On XDP_TX we need to free up the frame only when tun_xdp_tx() returns a
negative value. A positive value indicates that the packet is
successfully enqueued to the ptr_ring, so freeing the page causes
use-after-free.
Fixes: 735fc4054b ("xdp: change ndo_xdp_xmit API to support bulking")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hwrm_dbg_resp_addr and hwrm_dbg_resp_dma_addr are never used
and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the existing %pad printk format to print dma_addr_t values.
This avoids the following warnings when compiling on the parisc platform:
warning: format '%llx' expects argument of type 'long long unsigned int', but argument 2 has type 'dma_addr_t {aka unsigned int}' [-Wformat=]
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing entry for RTL8211C to mdio_device_id table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: cf87915cb9 ("net: phy: realtek: add support for RTL8211C")
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable *temp*.
This makes the code easier to read and maintain. Also, slightly
refactor some code due to the removal of *temp*.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network drivers include functionality to speed down the PHY when
suspending and just waiting for a WoL packet because this saves energy.
This functionality is quite generic, therefore let's factor it out to
phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This functionality will also be needed in subsequent patches of this
series, therefore factor it out to a helper.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually, hclge_get_ring_chain_from_mbx is used to get ring type, tqp id,
and int_gl index from mailbox message. So the comments is incorrect. This
patch fixes it.
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGE_INT_GL_IDX_M and HCLGE_INT_GL_IDX_S are used to set fireware
cmd. When getting int_gl value from mailbox message, we should use
HNAE3_RING_GL_IDX_M and HNAE3_RING_GL_IDX_S.
Fixes: 79eee41085 ("net: hns3: add int_gl_idx setup for VF")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
handle->reset_level is assigned to HNAE3_NONE_RESET when client is
initialized, if a tx timeout happens right after initialization,
then handle->reset_level is not resetted to HNAE3_FUNC_RESET in
hclge_reset_event, which will cause reset event not properly
handled problem.
This patch fixes it by setting handle->reset_level properly when
client is initialized.
Fixes: 6d4c3981a8 ("net: hns3: Changes to make enet watchdog timeout func common for PF/VF")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configuration of the ring will be used to reinitialize the
ring after the hardware reset is completed. So we should not
release and reacquire this configuration during reset.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reset, netdev has not been brought up is not an error,
it means that we do not need do the stop operation, so just return
zero.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware's description, driver should get reset event
from VECTOR0_PF_OTHER_INT_ST(0x20800) instead of
VECTOR0_PF_OTHER_INT_SRC(0x20700).
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdevice reset should not be requested frequently, a new one
must wait a moment since there may be some work not completed.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since current locking was not covering certain code where
netdev was being accessed or manipulated, this patch fixes
it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware's description, the head pointer register should
be written before the tail pointer register while doing command queue
initialization.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the byte count indication in CQE for processed IPsec
packets that contain a metadata header.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds common functions to handle mellanox metadata headers.
These functions are used by IPsec and TLS to process FPGA metadata.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables TLS Rx based on available HW capabilities.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds software statistics for TLS to count important
events.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the TLS rx offload data path according to the
requirements of the TLS generic NIC offload infrastructure.
Special metadata ethertype is used to pass information to
the hardware.
When hardware loses synchronization a special resync request
metadata message is used to request resync.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the mlx5 implementation of the TLS Rx routines to add/del TLS
contexts, also add the tls_dev_resync_rx routine
to work with the TLS inline Rx crypto offload infrastructure.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Innova TLS, TLS contexts are added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.
Complete the implementation for Innova TLS (FPGA-based) hardware by
adding support for rx inline crypto offload.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For symmetry, we rename mlx5e_tls_offload_context to
mlx5e_tls_offload_context_tx before we add mlx5e_tls_offload_context_rx.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Aviad Yehezkel <aviadye@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For symmetry, we rename tls_offload_context to
tls_offload_context_tx before we add tls_offload_context_rx.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The classification operations that are used for RSS make use of several
lookup tables. Having hit counters for these tables is really helpful
to determine what flows were matched by ingress traffic, and see the
path of packets among all the classifier tables.
This commit adds hit counters for the 3 tables used at the moment :
- The decoding table (also called lookup_id table), that links flows
identified by the Header Parser to the flow table.
There's one entry per flow, located at :
.../mvpp2/<controller>/flows/XX/dec_hits
Note that there are 21 flows in the decoding table, whereas there are
52 flows in the Header Parser. That's because there are several kind
of traffic that will match a given flow. Reading the hit counter from
one sub-flow will clear all hit counter that have the same flow_id.
This also applies to the flow_hits.
- The flow table, that contains all the different lookups to be
performed by the classifier for each packet of a given flow. The match
is done on the first entry of the flow sequence.
- The C2 engine entries, that are used to assign the default rx queue,
and enable or disable RSS for a given port.
There's one entry per flow, located at:
.../mvpp2/<controller>/flows/XX/flow_hits
There is one C2 entry per port, so the c2 hit counter is located at :
.../mvpp2/<controller>/ethX/c2_hits
All hit counter values are 16-bits clear-on-read values.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The classifier configuration for RSS is quite complex, with several
lookup tables being used. This commit adds useful info in debugfs to
see how the different tables are configured :
Added 2 new entries in the per-port directory :
- .../eth0/default_rxq : The default rx queue on that port
- .../eth0/rss_enable : Indicates if RSS is enabled in the C2 entry
Added the 'flows' directory :
It contains one entry per sub-flow. a 'sub-flow' is a unique path from
Header Parser to the flow table. Multiple sub-flows can point to the
same 'flow' (each flow has an id from 8 to 29, which is its index in the
Lookup Id table) :
- .../flows/00/...
/01/...
...
/51/id : The flow id. There are 21 unique flows. There's one
flow per combination of the following parameters :
- L4 protocol (TCP, UDP, none)
- L3 protocol (IPv4, IPv6)
- L3 parameters (Fragmented or not)
- L2 parameters (Vlan tag presence or not)
.../type : The flow type. This is an even higher level flow,
that we manipulate with ethtool. It can be :
"udp4" "tcp4" "udp6" "tcp6" "ipv4" "ipv6" "other".
.../eth0/...
.../eth1/engine : The hash generation engine used for this
flow on the given port
.../hash_opts : The hash generation options indicating on
what data we base the hash (vlan tag, src
IP, src port, etc.)
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One helpful feature to help debug the Header Parser TCAM filter in PPv2
is to be able to see if the entries did match something when a packet
comes in. This can be done by using the built-in hit counter for TCAM
entries.
This commit implements reading the counter, and exposing its value on
debugfs for each filter entry.
The counter is a 16-bits clear-on-read value, located at:
.../mvpp2/<controller>/parser/XXX/hits
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 Packer Header Parser has a TCAM based filter, that is not
trivial to configure and debug. Being able to dump TCAM entries from
userspace can be really helpful to help development of new features
and debug existing ones.
This commit adds a basic debugfs interface for the PPv2 driver, focusing
on TCAM related features.
<mnt>/mvpp2/ --- f2000000.ethernet
\- f4000000.ethernet --- parser --- 000 ...
| \- 001
| \- ...
| \- 255 --- ai
| \- header_data
| \- lookup_id
| \- sram
| \- valid
\- eth1 ...
\- eth2 --- mac_filter
\- parser_entries
\- vid_filter
There's one directory per PPv2 instance, named after pdev->name to make
sure names are uniques. In each of these directories, there's :
- one directory per interface on the controller, each containing :
- "mac_filter", which lists all filtered addresses for this port
(based on TCAM, not on the kernel's uc / mc lists)
- "parser_entries", which lists the indices of all valid TCAM
entries that have this port in their port map
- "vid_filter", which lists the vids allowed on this port, based on
TCAM
- one "parser" directory (the parser is common to all ports), containing :
- one directory per TCAM entry (256 of them, from 0 to 255), each
containing :
- "ai" : Contains the 1 byte Additional Info field from TCAM, and
- "header_data" : Contains the 8 bytes Header Data extracted from
the packet
- "lookup_id" : Contains the 4 bits LU_ID
- "sram" : contains the raw SRAM data, which is the result of the TCAM
lookup. This readonly at the moment.
- "valid" : Indicates if the entry is valid of not.
All entries are read-only, and everything is output in hex form.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the appropriate SPDX license identifiers and drop the license text.
This patch is only cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-07-15
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Various different arm32 JIT improvements in order to optimize code emission
and make the JIT code itself more robust, from Russell.
2) Support simultaneous driver and offloaded XDP in order to allow for advanced
use-cases where some work is offloaded to the NIC and some to the host. Also
add ability for bpftool to load programs and maps beyond just the cgroup case,
from Jakub.
3) Add BPF JIT support in nfp for multiplication as well as division. For the
latter in particular, it uses the reciprocal algorithm to emulate it, from Jiong.
4) Add BTF pretty print functionality to bpftool in plain and JSON output
format, from Okash.
5) Add build and installation to the BPF helper man page into bpftool, from Quentin.
6) Add a TCP BPF callback for listening sockets which is triggered right after
the socket transitions to TCP_LISTEN state, from Andrey.
