Casting away const is bad practice. Since this is ARM specific driver
don't have hardware actually test this.
Having getter functions for ops is really unnecessary code bloat, but
not going to touch that.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After resume from hibernate on arm64, any amd-xgbe devices that were
running when we hibernated are reported as down, even when it is not.
Re-plugging the cables does not cause the interface to come back, the
link must be marked as down then up via 'ip set link' using the serial
console.
This happens because the device has been power-cycled and possibly
re-initialised by firmware, whereas the driver's memory structures have
been restored from the hibernate image and the two do not agree.
Schedule a restart of the device after powerup in case the world changed
while we were asleep.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i has been defined as unsigned int.
So use %u for output.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
There was a check on CAP_NET_ADMIN in au1000_set_settings, but this
check is already done in dev_ethtool, so no need to repeat it before
calling the generic function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7f854420fb
("phy: Add API for {un}registering an mdio device to a bus.")
broke PHY detection on this driver with a copy-paste bug:
The code is looking 32 times for a PHY at address 0.
Fixes ethernet on AMD DB1100/DB1500/DB1550 boards which have
their (autodetected) PHYs at address 31.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7f854420fb
("phy: Add API for {un}registering an mdio device to a bus.")
broke PHY detection on this driver with a copy-paste bug:
The code is looking 32 times for a PHY at address 0.
Fixes ethernet on AMD DB1100/DB1500/DB1550 boards which have
their (autodetected) PHYs at address 31.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(a && a > 0) is equivalent to (a > 0).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These drivers already call netif_stop_queue() so we should not be called
unless tx space is available. Just free the skb and return TX_OK.
Followup patch will remove NETDEV_TX_LOCKED from the kernel.
Cc: linux-parisc@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: Thomas Sailer <t.sailer@alumni.ethz.ch>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure of kzalloc should cause the enclosing function
to return -ENOMEM, not -ENODEV.
Additionally, removed the following checkpatch warnings:
ERROR: spaces required around that '==' (ctx:VxV)
ERROR: space required before the open parenthesis '('
CHECK: Comparison to NULL could be written "!lp"
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the auto-negotiation interrupt handling disables the irq
instead of masking off the interrupts. This was done because the phy
library was originally used to read and write the PCS registers, which
could not be performed in interrupt context. Now that the phy library is
no longer used to read and write the PCS registers the interrupts can be
masked off in the interrupt service routine eliminating the need to call
disable_irq/enable_irq. This also requires changing the protection mutex
to a spinlock.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check to be sure that the Rx queue fifos are empty before stopping the
Rx DMA channels.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the netdev traffic class setup is only performed when invoked
through the ndo_setup_tc interface. However, the same setup should be
performed when the dcbnl interface (ieee_setets) is invoked. Rework the
netdev traffic class setup to be invokable through either interface and
also provide the priority to traffic class mapping if available.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is checking the pfc_en field of the ieee_pfc structure to
determine whether to associate a priority with a traffic class. This is
incorrect since the pfc_en field is for determining if PFC is enabled
for a traffic class.
The association of priority to traffic class does not depend on whether
the traffic class is enabled for PFC, so remove that check. Also, the
mapping of priorities to traffic classes should be done when configuring
the traffic classes and not the PFC support so move the priority to traffic
class association from xgbe_config_dcb_pfc to xgbe_config_dcb_tc.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the PFC flow control is enabled on all traffic classes if
one or more traffic classes request it. The PFC enable setting of the
traffic class should be used to determine whether to enable or disable
flow control for the traffic class.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using ethtool to set the speed for the device, verify that the
specified speed is valid within the active speedset.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change from calling __napi_schedule to __napi_schedule_irqoff when running
in interrupt context or when called by netpoll with interrupts already
disabled. The Tx timer function will continue to use __napi_schedule.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change from using napi_complete to napi_complete_done to allow for the
use of gro_flush_timeout in tuning network processing.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the hardware is placed in promiscuous mode it will still perform
VLAN filtering and therefore may not pass all packets to the driver.
Disable all VLAN filtering when entering promiscuous mode and restore
VLAN filtering upon exit from promiscuous mode. In order to avoid adding
forward declarations, move the VLAN related functions earlier in the
file.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.
