Implement the bulk of interrupt return logic in C. The asm return code
must handle a few cases: restoring full GPRs, and emulating stack
store.
The stack store emulation is significantly simplfied, rather than
creating a new return frame and switching to that before performing
the store, it uses the PACA to keep a scratch register around to
perform the store.
The asm return code is moved into 64e for now. The new logic has made
allowance for 64e, but I don't have a full environment that works well
to test it, and even booting in emulated qemu is not great for stress
testing. 64e shouldn't be too far off working with this, given a bit
more testing and auditing of the logic.
This is slightly faster on a POWER9 (page fault speed increases about
1.1%), probably due to reduced mtmsrd.
mpe: Includes fixes from Nick for _TIF_EMULATE_STACK_STORE
handling (including the fast_interrupt_return path), to remove
trace_hardirqs_on(), and fixes the interrupt-return part of the
MSR_VSX restore bug caught by tm-unavailable selftest.
mpe: Incorporate fix from Nick:
The return-to-kernel path has to replay any soft-pending interrupts if
it is returning to a context that had interrupts soft-enabled. It has
to do this carefully and avoid plain enabling interrupts if this is an
irq context, which can cause multiple nesting of interrupts on the
stack, and other unexpected issues.
The code which avoided this case got the soft-mask state wrong, and
marked interrupts as enabled before going around again to retry. This
seems to be mostly harmless except when PREEMPT=y, this calls
preempt_schedule_irq with irqs apparently enabled and runs into a BUG
in kernel/sched/core.c
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-29-npiggin@gmail.com
When local_irq_enable() finds a pending soft-masked interrupt, it
"replays" it by setting up registers like the initial interrupt entry,
then calls into the low level handler to set up an interrupt stack
frame and process the interrupt.
This is not necessary, and uses more stack than needed. The high level
interrupt handler can be called directly from C, with just pt_regs set
up on stack. This should be faster and use less stack.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-28-npiggin@gmail.com
System call entry and particularly exit code is beyond the limit of
what is reasonable to implement in asm.
This conversion moves all conditional branches out of the asm code,
except for the case that all GPRs should be restored at exit.
Null syscall test is about 5% faster after this patch, because the
exit work is handled under local_irq_disable, and the hard mask and
pending interrupt replay is handled after that, which avoids games
with MSR.
mpe: Includes subsequent fixes from Nick:
This fixes 4 issues caught by TM selftests. First was a tm-syscall bug
that hit due to tabort_syscall being called after interrupts were
reconciled (in a subsequent patch), which led to interrupts being
enabled before tabort_syscall was called. Rather than going through an
un-reconciling interrupts for the return, I just go back to putting
the test early in asm, the C-ification of that wasn't a big win
anyway.
Second is the syscall return _TIF_USER_WORK_MASK check would go into
an infinite loop if _TIF_RESTORE_TM became set. The asm code uses
_TIF_USER_WORK_MASK to brach to slowpath which includes
restore_tm_state.
Third is system call return was not calling restore_tm_state, I missed
this completely (alhtough it's in the return from interrupt C
conversion because when the asm syscall code encountered problems it
would branch to the interrupt return code.
Fourth is MSR_VEC missing from restore_math, which was caught by
tm-unavailable selftest taking an unexpected facility unavailable
interrupt when testing VSX unavailble exception with MSR.FP=1
MSR.VEC=1. Fourth case also has a fixup in a subsequent patch.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-26-npiggin@gmail.com
The hdec interrupt handler is reported to sometimes fire in Linux if
KVM leaves it pending after a guest exists. This is harmless, so there
is a no-op handler for it.
The interrupt handler currently uses the regular kernel stack. Change
this to avoid touching the stack entirely.
This should be the last place where the regular Linux stack can be
accessed with asynchronous interrupts (including PMI) soft-masked.
It might be possible to take advantage of this invariant, e.g., to
context switch the kernel stack SLB entry without clearing MSR[EE].
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-17-npiggin@gmail.com
The real mode interrupt entry points currently use rfid to branch to
the common handler in virtual mode. This is a significant amount of
code, and forces other code (notably the KVM test) to live in the
real mode handler.
In the interest of minimising the amount of code that runs unrelocated
move the switch to virt mode into the common code, and do it with
mtmsrd, which avoids clobbering SRRs (although the post-KVMTEST
performance of real-mode interrupt handlers is not a big concern these
days).
This requires CTR to always be saved (real-mode needs to reach 0xc...)
but that's not a huge impact these days. It could be optimized away in
future.
mpe: Incorporate fix from Nick:
It's possible for interrupts to be replayed when TM is enabled and
suspended, for example rt_sigreturn, where the mtmsrd MSR_KERNEL in
the real-mode entry point to the common handler causes a TM Bad Thing
exception (due to attempting to clear suspended).
The fix for this is to have replay interrupts go to the _virt entry
point and skip the mtmsrd, which matches what happens before this
patch.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200225173541.1549955-11-npiggin@gmail.com
As per ISA an isync is only needed on instruction cache block
invalidate. Remove the same from dcache invalidate.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200320103242.229223-1-aneesh.kumar@linux.ibm.com
memcpy_mcsafe has been implemented for power machines which is used
by pmem infrastructure, so that an UE encountered during memcpy from
pmem devices would not result in panic instead a right error code
is returned. The implementation expects machine check handler to ignore
the event and set nip to continue the execution from fixup code.
Appropriate changes are already made to powernv machine check handler,
make similar changes to pseries machine check handler to ignore the
the event and set nip to continue execution at the fixup entry if we
hit UE at an instruction with a fixup entry.
while we are at it, have a common function which searches the exception
table entry and updates nip with fixup address, and any future common
changes can be made in this function that are valid for both architectures.
powernv changes are made by
commit 895e3dceeb ("powerpc/mce: Handle UE event for memcpy_mcsafe")
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reviewed-by: Santosh S <santosh@fossix.org>
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200326184916.31172-1-ganeshgr@linux.ibm.com
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
[mpe: Drop changes to a/p/boot which doesn't use linux headers]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190812215052.71840-10-ndesaulniers@google.com
With the EEH early probe now being pseries specific there's no need for
eeh_ops->probe() to take a pci_dn. Instead, we can make it take a pci_dev
and use the probe function to map a pci_dev to an eeh_dev. This allows
the platform to implement it's own method for finding (or creating) an
eeh_dev for a given pci_dev which also removes a use of pci_dn in
generic EEH code.
