Originally we would enable and disable the breadcrumb interrupt
immediately on demand. This was slow enough to have a large impact
(>30%) on tasks that hopped between engines. However, by using a shadow
to keep the irq alive for an extra interrupt (see commit 67b807a892
("drm/i915: Delay disabling the user interrupt for breadcrumbs")) and
by recently reducing the cost in adding ourselves to the signal tree, we
no longer need to spin-request during await_request to avoid delays in
throughput tests. Without the earlier patches to stop the wakeup when
signaling if the irq was already active, we saw no improvement in
execbuf overhead (and corresponding contention in other clients) despite
the removal of the spinner in a simple test like glxgears. This means
there will be scenarios where now we spend longer enabling the interrupt
than we would have spent spinning, but these are not likely to have as
noticeable an impact as the high frequency test cases (where there
should not be any regression).
Ulterior motive: generalising the engine->sync_to to handle different
types of semaphores and non-semaphores.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-4-chris@chris-wilson.co.uk
Enabling the interrupt for the signaler takes a finite amount of time (a
few microseconds) during which it is possible for the request to
complete. Check afterwards and skip adding the request to the signal
rbtree if it complete.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-3-chris@chris-wilson.co.uk
The important condition that we need to check after enabling the
interrupt for signaling is whether the request completed in the process
(and so we missed that interrupt). A large cost in enabling the
signaling (rather than waiters) is in waking up the auxiliary signaling
thread, but we only need to do so to catch that missed interrupt. If we
know we didn't miss any interrupts (because we didn't arm the interrupt)
then we can skip waking the auxiliary thread.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-2-chris@chris-wilson.co.uk
Setting up the irq to signal the request completion takes a finite
amount of time, during which it is possible that the request already
completed. Check afterwards, just in case, so that we can respond
immediately.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170608111405.16466-1-chris@chris-wilson.co.uk
And prevent calling i915_ggtt_disable_guc twice (the first when GuC init
failed, and the second time during driver unload / intel_uc_fini_hw),
and hitting the GEM_BUG_ON.
v2: Clear enable_guc_loading unconditionally (Michal)
Make sure guc_free_load_err_log is still called (Daniele)
Don't shoot the messenger (Chris)
Fixes: 3950bf3dbf ("drm/i915/guc: Add onion teardown to the GuC
setup")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170605171251.9905-1-michel.thierry@intel.com
Replace the large comment about requiring the powerwell for
intel_uncore_arm_unclaimed_mmio_detection() by moving the arming of the
mmio error detection into the powerwell held for modesetting. Thereby
also accomplishing the goal of only arming the mmio detection after a
full modeset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504115508.13571-1-chris@chris-wilson.co.uk
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch clean up a bit the platform definition block in
a way to avoid duplications and to let clear that GT3 for
the current platform only have the extra Media engine (BSD2).
v2: Kabylake IS_KABYLAKE as Anusha noticed.
v3: Avoid EXTRA_ENGINE_MASK and list rings out on GT3 to
make it more clear.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496765166-7068-1-git-send-email-rodrigo.vivi@intel.com
Let's be picky and just use PICK directly.
So we can extend this later without creating
a new PORT_X por every new number of ports we
have to handle.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496700722-13755-1-git-send-email-rodrigo.vivi@intel.com
The workaround added in
commit c6782b76d3 ("drm/i915/gen9: Reset secondary power well
equests left on by DMC/KVMR")
needs to be applied on Cannonlake as well.
So let's assume any platform using this power well setup
will also need and let's just go ahead and remove if condition.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-11-git-send-email-rodrigo.vivi@intel.com
CNL power wells are very similar to SKL, with the exception that the
misc IO well has been split into separate AUX IO wells.
Not sure if DMC is supposed to manage the AUX wells for us or not.
