There's little point in increasing the GPU frequency from the delayed
rps work on VLV. Now when the GPU is idle, the GPU frequency actually
keeps dropping gradually until it hits the minimum, whereas previously
it just ping-ponged constantly between RPe and RPe-1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I can't find GEN6_RP_INTERRUPT_LIMITS (0xA014) anywhere in VLV docs.
Reading it always returns zero from what I can tell, and eliminating
it doesn't seem to make any difference to the behaviour of the system.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eliminate the weird inverted logic from the rps new_delay comparison.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems that even though Punit reports the frequency change to have
been completed, it still reports the old frequency in the status
register for some time.
So rather than polling for Punit to complete the frequency change after
each request, poll before. This gets rid of the spurious "Punit overrode
GPU freq" messages.
This also lets us continue working while Punit is performing the actual
frequency change. As a result, openarena demo088-test1 timedemo average
fps is increased by ~5 fps, and the slowest frame duration is reduced
by ~25%.
The sysfs cur_freq file always reads the current frequency from Punit
anyway, so having rps.cur_delay be slightly off at times doesn't matter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always print both the MHz value and raw register value for rps stuff.
Also kill a somewhat pointless local 'rpe' variable and just use
dev_priv->rps.rpe_delay.
While at it clean up the caps in "GPU" and "Punit" debug messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Report back the user error of attempting to setup a CRTC with an invalid
framebuffer pitch. This is trickier than it should be as on gen4, there
is a restriction that tiled surfaces must have a stride less than 16k -
which is less than the largest supported CRTC size.
v2: Fix the limits for gen3
v3: Move check into intel_framebuffer_init() and fix VLV limits. (vsyrjala)
v4: Use idiomatic '>=' for generation checks
References: https://bugs.freedesktop.org/show_bug.cgi?id=65099
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to apply WaForceL3Serialization:vlv twice.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are legit cases, e.g. when userspace asks for something
impossible. So tune it down to debug output like we do with all other
userspace-triggerable warnings.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66111#c5
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Rebased.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec seems to be full of lies, at least it disagress with reality:
Two systems corrobated that SDVO hpd bits are the same as on gen3.
v2: Update comment a bit.
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Alex Fiestas <afiestas@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58405
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the trend and don't code conditions with platforms but with
features.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/i915/i915_gem.c: In function ‘i915_gem_object_bind_to_gtt’:
drivers/gpu/drm/i915/i915_gem.c:3002:3: warning: format ‘%ld’ expects
argument of type ‘long int’, but argument 5 has type ‘size_t’ [-Wformat]
v2: Use %zu instead of %d. Two char patch, and 100% wrong. (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nothing the user (nor we) really can do about this, but upsets a nice
quiet boot.
Note that this happens mostly on SDVs where OEMs obviously haven't had
a chance yet to appropriately trim the output list.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65988
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Amend commit message a bit to clarify a question from Paulo.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Git commit 90797e6d1e
("drm/i915: create compact dma scatter lists for gem objects") makes
certain assumptions about the under laying DMA API that are not always
correct.
On a ThinkPad X230 with an Intel HD 4000 with Xen during the bootup
I see:
[drm:intel_pipe_set_base] *ERROR* pin & fence failed
[drm:intel_crtc_set_config] *ERROR* failed to set mode on [CRTC:3], err = -28
Bit of debugging traced it down to dma_map_sg failing (in
i915_gem_gtt_prepare_object) as some of the SG entries were huge (3MB).
That unfortunately are sizes that the SWIOTLB is incapable of handling -
the maximum it can handle is a an entry of 512KB of virtual contiguous
memory for its bounce buffer. (See IO_TLB_SEGSIZE).
Previous to the above mention git commit the SG entries were of 4KB, and
the code introduced by above git commit squashed the CPU contiguous PFNs
in one big virtual address provided to DMA API.
This patch is a simple semi-revert - were we emulate the old behavior
if we detect that SWIOTLB is online. If it is not online then we continue
on with the new compact scatter gather mechanism.