This patch also renames eeh_device_add_late() to eeh_device_probe(). This
better reflects what it does does and removes the last vestiges of the
early/late EEH probe split.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-6-oohall@gmail.com
The eeh_ops->probe() function is called from two different contexts:
1. On pseries, where we set EEH_PROBE_MODE_DEVTREE, it's called in
eeh_add_device_early() which is supposed to run before we create
a pci_dev.
2. On PowerNV, where we set EEH_PROBE_MODE_DEV, it's called in
eeh_device_add_late() which is supposed to run *after* the
pci_dev is created.
The "early" probe is required because PAPR requires that we perform an RTAS
call to enable EEH support on a device before we start interacting with it
via config space or MMIO. This requirement doesn't exist on PowerNV and
shoehorning two completely separate initialisation paths into a common
interface just results in a convoluted code everywhere.
Additionally the early probe requires the probe function to take an pci_dn
rather than a pci_dev argument. We'd like to make pci_dn a pseries specific
data structure since there's no real requirement for them on PowerNV. To
help both goals move the early probe into the pseries containment zone
so the platform depedence is more explicit.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-5-oohall@gmail.com
On pseries and PowerNV pcibios_bus_add_device() calls eeh_add_device_late()
so there's no need to do a separate tree traversal to bind the eeh_dev and
pci_dev together setting up the PHB at boot. As a result we can remove
eeh_add_device_tree_late().
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-2-oohall@gmail.com
Move creating the EEH specific sysfs files into eeh_add_device_late()
rather than being open-coded all over the place. Calling the function is
generally done immediately after calling eeh_add_device_late() anyway. This
is also a correctness fix since currently the sysfs files will be added
even if the EEH probe happens to fail.
Similarly, on pseries we currently add the sysfs files before calling
eeh_add_device_late(). This is flat-out broken since the sysfs files
require the pci_dev->dev.archdata.edev pointer to be set, and that is done
in eeh_add_device_late().
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-1-oohall@gmail.com
H_PAGE_THP_HUGE is used to differentiate between a THP hugepage and
hugetlb hugepage entries. The difference is WRT how we handle hash
fault on these address. THP address enables MPSS in segments. We want
to manage devmap hugepage entries similar to THP pt entries. Hence use
H_PAGE_THP_HUGE for devmap huge PTE entries.
With current code while handling hash PTE fault, we do set is_thp =
true when finding devmap PTE huge PTE entries.
Current code also does the below sequence we setting up huge devmap
entries.
entry = pmd_mkhuge(pfn_t_pmd(pfn, prot));
if (pfn_t_devmap(pfn))
entry = pmd_mkdevmap(entry);
In that case we would find both H_PAGE_THP_HUGE and PAGE_DEVMAP set
for huge devmap PTE entries. This results in false positive error like
below.
kernel BUG at /home/kvaneesh/src/linux/mm/memory.c:4321!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 56 PID: 67996 Comm: t_mmap_dio Not tainted 5.6.0-rc4-59640-g371c804dedbc #128
....
NIP [c00000000044c9e4] __follow_pte_pmd+0x264/0x900
LR [c0000000005d45f8] dax_writeback_one+0x1a8/0x740
Call Trace:
str_spec.74809+0x22ffb4/0x2d116c (unreliable)
dax_writeback_one+0x1a8/0x740
dax_writeback_mapping_range+0x26c/0x700
ext4_dax_writepages+0x150/0x5a0
do_writepages+0x68/0x180
__filemap_fdatawrite_range+0x138/0x180
file_write_and_wait_range+0xa4/0x110
ext4_sync_file+0x370/0x6e0
vfs_fsync_range+0x70/0xf0
sys_msync+0x220/0x2e0
system_call+0x5c/0x68
This is because our pmd_trans_huge check doesn't exclude _PAGE_DEVMAP.
To make this all consistent, update pmd_mkdevmap to set
H_PAGE_THP_HUGE and pmd_trans_huge check now excludes _PAGE_DEVMAP
correctly.
Fixes: ebd3119793 ("powerpc/mm: Add devmap support for ppc64")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200313094842.351830-1-aneesh.kumar@linux.ibm.com
Reorder Linux PTE bits to (almost) match Hash PTE bits.
RW Kernel : PP = 00
RO Kernel : PP = 00
RW User : PP = 01
RO User : PP = 11
So naturally, we should have
_PAGE_USER = 0x001
_PAGE_RW = 0x002
Today 0x001 and 0x002 and _PAGE_PRESENT and _PAGE_HASHPTE which
both are software only bits.
Switch _PAGE_USER and _PAGE_PRESET
Switch _PAGE_RW and _PAGE_HASHPTE
This allows to remove a few insns.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c4d6c18a7f8d9d3b899bc492f55fbc40ef38896a.1583861325.git.christophe.leroy@c-s.fr
The original 2005 patch that introduced the powerpc vdso, pre-git
("ppc64: Implement a vDSO and use it for signal trampoline") notes that:
... symbols exposed by the vDSO aren't "normal" function symbols, apps
can't be expected to link against them directly, the vDSO's are both
seen as if they were linked at 0 and the symbols just contain offsets
to the various functions. This is done on purpose to avoid a
relocation step (ppc64 functions normally have descriptors with abs
addresses in them). When glibc uses those functions, it's expected to
use it's own trampolines that know how to reach them.
Despite that explanation, there remains dead #ifdef
VDS64_HAS_DESCRIPTORS code-blocks that provide alternate function
definitions that setup function descriptors.
Since VDS64_HAS_DESCRIPTORS has been unused for all these years, we
might as well finally remove it from the codebase.
Signed-off-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200224211848.26087-1-joe.lawrence@redhat.com
Commit 2efc7c085f ("powerpc/32: drop get_pteptr()"),
replaced get_pteptr() by virt_to_kpte(). But virt_to_kpte() lacks a
NULL pmd check and returns an invalid non NULL pointer when there
is no page table.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Fixes: 2efc7c085f ("powerpc/32: drop get_pteptr()")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/b1177cdfc6af74a3e277bba5d9e708c4b3315ebe.1583575707.git.christophe.leroy@c-s.fr
With commit ("powerpc/numa: Early request for home node associativity"),
commit 2ea6263068 ("powerpc/topology: Get topology for shared
processors at boot") which was requesting home node associativity
becomes redundant.