Let's assume so for now.
v2: DDI A power well wants DDI A domains, not DDI B domains
v3: s/BIT/BIT_ULL and add proper Aux IO domains. (Rodrigo)
v4: Remove PW_DDI_E. Not supported on Current CNL SKUs. (Rodrigo).
v5: Removed DDI_E_IO_DOMAINS and moved PORT_DDI_E_IO to DDI_A_IO
for the same reasons as v4 when we found out that current CNL
SKUs don't have the full port E split.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-10-git-send-email-rodrigo.vivi@intel.com
Indirect Context Offset Pointer has changed for Cannonlake.
INDIRECT_CTX_OFFSET[15:6] valid value for CNL is 19h per Spec.
v2: rebased to intel_lr_indirect_ctx_offset
v3: Commit message added per Tvrtko request.
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-9-git-send-email-rodrigo.vivi@intel.com
All registers and default configuration are the same for Skylake
and Cannonlake.
v2: Don't apply Wa for platforms without MOCS. (Paulo)
v3: Removed WaDisableSkipCaching that Joonas noticed that
according to spec it is not applicable to CNL.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-8-git-send-email-rodrigo.vivi@intel.com
Platform enabling and its power-on are organized in different
skus (U x Y x S x H, etc). So instead of organizing it in
GT1 x GT2 x GT3 let's also use the platform sku.
This is also the new Spec style what makes the review much
more easy and straightforward.
v2: Really include the PCI IDs to the picidlist[];
v3: Remove PCI IDs not present in spec.
v4: Rebase.
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Clinton Taylor <clinton.a.taylor@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-3-git-send-email-rodrigo.vivi@intel.com
Cannonlake is a Intel® Processor containing Intel® HD Graphics
following Kabylake.
It is Gen10.
Let's start by adding the platform definition based on previous
platforms but yet as alpha_support.
On following patches we will start adding PCI IDs and the
platform specific changes.
CNL has an increased DDB size as Damien had previously
noticed and provided a separated patch that got squashed here.
v2: Squash DDB size here per Ander request.
Credits-to: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496781040-20888-1-git-send-email-rodrigo.vivi@intel.com
The clipped src coordinates have already been rotated by 270 degrees for
when the plane rotation is 90/270 degrees, hence the FBC code should no
longer swap the width and height.
Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-4-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
skl_check_plane_surface() already rotates the clipped plane source
coordinates to match the scanout direction because that's the way
the GTT mapping is set up. Thus we no longer need to rotate the
coordinates in the watermark code.
For cursors we use the non-clipped coordinates which are not rotated
appropriately, but that doesn't actually matter since cursors don't
even support 90/270 degree rotation.
v2: Resolve conflicts from SKL+ wm rework
Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-3-ville.syrjala@linux.intel.com
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Starting from commit b63a16f6cd ("drm/i915: Compute display surface
offset in the plane check hook for SKL+") we've already rotated the src
coordinates by 270 degrees by the time we check if a scaler is needed
or not, so we must not account for the rotation a second time.
Previously we did these steps in the opposite order and hence the
scaler check had to deal with rotation itself. The double rotation
handling causes us to enable a scaler pretty much every time 90/270
degree plane rotation is requested, leading to fuzzier fonts and whatnot.
v2: s/unsigned/unsigned int/ to appease checkpatch
v3: s/DRM_ROTATE_0/DRM_MODE_ROTATE_0/
Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We're not that short on characters that we can't spell out
"false_color". Saves me from figuring out what "fc" means
the next time look at the code.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170606124412.5335-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The number of compressed segments has been available ever since
FBC2 was introduced in g4x, it just moved from the STATUS register
into STATUS2 on IVB.
For FBC1 if we really wanted the number of compressed segments we'd
have to trawl through the tags, but in this case since the code just
uses the number of compressed segments as an indicator whether
compression has occurred we can just check the state of the
COMPRESSING and COMPRESSED bits. IIRC the hardware will try to
periodically recompress all uncompressed lines even if they haven't
changed and the COMPRESSED bit will be cleared while the compressor
is running, so just checking the COMPRESSED bit might not give us
the right answer. Hence it seems better to check for both
COMPRESSED and COMPRESSING as that should tell us that the
compressor is at least trying to do something.