7) Add a new cgroup tree command to bpftool which iterates over the whole cgroup
tree and prints all attached programs, from Roman.
8) Improve xdp_redirect_cpu sample to support parsing of double VLAN tagged
packets, from Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hosts using a VRRP router send their packets with a destination MAC of
the VRRP router which is of the following form [1]:
IPv4 - 00-00-5E-00-01-{VRID}
IPv6 - 00-00-5E-00-02-{VRID}
Where VRID is the ID of the virtual router. Such packets are directed to
the router block in the ASIC by an FDB entry that was added in the
previous patch.
However, in certain cases it is possible to skip this FDB lookup and
send such packets directly to the router. This is accomplished by adding
these special MAC addresses to the RIF cache. If the cache is hit, the
packet will skip the L2 lookup and ingress the router with the RIF
specified in the cache entry.
1. https://tools.ietf.org/html/rfc5798#section-7.3
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual Router Redundancy Protocol packets are used to communicate the
state of the Master router associated with the virtual router ID (VRID).
These are link-local multicast packets sent with IP protocol 112 that
are trapped in the router block in the ASIC.
Add a trap for these packets and mark the trapped packets to prevent
them from potentially being re-flooded by the bridge driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IP packet received on a netdev with a macvlan upper whose MAC matches
the packet's destination MAC will be re-injected to the Rx path as if it
was received by the macvlan, and perform an L3 lookup.
Reflect this functionality to the ASIC by programming FDB entries that
will direct MACs of macvlan uppers to the router.
In a similar fashion to router interfaces (RIFs) that are programmed
upon the addition of the first IP address on an interface and destroyed
upon the removal of the last IP address, the FDB entries for the macvlan
are added and destroyed based on the addition of the first and removal
of the last IP address on the macvlan.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow more unicast MAC addresses (e.g., VRRP virtual MAC) to
be directed to the router we need to enable macvlan uppers on top of
mlxsw netdevs.
Allow macvlan upper devices on top of mlxsw netdevs and sanitize
configurations that can't work. For example, a macvlan can't be enslaved
to a bridge as without ACLs the device doesn't take the destination MAC
into account when classifying a packet to a bridge instance (i.e., a
FID).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: f9358e12a0 ("net: mvpp2: split ingress traffic into multiple flows")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally left out the error handling for kstrtoul().
Fixes: a520030e32 ("qlcnic: Implement flash sysfs callback for 83xx adapter")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split handling of offloaded and driver programs completely. Since
offloaded programs always come with XDP_FLAGS_HW_MODE set in reality
there could be no sharing, anyway, programs would only be installed
in driver or in hardware. Splitting the handling allows us to install
programs in HW and in driver at the same time.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Allow netdevsim to accept driver and offload attachment of XDP
BPF programs at the same time.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Split the query of HW-attached program from the software one.
Introduce new .ndo_bpf command to query HW-attached program.
This will allow drivers to install different programs in HW
and SW at the same time. Netlink can now also carry multiple
programs on dump (in which case mode will be set to
XDP_ATTACHED_MULTI and user has to check per-attachment point
attributes, IFLA_XDP_PROG_ID will not be present). We reuse
IFLA_XDP_PROG_ID skb space for second mode, so rtnl_xdp_size()
doesn't need to be updated.
Note that the installation side is still not there, since all
drivers currently reject installing more than one program at
the time.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Basic operations drivers perform during xdp setup and query can
be moved to helpers in the core. Encapsulate program and flags
into a structure and add helpers. Note that the structure is
intended as the "main" program information source in the driver.
Most drivers will additionally place the program pointer in their
fast path or ring structures.
The helpers don't have a huge impact now, but they will
decrease the code duplication when programs can be installed
in HW and driver at the same time. Encapsulating the basic
operations in helpers will hopefully also reduce the number
of changes to drivers which adopt them.
Helpers could really be static inline, but they depend on
definition of struct netdev_bpf which means they'd have
to be placed in netdevice.h, an already 4500 line header.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
prog_attached of struct netdev_bpf should have been superseded
by simply setting prog_id long time ago, but we kept it around
to allow offloading drivers to communicate attachment mode (drv
vs hw). Subsequently drivers were also allowed to report back
attachment flags (prog_flags), and since nowadays only programs
attached will XDP_FLAGS_HW_MODE can get offloaded, we can tell
the attachment mode from the flags driver reports. Remove
prog_attached member.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The hardware supposedly handles frames up to 10236 bytes and
implements .ndo_change_mtu() so accept 10236 minus the ethernet
header for a VLAN tagged frame on the netdevices. Use
ETH_MIN_MTU as minimum MTU.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initialization sequence for the ethernet, setting up
interrupt routing and such things, need to be done after
both the ports are clocked and reset. Before this the
config will not "take". Move the initialization to the
port probe function and keep track of init status in
the state.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code was not tested with two ports actually in use at
the same time. (I blame this on lack of actual hardware using
that feature.) Now after locating a system using both ports,
add necessary fix to make both ports come up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch over to using a module parameter and debug prints
that can be controlled by this or ethtool like everyone
else. Depromote all other prints to debug messages.
The phy_print_status() was already in place, albeit never
really used because the debuglevel hiding it had to be
set up using ethtool.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to calculate the hardware register enumerator
for the maximum L3 length isn't entirely simple to read.
Use the existing defines and rewrite the function into a
table look-up.
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This parameter enables capturing region snapshot of the crspace
during critical errors. The default value of this parameter is
disabled, it can be enabled using devlink param commands.
It is possible to configure during runtime and also driver init.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Crdump allows the driver to create a snapshot of the FW PCI
crspace and health buffer during a critical FW issue.
In case of a FW command timeout, FW getting stuck or a non zero
value on the catastrophic buffer, a snapshot will be taken.
The snapshot is exposed using devlink, cr-space, fw-health
address regions are registered on init and snapshots are attached
once a new snapshot is collected by the driver.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Health buffer address is a 32 bit PCI address offset provided by
the FW. This offset is used for reading FW health debug data
located on the shared CR space. Cr space is accessible in both
driver and FW and allows for different queries and configurations.
Health buffer size is always 64B of readable data followed by a
lock which is used to block volatile CR space access.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows setting the RSS hash generation parameters from
ethtool. When setting parameters for a given flow type from ethtool
(e.g. tcp4), all the corresponding flows in the flow table are updated,
according to the supported hash parameters.
For example, when configuring TCP over IPv4 hash parameters to be
src/dst IP + src/dst port ("ethtool -N eth0 rx-flow-hash tcp4 sdfn"),
we only set the "src/dst port" hash parameters on the non-fragmented TCP
over IPv4 flows.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the classification action that can be performed is to compute a
hash of the packet header based on some header fields, and lookup a RSS
table based on this hash to determine the final RxQ.
This is done by adding one lookup entry per flow per port, so that we
can configure the hash generation parameters for each flow and each
port.
There are 2 possible engines that can be used for RSS hash generation :
- C3HA, that generates a hash based on up to 4 header-extracted fields
- C3HB, that does the same as c3HA, but also includes L4 info in the hash
There are a lot of fields that can be extracted from the header. For now,
we only use the ones that we can configure using ethtool :
- DST MAC address
- L3 info
- Source IP
- Destination IP
- Source port
- Destination port
The C3HB engine is selected when we use L4 fields (src/dst port).
Header parser Dec table
Ingress pkt +-------------+ flow id +----------------------------+
------------->| TCAM + SRAM |-------->|TCP IPv4 w/ VLAN, not frag |
+-------------+ |TCP IPv4 w/o VLAN, not frag |
|TCP IPv4 w/ VLAN, frag |--+
|etc. | |
+----------------------------+ |
|
Flow table |
+---------+ +------------+ +--------------------------+ |
| RSS tbl |<--| Classifier |<--------| flow 0: C2 lookup | |
+---------+ +------------+ | C3 lookup port 0 | |
| | | C3 lookup port 1 | |
+-----------+ +-------------+ | ... | |
| C2 engine | | C3H engines | | flow 1: C2 lookup |<--+
+-----------+ +-------------+ | C3 lookup port 0 |
| ... |
| ... |
| flow 51 : C2 lookup |
| ... |
+--------------------------+
The C2 engine also gains the role of enabling and disabling the RSS
table lookup for this packet.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 classifier allows to perform classification operations on each
ingress packet, based on the flow the packet is assigned to.
The current code uses only 1 flow per port, and the only classification
action consists of assigning the rx queue to the packet, depending on the
port.
In preparation for adding RSS support, we have to split all incoming
traffic into different flows. Since RSS assigns a rx queue depending on
the hash of some header fields, we have to make sure that the hash is
generated in a consistent way for all packets in the same flow.
What we call a "flow" is actually a set of attributes attached to a
packet that depends on various L2/L3/L4 info.
This patch introduces 52 flows, wich are a combination of various L2, L3
and L4 attributes :
- Whether or not the packet has a VLAN tag
- Whether the packet is IPv4, IPv6 or something else
- Whether the packet is TCP, UDP or something else
- Whether or not the packet is fragmented at L3 level.
The flow is associated to a packet by the Header Parser. Each flow
corresponds to an entry in the decoding table. This entry then points to
the sequence of classification lookups to be performed by the
classifier, represented in the flow table.