Hence remove the late request for home node associativity.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200129135301.24739-6-srikar@linux.vnet.ibm.com
package_id is to match cores that are part of the same chip. On
PowerNV machines, package_id defaults to chip_id. However ibm,chip_id
property is not present in device-tree of PowerVM LPARs. Hence lscpu
output shows one core per socket and multiple cores.
To overcome this, use nid as the package_id on PowerVM LPARs.
Before the patch:
Architecture: ppc64le
Byte Order: Little Endian
CPU(s): 128
On-line CPU(s) list: 0-127
Thread(s) per core: 8
Core(s) per socket: 1 <----------------------
Socket(s): 16 <----------------------
NUMA node(s): 2
Model: 2.2 (pvr 004e 0202)
Model name: POWER9 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 32K
L1i cache: 32K
L2 cache: 512K
L3 cache: 10240K
NUMA node0 CPU(s): 0-63
NUMA node1 CPU(s): 64-127
#
# cat /sys/devices/system/cpu/cpu0/topology/physical_package_id
-1
After the patch:
Architecture: ppc64le
Byte Order: Little Endian
CPU(s): 128
On-line CPU(s) list: 0-127
Thread(s) per core: 8 <---------------------
Core(s) per socket: 8 <---------------------
Socket(s): 2
NUMA node(s): 2
Model: 2.2 (pvr 004e 0202)
Model name: POWER9 (architected), altivec supported
Hypervisor vendor: pHyp
Virtualization type: para
L1d cache: 32K
L1i cache: 32K
L2 cache: 512K
L3 cache: 10240K
NUMA node0 CPU(s): 0-63
NUMA node1 CPU(s): 64-127
#
# cat /sys/devices/system/cpu/cpu0/topology/physical_package_id
0
Now lscpu output is more in line with the system configuration.
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
[mpe: Use pkg_id instead of ppid, tweak change log and comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200129135121.24617-1-srikar@linux.vnet.ibm.com
current_stack_frame() doesn't return the stack pointer, but the
caller's stack frame. See commit bfe9a2cfe9 ("powerpc: Reimplement
__get_SP() as a function not a define") and commit
acf620ecf5 ("powerpc: Rename __get_SP() to current_stack_pointer()")
for details.
In some cases this is overkill or incorrect, as it doesn't return the
current value of r1.
So add a current_stack_pointer register global to get the value of r1
directly.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Split out of other patch, tweak change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200220115141.2707-2-mpe@ellerman.id.au
current_stack_pointer(), which was called __get_SP(), used to just
return the value in r1.
But that caused problems in some cases, so it was turned into a
function in commit bfe9a2cfe9 ("powerpc: Reimplement __get_SP() as a
function not a define").
Because it's a function in a separate compilation unit to all its
callers, it has the effect of causing a stack frame to be created, and
then returns the address of that frame. This is good in some cases
like those described in the above commit, but in other cases it's
overkill, we just need to know what stack page we're on.
On some other arches current_stack_pointer is just a register global
giving the stack pointer, and we'd like to do that too. So rename our
current_stack_pointer() to current_stack_frame() to make that
possible.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200220115141.2707-1-mpe@ellerman.id.au
Add a way to manually invoke a fast-reboot rather than setting the NVRAM
flag. The idea is to allow userspace to invoke a fast-reboot using the
optional string argument to the reboot() system call, or using the xmon
zr command so we don't need to leave around a persistent changes on
a system to use the feature.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200217024833.30580-2-oohall@gmail.com
On PPC32, pte_offset_map() does a kmap_atomic() in order to support
page tables allocated in high memory, just like ARM and x86/32.
But since at least 2008 and commit 8054a3428f ("powerpc: Remove dead
CONFIG_HIGHPTE"), page tables are never allocated in high memory.
When the page is in low mem, kmap_atomic() just returns the page
address but still disable preemption and pagefault. And it is
not an inlined function, so we suffer function call for no reason.
Make pte_offset_map() the same as pte_offset_kernel() and make
pte_unmap() void, in the same way as PPC64 which doesn't have HIGHMEM.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/03c97f0f6b3790d164822563be80f2fd4713a955.1581932480.git.christophe.leroy@c-s.fr
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because of this cleanup, we get to remove a few fields in struct
kvm_arch that are now unused.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[mpe: Fix build error in kvm/timing.c, adapt kvmppc_remove_cpu_debugfs()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200209105901.1620958-2-gregkh@linuxfoundation.org
Commit 8d30c14cab ("powerpc/mm: Rework I$/D$ coherency (v3)") and
commit 90ac19a8b2 ("[POWERPC] Abolish iopa(), mm_ptov(),
io_block_mapping() from arch/powerpc") removed the use of get_pteptr()
outside of mm/pgtable_32.c
In mm/pgtable_32.c, the only user of get_pteptr() is change_page_attr()
which operates on kernel context and on lowmem pages only.
Make virt_to_kpte() available outside of mm/mem.c and use it instead
of get_pteptr(), and drop get_pteptr()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/788378c6c3ba5c5298caab7c7f95e6c3c88244b8.1578558199.git.christophe.leroy@c-s.fr
At several places pmd pointer is retrieved through the same action:
pmd = pmd_offset(pud_offset(pgd_offset(mm, addr), addr), addr);
or
pmd = pmd_offset(pud_offset(pgd_offset_k(addr), addr), addr);
Refactor this by implementing two helpers pmd_ptr() and pmd_ptr_k()
This will help when adding the p4d level.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7b065c5be35726af4066cab238ee35cabceda1fa.1578558199.git.christophe.leroy@c-s.fr
In guests without hotplugagble memory drmem structure is only zero
initialized. Trying to manipulate DLPAR parameters results in a crash.
$ echo "memory add count 1" > /sys/kernel/dlpar
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
...
NIP: c0000000000ff294 LR: c0000000000ff248 CTR: 0000000000000000
REGS: c0000000fb9d3880 TRAP: 0300 Tainted: G E (5.5.0-rc6-2-default)
MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 28242428 XER: 20000000
CFAR: c0000000009a6c10 DAR: 0000000000000010 DSISR: 40000000 IRQMASK: 0
...