While at it move the IVB+ register define to the right place, unify
the naming convention of the compressed segment count masks, and
fix up the mask for g4x.
v2: s/ILK_DPFC_STATUS2/IVB_FBC_STATUS2/ (Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk> # SNB
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> # ilk+
Acked-by: Paulo Zanoni <paulo.r.zanoni@intel.com> # pre-ilk
Link: http://patchwork.freedesktop.org/patch/msgid/20170606124318.31755-1-ville.syrjala@linux.intel.com
The scanline counter is bonkers on VLV/CHV DSI. The scanline counter
increment is not lined up with the start of vblank like it is on
every other platform and output type. This causes problems for
both the vblank timestamping and atomic update vblank evasion.
On my FFRD8 machine at least, the scanline counter increment
happens about 1/3 of a scanline ahead of the start of vblank (which
is where all register latching happens still). That means we can't
trust the scanline counter to tell us whether we're in vblank or not
while we're on that particular line. In order to keep vblank
timestamping in working condition when called from the vblank irq,
we'll leave scanline_offset at one, which means that the entire
line containing the start of vblank is considered to be inside
the vblank.
For the vblank evasion we'll need to consider that entire line
to be bad, since we can't tell whether the registers already
got latched or not. And we can't actually use the start of vblank
interrupt to get us past that line as the interrupt would fire
too soon, and then we'd up waiting for the next start of vblank
instead. One way around that would using the frame start
interrupt instead since that wouldn't fire until the next
scanline, but that would require some bigger changes in the
interrupt code. So for simplicity we'll just poll until we get
past the bad line.
v2: Adjust the comments a bit
Cc: stable@vger.kernel.org
Cc: Jonas Aaberg <cja@gmx.net>
Tested-by: Jonas Aaberg <cja@gmx.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99086
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161215174734.28779-1-ville.syrjala@linux.intel.com
Tested-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Remove the SNB PCH refclock init call from the runtime resume handler.
I don't think it was actually needed even when we had SNB runtime PM,
and if definitely isn't needed ever since SNB runtime PM was nuked in
commit d4c5636e74 ("drm/i915: Remove runtime PM for SNB").
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601183043.28543-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Panel Power sequences for CNP is similar to Broxton,
but with only one sequencer.
Main difference from SPT is that PP_DIVISOR was removed
and power cycle delay has been moved to PP_CONTROL.
v2: Add missed pp_div write, that is now part of PP_CONTROL[8:4]
as on Broxton. (Found by DK)
v3: Improve commit message. (By DK)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Clinton Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-6-git-send-email-rodrigo.vivi@intel.com
On CNP PCH based platforms the gmbus is on the south display that
is on PCH. The existing implementation for previous platforms
already covers the need for CNP expect for the pin pair configuration
that follows similar definitions that we had on BXT.
v2: Don't drop "_BXT" as the indicator of the first platform
supporting this pin numbers. Suggested by Daniel.
v3: Add missing else and fix register table since CNP GPIO_CTL
starts on 0xC5014.
v4: Fix pin number and map according to the current available VBT.
Re-add pin 4 for port D. Lost during some rebase.
v5: Use table as spec. If VBT is wrong it should be ignored.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-5-git-send-email-rodrigo.vivi@intel.com
Split out BXT and CNP's setup_backlight(),enable_backlight(),
disable_backlight() and hz_to_pwm() into
two separate functions instead of reusing BXT function.
Reuse set_backlight() and get_backlight() since they have
no reference to the utility pin.
v2: Reuse BXT functions with controller 0 instead of
redefining it. (Jani).
