'ipmi_thread':
include/linux/time.h:28:5: warning: 'busy_until.tv_sec' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (lhs->tv_sec > rhs->tv_sec)
^
drivers/char/ipmi/ipmi_si_intf.c:1007:18: note: 'busy_until.tv_sec' was declared here
struct timespec busy_until;
^
The warning is bogus and this case can not occur. Apparently this is a
false positive resulting from gcc getting a little smarter about
tracking assignments but not smart enough.
Marking the ipmi_thread_busy_wait function as inline gives the gcc
optimization logic enough information to figure out for itself that the
case cannot happen, which gets rid of the warning without adding any
fake initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an IPMI controller is used by the firmware and as such marked with
a reserved status, we shouldn't use it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code to send the channel config errors was missing an error report
in one place and needed some more information in another, and had an
extraneous bit of code. Clean all that up.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IPMI driver would wake up periodically looking for events and
watchdog pretimeouts. If there is nothing waiting for these events,
it's really kind of pointless to be checking for them. So modify the
driver so the message handler can pass down if it needs the lower layer
to be waiting for these. Modify the system interface lower layer to
turn off all timer and thread activity if the upper layer doesn't need
anything and it is not currently handling messages. And modify the
message handler to not restart the timer if its timer is not needed.
The timers and kthread will still be enabled if:
- the SI interface is handling a message.
- a user has enabled watching for events.
- the IPMI watchdog timer is in use (since it uses pretimeouts).
- the message handler is waiting on a remote response.
- a user has registered to receive commands.
This mostly affects interfaces without interrupts. Interfaces with
interrupts already don't use CPU in the system interface when the
interface is idle.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default probing can cause problems with some system, slow booting,
extra CPU usages, etc. Turn it off by default and give a config option
to enable it.
From: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The OBF timer in KCS was not reset in one situation when error recovery
was started, resulting in an immediate timeout.
Reported-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With recent changes it is possible for the timer handler to detect an
idle interface and not start the timer, but the thread to start an
operation at the same time. The thread will not start the timer in that
instance, resulting in the timer not running.
Instead, move all timer operations under the lock and start the timer in
the thread if it detect non-idle and the timer is not already running.
Moving under locks allows the last timeout to be set in both the thread
and the timer. 'Timer is not running' means that the timer is not
pending and smi_timeout() is not running. So we need a flag to detect
this correctly.
Also fix a few other timeout bugs: setting the last timeout when the
interrupt has to be disabled and the timer started, and setting the last
timeout in check_start_timer_thread possibly racing with the timer
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In read_all_bytes, we do
unsigned char i;
...
bt->read_data[0] = BMC2HOST;
bt->read_count = bt->read_data[0];
...
for (i = 1; i <= bt->read_count; i++)
bt->read_data[i] = BMC2HOST;
If bt->read_data[0] == bt->read_count == 255, we loop infinitely in the
'for' loop. Make 'i' an 'int' instead of 'char' to get rid of the
overflow and finish the loop after 255 iterations every time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-debugged-by: Rui Hui Dian <rhdian@novell.com>
Cc: Tomas Cech <tcech@suse.cz>
Cc: Corey Minyard <minyard@acm.org>
Cc: <openipmi-developer@lists.sourceforge.net>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: David Airlie <airlied@linux.ie>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Ashley Lai <ashley@ashleylai.com>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix
drivers/char/ipmi/ipmi_si_intf.c: In function 'ipmi_parisc_probe':
drivers/char/ipmi/ipmi_si_intf.c:2752:2: error: 'rv' undeclared (first use in this function)
drivers/char/ipmi/ipmi_si_intf.c:2752:2: note: each undeclared identifier is reported only once for each function it appears in
Introduced by commit d02b3709ff ("ipmi: Cleanup error return")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return proper errors for a lot of IPMI failure cases. Also call
pci_disable_device when IPMI PCI devices are removed.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Loading ipmi_si module while bmc is disconnected, we found the timeout
is longer than 5 secs. Actually it takes about 3 mins and 20
secs.(HZ=250)
error message as below:
Dec 12 19:08:59 linux kernel: IPMI BT: timeout in RD_WAIT [ ] 1 retries left
Dec 12 19:08:59 linux kernel: BT: write 4 bytes seq=0x01 03 18 00 01
[...]
Dec 12 19:12:19 linux kernel: IPMI BT: timeout in RD_WAIT [ ]
Dec 12 19:12:19 linux kernel: failed 2 retries, sending error response
Dec 12 19:12:19 linux kernel: IPMI: BT reset (takes 5 secs)
Dec 12 19:12:19 linux kernel: IPMI BT: flag reset [ ]
Function wait_for_msg_done() use schedule_timeout_uninterruptible(1) to
sleep 1 tick, so we should subtract jiffies_to_usecs(1) instead of 100
usecs from timeout.
Reported-by: Hu Shiyuan <hushiyuan@huawei.com>
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use USEC_PER_SEC instead of 1000000, that making the later bugfix
more clearly.
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The last line of PARISC machines (C8000, RP34x0, etc.) have a BMC for
controlling temperature, fan speed and other stuff. The BMC is
connected via a special bus and listed in the firmware device tree.
This change adds support for these BMCs to the IPMI driver.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'd submitted this about a year ago but it never made it upstream.
The latest versions of the kernel drivers for ipmi can use ACPI to
determine the type of BMC device used in the system. The following
patch adds a module alias so that udev will autoload the ipmi_si driver.
Signed-off-by: Jordan Hargrave <jordan_hargrave@dell.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