NIP dlpar_memory+0x6e4/0xd00
LR dlpar_memory+0x698/0xd00
Call Trace:
dlpar_memory+0x698/0xd00 (unreliable)
handle_dlpar_errorlog+0xc0/0x190
dlpar_store+0x198/0x4a0
kobj_attr_store+0x30/0x50
sysfs_kf_write+0x64/0x90
kernfs_fop_write+0x1b0/0x290
__vfs_write+0x3c/0x70
vfs_write+0xd0/0x260
ksys_write+0xdc/0x130
system_call+0x5c/0x68
Taking closer look at the code, I can see that for_each_drmem_lmb is a
macro expanding into `for (lmb = &drmem_info->lmbs[0]; lmb <=
&drmem_info->lmbs[drmem_info->n_lmbs - 1]; lmb++)`. When drmem_info->lmbs
is NULL, the loop would iterate through the whole address range if it
weren't stopped by the NULL pointer dereference on the next line.
This patch aligns for_each_drmem_lmb and for_each_drmem_lmb_in_range
macro behavior with the common C semantics, where the end marker does
not belong to the scanned range, and alters get_lmb_range() semantics.
As a side effect, the wraparound observed in the crash is prevented.
Fixes: 6c6ea53725 ("powerpc/mm: Separate ibm, dynamic-memory data from DT format")
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200131132829.10281-1-msuchanek@suse.de
hash_page() needs to read page tables from kernel memory. When entire
kernel memory is mapped by BATs, which is normally the case when
CONFIG_STRICT_KERNEL_RWX is not set, it works even if the page hosting
the page table is not referenced in the MMU hash table.
However, if the page where the page table resides is not covered by
a BAT, a DSI fault can be encountered from hash_page(), and it loops
forever. This can happen when CONFIG_STRICT_KERNEL_RWX is selected
and the alignment of the different regions is too small to allow
covering the entire memory with BATs. This also happens when
CONFIG_DEBUG_PAGEALLOC is selected or when booting with 'nobats'
flag.
Also, if the page containing the kernel stack is not present in the
MMU hash table, registers cannot be saved and a recursive DSI fault
is encountered.
To allow hash_page() to properly do its job at all time and load the
MMU hash table whenever needed, it must run with data MMU disabled.
This means it must be called before re-enabling data MMU. To allow
this, registers clobbered by hash_page() and create_hpte() have to
be saved in the thread struct together with SRR0, SSR1, DAR and DSISR.
It is also necessary to ensure that DSI prolog doesn't overwrite
regs saved by prolog of the current running exception. That means:
- DSI can only use SPRN_SPRG_SCRATCH0
- Exceptions must free SPRN_SPRG_SCRATCH0 before writing to the stack.
This also fixes the Oops reported by Erhard when create_hpte() is
called by add_hash_page().
Due to prolog size increase, a few more exceptions had to get split
in two parts.
Fixes: cd08f109e2 ("powerpc/32s: Enable CONFIG_VMAP_STACK")
Reported-by: Erhard F. <erhard_f@mailbox.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Erhard F. <erhard_f@mailbox.org>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206501
Link: https://lore.kernel.org/r/64a4aa44686e9fd4b01333401367029771d9b231.1581761633.git.christophe.leroy@c-s.fr
With HW assistance all page tables must be 4k aligned, the 8xx drops
the last 12 bits during the walk.
Redefine HUGEPD_SHIFT_MASK to mask last 12 bits out. HUGEPD_SHIFT_MASK
is used to for alignment of page table cache.
Fixes: 22569b881d ("powerpc/8xx: Enable 8M hugepage support with HW assistance")
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/778b1a248c4c7ca79640eeff7740044da6a220a0.1581264115.git.christophe.leroy@c-s.fr
Fix an existing bug in our user access handling, exposed by one of the bug fixes
we merged this cycle.
A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the recently
added CONFIG_VMAP_STACK.
Thanks to:
Christophe Leroy, Guenter Roeck.
-----BEGIN PGP SIGNATURE-----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=+Urh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix an existing bug in our user access handling, exposed by one of
the bug fixes we merged this cycle.
- A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
recently added CONFIG_VMAP_STACK.
Thanks to: Christophe Leroy, Guenter Roeck.
* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
powerpc/futex: Fix incorrect user access blocking
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
The early versions of our kernel user access prevention (KUAP) were
written by Russell and Christophe, and didn't have separate
read/write access.
At some point I picked up the series and added the read/write access,
but I failed to update the usages in futex.h to correctly allow read
and write.
However we didn't notice because of another bug which was causing the
low-level code to always enable read and write. That bug was fixed
recently in commit 1d8f739b07 ("powerpc/kuap: Fix set direction in
allow/prevent_user_access()").
futex_atomic_cmpxchg_inatomic() is passed the user address as %3 and
does:
1: lwarx %1, 0, %3
cmpw 0, %1, %4
bne- 3f
2: stwcx. %5, 0, %3
Which clearly loads and stores from/to %3. The logic in
arch_futex_atomic_op_inuser() is similar, so fix both of them to use
allow_read_write_user().
Without this fix, and with PPC_KUAP_DEBUG=y, we see eg:
Bug: Read fault blocked by AMR!
WARNING: CPU: 94 PID: 149215 at arch/powerpc/include/asm/book3s/64/kup-radix.h:126 __do_page_fault+0x600/0xf30
CPU: 94 PID: 149215 Comm: futex_requeue_p Tainted: G W 5.5.0-rc7-gcc9x-g4c25df5640ae #1
...