Use dev_priv->rawclk_freq instead of getting the value
from SFUSE_STRAP.
v3: Avoid setup backligh controller along with hooks and
fully reuse hooks setup as suggested by Jani.
v4: Clean up commit message.
v5: Implement per PCH instead per platform.
v6: Introduce a new function for CNP.(Jani and Ville)
v7: Squash the all CNP Backlight support patches into a
single patch. (Jani)
v8: Correct indentation, remove unneeded blank lines and
correct mail address (Jani).
v9: Remove unused enum pipe. (by CI)
v10: Remove comment mentioning SFUSE_STRAP in a part of
the code that we don't use it. (Jani)
Make controller = 0 since current CNP has only one
controller and put a comment mentioning why we
reuse the BXT definitions and are keeping the
controller = 0. (DK)
v11: Remove spurious line. (DK)
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Ville Syrjala <ville.syrjala@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-4-git-send-email-rodrigo.vivi@intel.com
RAWCLK_FREQ register has changed for platforms with CNP+.
[29:26] This field provides the denominator for the fractional
part of the microsecond counter divider. The numerator
is fixed at 1. Program this field to the denominator of
the fractional portion of reference frequency minus one.
If the fraction is 0, program to 0.
0100b = Fraction .2 MHz = Fraction 1/5.
0000b = Fraction .0 MHz.
[25:16] This field provides the integer part of the microsecond
counter divider. Program this field to the integer portion
of the reference frequenct minus one.
Also this register tells us that proper raw clock should be read
from SFUSE_STRAP and programmed to this register. Up to this point
on other platforms we are reading instead of programming it so
probably relying on whatever BIOS had configured here.
Now on let's follow the spec and also program this register
fetching the right value from SFUSE_STRAP as Spec tells us to do.
v2: Read from SFUSE_STRAP and Program RAWCLK_FREQ instead of
reading the value relying someone else will program that
for us.
v3: Add missing else. (Jani)
v4: Addressing all Ville's catches:
Use macro for shift bits instead of defining shift.
Remove shift from the cleaning bits with mask that already
has it.
Add missing I915_WRITE to actually write the reg.
Stop using useless DIV_ROUND_* on divider that is exact
dividion and use DIV_ROUND_CLOSEST for the fraction part.
v5: Remove useless Read-Modify-Write on raclk_freq reg. (Ville).
v6: Change is per PCH instead of per platform.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-3-git-send-email-rodrigo.vivi@intel.com
The first two bytes of PCI ID for CNP_LP PCH are the same as that of
SPT_LP. We should really be looking at the first 9 bits instead of the
first 8 to identify platforms, although this seems to have not caused any
problems on earlier platforms. Introduce a 9 bit extended mask for SPT and
CNP while not touching the code for any of the other platforms.
v2: (Rodrigo) Make platform agnostic and fix commit message.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-2-git-send-email-rodrigo.vivi@intel.com
Most of south engine display that is in PCH is still the
same as SPT and KBP, except for this key differences:
- Backlight: Backlight programming changed in CNP PCH.
- Panel Power: Sligh programming changed in CNP PCH.
- GMBUS and GPIO: The pin mapping has changed in CNP PCH.
All of these changes follow more the BXT style.
v2: Update definition to use dev_priv isntead of dev (Tvrtko).
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496434004-29812-1-git-send-email-rodrigo.vivi@intel.com
In commit 5763ff04dc ("drm/i915: Avoid GPU stalls from kswapd") we
stopped direct reclaim and kswapd from triggering GPU/client stalls
whilst running (by restricting the objects they could reap to be idle).
However with abusive GPU usage, it becomes quite easy to starve kswapd
of memory and prevent it from making forward progress towards obtaining
enough free memory (thus driving the system closer to swap exhaustion).
Relax the previous restriction to allow kswapd (but not direct reclaim)
to stall the device whilst reaping purgeable pages.
v2: Also acquire the rpm wakelock to allow kswapd to unbind buffers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601133331.5973-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
I915_GEM_GET_APERTURE ioctl is used to probe aperture size from userspace.
