Use tcb0 for timers as selected in sama5_defconfig.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As the board have the proper pull-ups soldered on the data
and CMD lines we don't need them specified in the PADs. So remove
the "bias-pull-up" property and set "bias-disable".
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[claudiu.beznea@microchip.com: change subject to match the desired prefix]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
CAN0 is not connected on the sama5d27_som1_ek board, so remove
it from DT.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[claudiu.beznea@microchip.com: change subject to match the desired prefix]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add pin muxing for pwm0 and set it as disabled since it is in conflict
with the pins for leds.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Set the USER button as a wakeup source to allow wakeup from ULP0.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[claudiu.beznea@microchip.com: change subject to match the desired prefix]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Overwrite sama5d2.dtsi aliases node to match the at91-sama5d27_som1_ek
board configuration. ttyS0 stands for DBGU, ttyS1 for the mikro BUS 1
serial lines and ttyS2 for the mikro BUS 2 serial lines.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[claudiu.beznea@microchip.com: change subject to match the desired prefix]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add disabled statuses for all devices and for those those which pins
are in conflict with other devices add a comment in the DT file to specify
this.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The USB host has 3 ports so we must specify the entries for each
in the atmel,vbus-gpio property.
The specified pin (PA27) is the vbus for USBB and not USBA.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[claudiu.beznea@microchip.com: change subject to match the desired prefix]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fix typos that prevent proper using of uart2 and uart4 devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
There are some changes from the prototype board concerning LEDs and USB
pins:
- USBB power enable and red LED pins are inverted.
- The polarity of LEDs is inverted too.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>