A PF today holds 2 different arrays - one holding information
about the HW configuration and one holding information about
the SBs that are used by the protocol drivers.
These arrays aren't really connected - e.g., protocol driver
initializing a given SB would not mark the same SB as occupied
in the HW shadow array.
Move into a single array [at least for PFs] - hold the mapping
of the driver-protocol SBs on the HW entry which they configure.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds hardware channel APIs support between
VF and PF for tunnelling configuration for the VFs.
According to that configuration VFs can run VXLAN/GENEVE/GRE
tunnels over it with tunnel features offloaded.
Using these APIs VF can also request for UDP ports configuration
to the PF, although PF and it's child VFs share the same port.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for UDP ports in bulletin board
to notify UDP ports change to the VFs
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF<->VF interface allows for the VF to request
multiple queues closure via a single message, but this has
never been used by any official driver.
We now deprecate this option, forcing each queue close
to arrive via a different command; This would be required
for future TLVs that are going to extend the queue TLVs with
additional information on a per-queue basis.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the submission of the qedr driver, there's inconsistency
in the licensing of the various qed/qede files - some are GPLv2
and some are dual-license.
Since qedr requires dual-license and it's dependent on both,
we're updating the licensing of all qed/qede source files.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to maintain several FW/HW-indices for each one of
its queues. Currently, that mapping is done by the QED where it uses
an rx/tx array of so-called hw-cids, populating them whenever a new
queue is opened and clearing them upon destruction of said queues.
This maintenance is far from ideal - there's no real reason why
QED needs to maintain such a data-structure. It becomes even worse
when considering the fact that the PF's queues and its child VFs' queues
are all mapped into the same data-structure.
As a by-product, the set of parameters an interface needs to supply for
queue APIs is non-trivial, and some of the variables in the API
structures have different meaning depending on their exact place
in the configuration flow.
This patch re-organizes the way L2 queues are configured and maintained.
In short:
- Required parameters for queue init are now well-defined.
- Qed would allocate a queue-cid based on parameters.
Upon initialization success, it would return a handle to caller.
- Queue-handle would be maintained by entity requesting queue-init,
not necessarily qed.
- All further queue-APIs [update, destroy] would use the opaque
handle as reference for the queue instead of various indices.
The possible owners of such handles:
- PF queues [qede] - complete handles based on provided configuration.
- VF queues [qede] - fw-context-less handles, containing only relative
information; Only the PF-side would need the absolute indices
for configuration, so they're omitted here.
- VF queues [qed, PF-side] - complete handles based on VF initialization.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When relaxing the limitation on the number of unicast MAC filters
an interface can configure, qed started passing the MAC quota to
qede. However, the value is initialized only for PFs, causing VFs
to always try and configure themselves as promiscuous
[as they believe they lack the resources to configure the rx-mode].
Fixes: 7b7e70f979 ("qed*: Allow unicast filtering")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Malicious VFs might be caught in several different methods:
- Misusing their bar permission and being blocked by hardware.
- Misusing their fastpath logic and being blocked by firmware.
- Misusing their interaction with their PF via hw-channel,
and being blocked by PF driver.
On the first two items, firmware would indicate to driver that
the VF is to be considered malicious, but would sometime still
allow the VF to communicate with the PF [depending on the exact
nature of the malicious activity done by the VF].
The current existing logic on the PF side lacks handling of such events,
and might allow the PF to perform some incorrect configuration on behalf
of a VF that was previously indicated as malicious.
The new scheme is simple -
Once the PF determines a VF is malicious it would:
a. Ignore any further requests on behalf of the VF-driver.
b. Prevent any configurations initiated by the hyperuser for
the malicious VF, as firmware isn't willing to serve such.
The malicious indication would be cleared upon the VF flr,
after which it would become usable once again.
Signed-off-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern VFs can't run on old non-compatible as the fastpath HSI is
slightly changed - but as the HSI is actually very close [basically,
a single bit whose meaning flipped] this can be supported with small
modifications.