For now, the only lookup we perform is a C2 lookup to set the default
rx queue.
Header parser Dec table
Ingress pkt +-------------+ flow id +----------------------------+
------------->| TCAM + SRAM |-------->|TCP IPv4 w/ VLAN, not frag |
+-------------+ |TCP IPv4 w/o VLAN, not frag |
|TCP IPv4 w/ VLAN, frag |--+
|etc. | |
+----------------------------+ |
|
Flow table |
+------------+ +---------------------+ |
To RxQ <---| Classifier |<-------| flow 0: C2 lookup |<--------+
+------------+ | flow 1: C2 lookup |
| | ... |
+------------+ | flow 51 : C2 lookup |
| C2 engine | +---------------------+
+------------+
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 Controller has a classifier, that can perform multiple lookup
operations for each packet, using different engines.
One of these engines is the C2 engine, which performs TCAM based lookups
on data extracted from the packet header. When a packet matches an
entry, the engine sets various attributes, used to perform
classification operations.
One of these attributes is the rx queue in which the packet should be sent.
The current code uses the lookup_id table (also called decoding table)
to assign the rx queue. However, this only works if we use one entry per
port in the decoding table, which won't be the case once we add RSS
lookups.
This patch uses the C2 engine to assign the rx queue to each packet.
The C2 engine is used through the flow table, which dictates what
classification operations are done for a given flow.
Right now, we have one flow per port, which contains every ingress
packet for this port.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvpp22_init_rss function configures the RSS parameters for each port, so
rename it accordingly. Since this function relies on classifier
configuration, move its call right after the classifier config.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When filling the RSS table, we have to make sure that the rx queue is
attached to an online CPU.
This patch is not a full support for cpu_hotplug, but rather a way to
make sure that we don't break network on system booted with the maxcpus
parameter.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an extra indirection when setting the indirection table
into the RSS hardware table to improve the packets distribution across
CPUs. For example, if 2 queues are used on a multi-core system this new
indirection will choose two queues on two different CPUs instead of the
two first queues which are on the same first CPU.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the RSS indirection table support, allowing to use the
ethtool -x and -X options to dump and set this table.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
[Maxime: Small warning fixes, use one table per port]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2 Controller has 8 RSS Tables, of 32 entries each. A lookup in the
RXQ2RSS_TABLE is performed for each incoming packet, and the RSS Table
to be used is chosen according to the default rx queue that would be
used for the packet.
This default rx queue is set in the Lookup_id Table (also called
Decoding Table), and is equal to the port->first_rxq.
Since the Classifier itself isn't active at any time for the moment,
this doesn't have a direct effect, the default rx queue at the moment is
the one where all packets end-up into.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no RSS_TABLE register in PPv2 Controller. The register 0x1510
which was specified is actually named "RSS_HASH_SEL", but isn't used by
this driver at all.
Based on how this register was used, it should have been the
RXQ2RSS_TABLE register, which allows to select the RSS table that will
be used for the incoming packet.
The RSS_TABLE_POINTER is actually a field of this RXQ2RSS_TABLE
register.
Since RSS tables are actually not used by the driver for now, this
commit does not fix a runtime bug.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch fixing a typo in one of the RSS comments.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of receive queue per port is :
- MVPP2_DEFAULT_RXQ if in single queue mode
- MVPP2_DEFAULT_RXQ * num_possible_cpus if in multi queue mode
with MVPP2_DEFAULT_RXQ = 4.
However, we don't use the extra rx queues at the moment, we really only
need one per port per CPU, until some more advanced classification rules
are implemented.
Suggested-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a dedicated #define that indicates the number of rx queues per
port per cpu, this commit removes a harcoded use of that value
This doesn't fix any runtime bugs since the harcoded value matches the
expected value.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since RSS only applies when we have per-cpu rx queues, it should only
be enabled when the driver is configured to make use of multi-queue
mode.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Maxime: Commit message]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multi queue mode is needed to have RSS available, and offers some
nice advantages, being able to have one rx queue vector per CPU.
This mode has been usable through the use of a module parameter, this
commit makes it the default value.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 driver defines 2 "queue_modes" :
- QDIST_SINGLE_MODE, where each port share one rx queue vector
between all CPUs
- QDIST_MULTI_MODE, where each port has one rx queue vector per CPU.
Multi queue mode isn't available on PPv2.1, make sure we fallback to
single mode when running on this revision.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the the RSS indirection tables should be defined in mvpp2.h,
so that we can use it in all files of the PPv2 driver.
This commit moves the define in mvpp2.h, and adds the missing #include
in mvpp2_cls.h.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include guards should be put before #includes. This doesn't fix any bug,
but prevent future compilation issues when adding new files in the mvpp2
driver
The Header Parser init function needs the platform_device definition,
and with the fixed include guards we need to add the missing include.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
getnstimeofday64 is deprecated in favor of the ktime_get() family of
functions. The direct replacement would be ktime_get_real_ts64(),
but I'm picking the basic ktime_get() instead:
- using a ktime_t simplifies the code compared to timespec64
- using monotonic time instead of real time avoids issues caused
by a concurrent settimeofday() or during a leap second adjustment.
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two do the same thing, but we want to have a consistent
naming in the kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should take and release the filter_sem consistently during the
reset process, in the same manner as the mac_lock and reset_lock.
For lockdep consistency we also take the filter_sem for write around
other calls to efx->type->init().
Fixes: c2bebe37c6 ("sfc: give ef10 its own rwsem in the filter table instead of filter_lock")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some situations we may end up calling down_read while already
holding the semaphore for write, thus hanging. This has been seen
when setting the MAC address for the interface. The hung task log
in this situation includes this stack:
down_read
efx_ef10_filter_insert
efx_ef10_filter_insert_addr_list
efx_ef10_filter_vlan_sync_rx_mode
efx_ef10_filter_add_vlan
efx_ef10_filter_table_probe
efx_ef10_set_mac_address
efx_set_mac_address
dev_set_mac_address
In addition, lockdep rightly points out that nested calling of
down_read is incorrect.
Fixes: c2bebe37c6 ("sfc: give ef10 its own rwsem in the filter table instead of filter_lock")
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT Lite reversed the logic compared to SYSTEMPORT, the
GIB_FCS_STRIP bit is set when the Ethernet FCS is stripped, and that bit
is not set by default. Fix the logic such that we properly check whether
that bit is set or not and we don't forward an extra 4 bytes to the
network stack.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-07-12
This series contains updates to ixgbe and e100/e1000 kernel documentation.
Alex fixes ixgbe to ensure that we are more explicit about the ordering
of updates to the receive address register (RAR) table.
Dan Carpenter fixes an issue where we were reading one element beyond
the end of the array.
Mauro Carvalho Chehab fixes formatting issues in the e100.rst and
e1000.rst that were causing errors during 'make htmldocs'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipsec->tx_tbl[] has IXGBE_IPSEC_MAX_SA_COUNT elements so the > needs
to be changed to >= so we don't read one element beyond the end of the
array.
Fixes: 5925947047 ("ixgbe: process the Tx ipsec offload")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we are much more explicit about the ordering
of updates to the receive address register (RAR) table. Prior to this patch
I believe we may have been updating the table while entries were still
active, or possibly allowing for reordering of things since we weren't
explicitly flushing writes to either the lower or upper portion of the
register prior to accessing the other half.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2018-07-11
An update from ieee802154 for your *net* tree.
Build system fix for a missing include from Arnd Bergmann.
Setting the IFLA_LINK for the lowpan parent from Lubomir Rintel.
Fixes for some RX corner cases in adf7242 driver by Michael Hennerich.
And some small patches to cleanup our BUG_ON vs WARN_ON usage.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Unionize two u8 fields where only one of them is used depending on NIC
chipset.
- Move recovery_supported field after that union
These changes eliminate 7-bytes hole in the struct and makes it smaller
by 8 bytes.
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-order fields in struct be_eq_obj to ensure that .napi field begins
at start of cache-line. Also the .adapter field is moved to the first
cache-line next to .q field and 3 fields (idx,msi_idx,spurious_intr)
and the 4-bytes hole to 3rd cache-line.
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The event queue description (be_eq_obj.desc) field is used only to format
string for IRQ name and it is not really needed to hold this value.
Remove it and use local variable to format string for IRQ name.
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit fb6113e688 ("be2net: get rid of custom busy poll code")
replaced custom busy-poll code by the generic one but left several
macros and fields in struct be_eq_obj that are currently unused.
Remove this stuff.
Fixes: fb6113e688 ("be2net: get rid of custom busy poll code")
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 2632bafd74 ("be2net: fix adaptive interrupt coalescing")
introduced a separate struct be_aic_obj to hold AIC information but
unfortunately left the old stuff in be_eq_obj. So remove it.
Fixes: 2632bafd74 ("be2net: fix adaptive interrupt coalescing")
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in qed_probe message.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The late ts queue can contain a bunch of skbs while hi rate testing,
no need to check all of them if timestamp is already matched.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was been observed that with a particular order of initialisation,
the netdev can be up, but the SFP module still has its TX_DISABLE
signal asserted. This occurs when the network device brought up before
the SFP kernel module has been inserted by userspace.
