This lets one have a clue that maybe timeouts are happening
when we just aren't waiting long enough.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When testing a 9888 chipset NIC, I notice it often takes
almost 2 seconds, and then many times OTP fails, probably due
to the two-second timeout.
[ 2269.841842] ath10k_pci 0000:05:00.0: bmi cmd took: 1984 jiffies (HZ: 1000), rv: 0
[ 2273.608185] ath10k_pci 0000:05:00.0: bmi cmd took: 1986 jiffies (HZ: 1000), rv: 0
[ 2277.294732] ath10k_pci 0000:05:00.0: bmi cmd took: 1989 jiffies (HZ: 1000), rv: 0
So, increase the BMI timeout to 3 seconds.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reverts commit b057886524 ("ath10k: do not use coherent memory for
allocated device memory chunks") in 2015 which converted this allocation from
dma_map_coherent() to kzalloc() / dma_map_single().
The current problem manifests when using later model NICs with larger
(>700KiB) scratch spaces in memory. Although the kzalloc call
succeeds, the software IOMMU TLB code (via dma_map_single()) panics
because it can't find 700KiB of linear physmem bounce buffers for DMA.
Now, this is a bit of a silly failure mode for the dma map API,
but it's what we currently have to play with.
In these cases, doing kzalloc() works fine, but the dma_map_single()
call fails.
After chatting with Linus briefly about this, it indeed should be
using dma_alloc_coherent() for doing larger device memory allocation
that requires some kind of physical address mapping.
You're not supposed to be using kzalloc and dma_map_* calls for
large memory regions, and I'm guessing not for long-held mappings
either. Typically dma mappings should be temporary for DMA,
not long held like these.
Now, since hopefully the major annoying underlying problem has also been
addressed (ie, ath10k is no longer tears down all of these allocations
and reallocates them every time the vdevs are brought down) fragmentation
should stop being such a touchy issue. If it is though, using
dma_alloc_coherent() use gets us access to the CMB APIs too relatively
easily and ideally we would be allocating memory early in boot for
exactly these reasons.
Signed-off-by: Adrian Chadd <adrian@FreeBSD.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA4019 firmware 10.4-3.2.1-00050 reports only HT MCS rates between
0-9. But 802.11n MCS rates can be larger than that. For example a 2x2
device can send with up to MCS 15.
The firmware encodes the higher MCS rates using the NSS field. The actual
calculation is not documented by QCA but it seems like the NSS field can be
mapped for HT rates to following MCS offsets:
* NSS 1: 0
* NSS 2: 8
* NSS 3: 16
* NSS 4: 24
This offset therefore has to be added for HT rates before they are stored
in the rate_info struct.
Fixes: cec17c3821 ("ath10k: add per peer htt tx stats support for 10.4")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The array fields in struct wmi_start_scan_arg that are checked here are
fixed size arrays so they can never be NULL.
Addresses-Coverity-ID: 1260031
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9xxx and QCA61x4/QCA93xx are using different wmi operation, in order
for userspace to differentiate it, appends the wmi_op_version information
alone with the get_version command.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During write to debugfs file simulate_fw_crash, fixed-size local buffer
'buf' is accessed and modified at index 'count-1', where 'count' is the
size of the write (so potentially out of bounds).
This patch fixes this problem.
Signed-off-by: Michael Mera <dev@michaelmera.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipsets like QCA6584 have support for SDIO so add initial SDIO bus support to
ath10k. With this patch we have the low level HTC protocol working and it's
possible to boot the firmware, but it's still not possible to connect or
anything like. More changes are needed for full functionality. For that reason
we print during initialisation:
WARNING: ath10k SDIO support is incomplete, don't expect anything to work!
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[kvalo@qca.qualcomm.com: refactoring, cleanup, commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since both SDIO based chipsets will use different
firmware from the PCIe and AHB chipsets, the fw file name
must be different depending on bus type.
The new firmware names are:
For PCIe and AHB:
firmware-<api_version>.bin (same as before)
For SDIO:
firmware-sdio-<api_version>.bin
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added support for extended ready message.
The extended ready message contains the maximum bundle
count supported by SDIO chipsets.