An alternative solution would be for the the '.get_pages' and the
i915_gem_gtt_prepare_object to retry with smaller max gap of the
amount of PFNs that can be combined together - but with this issue
discovered during rc7 that might be too risky.
Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Imre Deak <imre.deak@intel.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: David Airlie <airlied@linux.ie>
CC: <dri-devel@lists.freedesktop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In some virtualized environments (e.g. XEN), there is irrelevant ISA bridge in
the system. To work reliably, we should scan trhough all the ISA bridge
devices and check for the first match, instead of only checking the first one.
Signed-off-by: Rui Guo <firemeteor@users.sourceforge.net>
[danvet: Fixup conflict with the num_pch_pll removal. And add
subsystem header to the commit message headline.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because it's the function that destroys the connector, not the
encoder. And we already have intel_dp_encoder_destroy.
This has annoyed me for a long time.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Various fixes that make surviving concurrent piglit more possible.
- Buffer object deletion no longer synchronous
- Context/register initialisation updates that have been reported to
solve some stability issues (particularly on some problematic GF119
chips)
- Kernel side support for VP2 video decoding engines
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (44 commits)
drm/nvd0-/disp: handle case where display engine is missing/disabled
drm/gr/nvc0-: merge nvc0/nve0 ucode, and use cpp instead of m4
drm/nouveau/bsp/nv84: initial vp2 engine implementation
drm/nouveau/vp/nv84: initial vp2 engine implementation
drm/nouveau/core: xtensa engine base class implementation
drm/nouveau/vdec: fork vp3 implementations from vp2
drm/nouveau/core: move falcon class to engine/
drm/nouveau/kms: don't fail if there's no dcb table entries
drm/nouveau: remove limit on gart
drm/nouveau/vm: perform a bar flush when flushing vm
drm/nvc0/gr: cleanup register lists, and add nvce/nvcf to switches
drm/nvc8/gr: update initial register/context values
drm/nvc4/gr: update initial register/context values
drm/nvc1/gr: update initial register/context values
drm/nvc3/gr: update initial register/context values
drm/nvc0/gr: update initial register/context values
drm/nvd9/gr: update initial register/context values
drm/nve4/gr: update initial register/context values
drm/nvc0-/gr: bump maximum gpc/tpc limits
drm/nvf0/gr: initial register/context setup
...
Not really "core" per-se. About to merge Ilia's work adding another
similar class for the VP2 xtensa engines, so, seems like a good time to
move all these to engine/.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Most graphics cards nowadays have a multiple of this limit as their vram,
so limiting GART doesn't seem to make much sense.
Signed-off-by: Maarten >Lnkhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Appears to fix the regression from "drm/nvc0/vm: handle bar tlb flushes
internally".
nvidia always seems to do this flush after writing values.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nvc0_vm_flush() accesses the pgd list, which will soon be able to race
with vm_unlink() during channel destruction.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
These operations can take quite some time, and we really don't want to
have to hold a spinlock for too long.
Now that the lock ordering for vm and the gr/nv84 hw bug workaround has
been reversed, it's possible to use a mutex here.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Helps us to get identical numbers to the binary driver for (at least)
Kepler memory PLLs, and fixes a rounding error.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
And, will depend on FB/VOLT/DAEMON being ready when it gets initialised
so that it can set/restore clocks.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
These are pretty much useless for reclocking purposes. Lets make it
clearer what they're for and move them to DEVINIT to signify they're
for the very simple PLL setting requirements of running the init
tables.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We've been ignoring this return value, so print a nice backtrace in
case it's not what we expected.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because calling intel_dp_encoder_destroy inside
intel_edp_init_connector is just wrong. This is the initialization
path, so we should properly unwind all the initialization through the
whole caller stack.
