Use the existing filter management functions to insert TCP/IPv4 and
UDP/IPv4 4-tuple filters for Receive Flow Steering.
For each channel, track how many RFS filters are being added during
processing of received packets and scan the corresponding number of
table entries for filters that may be reclaimed. Do this in batches
to reduce lock overhead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Implement the ndo_setup_tc() operation with 2 traffic classes.
Current Solarstorm controllers do not implement TX queue priority, but
they do allow queues to be 'paced' with an enforced delay between
packets. Paced and unpaced queues are scheduled in round-robin within
two separate hardware bins (paced queues with a large delay may be
placed into a third bin temporarily, but we won't use that). If there
are queues in both bins, the TX scheduler will alternate between them.
If we make high-priority queues unpaced and best-effort queues paced,
and high-priority queues are mostly empty, a single high-priority queue
can then instantly take 50% of the packet rate regardless of how many
of the best-effort queues have descriptors outstanding.
We do not actually want an enforced delay between packets on best-
effort queues, so we set the pace value to a reserved value that
actually results in a delay of 0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_channel_get_{rx,tx}_queue() currently return NULL if the channel
isn't used for traffic in that direction. In most cases this is a
bug, but some callers rely on it as an existence test.
Add existence test functions efx_channel_has_{rx_queue,tx_queues}()
and use them as appropriate.
Change efx_channel_get_{rx,tx}_queue() to assert that the requested
queue exists.
Remove now-redundant initialisation from efx_set_channels().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_hard_start_xmit() needs to implement a mapping which is the
inverse of tx_queue::core_txq. Move the initialisation of
tx_queue::core_txq next to efx_hard_start_xmit() to make the
connection more obvious.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Long before this driver went into mainline, it had support for
multiple TX queues per port, with lockless TX enabled. Since Linux
did not know anything of this, filling up any hardware TX queue would
stop the core TX queue and multiple hardware TX queues could fill up
before the scheduler reacted. Thus it was necessary to keep a count
of how many TX queues were stopped and to wake the core TX queue only
when all had free space again.
The driver also previously (ab)used the per-hardware-queue stopped
flag as a counter to deal with various things that can inhibit TX, but
it no longer does that.
Remove the per-channel tx_stop_count, tx_stop_lock and
per-hardware-queue stopped count and just use the networking core
queue state directly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Call netif_napi_{add,del}() on the NAPI contexts in the new and
old channels, respectively.
Since efx_init_napi() cannot fail, make its return type void.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
If we are using a legacy interrupt, our IRQ may be shared and our
interrupt handler may be called even though interrupts are disabled on
the NIC. When we change ring sizes, we reallocate the event queue and
the interrupt handler may use an invalid pointer when called for
another device's interrupt.
Maintain a legacy_irq_enabled flag and test that at the top of the
interrupt handler. Note that this problem results from the need to
work around broken INT_ISR0 reads, and does not affect the legacy
interrupt handler for Falcon A1.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
For some reason we failed to make this change when perm_addr was
introduced.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only have direct access to MDIO on Falcon, so move this out of
struct efx_nic.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only have direct access to SPI on Falcon, so move all this state
out of struct efx_nic.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make local functions and variable static. Do some rearrangement
of the string table stuff to put it where it gets used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This requires some reorganisation of channel setup and teardown to
ensure that we can always roll-back a failed change.
Based on work by Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Allow the ring size to be specified in non
power-of-two sizes (for instance to limit
the amount of receive buffers).
- Automatically size the event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow for reallocation of channel structures and rings.
Change module parameter separate_tx_channels to be read-only, since we
now require its value to be constant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for changes to the way channels and queue structures
are allocated, revise the macros and functions used to look up and
iterator over them.
- Replace efx_for_each_tx_queue() with iteration over channels then TX
queues
- Replace efx_for_each_rx_queue() with iteration over channels then RX
queues (with one exception, shortly to be removed)
- Introduce efx_get_{channel,rx_queue,tx_queue}() functions to look up
channels and queues by index
- Introduce efx_channel_get_{rx,tx}_queue() functions to look up a
channel's queues
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_over_errors appears to be intended as a count of packets that
overflow a packet buffer in the NIC. Given that we implement a
cut-through receive path, this should always be 0.
rx_dropped appears to be the correct counter for packets dropped due
to lack of host buffers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small possibility that a reader gets incorrect values on 32
bit arches. SNMP applications could catch incorrect counters when a
32bit high part is changed by another stats consumer/provider.