It is transmitted by SDIO chipset only and replaces the
"standard" ready message in this case.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Special BMI get target info function for SDIO.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Extra initializations needed by all sdio boards.
Derived from qcacld.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Debug masks for SDIO HIF layer.
Address definitions for SDIO/mbox based chipsets.
Augmented struct host_interest with more members.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Code refactorization:
Moved the code for ep 0 in ath10k_htc_rx_completion_handler
to ath10k_htc_control_rx_complete.
This eases the implementation of SDIO/mbox significantly since
the ep_rx_complete cb is invoked directly from the SDIO/mbox
hif layer.
Since the ath10k_htc_control_rx_complete already is present
(only containing a warning message) there is no reason for not
using it (instead of having a special case for ep 0 in
ath10k_htc_rx_completion_handler).
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch moves the HTC ctrl service connect from
htc_wait_target to htc_init.
This is done in order to make sure the htc ctrl service
is setup properly before hif_start is called.
The reason for this is that we want the HTC ctrl service
callback to be initialized before the target sends the
HTC ready message.
The ready message will always be transmitted on endpoint 0
(which is always assigned to the HTC control service) so it
makes more sense if HTC control has been connected before the
ready message is received.
Since the service to pipe mapping is done as a part of
the service connect, the get_default_pipe call is redundant
and was removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The RX trailer parsing is now capable of parsing lookahead reports.
A lookahead contains the first 4 bytes of the next HTC message
(that will be read in the next SDIO read operation).
Lookaheads are used by the SDIO/mbox HIF layer to determine if
the next message is part of a bundle, which endpoint it belongs
to and how long it is.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Changed ath10k_htc_notify_tx_completion and
ath10k_htc_process_trailer from static to non static.
These functions are needed by SDIO/mbox.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This field will need to be used again for HE, so rename it now.
Again, mostly done with this spatch:
@@
expression status;
@@
-status->vht_nss
+status->nss
@@
expression status;
@@
-status.vht_nss
+status.nss
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY+cipAAoJEG4XJFUm622b+04H/2u7zhIqv3R5NsmGRlwjKmvd
6us1hcYzUiBW1kBFFtcvokwgqv3Rw/EUi+NYA5UCHgo30HTVJWTqW0q+BUEI7U0X
iwuFdHbs/qjj8hXKgZwaJMVyRhXAbq+iHYaMY5OEDNTRSbxqXA4V69SHGK9vLX0l
KQLJBZX3etnwsyRWrmd4E0roGGfD5tMPpGMUDSlvTPWt0I+1QFUxRI9ohn1fRBpD
p+UHHC+SYF6NzxvfqyPwm6ndb2XOwdAKYljlf4KrBwHtSXvAH8p5EASm4PjGbavY
0mrkv0cb8QOKQNVe9q4B4AmM4iAITZ9i3sQBPJ+EBN2P+kS/lFU5L/+5z3VQjms=
=KTEG
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-04-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
-----BEGIN PGP SIGNATURE-----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=f4VT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
My last pull request has been a while, we now have:
* connection quality monitoring with multiple thresholds
* support for FILS shared key authentication offload
* pre-CAC regulatory compliance - only ETSI allows this
* sanity check for some rate confusion that hit ChromeOS
(but nobody else uses it, evidently)
* some documentation updates
* lots of cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.12. Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
For QCA6174 hw3.0, since WLAN.RM.4.4-00022-QCARMSWPZ-2, it starts to
support the board ID information from otp, with some devices released on
the market that didn't calibrated with OTP, will have 0 for board ID
information, which cause the backward compatibility issue and was fixed
in commit 'd2e202c06ca4 ("ath10k: ignore configuring the incorrect board_id")'
So bump the fw api version to differentiate the latest firmware support.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
spectral_bin length (number of bins per fft sample) is usually
a value where (2^n = value), n is an integer. All of the QCA99X0
family of chipsets seems to report a spectral_bin length of
2^n + 'm' bytes, where m = 4, 12 based on the chipset. This 'm'
bytes seems to carry some radar related info which is currently
discarded only for 'bin_len = 68' bytes. Extend this discarding of
irrelevant 'bin_len' for QCA9984, QCA9888, IPQ4019 as well by
introducing a hardware parameter 'spectral_bin_discard'. Also
for QCA988X based family of chipsets which doesn't seem to have this
issue and also for some of the hardware which I have not tested
like QCA6174/QCA9377 the existing behaviour is retained as it is.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 'ath10k_ce_alloc_pipe' the compile time sanity check to
ensure that there is sufficient buffers in CE4 for HTT Tx
MSDU descriptors, but this did not take into account of the
case with 'peer flow control' enabled, fix this.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Lots of bugfixes as usual but also some new features.
Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
rt2x00
* add support MT7620
mwifiex
* enable auto deep sleep mode for USB chipsets
brcmfmac
* add support for network namespaces (WIPHY_FLAG_NETNS_OK)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY55+nAAoJEG4XJFUm622bRUAIAJfCM5YFyh9Y/XV147JshdGi
xScDAgwIA1/o+iHfvTsjSH3/uoH3JhsiqfcXN7R80kyvG7HrUeXaebmUDgbBvOOj
FTMuytiD+xkgEKVjWIwtXUYqctyzQ8ofxIQJ2W5E9CbEYAZ43uEcXzdnhBKVaVuY
XPw59MF5vRGDDXTnTf4af4OC+L1QqwUqsyi4j7oMIfexieMGQxQL0JYOyHweCnCV
gMz/kTxAIcmC1yOiunu8VyU4kK8borW36wC7XEE3MOXhqSKnQjyhI/efA76AKX0j
O7sfEKCFlZU1xXQbkB9ecbKc2jyMefiE0gwLWWI5dwKhnUS2qQ6GS8ML+NMfV0g=
=B2X+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-04-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Lots of bugfixes as usual but also some new features.
Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
rt2x00
* add support MT7620
mwifiex
* enable auto deep sleep mode for USB chipsets
brcmfmac
* add support for network namespaces (WIPHY_FLAG_NETNS_OK)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate line
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix output from checkpatch.pl like:
Symbolic permissions 'S_IRUSR' are not preferred.
Consider using octal permissions '0400'.
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate lin
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch helps to fix TPC stats to display the stats
properly. Here cosmetic change has been done to print the
TPC stats for all the cases 1.CDD 2.STBC 3.TXBF
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove obselete Copy Engine comments referring to the function
ath10k_ce_sendlist_send as this function was removed long time back
by the commit 2e761b5a52 ("ath10k: remove ce_sendlist_send").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add an ath10k HTC debug message when insufficient tx credits
are available to send the WMI commands. This is very useful
in debugging issues like 'tx credit starvation' that could
possibly happen with multiclient setup with constant roaming
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It seems set_coverage_class_work is not cancelled anywhere,
though I could not find a crash/warning with this existing
design, its safer to cancel it during stop() and also before
restarting the hardware.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If station advertises diffferent NSS capabilities in Rx_mcs set
of HT and VHT IEs in assoc req, the current NSS computation
logic configures the NSS support only based on Rx_mcs set of
HT capabilities in the driver. This is configuring the station
NSS capabilities incorreclty in the target.
For example, if station advertise Rx_mcs set as 2 spatial streams
in HT capabilities and 1 spatial streams in VHT capabilities in
assoc request, as per current logic we are calculating nss from
HT capabilities and the driver sets peer_num_spatial_streams as
2 for the station which is configured in VHT 1*1.
This patchs fix this issue by calculating the nss from VHT cap if
station supports vht.
Signed-off-by: Venkateswara Rao Naralasetty <c_vnaral@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move NAPI enable to 'ath10k_ahb_hif_start' from
'ath10k_ahb_hif_power_up'. This is to maintain the symmetry
of calling napi_enable() from ath10k_ahb_hif_start() so that it
matches with napi_disable() being called from ath10k_pci_hif_stop().
This change is based on the crash fix from Kalle for PCI interface in
commit 1427228d58 ("ath10k: fix napi crash during rmmod when probe
firmware fails").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check of len > buf_len is redundant as len is initialized
to 0 and buf_len to 4096, so this comparison is always false.
Remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix typo (spelling mistake) in wmi.h
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
I failed to notice that commit 523f6701db ("ath10k: update available channel
list for 5G radio") added two new warnings:
drivers/net/wireless/ath/ath10k/mac.c:3129:6: warning: symbol 'ath10k_mac_update_channel_list' was not declared. Should it be static?
drivers/net/wireless/ath/ath10k/mac.c:3170: Alignment should match open parenthesis
Fix those.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the 'commit ebee76f7fa ("ath10k: allow setting coverage class")',
it inherits the design and the address offset from ath9k, but the address
is not applicable to QCA6174, which leads to a random crash while doing the
resume() operation, since the set_coverage_class.ops will be called from
ieee80211_reconfig() when resume() (if the wow is not configured).
Fix the incorrect address offset here to avoid the random crash.
Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2.
kvalo: this also seems to fix a regression with firmware restart.
Fixes: ebee76f7fa ("ath10k: allow setting coverage class")
Cc: <stable@vger.kernel.org> # v4.10
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fetch target operating channel during potential radar detection when
the interface is just brought up, but no channel is assigned from
userspace. In this scenario rx_channel may not be having a valid pointer
hence fetch the target operating channel to avoid warnings as below
which can be triggered by the commands with DFS testing over longer run
comamnds:
iw wlan1 set type mesh
ifconfig wlan1 up (valid tgt_oper_chan only)
iw wlan1 cac trigger freq 5260 HT20 (valid rx_channel, tgt_oper_chan)
iw wlan1 cac trigger freq 5280 HT20
iw wlan1 cac trigger freq 5300 HT20
Once the CAC expires, current channel context will be removed and
we are only left with the fallback option of using 'target operating
channel'
Firmware and driver log:
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath: phy1: DFS: radar found on freq=5260: id=5, pri=3151, count=6,
count_false=11
ath: phy1: DFS: radar found on freq=5280: id=1, pri=1351, count=6,
count_false=4
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
Call trace:
WARNING: CPU: 1 PID: 2145 at
backports-20161201-3.14.77-9ab3068/net/wireless/chan.c:265
cfg80211_set_dfs_state+0x3c/0x88 [cfg80211]()
Workqueue: phy1 ieee80211_dfs_radar_detected_work
[mac80211]
[<c0320770>] (warn_slowpath_null) from [<bf79b90c>]
(cfg80211_set_dfs_state+0x3c/0x88 [cfg80211])
[<bf79b90c>] (cfg80211_set_dfs_state [cfg80211]) from
[<bf79697c>] (cfg80211_radar_event+0xc4/0x140 [cfg80211])
[<bf79697c>] (cfg80211_radar_event [cfg80211]) from
[<bf83c058>] (ieee80211_dfs_radar_detected_work+0xa8/0xb4 [mac80211])
[<bf83c058>] (ieee80211_dfs_radar_detected_work
[mac80211]) from [<c0339518>] (process_one_work+0x298/0x4a4)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check on ret for an error is redundant because it is already been
checked for non-zero earlier on and ret is never non-zero at this point.
Fix this by removing the redundant check and error message.
Detected by CoverityScan, CID#1357170 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If a 5 GHz radio is calibrated for operation in both
the low band (channels 36 to 64) and high band(channels 100 to 169),
hardware allows operations in all the listed channels. However,
if the chip has been calibrated only for the low/high band and
a high/low band channel is configured, due to lack of calibration
there will be potentially invalid signal on those non calibrated channels.
To avoid this problem this patch sets IEEE80211_CHAN_DISABLED flag for
those non calibrated channels by using low_5ghz_chan and high_5ghz_chan
values which we get from target through wmi service ready event.
Driver initialized flags are getting re initialized in handle_channel
in cfg80211. So calling the function to disable the non supported channel
from reg_notifier().
