This patch adds the digital loopback/bypass support for twl4030 codec.
The digital loopback will let the digimic0 (routed in the TX1 capture path
inside of TWL4030) data to be routed back to the RX2 playback path
(I2S stereo). It can also route the analog capture date routed through the
TX1 back to RX2.
Effectively the digital loopback is routing the audio from the TX1 capture path
to the RX2 playback path.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the WM8731 driver to use a more standard device registration
scheme where the device can be registered independantly of the ASoC
probe.
As a transition measure push the current manual code for registering
the WM8731 into the individual machine driver probes. This allows
separate patches to update the relevant architecture files with less
risk of merge issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a pure code motion patch intended to improve reviewability of a
following patch moving WM8731 to use more standard device registration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8731 bias level configuration function was written slightly
obscurely - streamline the code a little and refresh the comments.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
WM8753 uses a tricky way to switch DAIs "on the fly", for that it
registers 2 dummy DAIs and substitutes them depending on mixer control.
List element of registered dummy DAIs should be preserved to allow
unregistering of DAIs on module unload.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the CS4270 codec driver to allow applications to use the mixer to
control Digital Loopback, Soft Ramp, Zero Cross, Popguard, and Auto-Mute.
Soft Ramp, Zero Cross, and Auto-Mute are disabled by the driver when it first
initializes the hardware, but these features either don't work or interfere
with normal ALSA behavior. However, they can now be re-enabled by an
application if desired.
Remove CONFIG_SND_SOC_CS4270_HWMUTE and always allow ASoC to control the mute
bits. The driver previously and erroneously assumed that these bits
control only external muting circuitry, but they also control internal
muting circuitry, so they should always be used.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
TLV320AIC3X volume controls are logarithmic. Export their dB ranges.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a minor fix but helps to define dB ranges for volume controls.
Only DAC digital volume has full register value range from 0 to 127 but
ADC PGA gain and output stage volume controls don't.
For ADC PGA, maximum value is 119 and then it saturates to the same
gain value of 59.5 dB. For output stages, value 117 corresponds to -78.3 dB
and is muted for values 118 and above.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Function wm899x_outpga_put_volsw_vu misuses the kcontrol's private value
by still accessing it as bitfields even SOC_SINGLE_VALUE constructs it
as a pointer into struct soc_mixer_control after the commit
4eaa9819dc.
This is very similar fix than fix to TLV320AIC3X codec made by
Eero Nurkkala <ext-eero.nurkkala@nokia.com>. This fix is compile tested
only.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Function snd_soc_dapm_put_volsw_aic3x misuses the kcontrol's private value
by still accessing it as bitfields even SOC_SINGLE_VALUE constructs it
as a pointer into struct soc_mixer_control after the commit
4eaa9819dc.
This was causing arbitrary register writes when touching the controls
defined with SOC_DAPM_SINGLE_AIC3X.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch splits set_dai_fmt into three variants (single interface,
dual interface playback only, dual interface capture only) so that
data input and output formats can be configured separately for dual
interface setups.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without this fix driver switches to WSPLL in uda1380_pcm_prepare
even if SYSCLK was chosen (uda1380_pcm_prepare modifies UDA1380_CLK
register to disable R00_DAC_CLK before flushing reg cache)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This just updates my email address on some drivers I'd forgotten in a
previous patch.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace printk calls with dev_xxx calls. Set the 'dev' field of the codec
and codec_dai structures so that these calls work.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix a oversight in the CS4270 codec driver that caused a build break.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Spruce up the documentation in the CS4270 codec. Use kerneldoc where
appropriate. Fix incorrect comments.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC codec drivers typically serve two masters: the I2C bus and ASoC itself.
When a codec driver registers with ASoC, a probe function is called. Most
codec drivers call ASoC first, and then register with the I2C bus in the ASoC
probe function.
However, in order to support multiple codecs on one board, it's easier if the
codec driver is probed via the I2C bus first. This is because the call to
i2c_add_driver() can result in the I2C probe function being called multiple
times - once for each codec. In the current design, the driver registers
once with ASoC, and in the ASoC probe function, it calls i2c_add_driver().
The results in the I2C probe function being called multiple times before the
driver can register with ASoC again.
The new design has the driver call i2c_add_driver() first. In the I2C probe
function, the driver registers with ASoC. This allows the ASoC probe function
to be called once per I2C device.
Also add code to check if the I2C probe function is called more than once,
since that is not supported with the current ASoC design.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the analog loopback/bypass support for twl4030 codec.
Details for the implementation:
It seams that the analog loopback needs the DAC powered on on the channel,
where the loopback is selected. The switch for the DACs has been moved from
the DAPM_DAC to the "Analog XX Playback Mixer". In this way the DAC will be
powered while the audio playback is used or/and the loopback is enabled for
the channel.
The twl4030 codec powering has been reworked. Now the codec will be powered as
long as it does not receives the SND_SOC_BIAS_OFF event. The exceptions are
when the given change in the registers needs the codec power down/up cycle in
order to take effect. Otherwise the codec is on.
When the codec enters to STANDBY state and none of the loopback paths are
enabled, than the amplifiers, which are no in the DAPM path are forced to turn
off and the PLL is disabled. When playback/capture starts the disabled gains
are restored and the PLL is enabled.