This occurs because sfp-bus layer does not hear about the change in
network device state, and so assumes that it is still down. Set
netdev->sfp when the upstream is registered to work around this problem.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We fail to correctly clean up after a bus registration failure, which
can lead to an incorrect assumption about the registration state of
the upstream or sfp cage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading mirror-to-gretap, mlxsw needs to preroute the path that
the encapsulated packet will take. That path may include a LAG device
above a front panel port. So far, mlxsw resolved the path to the first
up front panel slave of the LAG interface, but that only reflects
administrative state of the port. It neglects to consider whether the
port actually has a carrier, and what the LACP state is.
So instead of checking upness of the device, check carrier state and
txability.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch adds a new entry point, team_port_dev_txable(). Making
it an ordinary exported function would mean that any module that may
need the service in one of the supported configurations also
unconditionally needs to pull in the team module, whether or not the
user actually intends to create team interfaces.
To prevent that, team_port_dev_txable() is defined in if_team.h, and
therefore all dependencies of that function also need to be
publicly-visible.
Therefore move team_port_get_rcu() from team.c to if_team.h.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today macvlan ignores the notification when a lower device goes
administratively down, preventing the lack of connectivity from
bubbling up.
Processing NETDEV_DOWN results in a macvlan state of LOWERLAYERDOWN
with NO-CARRIER which should be easy to interpret in userspace.
2: lower: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
3: macvlan@lower: <NO-CARRIER,BROADCAST,MULTICAST,UP,M-DOWN> mtu 1500 qdisc noqueue state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
Signed-off-by: Suresh Krishnan <skrishnan@arista.com>
Signed-off-by: Travis Brown <travisb@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
L2 Fwd Offload & 10GbE Intel Driver Updates 2018-07-09
This patch series is meant to allow support for the L2 forward offload, aka
MACVLAN offload without the need for using ndo_select_queue.
The existing solution currently requires that we use ndo_select_queue in
the transmit path if we want to associate specific Tx queues with a given
MACVLAN interface. In order to get away from this we need to repurpose the
tc_to_txq array and XPS pointer for the MACVLAN interface and use those as
a means of accessing the queues on the lower device. As a result we cannot
offload a device that is configured as multiqueue, however it doesn't
really make sense to configure a macvlan interfaced as being multiqueue
anyway since it doesn't really have a qdisc of its own in the first place.
The big changes in this set are:
Allow lower device to update tc_to_txq and XPS map of offloaded MACVLAN
Disable XPS for single queue devices
Replace accel_priv with sb_dev in ndo_select_queue
Add sb_dev parameter to fallback function for ndo_select_queue
Consolidated ndo_select_queue functions that appeared to be duplicates
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose stats obtained from firmware via debugfs. These stats can't
be part of ethtool -S because the slow firmware mailbox can cause
packet drops under heavy load.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running ethtool -S, some stats are requested from firmware.
Since getting these stats via firmware mailbox is slow, some packets
get dropped under heavy load while running ethtool -S.
So, remove these stats from ethtool -S.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PPv2 driver uses interrupts and tasklet but does not
explicitly include linux/interrupt.h, relying on implicit includes. This
one particularly is included by chance after a long unlogical chain of
inclusions. Fix this so we do not get future build breaks.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Size of csk_tbl is about 58K, which means 3rd order page allocation.
kvzalloc provides a fallback if no high order memory is available.
Signed-off-by: Jan Dakinevich <jan.dakinevich@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables ack_status, bcf and protocol are being assigned but are
never used hence they are redundant and can be removed.
Also declare ack_type as unsigned int rather than unsigned to clean
up a checkpatch warning.
Cleans up clang warnings:
warning: variable 'ack_status' set but not used [-Wunused-but-set-variable]
warning: variable 'bcf' set but not used [-Wunused-but-set-variable]
warning: variable 'protocol' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
congestion argument passed to t4_sge_alloc_rxq() is used
to differentiate between nic/ofld queues.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
In this case, the affected files are in debugfs (and should therefore only
be accessible to root) and check that *pos is zero (which prevents the
sys_splice() trick). Therefore, this is not a security fix, but rather a
small cleanup.
For the read handlers, fix it by using simple_read_from_buffer() instead of
custom logic.
For the write handler, add a check.
changed in v2:
- also fix dbg_write()
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix bug in the error code path when bnxt_request_irq() returns failure.
bnxt_disable_napi() should not be called in this error path because
NAPI has not been enabled yet.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling bnxt_set_max_func_irqs() to modify the max IRQ count requested or
freed by the RDMA driver is flawed. The max IRQ count is checked when
re-initializing the IRQ vectors and this can happen multiple times
during ifup or ethtool -L. If the max IRQ is reduced and the RDMA
driver is operational, we may not initailize IRQs correctly. This
problem shows up on VFs with very small number of MSIX.
There is no other logic that relies on the IRQ count excluding the ones
used by RDMA. So we fix it by just removing the call to subtract or
add the IRQs used by RDMA.
Fixes: a588e4580a ("bnxt_en: Add interface to support RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver assumes IFF_BROADCAST is always set and always sets
the broadcast filter. Modify the code to set or clear the broadcast
filter according to the IFF_BROADCAST flag.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code returns -ENOMEM and does not bother to set the output
parameters to 0 when no rings are available. Some callers, such as
bnxt_get_channels() will display garbage ring numbers when that happens.
Fix it by always setting the output parameters.
Fixes: 6e6c5a57fb ("bnxt_en: Modify bnxt_get_max_rings() to support shared or non shared rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there aren't enough RX rings available, the driver will attempt to
use a single RX ring without the aggregation ring. If that also
fails, the BNXT_FLAG_AGG_RINGS flag is cleared but the other ring
parameters are not set consistently to reflect that. If more RX
rings become available at the next open, the RX rings will be in
an inconsistent state and may crash when freeing the RX rings.
Fix it by restoring the BNXT_FLAG_AGG_RINGS if not enough RX rings are
available to run without aggregation rings.
Fixes: bdbd1eb59c ("bnxt_en: Handle no aggregation ring gracefully.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that OVS may set don’t care for DEI/CFI bit in
vlan_tci mask. Hence, checking for vlan_tci exact match will endup
in a vlan flow rejection.
This patch fixes the problem by checking for vlan_pcp and vid
separately, instead of checking for the entire vlan_tci.
Fixes: e85a9be93c (bnxt_en: do not allow wildcard matches for L2 flows)
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These resources are needed for Spectrum-2 KVD linear management
implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for Spectrum-2 FW version checking and
make mlxsw_sp_fw_rev_validate() per-ASIC as well as required FW revision
and FW filename.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Spectrum-2, we need to insert priority to C-TCAM because HW
needs that info in order to correctly process scenarios where rules
are in both C-TCAM and A-TCAM.
So extend the mlxsw_sp_acl_ctcam_entry_add() args to accept indication
if priority needs to be filled up and implement the priority
computation and fill-up.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is going to be needed for Spectrum-2 C-TCAM implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Spectrum-2 encodes blocks into different HW layout, push this
code into Spectrum-specific op.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the flex keys for Spectrum-2 differ not only in blocks definitions
but also in encoding layout, prepare for the implementation and pass
Spectrum/Spectrum-2 specific ops down to mlxsw_afk_create.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ops to be called on driver instance init and fini.
This is needed in order to be possible to do Spectrum-2 specific init
and fini work.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow easy and clean Spectrum-2 implementation for things that differ
from Spectrum, split the existing ACL TCAM code 3 ways:
1) common code that calls Spectrum/Spectrum-2 specific ops
2) Spectrum ops implementations
3) common C-TCAM code that is going to be shared between Spectrum and
Spectrum-2 implementations
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Spectrum-2 has different handling of TCAM, push Spectrum MR TCAM
bits to a separate file accessible by ops which allows to implement
Spectrum-2 specific ops.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the Spectrum-2 KVD linear manager implementation, entry_count will be
needed even for the free function. So pass it down.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future Spectrum-2 KVD linear manager implementation needs to know type
of the entry to alloc and free. So define the types in an enum and
pass it down to alloc and free functions. Once the entry type
is passed down, KVDL common part knows sizes of each entry types,
so replace size function arg with entry count.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2 there is a different implementation of KVD linear
management. Unlike in Spectrum where there is a single index space,
in Spectrum-2 the indexes are per-resource. Also there is need to
explicitly tell HW that an entry is no longer used.
So push out the existing implementation into spectrum1_kvdl.c and
prepare ops infrastructure to allow new implementation in a follow-up.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This restores the use of 2-factor allocation helpers that were already
fixed treewide. Please do not use open-coded multiplication; prefer,
instead, using 2-factor allocation helpers.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most of these calls we can just pass NULL through to the fallback
function as the sb_dev. The only cases where we cannot are the cases where
we might be dealing with either an upper device or a driver that would
have configured things to support an sb_dev itself.