In gvt environment, each vm only use the ballooned part of aperture, so we
should return the correct available aperture size exclude the reserved part
by balloon.
v2: add 'reserved' in struct i915_address_space to record the reserved size
in ggtt (Chris)
v3: remain aper_size as total, adjust aper_available_size exclude reserved
and pinned. UMD driver need to adjust the max allocation size according to
the available aperture size but not total size. KMD return the correct
usable aperture size any time (Chris, Joonas)
v4: decrease reserved in deballoon (Joonas)
v5: add onion teardown in balloon, add vgt_deballoon_space (Joonas)
v6: change title name (Zhenyu)
v7: code style refine (Joonas)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496198152-14175-1-git-send-email-weinan.z.li@intel.com
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The assertion that we want to make before disabling the pin of the pages
for the unknown swizzling quirk is that the quirk is indeed active, and
that the quirk is disabled before we do apply it to the pages.
Fixes: 2c3a3f44dc ("drm/i915: Fix pages pin counting around swizzle quirk")
Fixes: 957870f934 ("drm/i915: Split out i915_gem_object_set_tiling()")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170521124014.27678-1-chris@chris-wilson.co.uk
Reviewed-bhy: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
As another precaution when testing whether the CS engine is actually
idle, also inspect the ring's HEAD/TAIL registers, which should be equal
when there are no commands left to execute by the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170530121334.17364-3-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
When we enable the GuC, we enable an alternative mechanism for doing
post-GGTT update invalidation. Likewise, when we disable the GuC, we
restore the previous method. Assert that we change between known
endpoints, so that we can catch if we accidentally clobber some other
gen and if we change the invalidate routine without updating guc.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601090446.1334-1-chris@chris-wilson.co.uk
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Atm disabling either DP or eDP outputs can generate a spurious short
pulse interrupt. The reason is that after disabling the port the source
will stop sending a valid stream data, while the sink expects either a
valid stream or the idle pattern. Since neither of this is sent the sink
assumes (after an arbitrary delay) that the link is lost and requests
for link retraining with a short pulse.
The spurious pulse is a real problem at least for eDP panels with long
power-off / power-cycle delays: as part of disabling the output we
disable the panel power. The subsequent spurious short pulse handling
will have to turn the power back on, which means the driver has to do a
redundant wait for the power-off and power-cycle delays. During system
suspend this leads to an unnecessary delay up to ~1s on systems with
such panels as reported by Rui.
To fix this put the sink to DPMS D3 state before turning off the port.
According to the DP spec in this state the sink should not request
retraining. This is also what we do already on pre-ddi platforms.
As an alternative I also tried configuring the port to send idle pattern
- which is against BSPec - and leave the port in normal mode before
turning off the port. Neither of these resolved the problem.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-and-tested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496250335-7627-1-git-send-email-imre.deak@intel.com
Seems that GLK has a dotclock that's twice the display clock.
skl_max_scale checks for IS_GEMINILAKE, so perform the same check here.
While at it, change the DRM_ERROR to DEBUG_KMS.
Fixes: 73b0ca8ec7 ("drm/i915/skl+: consider max supported plane pixel
rate while scaling")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601103413.7037-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Commit 7c3f86b6dc ("drm/i915: Invalidate the guc ggtt TLB upon
insertion") added the restoration of the invalidation routine after the
GuC was disabled, but missed that the GuC was unconditionally disabled
when not used. This then overwrites the invalidate routine for the older
chipsets, causing havoc and breaking resume as the most obvious victim.
We place the guard inside i915_ggtt_disable_guc() to be backport
friendly (the bug was introduced into v4.11) but it would be preferred
to be in more control over when this was guard (i.e. do not try and
teardown the data structures before we have enabled them). That should
be true with the reorganisation of the guc loaders.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 7c3f86b6dc ("drm/i915: Invalidate the guc ggtt TLB upon insertion")
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: <stable@vger.kernel.org> # v4.11+
Link: http://patchwork.freedesktop.org/patch/msgid/20170531190514.3691-1-chris@chris-wilson.co.uk
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
A display resolution is only supported if it meets all the restrictions
below for Maximum Pipe Pixel Rate.
