B.A.T.M.A.N. IV requires the number of rebroadcast from a neighboring
originator. These statistics are gathered per interface which transmitted
the OGM (and then received it again). Since an originator is not interface
specific, a resizable array was used in each originator.
This resizable array had an entry for each interface and had to be resizes
(for all OGMs) when the number of active interface was modified. This could
cause problems when a large number of interface is added and not enough
continuous memory is available to allocate the array.
There is already a per interface originator structure "batadv_orig_ifinfo"
which can be used to store this information.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A reference for the best gateway is taken when the list of gateways in the
mesh is sent via netlink. This is necessary to check whether the currently
dumped entry is the currently selected gateway or not. This information is
then transferred as flag BATADV_ATTR_FLAG_BEST.
After the comparison of the current entry is done,
batadv_iv_gw_dump_entry() has to decrease the reference counter again.
Otherwise the reference will be held and thus prevents a proper shutdown of
the batman-adv interfaces (and some of the interfaces enslaved in it).
Fixes: efb766af06 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations")
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Tested-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
batman-adv uses internal indices for each enabled and active interface.
It is currently used by the B.A.T.M.A.N. IV algorithm to identifify the
correct position in the ogm_cnt bitmaps.
The type for the number of enabled interfaces (which defines the next
interface index) was set to char. This type can be (depending on the
architecture) either signed (limiting batman-adv to 127 active slave
interfaces) or unsigned (limiting batman-adv to 255 active slave
interfaces).
This limit was not correctly checked when an interface was enabled and thus
an overflow happened. This was only catched on systems with the signed char
type when the B.A.T.M.A.N. IV code tried to resize its counter arrays with
a negative size.
The if_num interface index was only a s16 and therefore significantly
smaller than the ifindex (int) used by the code net code.
Both &batadv_hard_iface->if_num and &batadv_priv->num_ifaces must be
(unsigned) int to support the same number of slave interfaces as the net
core code. And the interface activation code must check the number of
active slave interfaces to avoid integer overflows.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_iv_gw_dump stops the processing loop when
batadv_iv_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.
Fixes: efb766af06 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The header file is used by different userspace programs to inject packets
or to decode sniffed packets. It should therefore be available to them as
userspace header.
Also other components in the kernel (like the flow dissector) require
access to the packet definitions to be able to decode ETH_P_BATMAN ethernet
packets.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- de-inline hash functions to save memory footprint, by Denys Vlasenko
- Add License information to various files, by Sven Eckelmann (3 patches)
- Change batman_adv.h from ISC to MIT, by Sven Eckelmann
- Improve various includes, by Sven Eckelmann (5 patches)
- Lots of kernel-doc work by Sven Eckelmann (8 patches)
-----BEGIN PGP SIGNATURE-----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=5JUK
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20171220' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- de-inline hash functions to save memory footprint, by Denys Vlasenko
- Add License information to various files, by Sven Eckelmann (3 patches)
- Change batman_adv.h from ISC to MIT, by Sven Eckelmann
- Improve various includes, by Sven Eckelmann (5 patches)
- Lots of kernel-doc work by Sven Eckelmann (8 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the kernel-doc documentation, externally visible functions
should be documented. This refers to all all non-static function which can
(and will) be used by functions in other sources files.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The inline kernel-doc comments make it easier to keep changes to the
struct/enum synchronized with the documentation of the it. And it makes it
easier for larger structures like struct batadv_priv to read the
documentation inside the code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The documentation describing kernel-doc comments for functions ("How to
format kernel-doc comments") uses parentheses at the end of the function
name. Using this format allows to use a consistent style when adding
documentation to a function and when referencing this function in a
different kernel-doc section.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The linux/gfp.h provides the GFP_ATOMIC and GFP_KERNEL define. It should
therefore be included instead of linux/fs.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The "Linux kernel licensing rules" require that each file has a SPDX
license identifier as first line (and sometimes as second line).
The FSFE REUSE practices [1] would also require the same tags but have no
restrictions on the placement in the source file. Using the "Linux kernel
licensing rules" is therefore also fulfilling the FSFE REUSE practices
requirements at the same time.