This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The am79c961a.c driver fails to build with clang because of an
unusual inline assembly construct:
drivers/net/ethernet/amd/am79c961a.c:53:7: error: invalid % escape in inline assembly string
"str%?h %1, [%2] @ NET_RAP\n\t"
The same change has been done a decade ago in arch/arm as of
6a39dd6222 ("[ARM] 3759/2: Remove uses of %?"), but apparently
some drivers were missed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The warning about being able to read any MDIO device, not just the
attached ethernet devices PHY applies to all MDIO drivers. So remove
it. This also removes a reference to a member in phy_device which has
moved.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of the loop we test "if (!count)" but because "count--" is
a post-op then the loop will end with count set to -1. I have fixed
this by changing it to --count.
Fixes: c5aa9e3b81 ('amd-xgbe: Initial AMD 10GbE platform driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_set_dma_mask returns a negative errno value, not a bool like
pci_dma_supported. This of course was just a giant test for attention :)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Jongman Heo <jongman.heo@samsung.com>
Tested-by: Jongman Heo <jongman.heo@samsung.com> [pcnet32]
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.
skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().
Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Support for the ACPI _CCA configuration object intended to tell
the OS whether or not a bus master device supports hardware
managed cache coherency and a new set of functions to allow
drivers to check the cache coherency support for devices in a
platform firmware interface agnostic way (Suravee Suthikulpanit,
Jeremy Linton).
- ACPI backlight quirks for ESPRIMO Mobile M9410 and Dell XPS L421X
(Aaron Lu, Hans de Goede).
- Fixes for the arm_big_little and s5pv210-cpufreq cpufreq drivers
(Jon Medhurst, Nicolas Pitre).
- kfree()-related fixup for the recently introduced CPPC cpufreq
frontend (Markus Elfring).
- intel_pstate fix reducing kernel log noise on systems where
P-states are managed by hardware (Prarit Bhargava).
- intel_pstate maintainers information update (Srinivas Pandruvada).
- cpufreq core optimization related to the handling of delayed work
items used by governors (Viresh Kumar).
- Locking fixes and cleanups of the Operating Performance Points
(OPP) framework (Viresh Kumar).
- Generic power domains framework cleanups (Lina Iyer).
- cpupower tool updates (Jacob Tanenbaum, Sriram Raghunathan,
Thomas Renninger).
- turbostat tool updates (Len Brown).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJWQ96OAAoJEILEb/54YlRxyYYQALJ1HXu76SvYX1re2aawOw6Y
WgzF3Ly7JX034E1VvA2xP6wgkWpBRBDcpnRDeltNA4dYXPBDei/eTcRZTLX12N3g
AfFRGjGWTtLJfpNPecNMmUyF5xHjgDgMIQRabY+Is5NfP5STkPHJeqULnEpvTtx8
bd0lnC5jc4vuZiPEh1xVb+ClYDqWS8YQPyFJVjV/BaIf8Qwe5+oRX36byMBaKc9D
ZgmvmCk5n/HLQQ1uQsqe4xnhFLHN2rypt2BLvFrOtlnSz9VNNpQyB+OIW1mgCD4f
LhpKIwjP8NhZNQUq8HFu7nDlm8ciQtWmeMPB5NdGQ+OESu7yfKAOzQ+3U6Gl2Gaf
66zVGyV6SOJJwfDVJ3qKTtroWps9QV7ZClOJ+zJGgiujwU+tJ3pDQyZM9pa7CL3C
s7ZAUsI6IigSBjD3nJVOyG4DO0a8KQFCIE1mDmyqId45Qz8xJoOrYP33/ZnDuOdo
2OtL/emyfWsz9ixbHVfwIhb7EC6aoaUxQrhSWmNraaQS43YfioZR7h4we8gwenph
X4E1KY4SdML+uFf2VKIcd45NM3IBprCxx5UgFAJdrqe8+otqPNF2AVosG4iqhg/b
k4nxwuIvw2a8Fm77U9ytyXDYMItU/wIlAHMbnmgx+oTwRv6AbZ07MHkyfuQLYuhD
tq5Y14qSiTS7prNacx98
=XZiP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"The only new feature in this batch is support for the ACPI _CCA device
configuration object, which it a pre-requisite for future ACPI PCI
support on ARM64, but should not affect the other architectures.
The rest is fixes and cleanups, mostly in cpufreq (including
intel_pstate), the Operating Performace Points (OPP) framework and
tools (cpupower and turbostat).
Specifics:
- Support for the ACPI _CCA configuration object intended to tell the
OS whether or not a bus master device supports hardware managed
cache coherency and a new set of functions to allow drivers to
check the cache coherency support for devices in a platform
firmware interface agnostic way (Suravee Suthikulpanit, Jeremy
Linton).
