The CLKO is widely used by imx6q board designs to clock audio codec.
Since most codecs accept 24 MHz frequency, let's initially set up CLKO
with OSC24M (cko <-- cko2 <-- osc). Then those board specific CLKO
setup for audio codec can be removed.
The board dts files also need an update on cko reference in codec node.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Only imx6q has the ahci sata controller, enable
it on imx6q platforms.
Signed-off-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6q and imx6dl are two pin-to-pin compatible SoCs. The same board
design can work with either chip plugged into the socket, e.g. sabresd
and sabreauto boards.
We currently define pin groups in imx6q.dtsi and imx6dl.dtsi
respectively because the pad macro names are different between two
chips. This brings a maintenance burden on having the same label point
to the same pin group defined in two places.
The patch replaces prefix MX6Q_ and MX6DL_ with MX6QDL_ for both SoCs
pad macro names. Then the pin groups becomes completely common between
imx6q and imx6dl and can just be moved into imx6qdl.dtsi, so that the
long term maintenance of imx6q/dt pin settings becomes easier.
Unfortunately, the change brings some dramatic diff stat, but it's all
about DTS file, and the ultimate net diff stat is good.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently, all imx pinctrl drivers maintain a big array of struct
imx_pin_reg which hard-codes data like register offset and mux mode
setting for each pin function. Every time a new imx SoC support is
added, we need to add such a big mount of data. With moving to single
kernel build, it's only matter of time to be blamed on memory consuming.
With DTC pre-processor support in place, the patch moves all these data
into device tree by redefining the PIN_FUNC_ID in imxXX-pinfunc.h and
changing the PIN_FUNC_ID parsing code a little bit.
The pin id gets re-numbered based on mux register offset, or config
register offset if the pin has no mux register, so that kernel can
identify the pin id from register offsets provided by device tree.
As a bonus point of the change, those arbitrary magic numbers standing
for particular PIN_FUNC_ID in device tree sources are now replaced by
macros to improve the readability of dts files.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Replace /include/ (dtc) with #include (C pre-processor) for all imx DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.
This allows future use of #defines and header files in order to define
names for various constants, such as pinctrl settings. Use of those
features will increase the readability of the device tree files.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add dtsi for imx6q and imx6dl with non-common blocks moved into there.
Major differences between imx6dl and imx6q:
* Dual vs. Quad cores
* single vs. dual IPU
* 128 vs. 256 KB OCRAM
* imx6q: ECSPI5, OpenVG (GC355), SATA
* imx6dl: I2C4, PXP, EPDC, LCDIF
* iomuxc/pads definition
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
i.MX6 Quad and i.MX6 DualLite is similar enough to share one dtsi
file, so rename imx6q.dtsi to imx6qdl.dtsi preparing for the addition
of imx6dl support.
Another member of i.MX6 series i.MX6 SoloLite is different enough
from the other two, so it will stand as a separate dtsi. That's why
we rename to imx6qdl.dtsi not imx6.dtsi.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Following omap3-evm.dts way, it changes all imx dts files to use label
in board dts to refer to nodes defined by soc dtsi. Thus, the board
dts files become easier to read and edit with the least indentation
levels.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- add usbmisc device
- set property fsl,usbmisc for usb controllers
- set disable-over-current for imx6q-sabrelite usb otg
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It replaces the clk_register_clkdev in imx6q clock driver with DT
lookup. It depends on Mike's clk-3.7 branch.
When it gets merged together with imx-dt-3.7, there is a trivial
conflict on arch/arm/boot/dts/imx6q.dtsi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQTyFwAAoJEFBXWFqHsHzOcXkH/1a2RX8pUMsYHS5efpGaRUjJ
7PKKbAuMuGAgqdRDv1t2dcXuUv3zJgY/sdrivD9iwMqVSsQDW9MrdKyvBXg9m5UL
rg1Uc8r6mJlHSljimN8hoHp4PGFF7DCVls5y+3jsk/I2tWK+S/w00iP/aOFgkJNc
9Bg0ZhofKGOGpYK5joaBYAqvVM7F92gjpX+PytNEkJHGRKxCEsTRq4DRR3+r3uqs
GuoHOflYMEmviKYaZ/I14rwUJWFF4vIxuFC4vT88erpj3Fs0y7XkEWJiKU/2ma6M
w86qOUI6nU0iW5AILu3IvjSEvh2h/ZZ+5y3lVvzghcKK2QP4d4bEWnC745NRVSI=
=pxVx
-----END PGP SIGNATURE-----
Merge tag 'imx-clk-dt-lookup' into imx/dt-for-3.7-2
Conflicts:
arch/arm/boot/dts/imx6q.dtsi
It really becomes an maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx6q client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
'pinctrl_gpio_hog' is used to setup the pin functions, and it is not
neccesarily used only for GPIO pins, so remove 'gpio' from its name
to describe a more generic term.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Change the indentation for property fsl,pins a little bit, so that
the first and the last line get the same indentation with all other
lines. Then it will be easier to copy and past any of these lines.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In order to have audio functional on mx6qsabrelite, it is necessary
to setup the IOMUX for MX6Q_PAD_GPIO_0__CCM_CLKO pins as it provides
the audio clock.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Imx6q sabrelite board uses ecspi1 to connect a spi flash sst25vf016b,
we need to add pinctrl information for it in the dts, otherwise the
ecspi1 driver can't work and the connected flash is wrongly
detected as a mr25h256 flash like this:
m25p80 spi32766.0: found mr25h256, expected sst25vf016b
m25p80 spi32766.0: mr25h256 (32 Kbytes)
Cc: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx6qsabrelite has a sst25vf016b SPI NOR flash connected to eCSPI1.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It has been pointed out by device tree maintainer for several times
that the generic names 'serial' and 'ethernet' should be used for
those devices per ePAPR. Renames imx uart and fec device tree nodes
to stop them being bad examples.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
