Hierarchically, the AB8500 is a child of the DB8500 PRCMU. So now that
Device Tree is being used and MFD core code is Device Tree aware, we
can simply register DB8500 PRCMU from Device Tree in the normal way
then allow the DB8500 PRCMU driver to register the AB8500 as a simple
MFD device at probe time.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We had a boot regression in Ux500 in the merge window because
two orthogonal pin control schemes for the PL011 were merged
at the same time:
- One using the .init() and .exit() hooks into the platform
for Ux500 putting the pins into default vs sleep state
respectively as the port was started/stopped.
commit a09806607f
"ARM: ux500: switch to using pinctrl for uart0"
- One hogging the default setting at PL011 probe()
commit 258e055111
"serial: amba-pl011: adopt pinctrl support"
To get a solution that works for both let's scrap the stuff
in the platform callbacks, instead have the driver itself
select default and sleep states when the port is
started/stopped. Hopefully this works for all clients.
Platform callbacks are bad for device tree migration anyway,
so this rids us of another problem in Ux500.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the correct compatible string for use during Device Tree
population. Without it the DB8500 PRCMU regulators would be processed
when DT is enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ST-Ericsson uses User Interface Boards to extend functionality of
some of their development boards. However, these aren't compatible
with all the supported boards found in Mainline (Snowball for
instance). This patch ensures that the UIBs are only probed on
boards which can actually support them. This in turn saves lots of
unnecessary error messages normally found in Snowball's boot log.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The final piece of the ab8500 puzzle. Here we prevent any of the ab8500-*
drivers from being registered from platform code when Device Tree is
enabled, as we expect DT do probe each of these individually. We also
provide the relevant compatible strings, so that DT knows which nodes
it needs to pay attention to during population.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The patch to disable SMSC911x registration was applied twice in the upstream
kernel by mistake. Git interpreted this as 'take the same entry from a
similar struct' which was close by. This was the wrong thing to do. This patch
rectifies this error and re-enables SMSC911x registration when Device Tree is
not enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now the SCMC911x is correctly enabled in Device Tree, there is no need
to continue registering it from platform code. In fact, if we continue
doing so, the system will throw an error on boot.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
During Device Tree enablement it is necessary to remove
<hw_component>_add_<device> calls one at at time, as and when particular
devices are DT enabled. This patch provides a temporary solution. Once
the new *of_init_devices function has been fully unpopulated it will be
removed again.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
During Device Tree enablement it is necessary to remove snowball_<device>*
platform_data segments one at at time, as and when particular devices are
DT enabled. This patch provides a temporary solution. Once this new struct
is empty it will be removed again.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rh0r
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPwHYJAAoJEIwa5zzehBx3PugP/2Wd6HN030iO5EhFBcBcrh5T
WaJ4KfzK3tWev5QA3idvenVNhk5My1HQ+PLij7BLpjNqKCKlNK0k/K9wMI5X827T
wkFFprdUcoMVrB1ZCjzwCk4/uTGWB5BMxoZ6mlBh1sZIR/yXo91t+wO971Uqr0ho
Ky1oW9uaPZ6Eja00iDLkfJfygquA5+zNb0a29q19zWnHlRkH76jtqZgfDKy9I2nq
virYZ4uhoPnY2g1JxhnaMNNC861CgfTDEtmtNjgeEbA6t9bbjqsZoQRhcYHZP4OM
a4Iu8FOyIvAAzQzUglfAZ4Ar4uYTmVRnG39XFh4wK/8tJYt0hEQwFS26B0pYKx/5
F76bwc4SqO7H9AWBF0WhyUbny5XmJcNwJjobm/oCeAvemTi3xA6BbubyfKMHPoIr
dDSEqcAcMt9G6sS48h3Pm0caEYDVzxf202vdylz1JABiJZi1W/7v+NMdhujfotJh
7IGehNRu0foPEsRIS9wsvD2TzSdQtDdjyFkGHd83XMc3JpvwmyePO6ynbbxrVnJJ
HzlPnbLIk3VyqyVCqVXj21NKEY1dbsYPItketAwwzc1BUGcld0qvQY/t/UI4JQT6
9vq77AwNjUhfomDdEWTp7aNx0whkY0R5KEY9jHjuu9WoE+xdPZbQKm589AJ6LA4U
j6HPMzWKUHOKT6g10rCl
=21h6
-----END PGP SIGNATURE-----
Merge tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sweeping late_initcall cleanup for arm-soc from Olof Johansson:
"This is a patch series from Shawn Guo that moves from individual
late_initcalls() to using a member in the machine structure to invoke
a platform's late initcalls.