NIP [c000000000070680] __do_page_fault+0x600/0xf30
LR [c00000000007067c] __do_page_fault+0x5fc/0xf30
Call Trace:
[c00020138e5637e0] [c00000000007067c] __do_page_fault+0x5fc/0xf30 (unreliable)
[c00020138e5638c0] [c00000000000ada8] handle_page_fault+0x10/0x30
--- interrupt: 301 at cmpxchg_futex_value_locked+0x68/0xd0
LR = futex_lock_pi_atomic+0xe0/0x1f0
[c00020138e563bc0] [c000000000217b50] futex_lock_pi_atomic+0x80/0x1f0 (unreliable)
[c00020138e563c30] [c00000000021b668] futex_requeue+0x438/0xb60
[c00020138e563d60] [c00000000021c6cc] do_futex+0x1ec/0x2b0
[c00020138e563d90] [c00000000021c8b8] sys_futex+0x128/0x200
[c00020138e563e20] [c00000000000b7ac] system_call+0x5c/0x68
Fixes: de78a9c42a ("powerpc: Add a framework for Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org # v5.2+
Reported-by: syzbot+e808452bad7c375cbee6@syzkaller-ppc64.appspotmail.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200207122145.11928-1-mpe@ellerman.id.au
- Implement user_access_begin() and friends for our platforms that support
controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure" virtual
machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit VDSO, and
some other improvements.
- A series to use the PCI hotplug framework to control opencapi card's so that
they can be reset and re-read after flashing a new FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to:
Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen Zhou, Christophe Leroy,
Frederic Barrat, Greg Kurz, Jason A. Donenfeld, Joel Stanley, Jordan Niethe,
Julia Lawall, Krzysztof Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus
Walleij, Michael Bringmann, Nathan Chancellor, Nicholas Piggin, Nick
Desaulniers, Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy
Dunlap, Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago Jung
Bauermann, Tyrel Datwyler, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----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=xpG+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A pretty small batch for us, and apologies for it being a bit late, I
wanted to sneak Christophe's user_access_begin() series in.
Summary:
- Implement user_access_begin() and friends for our platforms that
support controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure"
virtual machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit
VDSO, and some other improvements.
- A series to use the PCI hotplug framework to control opencapi
card's so that they can be reset and re-read after flashing a new
FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to: Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy,
Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen
Zhou, Christophe Leroy, Frederic Barrat, Greg Kurz, Jason A.
Donenfeld, Joel Stanley, Jordan Niethe, Julia Lawall, Krzysztof
Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus Walleij, Michael
Bringmann, Nathan Chancellor, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy Dunlap,
Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain"
* tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (131 commits)
powerpc: configs: Cleanup old Kconfig options
powerpc/configs/skiroot: Enable some more hardening options
powerpc/configs/skiroot: Disable xmon default & enable reboot on panic
powerpc/configs/skiroot: Enable security features
powerpc/configs/skiroot: Update for symbol movement only
powerpc/configs/skiroot: Drop default n CONFIG_CRYPTO_ECHAINIV
powerpc/configs/skiroot: Drop HID_LOGITECH
powerpc/configs: Drop NET_VENDOR_HP which moved to staging
powerpc/configs: NET_CADENCE became NET_VENDOR_CADENCE
powerpc/configs: Drop CONFIG_QLGE which moved to staging
powerpc: Do not consider weak unresolved symbol relocations as bad
powerpc/32s: Fix kasan_early_hash_table() for CONFIG_VMAP_STACK
powerpc: indent to improve Kconfig readability
powerpc: Provide initial documentation for PAPR hcalls
powerpc: Implement user_access_save() and user_access_restore()
powerpc: Implement user_access_begin and friends
powerpc/32s: Prepare prevent_user_access() for user_access_end()
powerpc/32s: Drop NULL addr verification
powerpc/kuap: Fix set direction in allow/prevent_user_access()
powerpc/32s: Fix bad_kuap_fault()
...
Architectures for which we have hardware walkers of Linux page table
should flush TLB on mmu gather batch allocation failures and batch flush.
Some architectures like POWER supports multiple translation modes (hash
and radix) and in the case of POWER only radix translation mode needs the
above TLBI. This is because for hash translation mode kernel wants to
avoid this extra flush since there are no hardware walkers of linux page
table. With radix translation, the hardware also walks linux page table
and with that, kernel needs to make sure to TLB invalidate page walk cache
before page table pages are freed.
More details in commit d86564a2f0 ("mm/tlb, x86/mm: Support invalidating
TLB caches for RCU_TABLE_FREE")
The changes to sparc are to make sure we keep the old behavior since we
are now removing HAVE_RCU_TABLE_NO_INVALIDATE. The default value for
tlb_needs_table_invalidate is to always force an invalidate and sparc can
avoid the table invalidate. Hence we define tlb_needs_table_invalidate to
false for sparc architecture.
Link: http://lkml.kernel.org/r/20200116064531.483522-3-aneesh.kumar@linux.ibm.com
Fixes: a46cc7a90f ("powerpc/mm/radix: Improve TLB/PWC flushes")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Cc: <stable@vger.kernel.org> [4.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "Fixup page directory freeing", v4.
This is a repost of patch series from Peter with the arch specific changes
except ppc64 dropped. ppc64 changes are added here because we are redoing
the patch series on top of ppc64 changes. This makes it easy to backport
these changes. Only the first 2 patches need to be backported to stable.
The thing is, on anything SMP, freeing page directories should observe the
exact same order as normal page freeing:
1) unhook page/directory
2) TLB invalidate
3) free page/directory
Without this, any concurrent page-table walk could end up with a
Use-after-Free. This is esp. trivial for anything that has software
page-table walkers (HAVE_FAST_GUP / software TLB fill) or the hardware
caches partial page-walks (ie. caches page directories).
Even on UP this might give issues since mmu_gather is preemptible these
days. An interrupt or preempted task accessing user pages might stumble
into the free page if the hardware caches page directories.
This patch series fixes ppc64 and add generic MMU_GATHER changes to
support the conversion of other architectures. I haven't added patches
w.r.t other architecture because they are yet to be acked.
This patch (of 9):
A followup patch is going to make sure we correctly invalidate page walk
cache before we free page table pages. In order to keep things simple
enable RCU_TABLE_FREE even for !SMP so that we don't have to fixup the
!SMP case differently in the followup patch
!SMP case is right now broken for radix translation w.r.t page walk
cache flush. We can get interrupted in between page table free and
that would imply we have page walk cache entries pointing to tables
which got freed already. Michael said "both our platforms that run on
Power9 force SMP on in Kconfig, so the !SMP case is unlikely to be a
problem for anyone in practice, unless they've hacked their kernel to
build it !SMP."