The only driver that has any significant change in this patch set should be
ixgbe as we can drop the redundant functionality that existed in both the
ndo_select_queue function and the fallback function that was passed through
to us.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that instead of passing a void pointer as the
accel_priv we instead pass a net_device pointer as sb_dev. Making this
change allows us to pass the subordinate device through to the fallback
function eventually so that we can keep the actual code in the
ndo_select_queue call as focused on possible on the exception cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a generic version of the ndo_select_queue functions for
either returning 0 or selecting a queue based on the processor ID. This is
generally meant to just reduce the number of functions we have to change
in the future when we have to deal with ndo_select_queue changes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can support the concept of subordinate
device traffic classes to the core networking code. In doing this we can
start pulling out the driver specific bits needed to support selecting a
queue based on an upper device.
The solution at is currently stands is only partially implemented. I have
the start of some XPS bits in here, but I would still need to allow for
configuration of the XPS maps on the queues reserved for the subordinate
devices. For now I am using the reference to the sb_dev XPS map as just a
way to skip the lookup of the lower device XPS map for now as that would
result in the wrong queue being picked.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that we use the tc_to_txq mapping in the macvlan
device in order to select the Tx queue for outgoing packets.
The idea here is to try and move away from using ixgbe_select_queue and to
come up with a generic way to make this work for devices going forward. By
encoding this information in the netdev this can become something that can
be used generically as a solution for similar setups going forward.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reissuing RC_RX every 400ms - to adjust for offset drift in
receiver see datasheet page 61, OCL section.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Only enable RX mode if the netdev is opened.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Add support for HE in mac8011_hwsim, conforming with P802.11ax_D2.0.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The check is valid but it does not warrant to crash the kernel. A
WARN_ON() is good enough here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Instead of having the function name hard-coded (it might change and we
forgot to update them in the debug output) we can use __func__ instead
and also shorter the line so we do not need to break it. Also fix an
extra blank line while being here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
The check is valid but it does not warrant to crash the kernel. A
WARN_ON() is good enough here.
Found by checkpatch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
-----BEGIN PGP SIGNATURE-----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=IOF/
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix a use-after-free in the endpoint code (Dan Carpenter)
- Stop defaulting CONFIG_PCIE_DW_PLAT_HOST to yes (Geert Uytterhoeven)
- Fix an nfp regression caused by a change in how we limit the number
of VFs we can enable (Jakub Kicinski)
- Fix failure path cleanup issues in the new R-Car gen3 PHY support
(Marek Vasut)
- Fix leaks of OF nodes in faraday, xilinx-nwl, xilinx (Nicholas Mc
Guire)
* tag 'pci-v4.18-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
nfp: stop limiting VFs to 0
PCI/IOV: Reset total_VFs limit after detaching PF driver
PCI: faraday: Add missing of_node_put()
PCI: xilinx-nwl: Add missing of_node_put()
PCI: xilinx: Add missing of_node_put()
PCI: endpoint: Use after free in pci_epf_unregister_driver()
PCI: controller: dwc: Do not let PCIE_DW_PLAT_HOST default to yes
PCI: rcar: Clean up PHY init on failure
PCI: rcar: Shut the PHY down in failpath
The helper should return always KVD linear index of the second set.
It is unused now, but going to be used soon.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, the real action sets are always in KVD linear. The first
set is always empty and contains only pointer to the first real set in
KVD linear. So provide possibility to specify the first set is the dummy
one.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 need a slightly different handling of flexible actions. So
put an ops pointer in mlxsw_sp struct and rename it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SRC_SYS_PORT is passed as 8 bit value down to hw anyway, so cap it
in the driver as well. Also, in Spectrum-2 the FW iface for SRC_SYS_PORT
is only 8 bits, so prepare for it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since in Spectrum-2, MACs are split and IP addresses are split as well,
in order to use the same elements for Spectrum and Spectrum-2 split them
now.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lowest 16 bits of tp->prio are always zero, so ignore them with a
shift.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce Flex2 key type for PTAR register which is used in Spectrum-2.
Also, extend mlxsw_reg_ptar_pack() to set the value according to the
caller.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is specific for Spectrum as Spectrum-2 has completely different key
blocks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable next_rx is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'next_rx' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested on AM572x with cpsw v1.15 for PTP sync and delay_req messages.
It doesn't work on cpsw v1.12, so added only for cpsw v > 1.15.
Command for testing:
ptp4l -P -4 -H -i eth0 -l 6 -m -q -p /dev/ptp0 -f ptp.cfg
where ptp.cfg:
[global]
tx_timestamp_timeout 20
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's needed to avoid checkpatch warnings for farther changes.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I link error on 32-bit ARM points to yet another arithmetic bug:
drivers/net/ethernet/stmicro/stmmac/stmmac_tc.o: In function `tc_setup_cbs':
stmmac_tc.c:(.text+0x148): undefined reference to `__aeabi_uldivmod'
stmmac_tc.c:(.text+0x1fc): undefined reference to `__aeabi_uldivmod'
stmmac_tc.c:(.text+0x308): undefined reference to `__aeabi_uldivmod'
stmmac_tc.c:(.text+0x320): undefined reference to `__aeabi_uldivmod'
stmmac_tc.c:(.text+0x33c): undefined reference to `__aeabi_uldivmod'
drivers/net/ethernet/stmicro/stmmac/stmmac_tc.o:stmmac_tc.c:(.text+0x3a4): more undefined references to `__aeabi_uldivmod' follow
I observe that the last change to add the 'ul' prefix was incorrect,
as it did not turn the result of the multiplication into a 64-bit
expression on 32-bit architectures. Further, it seems that the
do_div() macro gets confused by the fact that we pass a signed
variable rather than unsigned into it.
This changes the code to instead use the div_s64() helper that is
meant for signed division, along with changing the constant suffix
to 'll' to actually make it a 64-bit argument everywhere, fixing
both of the issues I pointed out.
I'm not completely convinced that this makes the code correct, but
I'm fairly sure that we have two problems less than before.
Fixes: 1f705bc61a ("net: stmmac: Add support for CBS QDISC")
Fixes: c18a9c0966 ("net: stmmac_tc: use 64-bit arithmetic instead of 32-bit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GEM version in ZynqMP and most versions greater than r1p07 supports
TX and RX BD prefetch. The number of BDs that can be prefetched is a
HW configurable parameter. For ZynqMP, this parameter is 4.
When GEM DMA is accessing the last BD in the ring, even before the
BD is processed and the WRAP bit is noticed, it will have prefetched
BDs outside the BD ring. These will not be processed but it is
necessary to have accessible memory after the last BD. Especially
in cases where SMMU is used, memory locations immediately after the
last BD may not have translation tables triggering HRESP errors. Hence
always allocate extra BDs to accommodate for prefetch.
The value of tx/rx bd prefetch for any given SoC version is:
2 ^ (corresponding field in design config 10 register).
(value of this field >= 1)
Added a capability flag so that older IP versions that do not have
DCFG10 or this prefetch capability are not affected.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx ring is allocated for all queues in macb_alloc_consistent.
Free the same for all queues instead of just Q0.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable txq_length is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'txq_length' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem:
In vxlan_newlink, a default fdb entry is added before register_netdev.
The default fdb creation function also notifies user-space of the
fdb entry on the vxlan device which user-space does not know about yet.
(RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex).
This patch fixes the user-space netlink notification ordering issue
with the following changes:
- decouple fdb notify from fdb create.
- Move fdb notify after register_netdev.
- Call rtnl_configure_link in vxlan newlink handler to notify
userspace about the newlink before fdb notify and
hence avoiding the user-space race.
Fixes: afbd8bae9c ("vxlan: add implicit fdb entry for default destination")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new option do_notify to vxlan_fdb_destroy to make
sending netlink notify optional. Used by a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add new vxlan_fdb_alloc helper
- rename existing vxlan_fdb_create into vxlan_fdb_update:
because it really creates or updates an existing
fdb entry
- move new fdb creation into a separate vxlan_fdb_create
Main motivation for this change is to introduce the ability
to decouple vxlan fdb creation and notify, used in a later patch.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_BRIDGE_VLAN_FILTERING is disabled, gcc correctly points out
that the 'vid' variable is uninitialized whenever br_vlan_get_pvid
returns an error:
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c: In function 'mlxsw_sp_rif_vlan_fid_get':
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:6881:6: error: 'vid' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes the condition check to always return -EINVAL here,
which I guess is what the author intended here.
Fixes: e6f1960ae6 ("mlxsw: spectrum_router: Allocate FID according to PVID")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t4_get_flash_params() fails in a fatal fashion if the FLASH part isn't
one of the recognized parts. But this leads to desperate efforts to update
drivers when various FLASH parts which we are using suddenly become
unavailable and we need to substitute new FLASH parts. This has lead to
more than one Customer Field Emergency when a Customer has an old driver
and suddenly can't use newly shipped adapters.
This commit fixes this by simply assuming that the FLASH part is 4MB in
size if it can't be identified. Note that all Chelsio adapters will have
flash parts which are at least 4MB in size.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware's description, driver should not send command to
IMP while hardware doing global or core reset.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the core/global/IMP reset need clear cause, other type does not
need do it. The warning may be treated as error as it is normal. This
patch removes the warning.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hclgevf_free_vector function expects the caller to pass
the vector_id to it, and hclgevf_put_vector pass vector to
it now, which will cause vector allocation problem.