This cleanup is a step in the move towards multiplatform kernels since
it would reduce the need to check for compatible platforms in each and
every initcall."
Fix up trivial conflicts in arch/arm/mach-{exynos/mach-universal_c210.c,
imx/mach-cpuimx51.c, omap2/board-generic.c} due to changes nearby (and,
in the case of cpuimx51.c the board support being deleted)
* tag 'cleanup-initcall' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: ux500: use machine specific hook for late init
ARM: tegra: use machine specific hook for late init
ARM: shmobile: use machine specific hook for late init
ARM: sa1100: use machine specific hook for late init
ARM: s3c64xx: use machine specific hook for late init
ARM: prima2: use machine specific hook for late init
ARM: pnx4008: use machine specific hook for late init
ARM: omap2: use machine specific hook for late init
ARM: omap1: use machine specific hook for late init
ARM: msm: use machine specific hook for late init
ARM: imx: use machine specific hook for late init
ARM: exynos: use machine specific hook for late init
ARM: ep93xx: use machine specific hook for late init
ARM: davinci: use machine specific hook for late init
ARM: provide a late_initcall hook for platform initialization
Pull crypto updates from Herbert Xu:
- New cipher/hash driver for ARM ux500.
- Code clean-up for aesni-intel.
- Misc fixes.
Fixed up conflicts in arch/arm/mach-ux500/devices-common.h, where quite
frankly some of it made no sense at all (the pull brought in a
declaration for the dbx500_add_platform_device_noirq() function, which
neither exists nor is used anywhere).
Also some trivial add-add context conflicts in the Kconfig file in
drivers/{char/hw_random,crypto}/
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: aesni-intel - move more common code to ablk_init_common
crypto: aesni-intel - use crypto_[un]register_algs
crypto: ux500 - Cleanup hardware identification
crypto: ux500 - Update DMA handling for 3.4
mach-ux500: crypto - core support for CRYP/HASH module.
crypto: ux500 - Add driver for HASH hardware
crypto: ux500 - Add driver for CRYP hardware
hwrng: Kconfig - modify default state for atmel-rng driver
hwrng: omap - use devm_request_and_ioremap
crypto: crypto4xx - move up err_request_irq label
crypto, xor: Sanitize checksumming function selection output
crypto: caam - add backward compatible string sec4.0
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
ab8500-i2c is used as core code to register the ab8500 device.
After allocating ab8500 memory, it immediately calls into
ab8500-core where the real initialisation takes place. This
patch moves all core registration and memory allocation into
the true ab8500-core file and removes ab8500-i2c completely.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds the required platform data and calls to enable
the CRYP/HASH driver.
Signed-off-by: Andreas Westin <andreas.westin@stericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
UART0 had a hack that enabled its pins on init and put it to
sleep on the exit callback. Replace this with the pinctrl calls
to do the same thing and update the runtime table with the two
apropriate states for runtime/active and idle.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Ux500 family to use the pinctrl driver for
configuring pins.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now the SCMC911x is correctly enabled in Device Tree, there is no need
to continue registering it from platform code. In fact, if we continue
doing so, the system will throw an error on boot.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch prevents i2c devices which are not present on the Snowball
low-cost development board from being registered. Devices such as;
tc3589x, bu1780 and lp5521 are present on other supported boards,
but are not located on Snowball.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create devices for the MSP-blocks (MSP0, MSP1, MSP2 and MSP3)
and associate it with the correct clocks in the clock-framework.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates Device Tree bindings for the Nomadik GPIO driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To allow for proper initialisation of the SMSC9115 Ethernet chip
and other devices which may be connected to the 'external bus',
Device Tree must first enable and traverse though it. This patch
enables the 'external bus' which will facilitate further
initialisation of its suborantate DT nodes.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This branch contains a number of updates for device tree support on
several ARM platforms, in particular:
* AT91 continues the device tree conversion adding support for a number of
on-chip drivers and other functionality
* ux500 adds probing of some of the core SoC blocks through device tree
* Initial device tree support for ST SPEAr600 platforms
* kirkwood continues the conversion to device-tree probing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wiKV
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: More device tree support updates" from Olof Johansson:
"This branch contains a number of updates for device tree support on
several ARM platforms, in particular:
* AT91 continues the device tree conversion adding support for a
number of on-chip drivers and other functionality
* ux500 adds probing of some of the core SoC blocks through device
tree
* Initial device tree support for ST SPEAr600 platforms
* kirkwood continues the conversion to device-tree probing"
Manually merge arch/arm/mach-ux500/Kconfig due to MACH_U8500 rename, and
drivers/usb/gadget/at91_udc.c due to header file include cleanups.