Link: http://lkml.kernel.org/r/20200116064531.483522-2-aneesh.kumar@linux.ibm.com
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
walk_page_range() is going to be allowed to walk page tables other than
those of user space. For this it needs to know when it has reached a
'leaf' entry in the page tables. This information is provided by the
p?d_leaf() functions/macros.
For powerpc p?d_is_leaf() functions already exist. Export them using the
new p?d_leaf() name.
Link: http://lkml.kernel.org/r/20191218162402.45610-7-steven.price@arm.com
Signed-off-by: Steven Price <steven.price@arm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: "Liang, Kan" <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Zong Li <zong.li@sifive.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CRNG hasn't initialized, instead of the old blocking pool. Also clean
up archrandom.h, and some other miscellaneous cleanups.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAl40j1kACgkQ8vlZVpUN
gaPCywf8CWS9HFd2Iipj60gkTVugjlL5ib0lbfhQcAAwwzw1GLTXJSMBzzoMRHY/
ZI2sJZS1m0V1oWNnXXVKi+A1VXmlValWXAc+7fvbeaIe5pRT1EHP14s4Kz7/4d8Q
dk0b8cxNpR8u5CcbN8y9D+71IKpdksUbX7uGuGfw3bncQdRNwJVf+oS1fMGS0Rsb
F8ddQaED7iFpX2BMl56afQ4t2t0LA5+eLYMGoYoJx5fgd9BseP0TEcjj9Y4Z30M7
+GO4NZjUbAY0syx9r8hx3P/5miWZm2J9QJmJoXHhr5+IcAKM+6+Uo6X6gkOEqV4i
U//V1cqNuowV5ckE4Na+MfBillinsQ==
=HeFM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random changes from Ted Ts'o:
"Change /dev/random so that it uses the CRNG and only blocking if the
CRNG hasn't initialized, instead of the old blocking pool. Also clean
up archrandom.h, and some other miscellaneous cleanups"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (24 commits)
s390x: Mark archrandom.h functions __must_check
powerpc: Mark archrandom.h functions __must_check
powerpc: Use bool in archrandom.h
x86: Mark archrandom.h functions __must_check
linux/random.h: Mark CONFIG_ARCH_RANDOM functions __must_check
linux/random.h: Use false with bool
linux/random.h: Remove arch_has_random, arch_has_random_seed
s390: Remove arch_has_random, arch_has_random_seed
powerpc: Remove arch_has_random, arch_has_random_seed
x86: Remove arch_has_random, arch_has_random_seed
random: remove some dead code of poolinfo
random: fix typo in add_timer_randomness()
random: Add and use pr_fmt()
random: convert to ENTROPY_BITS for better code readability
random: remove unnecessary unlikely()
random: remove kernel.random.read_wakeup_threshold
random: delete code to pull data into pools
random: remove the blocking pool
random: make /dev/random be almost like /dev/urandom
random: ignore GRND_RANDOM in getentropy(2)
...
PPC: Bugfixes
x86:
* Support for mapping DAX areas with large nested page table entries.
* Cleanups and bugfixes here too. A particularly important one is
a fix for FPU load when the thread has TIF_NEED_FPU_LOAD. There is
also a race condition which could be used in guest userspace to exploit
the guest kernel, for which the embargo expired today.
* Fast path for IPI delivery vmexits, shaving about 200 clock cycles
from IPI latency.
* Protect against "Spectre-v1/L1TF" (bring data in the cache via
speculative out of bound accesses, use L1TF on the sibling hyperthread
to read it), which unfortunately is an even bigger whack-a-mole game
than SpectreV1.
Sean continues his mission to rewrite KVM. In addition to a sizable
number of x86 patches, this time he contributed a pretty large refactoring
of vCPU creation that affects all architectures but should not have any
visible effect.
s390 will come next week together with some more x86 patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeMxtCAAoJEL/70l94x66DQxIIAJv9hMmXLQHGFnUMskjGErR6
DCLSC0YRdRMwE50CerblyJtGsMwGsPyHZwvZxoAceKJ9w0Yay9cyaoJ87ItBgHoY
ce0HrqIUYqRSJ/F8WH2lSzkzMBr839rcmqw8p1tt4D5DIsYnxHGWwRaaP+5M/1KQ
YKFu3Hea4L00U339iIuDkuA+xgz92LIbsn38svv5fxHhPAyWza0rDEYHNgzMKuoF
IakLf5+RrBFAh6ZuhYWQQ44uxjb+uQa9pVmcqYzzTd5t1g4PV5uXtlJKesHoAvik
Eba8IEUJn+HgQJjhp3YxQYuLeWOwRF3bwOiZ578MlJ4OPfYXMtbdlqCQANHOcGk=
=H/q1
-----END PGP SIGNATURE-----
Merge tag 'kvm-5.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"This is the first batch of KVM changes.
ARM:
- cleanups and corner case fixes.
PPC:
- Bugfixes
x86:
- Support for mapping DAX areas with large nested page table entries.
- Cleanups and bugfixes here too. A particularly important one is a
fix for FPU load when the thread has TIF_NEED_FPU_LOAD. There is
also a race condition which could be used in guest userspace to
exploit the guest kernel, for which the embargo expired today.
- Fast path for IPI delivery vmexits, shaving about 200 clock cycles
from IPI latency.
- Protect against "Spectre-v1/L1TF" (bring data in the cache via
speculative out of bound accesses, use L1TF on the sibling
hyperthread to read it), which unfortunately is an even bigger
whack-a-mole game than SpectreV1.