On the intel_dp_encoder_destroy function we do the following:
1 - Call i2c_del_adapter
2 - Call drm_encoder_cleanup
3 - If edp:
3.1 - Cancel panel_vdd_work
3.2 - Call ironlake_panel_vdd_of_sync
4 - Free the encoder
And here is how we unwind each specific step:
1 - We have intel_dp_init_connector -> intel_dp_i2c_init ->
i2c_dp_aux_add_bus -> i2c_add_adapter, so we call
i2c_del_dapter at intel_dp_init_connector
2 - Call it in the same function that called drm_encoder_init
3 - Call it in the same function that called INIT_DELAYED_WORK
4 - Free it in the same function that allocated it
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because calling intel_dp_destroy inside intel_edp_init_connector is
just wrong. This is the initialization path, so we should properly
unwind all the initialization through the whole caller stack.
On the intel_dp_destroy function we do the following:
1 - Free edid if it exists
2 - Call intel_panel_fini in case it's eDP
3 - Call drm_sysfs_connector_remove
4 - Call drm_connector_cleanup
5 - Free the connector
And here is how we unwind each specific step:
1 - No need as we still didn't assign anything
2 - No need as we still didn't call intel_panel_init
3 - Call it in the same function that called drm_sysfs_connector_add
4 - Call it in the same function that called drm_connector_init
5 - Free it in the same function that allocated it
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case we detect a "ghost eDP", intel_edp_init_connector frees both
the connector and encoder and then returns. On Haswell, intel_ddi_init
then tries to use the freed encoder on the HDMI initialization path
since the following commit:
commit 21a8e6a485
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 10 23:28:35 2013 +0200
drm/i915: don't setup hdmi for port D edp in ddi_init
So now on intel_ddi_init we check for the "ghost eDP" case and return
without trying to initialize HDMI. This way we won't try to read the
freed "intel_encoder" struct in the next "if" statement.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because intel_dp_init_connector is too big for my poor little brain.
No functional changes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By the time we call intel_dp_destroy (which destroys the connector)
the encoder may have been destroyed already, so if we use it we may be
reading some free memory. That happens in drm_mode_config_cleanup()
and also inside intel_dp_init_connector() when we detect a ghost eDP.
I also hope this may solve some random memory bugs.
Reported by kmemcheck.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for exynos5420 mixer IP in the drm mixer driver.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds new combatible strings for hdmi, mixer, ddc
and hdmiphy. It follows the convention of using compatible string
which represent the SoC in which the IP was added for the first
time.
Drivers continue to support the previous compatible strings
but further addition of these compatible strings in device tree
is deprecated.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Modified code for calculating hdmi IP register values from drm timing
values. The modification is based on the inputs from hw team and specifically
proposed for 1440x576i and 1440x480i. But same changes holds good for other
interlaced resolutions also.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Cleanup by removing flags variable from drm_hdmi_dt_parse_pdata
which is not used anywhere. Swtiching to of_get_named_gpio instead
of of_get_named_gpio_flags solved this.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Seung-Woo Kim <sw0312@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
vm_mmap function returns unsigned long so addr type should be unsigned long.
a pointer or address variable is required to use unsigned long or uint64_t
type for 64bits address support.
So this patch makes sure that addr has unsigned long type and also
exynos_drm_gem_mmap_ioctl returns correct error type.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
HDMI driver needs to configure the mout_hdmi mux clock to change
the parent between sclk_hdmiphy and sclk_pixel.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Change the clk_enable/clk_disable calls in mixer and hdmi drivers into
clk_prepare_enable/clk_disable_unprepare, respectively.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch cleans up logs for DRM_ERROR / DRM_DEBUG_KMS to avoid
logging duplicated function name because the macros already contain
__func__.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch removes tracking log functions which were used to debug
in the early development stage and are not so important as were.
So remove them for code clean up.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch renames check_timing to check_mode and removes the
unnecessary conversion of drm_display_mode to/from fb_videomode in
the hdmi driver.
v4:
1) Changed the commit message to add information related to renaming
the callbacks to check_mode.
2) Changed debug message to print 1/0 for interlace mode.
v3:
1) Replaced check_timing callbacks with check_mode.