[1] https://reuse.software/practices/
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The originator node object orig_neigh_node is used to when accessing the
bcast_own(_sum) and real_packet_count information. The access to them has
to be protected with the spinlock in orig_neigh_node.
But the function uses the lock in orig_node instead. This is incorrect
because they could be two different originator node objects.
Fixes: 0ede9f41b2 ("batman-adv: protect bit operations to count OGMs with spinlock")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
checkpatch introduced with commit 63b7c73ec8 ("checkpatch: add --strict
check for ifs with unnecessary parentheses") an additional test which
identifies some unnecessary parentheses.
Remove these unnecessary parentheses to avoid the warnings and to unify the
coding style slightly more.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
skb_put_data makes it unnecessary to store the skb_put return value to copy
some data to the packet. The returned pointer of skb_put_data should
therefore not stored by functions which previously only used it to copy
some data.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The string representation for a mac address produced by %pM is 17
characters long. Left-aligning the output in a 15 character wide field
width %-15pM is therefore misleading and unnecessary.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function names in batman-adv changed slightly in the past. But some of
the debug messages were not updated correctly and therefore some messages
were incorrect. To avoid this in the future, these kind of messages should
use __func__ to automatically print the correct function name.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Two single characters (line breaks) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
- bump version strings, by Simon Wunderlich
- Code and Style cleanups, by Sven Eckelmann (5 patches)
- Remove an unneccessary memset, by Tobias Klauser
- DAT and BLA optimizations for various corner cases, by Andreas Pape
(5 patches)
- forward/rebroadcast packet restructuring, by Linus Luessing
(2 patches)
- ethtool cleanup and remove unncessary code, by Sven Eckelmann
(4 patches)
- use net_device_stats from net_device instead of private copy,
by Tobias Klauser
-----BEGIN PGP SIGNATURE-----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=r99K
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20170406' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Code and Style cleanups, by Sven Eckelmann (5 patches)
- Remove an unneccessary memset, by Tobias Klauser
- DAT and BLA optimizations for various corner cases, by Andreas Pape
(5 patches)
- forward/rebroadcast packet restructuring, by Linus Luessing
(2 patches)
- ethtool cleanup and remove unncessary code, by Sven Eckelmann
(4 patches)
- use net_device_stats from net_device instead of private copy,
by Tobias Klauser
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An skb is assigned to a forw_packet only once, shortly after the
forw_packet allocation.
With this patch the assignment is moved into the this allocation
function.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
- Keep fragments equally sized, avoids some problems with too small fragments,
by Sven Eckelmann
- Initialize gateway class correctly when BATMAN V is compiled in,
by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=zGdm
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20170316' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfixes:
- Keep fragments equally sized, avoids some problems with too small fragments,
by Sven Eckelmann
- Initialize gateway class correctly when BATMAN V is compiled in,
by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The gateway selection class variable is shared between different algorithm
versions. But the interpretation of the content is algorithm specific. The
initialization is therefore also algorithm specific.
But this was implemented incorrectly and the initialization for BATMAN_V
always overwrote the value previously written for BATMAN_IV. This could
only be avoided when BATMAN_V was disabled during compile time.
Using a special batadv_algo hook for this initialization avoids this
problem.
Fixes: 50164d8f50 ("batman-adv: B.A.T.M.A.N. V - implement GW selection logic")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In rare cases during shutdown the following general protection fault can
happen:
general protection fault: 0000 [#1] SMP
Modules linked in: batman_adv(O-) [...]
CPU: 3 PID: 1714 Comm: rmmod Tainted: G O 4.6.0-rc6+ #1
[...]