The major differences would be in:
- Recognizing that VF is running on top of a legacy PF.
- Returning some slowpath configurations that are no longer needed
on top of modern PFs, but would be required when working over
the legacy ones.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8.10.x FW added support for forward compatability as well as
'future' backward compatibility, but only to those VFs that were
using HSI which was 8.10.x based or newer.
The latest firmware now supports backward compatibility for the
older VFs based on 8.7.x and 8.8.x firmware as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver require an exact match between VF and PF storm firmware;
Any difference would fail the VF acquire message, causing the VF probe
to be aborted.
While there's still dependencies between the two, the recent FW submission
has relaxed the match requirement - instead of an exact match, there's now
a 'fastpath' HSI major/minor scheme, where VFs and PFs that match in their
major number can co-exist even if their minor is different.
In order to accomadate this change some changes in the vf-start init flow
had to be made, as the VF start ramrod now has to be sent only after PF
learns which fastpath HSI its VF is requiring.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the PF to enforce the VF's mac.
i.e., by using `ip link ... vf <x> mac <value>'.
While a MAC is forced, PF would prevent the VF from configuring any other
MAC.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for PF control over the VF vlan configuration.
I.e., `ip link ... vf <x> vlan <vid>' should now be supported.
1. <vid> != 0 => VF receives [unknowingly] only traffic tagged by
<vid> and tags all outgoing traffic sent by VF with <vid>.
2. <vid> == 0 ==> Remove the pvid configuration, reverting to previous.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the VF infrastructure is supposed to offer backward/forward
compatibility, the various types associated with VF<->PF communication
should be aligned across all various platforms that support IOV
on our family of adapters.
This adds a couple of currently missing values, specifically aligning
the enum for the various TLVs possible in the communication between them.
It then adds the PF implementation for some of those missing VF requests.
This support isn't really necessary for the Linux VF as those VFs aren't
requiring it [at least today], but are required by VFs running on other
OSes. LRO is an example of one such configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up to this point, VF and PF communication always originates from VF.
As a result, VF cannot be notified of any async changes, and specifically
cannot be informed of the current link state.
This introduces the bulletin board, the mechanism through which the PF
is going to communicate async notifications back to the VF. basically,
it's a well-defined structure agreed by both PF and VF which the VF would
continuously poll and into which the PF would DMA messages when needed.
[Bulletin board is actually allocated and communicated in previous patches
but never before used]
Based on the bulletin infrastructure, the VF can query its link status
and receive said async carrier changes.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds sufficient changes to allow VFs l2-configuration flows to work.
While the fastpath of the VF and the PF are meant to be exactly the same,
the configuration of the VF is done by the PF.
This diverges all VF-related configuration flows that originate from a VF,
making them pass through the VF->PF channel and adding sufficient logic
on the PF side to support them.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While previous patches have already added the necessary logic to probe
VFs as well as enabling them in the HW, this patch adds the ability to
support VF FLR & SRIOV disable.
It then wraps both flows together into the first IOV callback to be
provided to the protocol driver - `configure'. This would later to be used
to enable and disable SRIOV in the adapter.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.
This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Communication between VF and PF is based on a dedicated HW channel;
VF will prepare a messge, and by signaling the HW the PF would get a
notification of that message existance. The PF would then copy the
message, process it and DMA an answer back to the VF as a response.
The messages themselves are TLV-based - allowing easier backward/forward
compatibility.
This patch adds the infrastructure of the channel on the PF side -
starting with the arrival of the notification and ending with DMAing
the response back to the VF.
It also adds a dummy-response as reference, as it only lays the
groundwork of the communication; it doesn't really add support of any
actual messages.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a new Kconfig option for qed* driver which would allow
[eventually] the support in VFs.
This patch adds the necessary logic in the PF to learn about the possible
VFs it will have to support [Based on PCI configuration space and HW],
and prepare a database with an entry per-VF as infrastructure for future
interaction with said VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