2) Change the type of second parameter of check_mode callback from void
pointer paramenter to struct drm_display_mode pointer.
v2:
1) Removed convert_to_video_timing().
2) Corrected DRM_DEBUG_KMS to print the resolution properly.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The FIMD block present on S3C6400/S3C6410 SoCs is compatible with this
driver, so it can be supported by it as well.
This patch adds appropriate device IDs and driver data to enable this
driver for S3C64xx SoCs.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Some platforms that can be supported this driver has additional clock
source selection bits in VIDCON0 register that allows to select which
clock should be used to drive the pixel clock: bus clock or special
clock.
Since this driver assumes that special clock always drives the pixel
clock, this patch sets the selection bitfield to use the special clock.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Some platforms that can be supported with this driver have PRTCON
register instead of SHADOWCON, which requires slightly different
handling.
This patch factors out all register shadow control code from the driver
and adds a function to control register shadowing appropriately,
depending on driver data.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds pointer to driver data to fimd_context structure, to
remove the need to call drm_fimd_get_driver_data() each time access to
driver data is necessary.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds exynos_drm_crtc_mode_set_commit function
to update mode data and it makes page flip call this function
instead of calling exynos_drm_crtc_mode_set_base function directly.
exynos_drm_crtc_mode_set_base function is called by drm subsystem
as a callback so we don't have to call this function directly.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
'mixer_match_types' is always compiled in. Hence of_match_ptr is not
necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The definition of regulator_bulk_enable is fixed with __must_check
and this causes following build warning.
warning: ignoring return value of 'regulator_bulk_enable',
declared with attribute warn_unused_result
This patch fixes to check return value of the function.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch just checks if win_data array range is valid
or not correctly.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Valid values for FIMD windows are from 0 to WINDOWS_NR-1
inclusive (5 windows in total). The WINDOWS_NR is also
a size of fimd_context.win_data array.
However, early-return tests for wrong values of windows
accepted a value of WINDOWS_NR which is out of bound
for fimd_context.win_data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Valid values for mixer window are from 0 to MIXER_WIN_NR-1 inclusive.
Arrays in structures (e.g. mixer_context.win_data) have size of
MIXER_WIN_NR so checks for wrong mixer window must be greater-equal.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Hyunhee Kim <hyunhee.kim@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This reverts commit 160954b7bc.
This was rearming the workqueue with a 0 timeout, causing
a WARN_ON, and possible loop.
Daniel writes:
"I've looked a bit into this and I think we need to have a separate
work struct for recovering these lost hotplug events since the
continuous self-rearming case is a real risk (e.g. if a connector
flip-flops all the time). At least I don't see a sane way to block out
re-arming with the current code in a simple way. So reverting the
offender seems like the right thing and I'll go back to the drawing
board for 3.12."
Signed-off-by: Dave Airlie <airlied@redhat.com>
The dma_buf_fd() can return error when it fails to prepare fd,
so the dma_buf needs to be put.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When drm_prime_add_buf_handle() returns failure for an exported
dma_buf, the dma_buf was already allocated and its refcount was
increased, so it needs to be put.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drm prime also can support it like GEM CMA supports to cache
mapping. It doesn't allow multiple mappings for one attachment.
[airlied: rebased on top of other prime changes]
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of NULL, error value is casted with ERR_PTR() for
drm_prime_pages_to_sg() and IS_ERR_OR_NULL() macro is replaced
with IS_ERR() macro for drm_gem_map_dma_buf().
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The dma_map_sg(), in map_dma_buf callback operation of prime helper,
can return 0 when it fails to map, so it needs to release related
resources.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If idr_alloc() is failed, obj->name can be error value. Also
it cleans up duplicated flink processing code.
This regression has been introduced in
commit 2e928815c1
Author: Tejun Heo <tj@kernel.org>
Date: Wed Feb 27 17:04:08 2013 -0800
drm: convert to idr_alloc()
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drm_gem_mmap_obj() has to be protected with dev->struct_mutex,
but some caller functions do not. So it adds mutex lock to missing
callers and adds assertion to check whether drm_gem_mmap_obj() is
called with mutex lock or not.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This ends up causing circularity and really let people shoot themselves
in the foot.