This patch fixes it by converting vector into vector_id before
calling hclgevf_free_vector.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi_alloc_skb is excepted to be called under the
non-preemptible code path when it is called by hns3_clean_rx_ring
during loopback selftest, otherwise the below warning will be
logged:
[ 92.420780] BUG: using smp_processor_id() in preemptible
[00000000] code: ethtool/1873
<SNIP>
[ 92.463202] check_preemption_disabled+0xf8/0x100
[ 92.467893] debug_smp_processor_id+0x1c/0x28
[ 92.472239] __napi_alloc_skb+0x30/0x130
[ 92.476158] hns3_clean_rx_ring+0x118/0x5f0 [hns3]
[ 92.480941] hns3_self_test+0x32c/0x4d0 [hns3]
[ 92.485375] ethtool_self_test+0xdc/0x1e8
[ 92.489372] dev_ethtool+0x1020/0x1da8
[ 92.493109] dev_ioctl+0x188/0x3a0
[ 92.496499] sock_do_ioctl+0xf4/0x208
[ 92.500148] sock_ioctl+0x228/0x3e8
[ 92.503626] do_vfs_ioctl+0xc4/0x880
[ 92.507189] SyS_ioctl+0x94/0xa8
[ 92.510404] el0_svc_naked+0x30/0x34
This patch fix it by disabling preemption when calling
hns3_clean_rx_ring during loopback selftest.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When change the mtu, the minimal frame size of mac will be set
to zero, it is incorrect. This patch fixes it by set it to the
default value.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The payload of mailbox message is 16 byte and the value of
HCLGE_MBX_MAX_ARQ_MSG_SIZE is 8. A message truncated problem will
happen when mailbox message is converted to ARQ message. This patch
replaces HCLGE_MBX_MAX_ARQ_MSG_SIZE with the size of ARQ message in
hclgevf_mbx_handler to fix this problem.
Fixes: b11a0bb231 ("net: hns3: Add mailbox support to VF driver")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware only support tcp/udp/sctp l4 checksum offload, but
the driver currently tell hardware to do l4 checksum offlad when
l3 is IPv4 or IPv6, which may cause checksumm error.
This patch fixes it by only enabling the l4 offload when l4 is
tcp/udp/sctp.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HCLGE_RX_PRIV_EN_B is used to tell the firmware whether
to update the specific waterline value, if the is not set,
the firmware will ignore the value.
This patch fixes by setting the HCLGE_RX_PRIV_EN_B even if
the updated value is zero.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When pfc pause mode is enable, the mac pause mode need to be
disabled, otherwise the pfc pause packet will not be sent when
congestion happens.
This patch fixes by disabling the mac pause when pfc pause is
enabled.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, tc related configuration is not setup when the
netdev is first up, which cause the stack only using tc 0
problem.
This patch fixes it by setting the tc related configuration
using the info from NCL_CONFIG when netdev is first up.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-1.7.2 NIC firmware does not support (and does not respond to) the "get
speed" command which is sent by the 1.7.2 driver (for CN23XX-225 cards
only) during modprobe. Due to a bug in older firmware (with respect to
unknown commands), this unsupported command causes a cascade of errors that
ends in a kernel panic.
Fix it by making the sending of the "get speed" command conditional on the
firmware version.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_set_link_ksettings() function from phylib can
be used instead of in-house ravb_set_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_get_link_ksettings() function from phylib can be
used instead of in-house ravb_get_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_ethtool_ksettings_get() call does not modify device state or device
driver state, hence there is no need to utilize a driver specific
spinlock.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_nway_reset() function from phylib can be used
instead of in-house ravb_nway_reset().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to call a heavyweight phy_start_aneg() for phy
auto-negotiation by ethtool, the phy is already initialized and
link auto-negotiation is started by calling phy_start() from
ravb_phy_start() when a network device is opened.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.
Now duplex mode setting is enforced in ravb_adjust_link() only, also
now RX/TX is disabled when link is put down or modifications to E-MAC
registers ECMR and GECMR are expected for both cases of checked and
ignored link status pin state from E-MAC interrupt handler.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.
The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_set_link_ksettings() function from phylib can
be used instead of in-house sh_eth_set_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_get_link_ksettings() function from phylib can be
used instead of in-house sh_eth_get_link_ksettings().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_ethtool_ksettings_get() call does not modify device state or device
driver state, hence there is no need to utilize a driver specific
spinlock.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic phy_ethtool_nway_reset() function from phylib can be used
instead of in-house sh_eth_nway_reset().
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to call a heavyweight phy_start_aneg() for phy
auto-negotiation by ethtool, the phy is already initialized and
link auto-negotiation is started by calling phy_start() from
sh_eth_phy_start() when a network device is opened.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change fixes sleep in atomic context bug, which is encountered
every time when link settings are changed by ethtool.
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however that helper function is
called in atomic context under a grabbed spinlock, because
phy_start_aneg() is called by phy_ethtool_ksettings_set() and by
replaced phy_ethtool_sset() helpers from phylib.
Now duplex mode setting is enforced in sh_eth_adjust_link() only,
also now RX/TX is disabled when link is put down or modifications
to E-MAC registers ECMR and GECMR are expected for both cases of
checked and ignored link status pin state from E-MAC interrupt handler.
For reference the change is a partial rework of commit 1e1b812bbe
("sh_eth: fix handling of no LINK signal").
Fixes: dc19e4e5e0 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 35b5f6b1a8 ("PHYLIB: Locking fixes for PHY I/O
potentially sleeping") phy_start_aneg() function utilizes a mutex
to serialize changes to phy state, however the helper function is
called in atomic context.
The bug can be reproduced by running "ethtool -r" command, the bug
is reported if CONFIG_DEBUG_ATOMIC_SLEEP build option is enabled.
Fixes: dc19e4e5e0 ("sh: sh_eth: Add support ethtool")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we are doing JIT, we would want to use the advanced version of the
reciprocal divide (reciprocal_value_adv) to trade performance with host.
We could reduce the required ALU instructions from 4 to 2 or 1.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
NFP doesn't have integer divide instruction, this patch use reciprocal
algorithm (the basic one, reciprocal_div) to emulate it.
For each u32 divide, we would need 11 instructions to finish the operation.
7 (for multiplication) + 4 (various ALUs) = 11
Given NFP only supports multiplication no bigger than u32, we'd require
divisor and dividend no bigger than that as well.
Also eBPF doesn't support signed divide and has enforced this on C language
level by failing compilation. However LLVM assembler hasn't enforced this,
so it is possible for negative constant to leak in as a BPF_K operand
through assembly code, we reject such cases as well.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
NFP supports u16 and u32 multiplication. Multiplication is done 8-bits per
step, therefore we need 2 steps for u16 and 4 steps for u32.
We also need one start instruction to initialize the sequence and one or
two instructions to fetch the result depending on either you need the high
halve of u32 multiplication.
For ALU64, if either operand is beyond u32's value range, we reject it. One
thing to note, if the source operand is BPF_K, then we need to check "imm"
field directly, and we'd reject it if it is negative. Because for ALU64,
"imm" (with s32 type) is expected to be sign extended to s64 which NFP mul
doesn't support. For ALU32, it is fine for "imm" be negative though,
because the result is 32-bits and here is no difference on the low halve
of result for signed/unsigned mul, so we will get correct result.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
NFP verifier hook is coping range information of the shift amount for
indirect shift operation so optimized shift sequences could be generated.
We want to use range info to do more things. For example, to decide whether
multiplication and divide are supported on the given range.
This patch simply let NFP verifier hook to copy range info for all operands
of all ALU operands.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The two fields are a copy of umin and umax info of bpf_insn->src_reg
generated by verifier.
Rename to make their meaning clear.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Setting up macvlan/macvtap networks over atlantic NIC results
in no traffic over these networks because ndo_set_rx_mode did
not listed UC MACs as registered in unicast filter.
Here we fix that taking into account maximum number of UC
filters supported by hardware. If more than MAX addresses were
registered, we just enable promisc and/or allmulti to pass
the traffic in.
We also remove MULTICAST_ADDRESS_MAX constant from aq_cfg since
thats not a configurable parameter at all.
Fixes: b21f502 ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
schedule_timeout_* takes a timeout in jiffies but the code currently is
passing in a constant which makes this timeout HZ dependent. So define
a constant with (hopefully) meaningful name and pass it through
msecs_to_jiffies() to fix the HZ dependency.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
commit f21fb3ed36 ("Add support of Cavium Liquidio ethernet adapters")
Acked-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the USB id of LTE modem Quectel EG91. It requires the
same quirk as other Quectel modems to make it work.
Signed-off-by: Matevz Vucnik <vucnikm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'chip_ver' rather than 'chip' to check if the card
is T5.
Fixes: e8d452923a ("cxgb4: clean up init_one")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If format_idx == s_mcp_trace_meta.formats_num then we read one element
beyond the end of the s_mcp_trace_meta.formats[] array.
Fixes: 50bc60cb15 ("qed*: Utilize FW 8.33.11.0")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables adv and lpa are being assigned but are never used hence they
are redundant and can be removed. Also remove the unncessary mii_reads
too.