- ACPI backlight quirks for ESPRIMO Mobile M9410 and Dell XPS L421X
(Aaron Lu, Hans de Goede).
- Fixes for the arm_big_little and s5pv210-cpufreq cpufreq drivers
(Jon Medhurst, Nicolas Pitre).
- kfree()-related fixup for the recently introduced CPPC cpufreq
frontend (Markus Elfring).
- intel_pstate fix reducing kernel log noise on systems where
P-states are managed by hardware (Prarit Bhargava).
- intel_pstate maintainers information update (Srinivas Pandruvada).
- cpufreq core optimization related to the handling of delayed work
items used by governors (Viresh Kumar).
- Locking fixes and cleanups of the Operating Performance Points
(OPP) framework (Viresh Kumar).
- Generic power domains framework cleanups (Lina Iyer).
- cpupower tool updates (Jacob Tanenbaum, Sriram Raghunathan, Thomas
Renninger).
- turbostat tool updates (Len Brown)"
* tag 'pm+acpi-4.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
PCI: ACPI: Add support for PCI device DMA coherency
PCI: OF: Move of_pci_dma_configure() to pci_dma_configure()
of/pci: Fix pci_get_host_bridge_device leak
device property: ACPI: Remove unused DMA APIs
device property: ACPI: Make use of the new DMA Attribute APIs
device property: Adding DMA Attribute APIs for Generic Devices
ACPI: Adding DMA Attribute APIs for ACPI Device
device property: Introducing enum dev_dma_attr
ACPI: Honor ACPI _CCA attribute setting
cpufreq: CPPC: Delete an unnecessary check before the function call kfree()
PM / OPP: Add opp_rcu_lockdep_assert() to _find_device_opp()
PM / OPP: Hold dev_opp_list_lock for writers
PM / OPP: Protect updates to list_dev with mutex
PM / OPP: Propagate error properly from dev_pm_opp_set_sharing_cpus()
cpufreq: s5pv210-cpufreq: fix wrong do_div() usage
MAINTAINERS: update for intel P-state driver
Creating a common structure initialization pattern for struct option
cpupower: Enable disabled Cstates if they are below max latency
cpupower: Remove debug message when using cpupower idle-set -D switch
cpupower: cpupower monitor reports uninitialized values for offline cpus
...
All drivers should be using dma_set_mask / pci_set_dma_mask to try to
set the dma mask instead of just querying it. Without that some iommu
implementations may not work.
pci_dma_supported is removed entirely, but dma_supported stays for
dma_ops implementations for now.
This patch (of 15):
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Fry <pcnet32@frontier.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Helge Deller <deller@gmx.de>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sergey Kozlov <serjk@netup.ru>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Steven Toth <stoth@kernellabs.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we have the new DMA attribute APIs, we can replace the older
acpi_check_dma() and device_dma_is_coherent().
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During Tx cleanup it's still possible for the descriptor data to be
read ahead of the descriptor index. A memory barrier is required between
the read of the descriptor index and the start of the Tx cleanup loop.
This allows a change to a lighter-weight barrier in the Tx transmit
routine just before updating the current descriptor index.
Since the memory barrier does result in extra overhead on arm64, keep
the previous change to not chase the current descriptor value. This
prevents the execution of the barrier for each loop performed.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
The code currently uses the lightweight dma_wmb barrier before updating
the current descriptor count. Under heavy load, the Tx cleanup routine
was seeing the updated current descriptor count before the updated
descriptor information. As a result, the Tx descriptor was being cleaned
up before it was used because it was not "owned" by the hardware yet,
resulting in a Tx queue hang.
Using the wmb barrier insures that the descriptor is updated before the
descriptor counter preventing the Tx queue hang. For extra insurance,
the Tx cleanup routine is changed to grab the current decriptor count on
entry and uses that initial value in the processing loop rather than
trying to chase the current value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous patch switched from using the system workqueue to the device
workqueue for various operations. During a device restart the device
workqueue is flushed so the restart cannot use this workqueue or else
a deadlock results. Move the device restart back to using the system
workqueue.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kasprintf function can return NULL if the allocation fails. Check for
successful allocation before attempting to use the returned buffer.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The XGBE_LINK bit is used just to determine whether to call the
netif_carrier_on/off functions. Rather than define and use this bit,
just call the functions. The netif_carrier_ok function can be used in
place of checking the XGBE_LINK bit in the future.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver creates, flushes and destroys a device workqueue but queues
work to the system workqueue. Switch from using the system workqueue to
the device workqueue.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
