Commit Graph

34 Commits

Author SHA1 Message Date
Vladimir Oltean
6c93099450 mii: Add helpers for parsing SGMII auto-negotiation
Typically a MAC PCS auto-configures itself after it receives the
negotiated copper-side link settings from the PHY, but some MAC devices
are more special and need manual interpretation of the SGMII AN result.

In other cases, the PCS exposes the entire tx_config_reg base page as it
is transmitted on the wire during auto-negotiation, so it makes sense to
be able to decode the equivalent lp_advertised bit mask from the raw u16
(of course, "lp" considering the PCS to be the local PHY).

Therefore, add the bit definitions for the SGMII registers 4 and 5
(local device ability, link partner ability), as well as a link_mode
conversion helper that can be used to feed the AN results into
phy_resolve_aneg_linkmode.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-05 23:22:32 -08:00
Russell King
4cf6c57e61 net: phy: fix write to mii-ctrl1000 register
When userspace writes to the MII_ADVERTISE register, we update phylib's
advertising mask and trigger a renegotiation.  However, writing to the
MII_CTRL1000 register, which contains the gigabit advertisement, does
neither.  This can lead to phylib's copy of the advertisement becoming
de-synced with the values in the PHY register set, which can result in
incorrect negotiation resolution.

Fixes: 5502b218e0 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-04 18:11:08 -07:00
Claudiu Manoil
7f07e5f1f7 net: mii: Fix PAUSE cap advertisement from linkmode_adv_to_lcl_adv_t() helper
With a recent link mode advertisement code update this helper
providing local pause capability translation used for flow
control link mode negotiation got broken.
For eth drivers using this helper, the issue is apparent only
if either PAUSE or ASYM_PAUSE is being advertised.

Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-27 22:49:06 -07:00
Andrew Lunn
6dbd0090f9 net: mii: mii_lpa_mod_linkmode_lpa_t: Make use of linkmode_mod_bit helper
Replace the if else code structure with a call to the helper
linkmode_mod_bit.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-05 16:26:16 -08:00
Andrew Lunn
d3351931a3 net: mii: Add mii_lpa_mod_linkmode_lpa_t
Add a _mod_ variant of mii_lpa_to_linkmode_lpa_t. Use this to fix the
genphy_read_status() where the 1G link partner features are getting
lost.

Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-05 16:26:16 -08:00
Andrew Lunn
78a24df370 net: mii: Rename mii_stat1000_to_linkmode_lpa_t
Rename mii_stat1000_to_linkmode_lpa_t to
mii_stat1000_mod_linkmode_lpa_t to indicate it modifies the passed
linkmode bitmap, without clearing any other bits.

Add a helper to set/clear bits in a linkmode.

Use this helper to ensure bit are clear which the stat1000 indicates
should not be set.

Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-05 16:26:16 -08:00
Andrew Lunn
5f15eed245 net: mii: Fix autoneg in mii_lpa_to_linkmode_lpa_t()
mii_adv_to_linkmode_adv_t() clears all bits before setting it needs to
set. This means the freshly set Autoneg gets cleared.

Change the order, and add comments about it clearing the old content
of the bitmap.

Fixes: c0ec3c2736 ("net: phy: Convert u32 phydev->lp_advertising to linkmode")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-05 16:26:16 -08:00
Andrew Lunn
fe1919147c net: phy: Fixup kerneldoc markup.
Add missing markup for function parameters

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11 10:10:01 -08:00
Andrew Lunn
c0ec3c2736 net: phy: Convert u32 phydev->lp_advertising to linkmode
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11 10:10:01 -08:00
Andrew Lunn
3c1bcc8614 net: ethernet: Convert phydev advertize and supported from u32 to link mode
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11 10:10:01 -08:00
Andrew Lunn
f954a04ea1 net: phy: Add limkmode equivalents to some of the MII ethtool helpers
Add helpers which take a linkmode rather than a u32 ethtool for
advertising settings.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-01 22:55:36 -07:00
Andrew Lunn
5f991f7bdd net: phy: Add helper for advertise to lcl value
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-01 22:55:36 -07:00
Andrew Lunn
edc7ccbbcf net: phy: Add helper to convert MII ADV register to a linkmode
The phy_mii_ioctl can be used to write a value into the MII_ADVERTISE
register in the PHY. Since this changes the state of the PHY, we need
to make the same change to phydev->advertising. Add a helper which can
convert the register value to a linkmode.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-01 22:55:36 -07:00
Andrew Lunn
b31cdffa23 net: phy: Move linkmode helpers to somewhere public
phylink has some useful helpers to working with linkmode bitmaps.
Move them to there own header so other code can use them.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-01 22:55:35 -07:00
Greg Kroah-Hartman
b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
yuval.shaia@oracle.com
82c01a84d5 net/{mii, smsc}: Make mii_ethtool_get_link_ksettings and smc_netdev_get_ecmd return void
Make return value void since functions never returns meaningfull value.

Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-05 11:00:42 -04:00
Philippe Reynes
bc8ee596af net: mii: add generic function to support ksetting support
The old ethtool api (get_setting and set_setting) has generic mii
functions mii_ethtool_sset and mii_ethtool_gset.

To support the new ethtool api ({get|set}_link_ksettings), we add
two generics mii function mii_ethtool_{get|set}_link_ksettings_get.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-02 15:17:09 -04:00
David Howells
607ca46e97 UAPI: (Scripted) Disintegrate include/linux
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
2012-10-13 10:46:48 +01:00
Giuseppe CAVALLARO
a59a4d1921 phy: add the EEE support and the way to access to the MMD registers.
This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).

An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.

In the end, this patch also adds the EEE ethtool support implementing:
 o phy_ethtool_set_eee
 o phy_ethtool_get_eee

v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
    values according to ethtool API (thanks to Ben's feedback).
    Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
    Fixed the phy_init_eee function: we need to check which link mode
    was autonegotiated and then the corresponding bits in 7.60 and 7.61
    registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
    when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
    and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-01 03:34:50 -07:00
Matt Carlson
37f07023d3 net: Change mii to ethtool advertisement function names
This patch implements advice by Ben Hutchings to change the mii side of
the function names to look more like the register whose values they
convert.  New LPA translation functions have been added as well.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-21 15:27:19 -05:00
Matt Carlson
28011cf19b net: Add ethtool to mii advertisment conversion helpers
Translating between ethtool advertisement settings and MII
advertisements are common operations for ethernet drivers.  This patch
adds a set of helper functions that implements the conversion.  The
patch then modifies a couple of the drivers to use the new functions.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-16 18:36:59 -05:00
Mark Einon
e8aaebc6b2 mii: Remove references to DP83840 PHY in mii.h
There are references to this PHY chip in the generic mii.h header, so removing them.
Re-jiggle the changed comments, in response to points raised by Ben Hutchings.

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15 15:36:34 -04:00
Mark Einon
c44f7eb4c1 mii: Convert spaces to tabs in mii.h
Whitespace changes - spaces converted to tabs after each define name and value

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-15 15:36:34 -04:00
Matt Carlson
221c56373e tg3: Migrate phy preprocessor defs to system defs
This patch changes to code to use some of the preprocessor
definitions from mii.h over its homegrown equivalents.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
2011-06-15 11:11:57 -04:00
Ben Hutchings
a8c30832b5 mii: Add mii_advertise_flowctrl()
This converts flow control capabilites to an advertising mask and can
be useful in combination with mii_resolve_flowctrl_fdx().

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-29 17:32:35 -07:00
Ben Hutchings
44c22ee91b mii: Simplify mii_resolve_flowctrl_fdx()
This is a shorter and more comprehensible formulation of the
conditions for each flow control mode.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-29 17:32:35 -07:00
Steve Glendinning
bc02ff95fe net: Refactor full duplex flow control resolution
These 4 drivers have identical full duplex flow control resolution
functions.  This patch changes them all to use one common function.

The function in question decides whether a device should enable TX and
RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this
should also be useful for other drivers.

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-16 02:00:48 -08:00
Steve Glendinning
e18ce34654 net: Move flow control definitions to mii.h
flags used within drivers for indicating tx and rx flow control are
defined in 4 drivers (and probably more), move these constants to mii.h.

The 3 SMSC drivers use the same constants (FLOW_CTRL_TX), but TG3 uses
TG3_FLOW_CTRL_TX, so this patch also renames the constants within TG3.

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-16 02:00:00 -08:00
David S. Miller
689d79469b [NET]: Fix BMSR_100{HALF,FULL}2 defines in linux/mii.h
Noticed by Matvejchikov Ilya.

Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-17 14:20:29 -07:00
David Woodhouse
c3ce7e203a Sanitise ethtool.h and mii.h for userspace.
They shouldn't be using 'u32' et al in structures which are used for
communication with userspace. Switch to the proper types (__u32 etc).

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2006-04-29 01:53:47 +01:00
Dale Farnsworth
43ec6e95e4 [PATCH] mii: Add test for GigE support
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-09-14 08:46:21 -04:00
Andy Fleming
00db8189d9 This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling
ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2005-07-30 19:31:23 -04:00
Michael Chan
b6016b7673 [BNX2]: New Broadcom gigabit network driver.
A new driver bnx2 for Broadcom bcm5706 is available.

The patch also includes new 1000BASE-X advertisement bit definitions in
mii.h

Thanks to David Miller and Jeff Garzik for reviewing and their valuable
feedback.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2005-05-26 13:03:09 -07:00
Linus Torvalds
1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00