Cleans up clang warnings:
warning: variable 'lpa' set but not used [-Wunused-but-set-variable]
warning: variable 'adv' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both SFC and SFC_FALCON depend on NET_VENDOR_SOLARFLARE, hence use the
latter to decide whether to descend into the sfc subdirectory.
Move the rule to descend into sfc/falcon to the sfc subdirectory.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vendor guard Kconfig symbols for Cadence and Packet Engines use a
"NET_" prefix, while all other vendor guards use a "NET_VENDOR_"
prefix. Hence make them consistent with the rest, and add the missing
trailing "S" for Packet Engines while at it.
As these options don't directly affect the kernel build, and default to
"y", this change has no impact on kernels built with existing
(def)configs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling NET_VENDOR_* Kconfig options does not directly affect the
kernel build. Hence NET_VENDOR_AURORA should default to yes, like other
NET_VENDOR_* options.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables consumer, cmd_desc, end_cnt and no_of_desc are being assigned
but are never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'consumer' set but not used [-Wunused-but-set-variable]
warning: variable 'cmd_desc' set but not used [-Wunused-but-set-variable]
warning: variable 'end_cnt' set but not used [-Wunused-but-set-variable]
warning: variable 'no_of_desc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create initial devlink parameters table for bnxt_en.
Table consists of a permanent generic parameter.
enable_sriov - Enables Single-Root Input/Output Virtualization(SR-IOV)
characteristic of the device.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mlx4_devlink_reload() to support devlink reload operation.
Add mlx4_devlink_param_load_driverinit_values() to load values which
were set using driverinit configuration mode.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create initial parameters table for mlx4.
The table consists of two generic parameters and two driver-specific
parameters.
Generic:
internal_err_reset - Enable reset device on internal errors. This
parameter can be configured on mlx4 either on runtime or during driver
initialization.
max_macs - Max number of MACs per ETH port. For mlx4 this parameter
value range is between 1 and 128. This parameter can be configured on
mlx4 only during driver initialization.
Driver specific:
enable_64b_cqe_eqe - Enable 64 byte CQEs/EQEs when the FW supports it.
This parameter can be configured on mlx4 only during driver
initialization.
enable_4k_uar - Enable using 4K UAR. This parameter can be configured on
mlx4 only during driver initialization.
Register the parameters table on mlx4_init_one() and unregister on
mlx4_remove_one().
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable channel is being assigned but is never used hence it is
redundant and can be removed.
Cleans up two clang warnings:
warning: variable 'channel' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables my_epid and max_epid are currently assigned and not being
used - however, I suspect they were intended to be used in the for-loops
to reduce the dereferencing of hw. Replace hw->my_epid and hw->max_epid
with these variables.
Cleans up clang warnings:
warning: variable 'my_epid' set but not used [-Wunused-but-set-variable]
variable 'max_epid' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer skb is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'skb' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer ndev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'ndev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:525:5: warning:
symbol 'hw_atl_utils_mpi_set_speed' was not declared. Should it be static?
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:536:5: warning:
symbol 'hw_atl_utils_mpi_set_state' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/dsa/vitesse-vsc73xx.c:1054:6: warning:
symbol 'vsc73xx_get_strings' was not declared. Should it be static?
drivers/net/dsa/vitesse-vsc73xx.c:1113:5: warning:
symbol 'vsc73xx_get_sset_count' was not declared. Should it be static?
drivers/net/dsa/vitesse-vsc73xx.c:1122:6: warning:
symbol 'vsc73xx_get_ethtool_stats' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_err error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without CONFIG_GPIOLIB, some headers are not included implicitly,
leading to a build failure:
drivers/net/ieee802154/mcr20a.c: In function 'mcr20a_probe':
drivers/net/ieee802154/mcr20a.c:1347:13: error: implicit declaration of function 'irq_get_trigger_type'; did you mean 'irq_get_irqchip_state'? [-Werror=implicit-function-declaration]
This includes gpio/consumer.h and irq.h directly rather through the
gpiolib header.
Fixes: 8c6ad9cc51 ("ieee802154: Add NXP MCR20A IEEE 802.15.4 transceiver driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Xue Liu <liuxuenetmail@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Configuration information read at driver load can become stale after it is
updated. Mark information as not valid and re-populate when this happens.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When runtime-suspending we configure WoL w/o touching saved_wolopts.
If saved_wolopts == 0 we would power down the PHY in this case what's
wrong. Therefore we have to check the actual chip WoL settings here.
Fixes: 433f9d0ddc ("r8169: improve saved_wolopts handling")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In highly constrained resources environments (like the 124VF
T5 and 248VF T6 configurations), PF4 may not have very many
resources at all and we need to adapt to whatever we've been
allocated, this patch adds support to get the provisioned
resources.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently also the pause flags are removed from phydev->supported because
they're not included in PHY_DEFAULT_FEATURES. I don't think this is
intended, especially when considering that this function can be called
via phy_set_max_speed() anywhere in a driver. Change the masking to mask
out only the values we're going to change. In addition remove the
misleading comment, job of this small function is just to adjust the
supported and advertised speeds.
Fixes: f3a6bd393c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_core_dump_fill_mkey() is going to be used in next
patch in IB and doesn't need to be visible to whole
mlx5_core. Move that command to mlx5_ib.
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Add sw pattern detector statistics to mt76x2 debugfs.
Moreover track down number of allocated sequence by the detector
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add sw DFS pattern detector support for mt76x2 based devices.
Dfs pattern supported:
- short pulse radar patterns
- staggered radar patterns
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce sw event ring buffer to queue DFS pulses loaded from the hw.
Radar pulses will be used in DFS sw detector
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add mt76_{incr,decr} utility routines to increment/decrement a value
with wrap-around (they will be used by mt76x2 DFS sw detector)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'firmware' is a module param which may been longer than firmware_id,
so using strlcpy() to guard against overflows. Also priv is allocated
with zeroed memory,no need to set firmware_id[0] to '\0'.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case memory resources for *events_vector* were allocated, release
them before return.
Addresses-Coverity-ID: 1470194 ("Resource leak")
Fixes: 4ec7cece87 ("wlcore: Add missing PM call for wlcore_cmd_wait_for_event_or_timeout()")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Prior to commit 573185cc7e ("mmc: core: Invoke sdio func driver's PM
callbacks from the sdio bus"), the MMC core used to call into the power
management functions of SDIO clients itself and removed the card if the
return code was non-zero. IOW, the mmc handled errors gracefully and didn't
upchain them to the pm core.
Since this change, the mmc core relies on generic power management
functions which treat all errors as a reason to cancel the suspend
immediately. This causes suspend attempts to fail when the libertas
driver is loaded.
To fix this, power down the card explicitly in if_sdio_suspend() when we
know we're about to lose power and return success. Also set a flag in these
cases, and power up the card again in if_sdio_resume().
Fixes: 573185cc7e ("mmc: core: Invoke sdio func driver's PM callbacks from the sdio bus")
Cc: <stable@vger.kernel.org>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Chris Ball <chris@printf.net>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
That struct is used when querying firmware for the STA. It seem is has
been changing during the time. Luckily its format seems to be backward
compatible starting with v2 (the only breakage was v1 -> v2).
The version that was supported by brcmfmac so far was v4. It was what
43602a1 and 4366b1 firmwares (7.35.177.56 and 10.10.69.3309 accordingly)
were using. It also seems to be used by early 4366c0 firmwares
(10.10.69.6908 and 10.10.69.69017).
The problem appears when switching to the 10.10.122.20 firmware. It uses
v5 and instead of falling back to v4 when submitted buffer isn't big
enough it fallbacks to the v3.
To receive all v4 specific info with the newest firmware we have to
submit a struct (buffer) that matches v5.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
That struct is passed by a firmware when querying for STA info. Flags
are used to indicate what info could be obtained.
These new defines may allow passing more info to the cfg80211 in the
future. They had been obtained from Broadcom's SDK file wlioctl_defs.h
used by DD-WRT.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New Broadcom firmwares mark monitor mode packets using a newly defined
bit in the flags field. Use it to filter them out and pass to the
monitor interface. These defines were found in bcmmsgbuf.h from SDK.
As not every firmware generates radiotap header this commit introduces
BRCMF_FEAT_MONITOR_FMT_RADIOTAP flag. It has to be has based on firmware
capabilities. If not present brcmf_netif_mon_rx() will assume packet is
a raw 802.11 frame and will prepend it with an empty radiotap header.
This new code is limited to the msgbuf protocol at this point. Adding
support for SDIO/USB devices will require some extra work (possibly a
new firmware release).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Depending on used build-time options some firmwares may already include
radiotap header in passed monitor frames. Add a new feature flag to
store info about it. It's needed for proper handling of received frames
before passing them up.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Many/most of firmwares support creating monitor interface but only the
most recent ones explicitly /announce/ it using a "monitor" entry in the
list of capabilities.
Check for that entry and store internally info about monitor mode
support using a new feature flag. Once we sort out all details of
handling monitor interface it will be used when reporting available
interfaces to the cfg80211.
Later some fallback detecion method may be added for older firmwares.