Call Trace:
[<ffffffffa0363294>] batadv_hardif_disable_interface+0x29a/0x3a6 [batman_adv]
[<ffffffffa0373db4>] batadv_softif_destroy_netlink+0x4b/0xa4 [batman_adv]
[<ffffffff813b52f3>] __rtnl_link_unregister+0x48/0x92
[<ffffffff813b9240>] rtnl_link_unregister+0xc1/0xdb
[<ffffffff8108547c>] ? bit_waitqueue+0x87/0x87
[<ffffffffa03850d2>] batadv_exit+0x1a/0xf48 [batman_adv]
[<ffffffff810c26f9>] SyS_delete_module+0x136/0x1b0
[<ffffffff8144dc65>] entry_SYSCALL_64_fastpath+0x18/0xa8
[<ffffffff8108aaca>] ? trace_hardirqs_off_caller+0x37/0xa6
Code: 89 f7 e8 21 bd 0d e1 4d 85 e4 75 0e 31 f6 48 c7 c7 50 d7 3b a0 e8 50 16 f2 e0 49 8b 9c 24 28 01 00 00 48 85 db 0f 84 b2 00 00 00 <48> 8b 03 4d 85 ed 48 89 45 c8 74 09 4c 39 ab f8 00 00 00 75 1c
RIP [<ffffffffa0371852>] batadv_purge_outstanding_packets+0x1c8/0x291 [batman_adv]
RSP <ffff88001da5fd78>
---[ end trace 803b9bdc6a4a952b ]---
Kernel panic - not syncing: Fatal exception in interrupt
Kernel Offset: disabled
---[ end Kernel panic - not syncing: Fatal exception in interrupt
It does not happen often, but may potentially happen when frequently
shutting down and reinitializing an interface. With some carefully
placed msleep()s/mdelay()s it can be reproduced easily.
The issue is, that on interface removal, any still running worker thread
of a forwarding packet will race with the interface purging routine to
free a forwarding packet. Temporarily giving up a spin-lock to be able
to sleep in the purging routine is not safe.
Furthermore, there is a potential general protection fault not just for
the purging side shown above, but also on the worker side: Temporarily
removing a forw_packet from the according forw_{bcast,bat}_list will make
it impossible for the purging routine to catch and cancel it.
# How this patch tries to fix it:
With this patch we split the queue purging into three steps: Step 1),
removing forward packets from the queue of an interface and by that
claim it as our responsibility to free.
Step 2), we are either lucky to cancel a pending worker before it starts
to run. Or if it is already running, we wait and let it do its thing,
except two things:
Through the claiming in step 1) we prevent workers from a) re-arming
themselves. And b) prevent workers from freeing packets which we still
hold in the interface purging routine.
Finally, step 3, we are sure that no forwarding packets are pending or
even running anymore on the interface to remove. We can then safely free
the claimed forwarding packets.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batman-adv is requiring the type of wifi device in different contexts. Some
of them can take the rtnl semaphore and some of them already have the
semaphore taken. But even others don't allow that the semaphore will be
taken.
The data has to be retrieved when the hardif is added to batman-adv because
some of the wifi information for an hardif will only be available with rtnl
lock. It can then be cached in the batadv_hard_iface and the functions
is_wifi_netdev and is_cfg80211_netdev can just compare the correct bits
without imposing extra locking requirements.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Receiving functions in Linux consume the supplied skbuff. Doing the same in
the batadv_rx_handler functions makes the behavior more similar to the rest
of the Linux network code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
kfree_skb assumes that an skb is dropped after an failure and notes that.
consume_skb should be used in non-failure situations. Such information is
important for dropmonitor netlink which tells how many packets were dropped
and where this drop happened.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv codebase is using "list" for the list node (prev/next) and
<list content descriptor>+"_list" for the head of a list. Not using this
naming scheme can up in confusions when reading the code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The files provided by batman-adv via debugfs are currently converted to
netlink. Tools which are not yet converted to use the netlink interface may
still rely on the old debugfs files. But systems which already upgraded
their tools can save some space by disabling this feature. The default
configuration of batman-adv on amd64 can reduce the size of the module by
around 11% when this feature is disabled.
$ size net/batman-adv/batman-adv.ko*
text data bss dec hex filename
150507 10395 4160 165062 284c6 net/batman-adv/batman-adv.ko.y
137106 7099 2112 146317 23b8d net/batman-adv/batman-adv.ko.n
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Dump the list of gateways via the netlink socket.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: integrate in batadv_algo_ops]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This patch abstracts the forward packet creation into the new function
batadv_forw_packet_alloc().
The queue counting and interface reference counters are now handled
internally within batadv_forw_packet_alloc() and its
batadv_forw_packet_free() counterpart. This should reduce the risk of
having reference/queue counting bugs again and should increase
code readibility.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The difference between tq1 and tq2 are calculated the same way in two
separate functions.