The display resolution must fit within the maximum pixel rate output
from the pipe. Make sure that the display pipe is able to feed pixels at
a rate required to support the desired resolution.
For each enabled plane on the pipe {
If plane scaling enabled {
Horizontal down scale amount = Maximum[1, plane horizontal size /
scaler horizontal window size]
Vertical down scale amount = Maximum[1, plane vertical size /
scaler vertical window size]
Plane down scale amount = Horizontal down scale amount *
Vertical down scale amount
Plane Ratio = 1 / Plane down scale amount
}
Else {
Plane Ratio = 1
}
If plane source pixel format is 64 bits per pixel {
Plane Ratio = Plane Ratio * 8/9
}
}
Pipe Ratio = Minimum Plane Ratio of all enabled planes on the pipe
If pipe scaling is enabled {
Horizontal down scale amount = Maximum[1, pipe horizontal source size /
scaler horizontal window size]
Vertical down scale amount = Maximum[1, pipe vertical source size /
scaler vertical window size]
Note: The progressive fetch - interlace display mode is equivalent to a
2.0 vertical down scale
Pipe down scale amount = Horizontal down scale amount *
Vertical down scale amount
Pipe Ratio = Pipe Ratio / Pipe down scale amount
}
Pipe maximum pixel rate = CDCLK frequency * Pipe Ratio
In this patch our calculation is based on pipe downscale amount
(plane max downscale amount * pipe downscale amount) instead of Pipe
Ratio. So,
max supported crtc clock with given scaling = CDCLK / pipe downscale.
Flip will fail if,
current crtc clock > max supported crct clock with given scaling.
Changes since V1:
- separate out fixed_16_16 wrapper API definition
Changes since V2:
- Fix buggy crtc !active condition (Maarten)
- use intel_wm_plane_visible wrapper as per Maarten's suggestion
Changes since V3:
- Change failure return from ERANGE to EINVAL
Changes since V4:
- Rebase based on previous patch changes
Changes since V5:
- return EINVAL instead of continue (Maarten)
Changes since V6:
- Improve commit message
- Address review comment
Changes since V7:
- use !enable instead of !active
- rename config variable for consistency (Maarten)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526151546.25025-4-mahesh1.kumar@intel.com
This patch implements new DDB allocation algorithm as per HW team
recommendation. This algo takecare of scenario where we allocate less DDB
for the planes with lower relative pixel rate, but they require more DDB
to work.
It also takes care of enabling same watermark level for each
plane in crtc, for efficient power saving.
Changes since v1:
- Rebase on top of Paulo's patch series
Changes since v2:
- Fix the for loop condition to enable WM
Changes since v3:
- Fix crash in cursor i-g-t reported by Maarten
- Rebase after addressing Paulo's comments
- Few other ULT fixes
Changes since v4:
- Rebase on drm-tip
- Added separate function to enable WM levels
Changes since v5:
- Fix a crash identified in skl-6770HQ system
Changes since v6:
- Address review comments from Matt
Changes since v7:
- Fix failure return in skl_compute_plane_wm (Matt)
- fix typo
Changes since v8:
- Always check cursor wm enable irrespective of total_data_rate
Changes since v9:
- fix typo
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601055918.4601-1-mahesh1.kumar@intel.com
On some systems there can be a race condition in which no crtc state is
added to the first atomic commit. This results in all crtc's having a
null DDB allocation, causing a FIFO underrun on any update until the
first modeset.
Changes since v1:
- Do not take the connection_mutex, this is already done below.