One way to solve this is to add a rtnl_link_stats64 param to all
ndo_get_stats64() methods, and also add such a parameter to
dev_get_stats().
Rule is that we are not allowed to use dev->stats64 as a temporary
storage for 64bit stats, but a caller provided area (usually on stack)
Old drivers (only providing get_stats() method) need no changes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow ethtool to query the number of RX rings, the fields used in RX
flow hashing and the hash indirection table.
Allow ethtool to update the RX flow hash indirection table.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will use this hash key for Toeplitz IPv4 hashing too.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace EFX_ERR() with netif_err(), EFX_INFO() with netif_info(),
EFX_LOG() with netif_dbg() and EFX_TRACE() and EFX_REGDUMP() with
netif_vdbg().
Replace EFX_ERR_RL(), EFX_INFO_RL() and EFX_LOG_RL() using explicit
calls to net_ratelimit().
Implement the ethtool operations to get and set message level flags,
and add a 'debug' module parameter for the initial value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_errors is defined as 'bad packets received', but we are currently
including various overflow errors as well.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insert a structure at the start of the shared page that
tracks the dma mapping refcnt. DMA into the next cache
line of the (shared) page (plus EFX_PAGE_IP_ALIGN).
When recycling a page, check the page refcnt. If the
page is otherwise unused, then resurrect the other
receive buffer that previously referenced the page.
Be careful not to overflow the receive ring, since we
can now resurrect n receive buffers in a row.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that efx_fast_push_rx_descriptors() must only run
from efx_process_channel() [NAPI], or when napi_disable()
has been executed.
Reimplement the slow fill by sending an event to the
channel, so that NAPI runs, and hanging the subsequent
fast fill off the event handler. Replace the sfc_refill
workqueue and delayed work items with a timer. We do
not need to stop this timer in efx_flush_all() because
it's safe to send the event always; receiving it will
be delayed until NAPI is restarted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain conditions a PHY may backpressure Falcon B0
in such a way that flushes timeout. In normal circumstances
the phy poller would fix the PHY, and the flush could complete.
But efx_nic_flush_queues() is always called after efx_stop_all(),
so the poller has been stopped. Even if this weren't the case,
how long would we have to wait for the poller to fix this? And
several callers of efx_nic_flush_queues() are about to reset
the device anyway - so we don't need to do anything.
Work around this bug by scheduling a reset. Ensure that the
MAC is never rewired back into the datapath before the reset
runs (we already ignore all rx events anyway).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_pm_freeze() sets efx->state = STATE_FINI, which means
efx_reset_work() will abort any scheduled resets.
efx_pm_thaw() should reschedule efx_reset_work() again,
since a freeze/thaw will not have reset the hardware.
This bug was spotted by inspection - there is no real world example of
this happening.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a core TX queue and 2 hardware TX queues for each channel.
If separate_tx_channels is set, create equal numbers of RX and TX
channels instead.
Rewrite the channel and queue iteration macros accordingly.
Eliminate efx_channel::used_flags as redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently TX completions do not count towards the NAPI budget. This
means a continuous stream of TX completions can cause the polling
function to loop indefinitely with scheduling disabled. To avoid
this, follow the common practice of reporting the budget spent after
processing one ring-full of TX completions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a regression introduced by commit
eb9f6744cb "sfc: Implement ethtool
reset operation".
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
From: Steve Hodgson <shodgson@solarflare.com>
Commit 357d46a17e "sfc: QT202x: Remove
unreliable MMD check at initialisation" broke initialisation of the
SFE4002. efx_mdio_reset_mmd() returns a positive value rather than 0
on success. The above commit causes this value to be propagated up
by qt202x_reset_phy(), which is treated as a failure by its callers.
Change qt202x_reset_phy() to return 0 if successful.
The PCI layer treats >0 as "fail, but please call remove() anyway",
which means that unloading the driver would cause a crash. Add a
WARN_ON() on the failure path of efx_pci_probe() to provide early
warning if there are any other cases where we do this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