This patch moves the common code to a separate function
'batadv_iv_ogm_neigh_diff' which handles everything necessary. The other
two functions can then handle errors and use the difference directly.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[sven@narfation.org: rebased on current version, initialize return variable
in batadv_iv_ogm_neigh_diff, add kerneldoc, convert to bool return type]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Each routing protocol may have its own specific logic about
gateway election which is potentially based on the metric being
used.
Create two GW specific API functions and move the current election
logic in the B.A.T.M.A.N. IV specific code.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The routing API data structure contains several function
pointers that can easily be grouped together based on the
component they work with.
Split the API in subobjects in order to improve definition readability.
At the same time, remove the "bat_" prefix from the API object and
its fields names. These are batman-adv private structs and there is no
need to always prepend such prefix, which only makes function invocations
much much longer.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The bat_algo.h had some functions declared which were not part of the
bat_algo.c file. These are instead stored in bat_v.c and bat_iv_ogm.c. The
declaration should therefore be also in bat_v.h and bat_iv_ogm,h to make
them easier to find.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
There are several places in batman-adv which provide logging related
functions. These should be grouped together in the log.* files to make them
easier to find.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The tvlv functionality in main.c is mostly unrelated to the rest of the
content. It still takes up a large portion of this source file (~45%, 588
lines). Moving it to a separate file makes it better visible as a main
component of the batman-adv implementation and hides it less in the other
helper functions in main.c
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[sven@narfation.org: fix conflicts with current version, fix includes,
rewrote commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is easier to detect if a include is already there for a used
functionality when the includes are ordered. Using an alphabetic order
together with the grouping in commit 1e2c2a4fe4 ("batman-adv: Add
required includes to all files") makes includes better manageable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The ogm_emit and ogm_schedule API calls were rather tight to the
B.A.T.M.A.N. IV logic and therefore rather difficult to use
with other algorithm implementations.
Remove such calls and move the surrounding logic into the
B.A.T.M.A.N. IV specific code.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The undefined behavior sanatizer detected an signed integer overflow in a
setup with near perfect link quality
UBSAN: Undefined behaviour in net/batman-adv/bat_iv_ogm.c:1246:25
signed integer overflow:
8713350 * 255 cannot be represented in type 'int'
The problems happens because the calculation of mixed unsigned and signed
integers resulted in an integer multiplication.
batadv_ogm_packet::tq (u8 255)
* tq_own (u8 255)
* tq_asym_penalty (int 134; max 255)
* tq_iface_penalty (int 255; max 255)
The tq_iface_penalty, tq_asym_penalty and inv_asym_penalty can just be
changed to unsigned int because they are not expected to become negative.
Fixes: c039876892 ("batman-adv: add WiFi penalty")
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The function batadv_iv_ogm_orig_add_if allocates new buffers for bcast_own
and bcast_own_sum. It is expected that these buffers are unchanged in case
either bcast_own or bcast_own_sum couldn't be resized.
But the error handling of this function frees the already resized buffer
for bcast_own when the allocation of the new bcast_own_sum buffer failed.
This will lead to an invalid memory access when some code will try to
access bcast_own.
Instead the resized new bcast_own buffer has to be kept. This will not lead
to problems because the size of the buffer was only increased and therefore
no user of the buffer will try to access bytes outside of the new buffer.
Fixes: d0015fdd3d ("batman-adv: provide orig_node routing API")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
It is easier to understand that the returned value of a specific function
doesn't have to be 0 when the functions was successful when the actual
return type is bool. This is especially true when all surrounding functions
with return type int use negative values to return the error code.
Reported-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The callers of the functions using batadv_hard_iface objects already make
sure that they hold a valid reference. The subfunctions don't have
to check whether the reference counter is > 0 because this was checked by
the callers.
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
The batadv_hardif_list list is checked in many situations and the items
in this list are given to specialized functions to modify the routing
behavior. At the moment each of these called functions has to check
itself whether the received batadv_hard_iface has a refcount > 0 before
it can increase the reference counter and use it in other objects.
This can easily lead to problems because it is not easily visible where
all callers of a function got the batadv_hard_iface object from and
whether they already hold a valid reference.
Checking the reference counter directly before calling a subfunction
with a pointer from the batadv_hardif_list avoids this problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
