Starting with commit 8947e396a8 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Seems to be a left-over from an automatic merge.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit 78b81f4666 ("ARM: dts: imx28-evk: Run I2C0 at 400kHz") caused issues
when doing the following sequence in loop:
- Boot the kernel
- Perform audio playback
- Reboot the system via 'reboot' command
In many times the audio card cannot be probed, which causes playback to fail.
After restoring to the original i2c0 frequency of 100kHz there is no such
problem anymore.
This reverts commit 78b81f4666.
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The lcdif node has a property named "display" and also a child node
called "display", which causes the following warning:
device-tree: Duplicate name in lcdif@80030000, renamed to "display#1"
Rename the child node name in order to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
It is safe to operate I2C0 at 400kHz as SGTL5000 supports this frequency.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The device tree specification recommends that generic name should be
used for nodes. So instead of naming those fixed regulator nodes
arbitrarily, let's use the generic name 'regulator@num' for those nodes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Most of this branch consists of updates, additions and general churn of
the device tree source files in the kernel (arch/arm/boot/dts). Besides
that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board files
for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well
- Some updates to pinctrl and other subsystems. Most of these are for
DT-enablement of the various platforms and acks have been collected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nH67
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
This is an RFC for the new touchscreen properties.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
CC: linux-arm-kernel@lists.infradead.org
CC: linux-input@vger.kernel.org
CC: devel@driverdev.osuosl.org
CC: Marek Vasut <marex@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: devicetree@vger.kernel.org
Convert mx23/mx28 dts files to use the padconfig defintions from
mxs-pinfunc.h.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Convert mx23/mx28 dts filed to use the pinctrl header files.
NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts
According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX
I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Provide 'lradc-touchscreen-wires' property to the LRADC driver, so that
touchscreen can be functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add the RTS/CTS property for auart0 which means we enable the
DMA support for it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These systems all use saif0 as the mclock provider to codec sgtl5000.
Reflect that in device tree source, so that sgtl5000 can find the clock
by calling clk_get().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of using a GPIO to turn on/off the CAN transceiver, it is better to
use a regulator as some systems may use a PMIC to power the CAN transceiver.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Instead of using a custom binding for retrieving the GPIO that activates the
LCD from devicetree, use a standard regulator.
This approach has the advantage to be more generic.
For example: in the case of a board that has a PMIC supplying the LCD voltage,
the current approach would not work, as it only searches for a GPIO pin.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Move display timing configurations into device tree, so that the
auxdata for mxsfb driver can be killed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit 8fe4554f (leds: leds-gpio: adopt pinctrl support) gpio-led driver
has pinctrl support, so setup the gpio led pin via pinctrl and avoid the
following warning:
leds-gpio leds.12: pins are not configured from the driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx28evk has a free slot U50 that can be used to populate an I2C EEPROM.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx28evk has a free slot (J89) which can be used to populate an SPI NOR Flash.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
hog_pins is used to setup the pin functions, and it is not neccesarily used only
for GPIO pins, so use only 'hog' to describe a more generic term.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The presence and muxing of lcdif control pins can vary much on different
boards. Move them into imx28-evk.dts to make lcdif_24bit_pins_a only
about data pins, so that it can be reused by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Only pins GPMI_CE0N and GPMI_READY0 are generally used by other boards.
Move GPMI_CE1N and GPMI_READY1 into imx28-evk.dts to make gpmi_pins_a
more general, and can be used by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add missing properties for fec, phy-supply, phy-reset-gpios and
phy-reset-duration, which are required by fec driver for successfully
probe fec from device tree, if bootloader hasn't set those things up.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add vmmc-supply for mmc device, so that the power to mmc slot can be
turned on by mmc driver if bootloader hasn't done it.
Also remove "okay" status for mmc1/ssp1, as the device has pin conflict
with gpmi-nand. Actually the device is already disabled since the
mxs-mmc driver adopts pinctrl support because there is no pinctrl setup
for the device in dts. Make this explicit by removing "okay" status.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Before gpio_request can directly ask pinctrl system to configure the
requested pin into gpio mode, we use "hog" entry (pinctrl state of
pin controller itself) to configure gpios.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
add gpmi-nand device tree support.
add gpmi-nand pinctrl support.
Also enable the gpmi support for mx28-evk board.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch includes basic dt support which can boot via nfs rootfs.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