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Inspired-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 98d39494d3 ("drm/i915/gen9: Compute DDB allocation at atomic
check time (v4)")
Cc: <stable@vger.kernel.org> # v4.8+
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170531154236.27180-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Since
commit bac2a909a0
Author: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Date: Wed Jan 21 02:17:42 2015 +0100
PCI / PM: Avoid resuming PCI devices during system suspend
PCI devices will default to allowing the system suspend complete
optimization where devices are not woken up during system suspend if
they were already runtime suspended. This however breaks the i915/HDA
drivers for two reasons:
- The i915 driver has system suspend specific steps that it needs to
run, that bring the device to a different state than its runtime
suspended state.
- The HDA driver's suspend handler requires power that it will request
from the i915 driver's power domain handler. This in turn requires the
i915 driver to runtime resume itself, but this won't be possible if the
suspend complete optimization is in effect: in this case the i915
runtime PM is disabled and trying to get an RPM reference returns
-EACCESS.
Solve this by requiring the PCI/PM core to resume the device during
system suspend which in effect disables the suspend complete optimization.
Regardless of the above commit the optimization stayed disabled for DRM
devices until
commit d14d2a8453
Author: Lukas Wunner <lukas@wunner.de>
Date: Wed Jun 8 12:49:29 2016 +0200
drm: Remove dev_pm_ops from drm_class
so this patch is in practice a fix for this commit. Another reason for
the bug staying hidden for so long is that the optimization for a device
is disabled if it's disabled for any of its children devices. i915 may
have a backlight device as its child which doesn't support runtime PM
and so doesn't allow the optimization either. So if this backlight
device got registered the bug stayed hidden.
Credits to Marta, Tomi and David who enabled pstore logging,
that caught one instance of this issue across a suspend/
resume-to-ram and Ville who rememberd that the optimization was enabled
for some devices at one point.
The first WARN triggered by the problem:
[ 6250.746445] WARNING: CPU: 2 PID: 17384 at drivers/gpu/drm/i915/intel_runtime_pm.c:2846 intel_runtime_pm_get+0x6b/0xd0 [i915]
[ 6250.746448] pm_runtime_get_sync() failed: -13
[ 6250.746451] Modules linked in: snd_hda_intel i915 vgem snd_hda_codec_hdmi x86_pkg_temp_thermal intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul
snd_hda_codec_realtek snd_hda_codec_generic ghash_clmulni_intel e1000e snd_hda_codec snd_hwdep snd_hda_core ptp mei_me pps_core snd_pcm lpc_ich mei prime_
numbers i2c_hid i2c_designware_platform i2c_designware_core [last unloaded: i915]
[ 6250.746512] CPU: 2 PID: 17384 Comm: kworker/u8:0 Tainted: G U W 4.11.0-rc5-CI-CI_DRM_334+ #1
[ 6250.746515] Hardware name: /NUC5i5RYB, BIOS RYBDWi35.86A.0362.2017.0118.0940 01/18/2017
[ 6250.746521] Workqueue: events_unbound async_run_entry_fn
[ 6250.746525] Call Trace:
[ 6250.746530] dump_stack+0x67/0x92
[ 6250.746536] __warn+0xc6/0xe0
[ 6250.746542] ? pci_restore_standard_config+0x40/0x40
[ 6250.746546] warn_slowpath_fmt+0x46/0x50
[ 6250.746553] ? __pm_runtime_resume+0x56/0x80
[ 6250.746584] intel_runtime_pm_get+0x6b/0xd0 [i915]
[ 6250.746610] intel_display_power_get+0x1b/0x40 [i915]
[ 6250.746646] i915_audio_component_get_power+0x15/0x20 [i915]
[ 6250.746654] snd_hdac_display_power+0xc8/0x110 [snd_hda_core]
[ 6250.746661] azx_runtime_resume+0x218/0x280 [snd_hda_intel]
