Enable HS400 of SDHI3 using the corresponding DT property.
No further changes are required.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
There are two regulator1 nodes in the Ebisu DTS right now, one 3.3V for
the eMMC and one 12V for the backlight. This causes one to be overwritten
by the other, ultimatelly resulting in inoperable eMMC, which depends on
the former. Fix this by renumbering the backlight regulator to regulator2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: 9d16c4a10e ("arm64: dts: renesas: r8a77990: ebisu: Add backlight")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Ebisu board is using simple-scu-audio-card
which is used for Sampling Rate Convert, or MIXer, etc.
But, Ebisu is not using such feature.
Then, simple-audio-card is very enough.
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal delay mode doesn't support
on R-Car E3. This patch fixes EthernetAVB phy mode to rgmii.
This is achieved by simply dropping the phy-mode property from
r8a77990-ebisu.dts as the default property for this for r8a77990,
as set in r8a77990.dtsi, is "rgmii".
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Add the backlight device for the LVDS1 output, in preparation for panel
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds CAN0,1 and CANFD device nodes for the r8a77990 SoC
and enables CANFD connected to CN10 on the E3 Ebisu board using the
R8A77990 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PCI express channel 0 device node to the R8A77990 SoC
and enables PCIEC0 PCI express controller on the Ebisu board.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds SDHI{0,1,3} device nodes for the r8a77990 SoC
and enables SD card slot connected to SDHI0, micro SD card slot
connected to SDHI1 and eMMC connected to SDHI3 on the Ebisu board
using the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds pin control for SCIF2 on R8A77990 E3 Ebisu.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables Audio for the Ebisu board on R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: rebased]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds/enables USB2.0 peripheral for R-Car [DE]3 boards.
R-Car E3 Ebisu board connects the ID pin to the SoC, so this adds
a group "usb0_id" into usb0_pins node. Also, to use SW15 pin 3 side,
this patch adds vbus0_usb2 node on r8a77990-ebisu.dts.
R-Car D3 Draak board doesn't connect the ID pin, so this adds
"renesas,no-otg-pins" property into usb2_phy0 node.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the LVDS decoder, HDMI encoder, VGA encoder and HDMI and VGA
connectors, and wire up the display-related nodes with clocks, pinmux
and regulators.
The LVDS0 and LVDS1 encoders can use the DU_DOTCLKIN0, DU_DOTCLKIN1 and
EXTAL externals clocks. Two of them are provided to the SoC on the Ebisu
board, hook them up in DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add HDMI and CVBS inputs device nodes to R-Car E3 Ebisu board.
Both HDMI and CVBS inputs are connected to an ADV7482 video decoder hooked to
the SoC CSI-2 receiver port.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds PWM device nodes and enables PWM3 and PWM5 for
R-Car E3 Ebisu board. These devices are used for backlight control.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds and USB3.0 host device node and enable it for
R-Car E3 Ebisu board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds USB2.0 PHY and Host(EHCI/OHCI) nodes and
enables them for R-Car E3 Ebisu board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (WDT) controller on the
R8A77990 SoC, and enable the watchdog on the Ebisu board.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Squashed 2 commits]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables EthernetAVB for r8a77990 Ebisu board.
Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the Renesas Ebisu board based on R-Car E3:
- Memory,
- Main crystal,
- Serial console,
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[shimoda: rebase and add SPDX-License-Identifier]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