When one of the loopback enabled in STANDBY mode, the disabled gains are
restored and the PLL is enabled also.
In short: the codec always goes to the lowest power state based on the
bias_level and the bypass_state.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8753 driver multiplexes the DAI structures it exposes to the
outside world, leaving them uninitialised until the codec probes. Since
the DAI name is used during the registration and setup process provide a
dummy name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the twl4030_power_up and twl4030_power_down function
earlier to facilitate the analog bypass implementation.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the power switches for the physical ADC and for the
amplifiers for the analog capture path to map more closely
the actual path inside of the codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Headset Left anti-pop and bias ramp does not need to be
enabled, if the headset is not in use.
Move the code to DAPM event handler for HeadsetL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge the codec up and down functions to a simple one.
Codec is powered down by default (reg_cache change).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The offset cancelation bit in ANAMICL register is self cleanig.
Make sure that the reg_cache holds the same value as the HW
register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Further improvements in the I2C initialization sequence of the CS4270 driver.
All ASoC initialization is now done in the I2C probe function.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensures that the DAI and socdev exported by the codec match up with
their exported prototype.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kbuild ignores dependency from things that are themselves selected so
ASoC machine drivers need to ensure that the control bus is being built.
This also avoids issues where multiple buses are supported by a given
codec.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The CS4270 supports stand-alone mode, where the codec is not connect to the
I2C or SPI buses. Instead, input voltages configure the codec at power-on.
The CS4270 ASoC device driver has partial support for this mode, but the
code was never tested, and partial support doesn't help anyone. It also made
the rest of the code more complicated than necessary.
[Removed redundant CS4270 dependency on I2C -- broonie]
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes the acpture switch name so that it better reflects its
purpose.
Signed-off-by: Ian Molton <iann@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch takes fixes a number of bugs in the caching code used by
several ASoC codec drivers. Mostly off-by-one fixes.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM9713 driver does not support configuring the PLL output frequency
so the output frequency parameter is irrelevant. Allow users to set it
to zero by ignoring it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver adds support for the wm9705 ac97 codec. The driver supports
audio input and output.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Call the snd_soc_free_pcm and snd_soc_dapm_free when the
codec driver is unloaded.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many codec drivers were implementing cookie-cutter copies of the function
that adds kcontrols to the codec.
This patch moves this code to a common function snd_soc_add_controls() in
soc-core.c and updates all drivers using copies of this function to use the
new common version.
[Edited to raise priority of error log message and document parameters.
-- broonie]
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The soc_value_enum has been merged to soc_enum.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For codecs that have both SPI and I2C support we need to ensure that we
don't try to make the codec driver built in when I2C is modular since
that won't link. Do this by creating a helper variable which uses
conditional defaults to pick up the correct value for all combinations.
We don't need to do anything special for I2C-only codecs since a
conditional select passes on the full value for a tristate.
Reported-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert the bitfield coded enums to the new VALUE_ENUM type.
Remove the enum check, since the VALUE_ENUM type can handle
the bitfield coding and also handles the 'holes' in the bitfield.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds DAPM implementaion for the capture path
on twlx030.
TWL has two physical ADC and two digital microphone (stereo) connections.
The CPU interface has four microphone channels.
For simplicity the microphone channel paths are named as:
TX1 (Left/Right) - when using i2s mode, only the TX1 data is valid
TX2 (Left/Right)
Input routing (simplified version):
There is two levels of mux settings for TWL in input path:
Analog input mux:
ADCL <- {Off, Main mic, Headset mic, AUXL, Carkit mic}
ADCR <- {Off, Sub mic, AUXR}
Analog/Digital mux:
TX1 Analog mode:
TX1L <- ADCL
TX1R <- ADCR
TX1 Digital mode:
TX1L <- Digimic0 (Left)
TX1R <- Digimic0 (Right)
TX2 Analog mode:
TX2L <- ADCL
TX2R <- ADCR
TX2 Digital mode:
TX2L <- Digimic1 (Left)
TX2R <- Digimic1 (Right)
The patch provides the following user controls for the capture path:
Mux settings:
"TX1 Capture Route": {Analog, Digimic0}
"TX2 Capture Route": {Analog, Digimic1}
"Analog Left Capture Route": {Off, Main Mic, Headset Mic, AUXL, Carkit Mic}
"Analog Right Capture Route": {Off, Sub Mic, AUXR}
Volume/Gain controls:
"TX1 Digital Capture Volume": Stereo gain control for TX1 path
"TX2 Digital Capture Volume": Stereo gain control for TX2 path
"Analog Capture Volume": Stereo gain control for the analog path only
Important things for the board files:
Microphone bias:
"Mic Bias 1": Bias for Main mic or for digimic0 (analog or digital path)
"Mic Bias 2": Bias for Sub mic or for digimic1 (analog or digital path)
"Headset Mic Bias": Bias for Headset mic
When the routing configured correctly only the needed components will be
powered/enabled.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modify the enum filter to more generic that it will filter
out the enums with text "Invalid".
The enum filter also required for the capture path.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Thanks to Troy Kisky <troy.kisky@boundarydevices.com> for noticing.
- DSP_A format has 1-bit data delay which corresponds to SSM6202 submode 2
- DSP_B has 0-bit data delay which corresponds to submode 1
- Currently driver sets them opposite so swap the submode setting
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