[ 6250.746667] pci_pm_runtime_resume+0x76/0xa0
[ 6250.746672] __rpm_callback+0xb4/0x1f0
[ 6250.746677] ? pci_restore_standard_config+0x40/0x40
[ 6250.746682] rpm_callback+0x1f/0x80
[ 6250.746686] ? pci_restore_standard_config+0x40/0x40
[ 6250.746690] rpm_resume+0x4ba/0x740
[ 6250.746698] __pm_runtime_resume+0x49/0x80
[ 6250.746703] pci_pm_suspend+0x57/0x140
[ 6250.746709] dpm_run_callback+0x6f/0x330
[ 6250.746713] ? pci_pm_freeze+0xe0/0xe0
[ 6250.746718] __device_suspend+0xf9/0x370
[ 6250.746724] ? dpm_watchdog_set+0x60/0x60
[ 6250.746730] async_suspend+0x1a/0x90
[ 6250.746735] async_run_entry_fn+0x34/0x160
[ 6250.746741] process_one_work+0x1f2/0x6d0
[ 6250.746749] worker_thread+0x49/0x4a0
[ 6250.746755] kthread+0x107/0x140
[ 6250.746759] ? process_one_work+0x6d0/0x6d0
[ 6250.746763] ? kthread_create_on_node+0x40/0x40
[ 6250.746768] ret_from_fork+0x2e/0x40
[ 6250.746778] ---[ end trace 102a62fd2160f5e6 ]---
v2:
- Use the new pci_dev->needs_resume flag, to avoid any overhead during
the ->pm_prepare hook. (Rafael)
v3:
- Update commit message to reference the actual regressing commit.
(Lukas)
v4:
- Rebase on v4 of patch 1/2.
Fixes: d14d2a8453 ("drm: Remove dev_pm_ops from drm_class")
References: https://bugs.freedesktop.org/show_bug.cgi?id=100378
References: https://bugs.freedesktop.org/show_bug.cgi?id=100770
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Marta Lofstedt <marta.lofstedt@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: linux-pci@vger.kernel.org
Cc: <stable@vger.kernel.org> # v4.10.x: 4d071c3 - PCI/PM: Add needs_resume flag
Cc: <stable@vger.kernel.org> # v4.10.x
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Marta Lofstedt <marta.lofstedt@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1493726649-32094-2-git-send-email-imre.deak@intel.com
We are passing parameters in the wrong order to find next zero bit, and
when it doesn't find anything it returns size (offset in the code), which
is always zero.
For reference the function is defined as:
find_next_bit( *addr, size, offset )
The incorrect parameter order was added by commit abddffdf36
("drm/i915/guc: Sanitize GuC client initialization"). Luckily, currently
we only use a single guc client and a single doorbell, which happens to be
zero; therefore it isn't necessary to backport this fix (which would be for
v4.12).
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170531000546.30762-1-michel.thierry@intel.com
psr1 is also disabled for panel resolution greater than 32X20.
Added psr2 check to disable only for psr2 panels having resolution
greater than 32X20.
issue was introduced by
commit-id : "acf45d11050abd751dcec986ab121cb2367dcbba"
commit message: "PSR2 is restricted to work with panel resolutions
upto 3200x2000, move the check to intel_psr_match_conditions and fully
block psr."
v2: (Rodrigo)
Add previous commit details which introduced the issue
Fixes: acf45d1105 ("drm/i915/psr: disable psr2 for resolution greater than 32X20")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Yaroslav Shabalin <yaroslav.shabalin@gmail.com>
Reported-by: Yaroslav Shabalin <yaroslav.shabalin@gmail.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: vathsala nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/49935bdff896ee3140bed471012b9f9110a863a4.1495729964.git.vathsala.nagaraju@intel.com
Currently GVT-g cannot work properly when host GuC submission is
enabled, so make the driver loading failed in this case.
v2:
- use DRM_ERROR as it is a fatal message. (Chris)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495878259-7733-2-git-send-email-chuanxiao.dong@intel.com