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Try to use lockdep_assert_held or other alternatives where possible.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that the code is compatible in semantics, flip the switch.
Use ww_mutex instead of the homegrown implementation.
ww_mutex uses -EDEADLK to signal that the caller has to back off,
and -EALREADY to indicate this buffer is already held by the caller.
ttm used -EAGAIN and -EDEADLK for those, respectively. So some changes
were needed to handle this correctly.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
cli->mutex was inverted with reservations, and multiple reservations were
used without a ticket, fix both. This commit had to be done after the previous
commit, because otherwise ttm_eu_* calls would use a different seqno counter..
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit converts the source of the val_seq counter to
the ww_mutex api. The reservation objects are converted later,
because there is still a lockdep splat in nouveau that has to
resolved first.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Mutexes should not be acquired in interrupt context. While the trylock
fastpath is arguably safe on all implementations, the slowpath
unlock path definitely isn't.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Mutexes should not be acquired in interrupt context. While the trylock
fastpath is arguably safe on all implementations, the slowpath
unlock path definitely isn't.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Having nouveau builtin would still allow ACPI_VIDEO to be used as external module
if some of the deps for acpi_video have not been met, which would result in a linking
failure. Solve this by selecting all dependencies as well.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Shouldn't happen, and we invert the struct_mutex with reservation here,
potentially leading to deadlocks. Once reservations become lockdep annotated,
lockdep will go splat on this.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add missing calls, and fix a leak from forgetting to call the unpin function.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is the pull request for radeon for 3.11. Highlights include:
- Support for CIK (Sea Islands) asics: 3D, compute, UVD
- DPM (Dynamic Power Management) support for 6xx-SI
- ASPM support for 6xx-SI
- Assorted bug fixes
* 'drm-next-3.11' of git://people.freedesktop.org/~agd5f/linux: (168 commits)
drm/radeon/SI: fix TDP adjustment in set_power_state
drm/radeon/NI: fix TDP adjustment in set_power_state
drm/radeon: fix endian issues in atombios dpm code
drm/radeon/dpm: fix UVD clock setting on SI
drm/radeon/dpm: fix UVD clock setting on cayman
drm/radeon/dpm: add support for setting UVD clock on rv6xx
drm/radeon/dpm: add support for setting UVD clock on rs780
drm/radeon: fix typo in ni_print_power_state
drm/radeon: fix typo in cik_select_se_sh()
drm/radeon/si: fix typo in function name
drm/radeon/dpm: fix typo in setting uvd clock
drm/radeon/dpm: add dpm_set_power_state failure output (si)
add dpm_set_power_state failure output (7xx-ni)
drm/radeon/dpm: add dpm_set_power_state failure output (7xx-ni)
drm/radeon/dpm: add dpm_enable failure output (si)
drm/radeon/dpm: add dpm_enable failure output (7xx-ni)
drm/radeon/kms: add dpm support for SI (v7)
drm/radeon: switch SI to use radeon_ucode.h
drm/radeon: add SI to r600_is_internal_thermal_sensor()
drm/radeon/dpm/rs780: properly catch errors in dpm setup
...
Last 3.11 feature pull. I have a few odds bits and pieces and fixes in my
queue, I'll sort them out later on to see what's for 3.11-fixes and what's
for 3.12. But nothing to hold this here up imo.