Sean continues his mission to rewrite KVM. In addition to a sizable
number of x86 patches, this time he contributed a pretty large
refactoring of vCPU creation that affects all architectures but should
not have any visible effect.
s390 will come next week together with some more x86 patches"
* tag 'kvm-5.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
x86/KVM: Clean up host's steal time structure
x86/KVM: Make sure KVM_VCPU_FLUSH_TLB flag is not missed
x86/kvm: Cache gfn to pfn translation
x86/kvm: Introduce kvm_(un)map_gfn()
x86/kvm: Be careful not to clear KVM_VCPU_FLUSH_TLB bit
KVM: PPC: Book3S PR: Fix -Werror=return-type build failure
KVM: PPC: Book3S HV: Release lock on page-out failure path
KVM: arm64: Treat emulated TVAL TimerValue as a signed 32-bit integer
KVM: arm64: pmu: Only handle supported event counters
KVM: arm64: pmu: Fix chained SW_INCR counters
KVM: arm64: pmu: Don't mark a counter as chained if the odd one is disabled
KVM: arm64: pmu: Don't increment SW_INCR if PMCR.E is unset
KVM: x86: Use a typedef for fastop functions
KVM: X86: Add 'else' to unify fastop and execute call path
KVM: x86: inline memslot_valid_for_gpte
KVM: x86/mmu: Use huge pages for DAX-backed files
KVM: x86/mmu: Remove lpage_is_disallowed() check from set_spte()
KVM: x86/mmu: Fold max_mapping_level() into kvm_mmu_hugepage_adjust()
KVM: x86/mmu: Zap any compound page when collapsing sptes
KVM: x86/mmu: Remove obsolete gfn restoration in FNAME(fetch)
...
Unfortunately, GCC 9.1 is expected to be be released without support for
MPX. This means that there was only a relatively small window where
folks could have ever used MPX. It failed to gain wide adoption in the
industry, and Linux was the only mainstream OS to ever support it widely.
Support for the feature may also disappear on future processors.
This set completes the process that we started during the 5.4 merge window.
-----BEGIN PGP SIGNATURE-----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=g4cC
-----END PGP SIGNATURE-----
Merge tag 'mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/daveh/x86-mpx
Pull x86 MPX removal from Dave Hansen:
"MPX requires recompiling applications, which requires compiler
support. Unfortunately, GCC 9.1 is expected to be be released without
support for MPX. This means that there was only a relatively small
window where folks could have ever used MPX. It failed to gain wide
adoption in the industry, and Linux was the only mainstream OS to ever
support it widely.
Support for the feature may also disappear on future processors.
This set completes the process that we started during the 5.4 merge
window when the MPX prctl()s were removed. XSAVE support is left in
place, which allows MPX-using KVM guests to continue to function"
* tag 'mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/daveh/x86-mpx:
x86/mpx: remove MPX from arch/x86
mm: remove arch_bprm_mm_init() hook
x86/mpx: remove bounds exception code
x86/mpx: remove build infrastructure
x86/alternatives: add missing insn.h include
* Fix compile warning on 32-bit machines
* Fix locking error in secure VM support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJeMiC8AAoJEJ2a6ncsY3GfGg8H/03p+jc/aCKcA75ZeQPlzhmu
KWvSBbPATNcQiYOLfIvbB9AMXUPoyIfiblW/On8G6COFypsIhhUTwEfPUjWIBHNX
IwCfzoyf0gDRTi7A7gTDD06ZE+stikxJu59agX2Gc8kTIQ8ge340VR8J95Ol8/n2
/hVA8S/ORrdv8/KaCcvvIwc1V7OV6xBuGsTUOUvywzBTGDKd0CAbNzRwtS8LmWcM
OCkZX4G5DpFIYdsnjSBaSfwEVPAf3G1DzyQ801emwRnbAGYYgfakd1LwqdLDxptt
6CFHuIENEmmweJKMf9FBLWg+fOMl8wsv9l4mBIYt7coq5XPpi07yJ6yqSaJEToQ=
=Hmfo
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-next-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
Second KVM PPC update for 5.6
* Fix compile warning on 32-bit machines
* Fix locking error in secure VM support
This series is slightly unusual because it includes Arnd's compat
ioctl tree here:
1c46a2cf2d Merge tag 'block-ioctl-cleanup-5.6' into 5.6/scsi-queue
Excluding Arnd's changes, this is mostly an update of the usual
drivers: megaraid_sas, mpt3sas, qla2xxx, ufs, lpfc, hisi_sas. There
are a couple of core and base updates around error propagation and
atomicity in the attribute container base we use for the SCSI
transport classes. The rest is minor changes and updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXjHQJyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZZ8AQC02N+v
iUnTl1YxGPjIWBbnHuUxN2Qbb9D3C6gAT1LkigEArlk163K3A1XEQHF/VNCdAz/f
01XYTd3p1VHuegIBHlk=
=Cn52
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series is slightly unusual because it includes Arnd's compat
ioctl tree here:
1c46a2cf2d Merge tag 'block-ioctl-cleanup-5.6' into 5.6/scsi-queue
Excluding Arnd's changes, this is mostly an update of the usual
drivers: megaraid_sas, mpt3sas, qla2xxx, ufs, lpfc, hisi_sas.
There are a couple of core and base updates around error propagation
and atomicity in the attribute container base we use for the SCSI
transport classes.
The rest is minor changes and updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (149 commits)
scsi: hisi_sas: Rename hisi_sas_cq.pci_irq_mask
scsi: hisi_sas: Add prints for v3 hw interrupt converge and automatic affinity
scsi: hisi_sas: Modify the file permissions of trigger_dump to write only
scsi: hisi_sas: Replace magic number when handle channel interrupt
scsi: hisi_sas: replace spin_lock_irqsave/spin_unlock_restore with spin_lock/spin_unlock
scsi: hisi_sas: use threaded irq to process CQ interrupts
scsi: ufs: Use UFS device indicated maximum LU number
scsi: ufs: Add max_lu_supported in struct ufs_dev_info
scsi: ufs: Delete is_init_prefetch from struct ufs_hba
scsi: ufs: Inline two functions into their callers
scsi: ufs: Move ufshcd_get_max_pwr_mode() to ufshcd_device_params_init()
scsi: ufs: Split ufshcd_probe_hba() based on its called flow
scsi: ufs: Delete struct ufs_dev_desc
scsi: ufs: Fix ufshcd_probe_hba() reture value in case ufshcd_scsi_add_wlus() fails
scsi: ufs-mediatek: enable low-power mode for hibern8 state
scsi: ufs: export some functions for vendor usage
scsi: ufs-mediatek: add dbg_register_dump implementation
scsi: qla2xxx: Fix a NULL pointer dereference in an error path
scsi: qla1280: Make checking for 64bit support consistent
scsi: megaraid_sas: Update driver version to 07.713.01.00-rc1
...