Also do an "evil merge" for the MACH_U8500 config option rename that the
affected RMI4 touchscreen driver in staging. It's called MACH_MOP500
now, and it was missed during previous merges.
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: SPEAr600: Add device-tree support to SPEAr600 boards
ARM: ux500: Provide local timer support for Device Tree
ARM: ux500: Enable PL022 SSP Controller in Device Tree
ARM: ux500: Enable PL310 Level 2 Cache Controller in Device Tree
ARM: ux500: Enable PL011 AMBA UART Controller for Device Tree
ARM: ux500: Enable Cortex-A9 GIC (Generic Interrupt Controller) in Device Tree
ARM: ux500: db8500: list most devices in the snowball device tree
ARM: ux500: split dts file for snowball into generic part
ARM: ux500: combine the board init functions for DT boot
ARM: ux500: Initial Device Tree support for Snowball
ARM: ux500: CONFIG: Enable Device Tree support for future endeavours
ARM: kirkwood: use devicetree for rtc-mv
ARM: kirkwood: rtc-mv devicetree bindings
ARM: kirkwood: fdt: define uart[01] as disabled, enable uart0
ARM: kirkwood: fdt: facilitate new boards during fdt migration
ARM: kirkwood: fdt: absorb kirkwood_init()
ARM: kirkwood: fdt: use mrvl ticker symbol
ARM: orion: wdt: use resource vice direct access
ARM: Kirkwood: Remove tclk from kirkwood_asoc_platform_data.
ARM: orion: spi: remove enable_clock_fix which is not used
...
This branch contains a handful of updates of SoC base code that had
dependencies on other external trees that have now been merged:
* Support for the new EXYNOS5250 SoC from Samsung
* SMP and power domain support for Tegra3 from NVIDIA
* ux500 updates for exporting SoC information through sysfs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPcpwnAAoJEIwa5zzehBx3RIQP/AvTVHF7EIXfu5XGLBYeKW+U
HBeT1kO1qL8m3gA/+DG/JzNpd8JDlILGob6hUN4lqA8f49MBkmttdbATZvBj4Nx+
T4+louPteiueexJdolj6hVCuNBhFJLgik3zMKGHvL8wbvqYHKpfqvuWWuzxtP3Hl
F1BvFSrQ5TZALGtNiRWDMwxFa2oA03ZNXjy+v9i3GIdn1vH18/IDryz7/7MW6GPv
NuKmZkcEpX2jDFe3AkqUMLxqMYizfuGg20FlV4tmxiF5Wlht6EiN38Y56LZgwuly
mde6AWN8qgwTYDk4cJ5ZVJtwkowosF5ko57V3SPmVaVc/WajZ0v28gt9YgNLVPL7
TXFEUJgIxzJnyM+DoSltzQ9tCsWUscQGmyPt4QSOLO2D76/3z+8+24/EwAIM/7Bj
u5/+74k5jDBZe1suCt/1P1Vr3l5Z3os483R7y4BtyLtWtQvBcjpkITj9lHmnsAf3
RqN2Z4osLcILwWVKa2y2DCOeJm0jvSCsn53+O3FGTSqhfwWTUVkqaDALeGXwJGbH
2rMks18BqJ2sT2ruFXHiVvZOj/8XxkcLsq8ztnuYoHQssrNtAtBM97l/xi1V7L0z
FmXnPszVA1mIkelsY2VDImEks/Iaad4o3Iuba9Yr3OKOSr/d8kLyB0reTmS/SHQL
u/o8ch/V5QVEo/H+ud7K
=X89H
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: More SoC support updates" from Olof Johansson:
"This branch contains a handful of updates of SoC base code that had
dependencies on other external trees that have now been merged:
* Support for the new EXYNOS5250 SoC from Samsung
* SMP and power domain support for Tegra3 from NVIDIA
* ux500 updates for exporting SoC information through sysfs"
Fix up trivial merge conflicts as per Olof.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: mach-shmobile: ap4evb: Reserve DMA memory for the frame buffer
ARM: EXYNOS: Fix compilation error with mach-exynos4-dt board
ARM: dts: add initial dts file for EXYNOS5250, SMDK5250
ARM: EXYNOS: add support device tree enabled board file for EXYNOS5
ARM: EXYNOS: add support ARCH_EXYNOS5 for EXYNOS5 SoCs
ARM: EXYNOS: add support get_core_count() for EXYNOS5250
ARM: EXYNOS: support EINT for EXYNOS4 and EXYNOS5
ARM: EXYNOS: add interrupt definitions for EXYNOS5250
ARM: EXYNOS: add support for EXYNOS5250 SoC
ARM: EXYNOS: add support uart for EXYNOS4 and EXYNOS5
ARM: EXYNOS: add initial setup-i2c0 for EXYNOS5
ARM: EXYNOS: add clock part for EXYNOS5250 SoC
ARM: EXYNOS: use exynos_init_uarts() instead of exynos4_init_uarts()
ARM: EXYNOS: to declare static for mach-exynos/common.c
ARM: EXYNOS: Add clkdev lookup entry for lcd clock
ARM: dt: Explicitly configure all serial ports on Tegra Cardhu
ARM: tegra: support for secondary cores on Tegra30
ARM: tegra: support for Tegra30 CPU powerdomains
ARM: tegra: add support for Tegra30 powerdomains
ARM: tegra: export tegra_powergate_is_powered()
...