Highlights:
- more hangcheck work from Mika and Chris to prepare for arb robustness
- trickle feed fixes from Ville
- first parts of the shared pch pll rework, with some basic hw state
readout and cross-checking (this shuts up the confused pch pll refcount
WARN that Linus just recently forwarded)
- Haswell audio power well support from Wang Xingchao (alsa bits acked by
Takashi)
- some cleanups and asserts sprinkling around the plane/gamma enabling
sequence from Ville
- more gtt refactoring from Ben
- clear up the adjusted->mode vs. pixel clock vs. port clock confusion
- 30bpp support, this time for real hopefully
* tag 'drm-intel-next-2013-06-18' of git://people.freedesktop.org/~danvet/drm-intel: (97 commits)
drm/i915: remove a superflous semi-colon
drm/i915: Kill useless "Enable panel fitter" comments
drm/i915: Remove extra "ring" from error message
drm/i915: simplify the reduced clock handling for pch plls
drm/i915: stop killing pfit on i9xx
drm/i915: explicitly set up PIPECONF (and gamma table) on haswell
drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
drm/i915: set up PIPECONF explicitly on ilk-ivb
drm/i915: find guilty batch buffer on ring resets
drm/i915: store ring hangcheck action
drm/i915: add batch bo to i915_add_request()
drm/i915: change i915_add_request to macro
drm/i915: add i915_gem_context_get_hang_stats()
drm/i915: add struct i915_ctx_hang_stats
drm/i915: Try harder to disable trickle feed on VLV
drm/i915: fix up pch pll enabling for pixel multipliers
drm/i915: hw state readout and cross-checking for shared dplls
drm/i915: WARN on lack of shared dpll
drm/i915: split up intel_modeset_check_state
drm/i915: extract readout_hw_state from setup_hw_state
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_fb.c
drivers/gpu/drm/i915/intel_sdvo.c
This adds dpm support for SI asics. This includes:
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2/gen3 switching
- power containment
- shader power scaling
Set radeon.dpm=1 to enable.
v2: enable hainan support, rebase
v3: guard acpi stuff
v4: fix 64 bit math
v5: fix 64 bit div harder
v6: fix thermal interrupt check noticed by Jerome
v7: attempt fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These changes are mostly minor fixes to things introduced in 3.10. The
biggest chunk is updates to the host1x firewall which checks job
submissions from userspace and wasn't working properly. All other
patches are mostly one-liners. Nothing new or too exciting this time
around.
* 'drm/for-next' of git://anongit.freedesktop.org/tegra/linux:
gpu: host1x: Rework CPU syncpoint increment
gpu: host1x: Fix client_managed type
gpu: host1x: Fix memory access in syncpt request
gpu: host1x: Copy gathers before verification
gpu: host1x: Don't reset firewall between gathers
gpu: host1x: Check reloc table before usage
gpu: host1x: Check INCR opcode correctly
drm/tegra: Remove DRIVER_BUS_PLATFORM from driver_features
drm/tegra: Fix return value
drm/tegra: Include header drm/drm.h
MAINTAINERS: Update Tegra DRM entry
drm/tegra: fix error return code in gr2d_submit()
drm/tegra: fix missing unlock on error
drm/tegra: Honor pixel-format changes
drm/tegra: Explicitly set irq_enabled
drm/tegra: Don't disable unused planes
Add a helper function to determine the preferred
pcie gen based on the card, system, and circumstance.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Validate the voltages against the voltage requirements of the
dispclk. We currently don't adjust the disp clock so it never
changes, but we need to filter out voltage levels that are too
low none the less.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If both the motherboard and GPU support pcie gen2 or 3,
enable it. PCIE gen2 and 3 offer more bandwidth than
pcie gen1.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There's a new table for calculating the memory pll
parameters on SI. Required for SI DPM support.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that the proper fix has been implemented I can
remove the last remnants of the initial implementation.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This properly implemented dynamic state adjustment by
using a working copy of the requested and current
power states.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This properly implemented dynamic state adjustment by
using a working copy of the requested and current
power states.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This properly implemented dynamic state adjustment by
using a working copy of the requested and current
power states.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This properly implemented dynamic state adjustment by
using a working copy of the requested and current
power states.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for cayman asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching (requires additional acpi support)
- power containment
- shader power scaling
Set radeon.dpm=1 to enable.
v2: fold in tdp fix
v3: fix indentation
v4: fix 64 bit div
v5: attempt to fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Use a dedicated copy of the current power state since
we may have to adjust it on the fly.
v2: fix up redundant state sets
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