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DFS is not enabled in hostapd (ieee80211h=0) DFS channels shall
not be available for use even though the hardware may have the capability
to support DFS. With this configuration (DFS disabled in hostapd) trying to
bring up ath10k device in DFS channel for AP mode fails and trying to
simulate DFS in ath10k debugfs results in a warning in cfg80211 complaining
invalid channel and this should be avoided in the driver itself rather than
false propogating RADAR detection to mac80211/cfg80211. Fix this by
checking for the first vif 'is_started' state(should work for client mode
as well) as all the vifs shall be configured for the same channel
sys/kernel/debug/ieee80211/phy1/ath10k# echo 1 > dfs_simulate_radar
WARNING: at net/wireless/chan.c:265 cfg80211_radar_event+0x24/0x60
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
WARNING: at net/wireless/nl80211.c:2488 nl80211_get_mpath+0x13c/0x4cc
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Doing a channel switch via hostapd_cli seems to update
the new channel context for each VAP's appropriately as below
in 'ath10k_mac_update_vif_chan', hence we can safely suppress the
warning that shows up during this operation and dump the warning only
if no vaps are available for channel switch
hostapd_cli -i wlan0 chan_switch 5 5200
OK
ath10k_pci : mac chanctx switch n_vifs 3 mode 1
ath10k_pci : mac chanctx switch vdev_id 2 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 1 freq 5180->5200 width 0->0
ath10k_pci : mac chanctx switch vdev_id 0 freq 5180->5200 width 0->0
Call Trace:
WARNING: backports-20161201-3.14.77-9ab3068/drivers/net/wireless/ath/ath10k/mac.c:7126
[<c022f2d4>] (warn_slowpath_null) from [<bf7f150c>]
(ath10k_reconfig_complete+0xe4/0x25c [ath10k_core])
[<bf7f150c>] (ath10k_reconfig_complete [ath10k_core])
[<bf7f35f0>] (ath10k_mac_vif_ap_csa_work+0x214/0x370 [ath10k_core])
[<bf7f38b8>] (ath10k_mac_op_change_chanctx+0x108/0x128 [ath10k_core])
[<bf782ac0>] (ieee80211_recalc_chanctx_min_def+0x30c/0x430 [mac80211])
[<bf7830a4>] (ieee80211_recalc_smps_chanctx+0x2ec/0x840 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context+0x7c/0xf8 [mac80211])
[<bf7843e8>] (ieee80211_vif_use_reserved_context [mac80211])
[<bf76e5d4>] (ieee80211_csa_finalize_work+0x5c/0x88 [mac80211])
Fixes: d7bf4b4aba ("ath10k: fix ar->rx_channel updating logic")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9377 is the family of QCA61x4 which shared the same procedure
to enable the hardware clock that could improve the firmware download time.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Len Brown reported the system resume time is taking more than 2 seconds in
bug - https://bugzilla.kernel.org/show_bug.cgi?id=185621.
The reason of the 2 seconds is due to the firmware download time.
The chip is booted up in the default reference clock speed to handle the
firmware download to chip memory and advanced to the support higher speed
clock to run the firmware after all. The default reference clock in the
hardware is slow so that the firmware download time is taking up to 2
seconds for a 600KB firmware file.
[76796.349701] ath10k_pci : boot uploading firmware image len 688691
[76798.334612] ath10k_pci : htt tx max num pending tx 1056
The resolution here is to enable the higher speed clock if the hardware
supported before the firmware download at BMI stage, so that the hardware
can handle the firmare download in a more efficient way. This can help to
improve the firmware download time from 2 seconds to around 500ms for the
same 600KB firmware file.
[322858.577919] ath10k_pci boot uploading firmware image len 688691
[322859.093094] ath10k_pci htt tx max num pending tx 1056
The steps to advance to the higher speed clock is very hardware specific,
so adding the hardware ops for the hardware that can support this.
Reported-by: Len Brown <lenb@kernel.org>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set the NL80211_EXT_FEATURE_CQM_RSSI_LIST wiphy extended feature
wholesale in all mac80211-based drivers that do not set the
IEEE80211_VIF_BEACON_FILTER flags on their interfaces. mac80211 will
be processing supplied RSSI values in ieee80211_rx_mgmt_beacon and
will detect when the thresholds set by
ieee80211_set_cqm_rssi_range_config are crossed. Remaining (few)
drivers need code to enable the firmware to monitor the thresholds.
This is mostly only compile-tested.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