This SSP Controller supports a number of serial communication methods
and as such cannot be registered using of_register_spi_devices.
Instead we register it simply as a primecell device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enables the 3 UARTs found on a u8500 using DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds all devices that are normally present through the
u8500_init_machine function in the device tree as well, which
will duplicate the devices that are visible.
This will not do much by itself because the device from the
device tree are not matched by any device driver until they
are converted as well. The next step is to move over one
device at a time to actually be used from the device tree
instead of the hardcoded device using auxdata to pass the
correct platform_data.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This lets us move over evertything to device tree one by one.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This provides very basic Device Tree support for ST-Ericsson's
low-cost development platform, Snowball. If Device Tree for
ux500 is enabled and the correct board is configured within the
Device Tree blob, the correct *_init_machine() will be called.
This patch is based on some original work completed by:
Niklas Hernaeus <niklas.hernaeus@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Niklas Hernaeus <niklas.hernaeus@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AB8500 GPIO1 is the base of AB8500 gpio number too.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At the request of Arnd Bergmann this patch moves all SoC
platform devices found in sysfs from /sys/devices/platform to
/sys/devices/soc<SoCNum>/. It is believed as the devices are
SoC specific and a /sys/devices/soc node has recently
become available, that this would be a more appropriate place to
display the data.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch provides a means for any device within ux500
platform code to allocate its own parent. This is particularly
prudent with the introduction of /sys/devices/socX, as a
device can now proclaim to be integral part of an SoC, rather
than a more generic platform device. Latter patches make good
use of this functionality.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Properly support the correct SDI-init sequence on the
ST-Ericsson HREFv60 and later boards in order to get
support for SD cards.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the ux500 platforms to be using the gic_handle_irq
function as their primary interrupt handler.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Do more work in the per-machine init calls instead of customizing
each init call.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The <[plat|mach]/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With SDI support for the Snowball we can boot from the
SD card.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Based on work from Mathieu J. Poirier <mathieu.poirier@linaro.org>
For more information on snowball please visit
http://www.igloocommunity.org
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
This board now has complete regulation constraints and can turn
off unused regulators. For the moment we need to wire VAUX1
(V-DISPLAY rail) always on since it somehow affects the external
MMC.
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch provides platform data for following
- uart reset function to assist uart register lockup workaround
- init/exit function to fix glitch in the tx pin in tty_open
when tty port0 is opened a glitch is seen in the tx line
of uart0. This happens in pl011_startup() when tx fifo
interrupt is provoked into asserting.
Now uart0 pins are enabled (alt function) only when init
is complete and turned back to gpio when closed.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This specifies the new per-platform timeout per I2C bus and
switches the I2C buses to fast mode, and increase the FIFO
depth to 8 for reads and writes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