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- Cleanup of the GOP [graphics output] handling code in the EFI stub
- Complete refactoring of the mixed mode handling in the x86 EFI stub
- Overhaul of the x86 EFI boot/runtime code
- Increase robustness for mixed mode code
- Add the ability to disable DMA at the root port level in the EFI
stub
- Get rid of RWX mappings in the EFI memory map and page tables,
where possible
- Move the support code for the old EFI memory mapping style into its
only user, the SGI UV1+ support code.
- plus misc fixes, updates, smaller cleanups.
... and due to interactions with the RWX changes, another round of PAT
cleanups make a guest appearance via the EFI tree - with no side
effects intended"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
efi/x86: Disable instrumentation in the EFI runtime handling code
efi/libstub/x86: Fix EFI server boot failure
efi/x86: Disallow efi=old_map in mixed mode
x86/boot/compressed: Relax sed symbol type regex for LLVM ld.lld
efi/x86: avoid KASAN false positives when accessing the 1: 1 mapping
efi: Fix handling of multiple efi_fake_mem= entries
efi: Fix efi_memmap_alloc() leaks
efi: Add tracking for dynamically allocated memmaps
efi: Add a flags parameter to efi_memory_map
efi: Fix comment for efi_mem_type() wrt absent physical addresses
efi/arm: Defer probe of PCIe backed efifb on DT systems
efi/x86: Limit EFI old memory map to SGI UV machines
efi/x86: Avoid RWX mappings for all of DRAM
efi/x86: Don't map the entire kernel text RW for mixed mode
x86/mm: Fix NX bit clearing issue in kernel_map_pages_in_pgd
efi/libstub/x86: Fix unused-variable warning
efi/libstub/x86: Use mandatory 16-byte stack alignment in mixed mode
efi/libstub/x86: Use const attribute for efi_is_64bit()
efi: Allow disabling PCI busmastering on bridges during boot
efi/x86: Allow translating 64-bit arguments for mixed mode calls
...
Pull RCU updates from Ingo Molnar:
"The RCU changes in this cycle were:
- Expedited grace-period updates
- kfree_rcu() updates
- RCU list updates
- Preemptible RCU updates
- Torture-test updates
- Miscellaneous fixes
- Documentation updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (69 commits)
rcu: Remove unused stop-machine #include
powerpc: Remove comment about read_barrier_depends()
.mailmap: Add entries for old paulmck@kernel.org addresses
srcu: Apply *_ONCE() to ->srcu_last_gp_end
rcu: Switch force_qs_rnp() to for_each_leaf_node_cpu_mask()
rcu: Move rcu_{expedited,normal} definitions into rcupdate.h
rcu: Move gp_state_names[] and gp_state_getname() to tree_stall.h
rcu: Remove the declaration of call_rcu() in tree.h
rcu: Fix tracepoint tracking RCU CPU kthread utilization
rcu: Fix harmless omission of "CONFIG_" from #if condition
rcu: Avoid tick_dep_set_cpu() misordering
rcu: Provide wrappers for uses of ->rcu_read_lock_nesting
rcu: Use READ_ONCE() for ->expmask in rcu_read_unlock_special()
rcu: Clear ->rcu_read_unlock_special only once
rcu: Clear .exp_hint only when deferred quiescent state has been reported
rcu: Rename some instance of CONFIG_PREEMPTION to CONFIG_PREEMPT_RCU
rcu: Remove kfree_call_rcu_nobatch()
rcu: Remove kfree_rcu() special casing and lazy-callback handling
rcu: Add support for debug_objects debugging for kfree_rcu()
rcu: Add multiple in-flight batches of kfree_rcu() work
...
Implement user_access_save() and user_access_restore()
On 8xx and radix:
- On save, get the value of the associated special register then
prevent user access.
- On restore, set back the saved value to the associated special
register.
On book3s/32:
- On save, get the value stored in current->thread.kuap and prevent
user access.
- On restore, regenerate address range from the stored value and
reopen read/write access for that range.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/54f2f74938006b33c55a416674807b42ef222068.1579866752.git.christophe.leroy@c-s.fr
Today, when a function like strncpy_from_user() is called,
the userspace access protection is de-activated and re-activated
for every word read.
By implementing user_access_begin and friends, the protection
is de-activated at the beginning of the copy and re-activated at the
end.
Implement user_access_begin(), user_access_end() and
unsafe_get_user(), unsafe_put_user() and unsafe_copy_to_user()
For the time being, we keep user_access_save() and
user_access_restore() as nops.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/36d4fbf9e56a75994aca4ee2214c77b26a5a8d35.1579866752.git.christophe.leroy@c-s.fr
In preparation of implementing user_access_begin and friends
on powerpc, the book3s/32 version of prevent_user_access() need
to be prepared for user_access_end().
user_access_end() doesn't provide the address and size which
were passed to user_access_begin(), required by prevent_user_access()
to know which segment to modify.
The list of segments which where unprotected by allow_user_access()
are available in current->kuap. But we don't want prevent_user_access()
to read this all the time, especially everytime it is 0 (for instance
because the access was not a write access).
Implement a special direction named KUAP_CURRENT. In this case only,
the addr and end are retrieved from current->kuap.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/55bcc1f25d8200892a31f67a0b024ff3b816c3cc.1579866752.git.christophe.leroy@c-s.fr
NULL addr is a user address. Don't waste time checking it. If
someone tries to access it, it will SIGFAULT the same way as for
address 1, so no need to make it special.
The special case is when not doing a write, in that case we want
to drop the entire function. This is now handled by 'dir' param
and not by the nulity of 'to' anymore.
Also make beginning of prevent_user_access() similar
to beginning of allow_user_access(), and tell the compiler
that writing in kernel space or with a 0 length is unlikely
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/85e971223dfe6ace734637db1841678939a76155.1579866752.git.christophe.leroy@c-s.fr
At the moment, bad_kuap_fault() reports a fault only if a bad access
to userspace occurred while access to userspace was not granted.
But if a fault occurs for a write outside the allowed userspace
segment(s) that have been unlocked, bad_kuap_fault() fails to
detect it and the kernel loops forever in do_page_fault().
Fix it by checking that the accessed address is within the allowed
range.
Fixes: a68c31fc01 ("powerpc/32s: Implement Kernel Userspace Access Protection")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/f48244e9485ada0a304ed33ccbb8da271180c80d.1579866752.git.christophe.leroy@c-s.fr