For now just stick to the "monitor" capability which should be 100%
reliable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable 'irq' is being assigned but is never used hence it is
and can be removed.
Cleans up clang warning:
warning: variable 'irq' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable old_vlan is being assigned but is never used hence it is
and can be removed.
Cleans up clang warning:
warning: variable 'old_vlan' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer 'name' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'name' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer 'info' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'info' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer pfhwdev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'pfhwdev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'protocol' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'protocol' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable last_rule_idx is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'last_rule_idx' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'inc' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'inc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer req and variable func are being assigned but are never used
hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'req' set but not used [-Wunused-but-set-variable]
warning: variable 'func' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'freed' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'freed' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer rxd is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'rxb' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable old_duplex is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'old_duplex' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer rxdesc is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'rxdesc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'off' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'off' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement HW offload support for SO_TXTIME through igb's Launchtime
feature. This is done by extending igb_setup_tc() so it supports
TC_SETUP_QDISC_ETF and configuring i210 so time based transmit
arbitration is enabled.
The FQTSS transmission mode added before is extended so strict
priority (SP) queues wait for stream reservation (SR) ones.
igb_config_tx_modes() is extended so it can support enabling/disabling
Launchtime following the previous approach used for the credit-based
shaper (CBS).
As the previous flow, FQTSS transmission mode is enabled automatically
by the driver once Launchtime (or CBS, as before) is enabled.
Similarly, it's automatically disabled when the feature is disabled
for the last queue that had it setup on.
The driver just consumes the transmit times from the skbuffs directly,
so no special handling is done in case an 'invalid' time is provided.
We assume this has been handled by the ETF qdisc already.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, skb_tx_timestamp() is being called before the Tx
descriptors are prepared in igb_xmit_frame_ring(), which happens
during either the igb_tso() or igb_tx_csum() calls.
Given that now the skb->tstamp might be used to carry the timestamp
for SO_TXTIME, we must only call skb_tx_timestamp() after the
information has been copied into the Tx descriptors.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split code into a separate function (igb_offload_apply()) that will be
used by ETF offload implementation.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the data transmission arbitration algorithm - DataTranARB
field on TQAVCTRL reg - is always set to CBS when the Tx mode is
changed from legacy to 'Qav' mode.
Make that configuration a bit more granular in preparation for the
upcoming Launchtime enabling patches, since CBS and Launchtime can be
enabled separately. That is achieved by moving the DataTranARB setup
to igb_config_tx_modes() instead.
Similarly, when disabling CBS we must check if it has been disabled
for all queues, and clear the DataTranARB accordingly.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this function retrieve what it needs from the Tx ring being
addressed since it already relies on what had been saved on it before.
Also, since this function will be used by the upcoming Launchtime
patches rename it to better reflect its intention. Note that
Launchtime is not part of what 802.1Qav specifies, but the i210
datasheet refers to this set of functionality as "Qav Transmission
Mode".
Here we also perform a tiny refactor at is_any_cbs_enabled(), and add
further documentation to igb_setup_tx_mode().
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain conditions, the device may not be able to link in gigabit mode. This software workaround ensures that the device will not enter the failure state.
Fixes: d0cad87170 ("SMSC75XX USB 2.0 Gigabit Ethernet Devices")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Embedded use where e.g. AX88772B chips may be used without external
EEPROMs the boot loader may choose to pass the MAC address to be used
via device tree. Therefore, allow for optionally getting the MAC
address from device tree data e.g. as follows (excerpt from a T30 based
board, local-mac-address to be filled in by boot loader):
/* EHCI instance 1: USB2_DP/N -> AX88772B */
usb@7d004000 {
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
asix@1 {
reg = <1>;
local-mac-address = [00 00 00 00 00 00];
};
};
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NetworkManager likes to manage linklocal prefix routes and does so with
the NLM_F_APPEND flag, breaking attempts to simplify the IPv6 route
code and by extension enable multipath routes with device only nexthops.
Revert f34436a430 and these followup patches:
6eba08c362 ("ipv6: Only emit append events for appended routes").
ce45bded64 ("mlxsw: spectrum_router: Align with new route replace logic")
53b562df8c ("mlxsw: spectrum_router: Allow appending to dev-only routes")
Update the fib_tests cases to reflect the old behavior.
Fixes: f34436a430 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: David Ahern <dsahern@gmail.com>
Improves packet rate of 1-byte UDP receives by up to 10%.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The m88e1121 LED default configuration does not apply m88e151x.
So add a function to relpace m88e1121 LED configuration.
Signed-off-by: Wang Dongsheng <dongsheng.wang@hxt-semitech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a DSA driver for:
Vitesse VSC7385 SparX-G5 5-port Integrated Gigabit Ethernet Switch
Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch
Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch
Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch
These switches have a built-in 8051 CPU and can download and execute
firmware in this CPU. They can also be configured to use an external
CPU handling the switch in a memory-mapped manner by connecting to
that external CPU's memory bus.
This driver (currently) only takes control of the switch chip over
SPI and configures it to route packages around when connected to a
CPU port. The chip has embedded PHYs and VLAN support so we model it
using DSA as a best fit so we can easily add VLAN support and maybe
later also exploit the internal frame header to get more direct
control over the switch.
The four built-in GPIO lines are exposed using a standard GPIO chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7385, VSC7388, VSC7395 and VSC7398 are integrated
switch/router chips for 5+1 or 8-port switches/routers. When
managed directly by Linux using DSA we need to do a special
set-up "dance" on the PHY. Unfortunately these sequences
switches the PHY to undocumented pages named 2a30 and 52b6
and does undocumented things. It is described by these opaque
sequences also in the reference manual. This is a best
effort to integrate it anyways.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-07-03
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Various improvements to bpftool and libbpf, that is, bpftool build
speed improvements, missing BPF program types added for detection
by section name, ability to load programs from '.text' section is
made to work again, and better bash completion handling, from Jakub.
2) Improvements to nfp JIT's map read handling which allows for optimizing
memcpy from map to packet, from Jiong.
3) New BPF sample is added which demonstrates XDP in combination with
bpf_perf_event_output() helper to sample packets on all CPUs, from Toke.
4) Add a new BPF kselftest case for tracking connect(2) BPF hooks
infrastructure in combination with TFO, from Andrey.
5) Extend the XDP/BPF xdp_rxq_info sample code with a cmdline option to
read payload from packet data in order to use it for benchmarking.
Also for '--action XDP_TX' option implement swapping of MAC addresses
to avoid drops on some hardware seen during testing, from Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of fixes for 4.18 and for numerous drivers. Something to mention
about is the wcn36xx fix which makes it possible to compile with gcc older than
4.4 (though I'm not sure if we even support those anymore).
qtnfmac
* coverity fix for a new commit in v4.18-rc1
rtlwifi
* fix kernel oops during driver removal
* fix firmware image corruption for rtl8821ae
brcmfmac
* fix crash if there's no firmware image
mwifiex
* a revert and a better fix for a new commit v4.18-rc1
mt7601u
* fix a recent regression about unnecessary warning about avg_rssi
wcn36xx
* convert testmode.c to plain ASCII
ath10k
* fix a firmware crash during bandwidth change
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbO1LKAAoJEG4XJFUm622bPEgH/jJ552p5KdOFkwtKWQ9sybKP
53yCEJw0sjaKVaXdPbOLZQP4ioJ0xYiOxKN1LBmBg2AVFKvnSp5LRWwmpzqdpOoE
oYo09wcSE5Q7AFHaWDmV5/6ze/S1Aem9B5iNdS/hScuXqsnqct17RVO1zVWpHnU5
W8+qVFrBcbqrvuTDdGo5GBaUQBeRHpIpGjABBk7D6qXVwOtzr2ibKGRHRITu3yYo
vA+IF+S+IwWEITt4AxaN728sk6Q3S9r5kBmRlyzlfeSmT8S/zS8Hid5P2eQz6Dv4
Ib22ZvBVFyKQd4qeXYG1lWxbTQrNZIY3JUDGkcdhkhdb3TKYL37x3mWP2LoTpK4=
=0sGc
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-07-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.18
First set of fixes for 4.18 and for numerous drivers. Something to mention
about is the wcn36xx fix which makes it possible to compile with gcc older than
4.4 (though I'm not sure if we even support those anymore).
qtnfmac
* coverity fix for a new commit in v4.18-rc1
rtlwifi
* fix kernel oops during driver removal
* fix firmware image corruption for rtl8821ae
brcmfmac
* fix crash if there's no firmware image
mwifiex
* a revert and a better fix for a new commit v4.18-rc1
mt7601u
* fix a recent regression about unnecessary warning about avg_rssi
wcn36xx
* convert testmode.c to plain ASCII
ath10k
* fix a firmware crash during bandwidth change
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Network core refuses to change mac address because flag
IFF_LIVE_ADDR_CHANGE isn't set. Set this missing flag.
Fixes: 1f7aa2bc26 ("r8169: simplify rtl_set_mac_address")
Reported-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds ethtool -r|--negotiate operation support. It triggers special
control bit on FW interface causing FW to restart link negotiation.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Anton Mikaev <amikaev@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
