ctinfo is a new tc filter action module. It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths. At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.
The DSCP restore mode:
This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.
The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links. Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.
Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway. Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.
Parameters related to DSCP restore mode:
dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.
statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask. This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set. This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP. A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)
e.g. dscpmask 0xfc000000 statemask 0x01000000
|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP | unused | flag |unused |
|-----------------------0x01---000000---|
| |
| |
---| Conditional flag
v only restore if set
|-ip diffserv-|
| 6 bits |
|-------------|
The skb mark restore mode (cpmark):
This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.
Parameters related to skb mark restore mode:
mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration. This can be useful where the conntrack
mark is being used for different purposes by different applications. If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)
e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.
|----0x00----conntrack mark----ffffff---|
| Bits 31-24 | |
| DSCP & flag| some value here |
|---------------------------------------|
|
|
v
|------------skb mark-------------------|
| | |
| zeroed | |
|---------------------------------------|
Overall parameters:
zone - conntrack zone
control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a bunch of lines of code or comments that are unnecessary
wrapped into multi-lines. Fix that without violating any code
guidelines.
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
A bunch of typo and formatting fixes.
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Extra check for type is unnecessary in first case.
Extra zeroing is unnecessary, as snprintf guarantees that it will
zero-terminate string.
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
0 is a valid FD, so it's better to initialize it to -1, as is done in
other places. Also, technically, BTF type ID 0 is valid (it's a VOID
type), so it's more reliable to check btf_fd, instead of
btf_key_type_id, to determine if there is any BTF associated with a map.
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
All of libbpf errors are negative, except this one. Fix it.
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Validate there was no error retrieving symbol name corresponding to
a BPF map.
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Rewrite endianness check to use "more canonical" way, using
compiler-defined macros, similar to few other places in libbpf. It also
is more obvious and shorter.
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
pr_warning ultimately may call into user-provided callback function,
which can clobber errno value, so we need to save it before that.
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Ensure that size of a section w/ BPF instruction is exactly a multiple
of BPF instruction size.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This Kselftest update for Linux 5.2-rc3 consists of
- Alexandre Belloni's fixes to rtc regressions introduced in kselftest
Makefile test run output refactoring work from Kees Cook.
- ftrace test checkbashisms fixes from Masami Hiramatsu
-----BEGIN PGP SIGNATURE-----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=zYD6
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- Alexandre Belloni's fixes to rtc regressions introduced in kselftest
Makefile test run output refactoring work from Kees Cook.
- ftrace test checkbashisms fixes from Masami Hiramatsu
* tag 'linux-kselftest-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: rtc: rtctest: specify timeouts
selftests/harness: Allow test to configure timeout
selftests/ftrace: Add checkbashisms meta-testcase
selftests/ftrace: Make a script checkbashisms clean
There are two functions in libbpf that support passing a log_level
parameter for the verifier for loading programs:
bpf_object__load_xattr() and bpf_prog_load_xattr(). Both accept an
attribute object containing the log_level, and apply it to the programs
to load.
It turns out that to effectively load the programs, the latter function
eventually relies on the former. This was not taken into account when
adding support for log_level in bpf_object__load_xattr(), and the
log_level passed to bpf_prog_load_xattr() later gets overwritten with a
zero value, thus disabling verifier logs for the program in all cases:
bpf_prog_load_xattr() // prog->log_level = attr1->log_level;
-> bpf_object__load() // attr2->log_level = 0;
-> bpf_object__load_xattr() // <pass prog and attr2>
-> bpf_object__load_progs() // prog->log_level = attr2->log_level;
Fix this by OR-ing the log_level in bpf_object__load_progs(), instead of
overwriting it.
v2: Fix commit log description (confusion on function names in v1).
Fixes: 60276f9849 ("libbpf: add bpf_object__load_xattr() API function to pass log_level")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add missing header file following compiler warning:
prog_tests/flow_dissector.c: In function ‘tx_tap’:
prog_tests/flow_dissector.c:175:9: warning: implicit declaration of function ‘writev’; did you mean ‘write’? [-Wimplicit-function-declaration]
return writev(fd, iov, ARRAY_SIZE(iov));
^~~~~~
write
Fixes: 0905beec9f ("selftests/bpf: run flow dissector tests in skb-less mode")
Signed-off-by: Alakesh Haloi <alakesh.haloi@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When building the tools/testing/selftest/bpf subdirectory,
(running both a local directory "make" and a
"make -C tools/testing/selftests/bpf") I keep hitting the
following compilation error:
prog_tests/flow_dissector.c: In function ‘create_tap’:
prog_tests/flow_dissector.c:150:38: error: ‘IFF_NAPI’ undeclared (first
use in this function)
.ifr_flags = IFF_TAP | IFF_NO_PI | IFF_NAPI | IFF_NAPI_FRAGS,
^
prog_tests/flow_dissector.c:150:38: note: each undeclared identifier is
reported only once for each function it appears in
prog_tests/flow_dissector.c:150:49: error: ‘IFF_NAPI_FRAGS’ undeclared
Adding include/uapi/linux/if_tun.h to tools/include/uapi/linux
resolves the problem and ensures the compilation of the file
does not depend on having up-to-date kernel headers locally.
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
eBPF ISA specification requires high 32-bit cleared when only low 32-bit
sub-register is written. JIT back-ends must guarantee this semantics when
doing code-gen.
This patch complete unit tests for all of those insns that could be visible
to JIT back-ends and defining sub-registers, if JIT back-ends failed to
guarantee the mentioned semantics, these unit tests will fail.
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It is better to centralize all sub-register zero extension checks into an
independent file.
This patch takes the first step to move existing sub-register zero
extension checks into subreg.c.
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Test the IPv6 flowlabel control and datapath interfaces:
Acquire and release the right to use flowlabels with socket option
IPV6_FLOWLABEL_MGR.
Then configure flowlabels on send and read them on recv with cmsg
IPV6_FLOWINFO. Also verify auto-flowlabel if not explicitly set.
This helped identify the issue fixed in commit 95c169251b ("ipv6:
invert flowlabel sharing check in process and user mode")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the pmtu_vti6_link_change_mtu test, both local and remote addresses
for the vti6 tunnel are assigned to the same address given to the dummy
interface that we use as encapsulating device with a known MTU.
This works as long as the dummy interface is actually selected, via
rt6_lookup(), as encapsulating device. But if the remote address of the
tunnel is a local address too, the loopback interface could also be
selected, and there's nothing wrong with it.
This is what some older -stable kernels do (3.18.z, at least), and
nothing prevents us from subtly changing FIB implementation to revert
back to that behaviour in the future.
Define an IPv6 prefix instead, and use two separate addresses as local
and remote for vti6, so that the encapsulating device can't be a
loopback interface.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: 1fad59ea1c ("selftests: pmtu: Add pmtu_vti6_link_change_mtu test")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a kselftest to cover bpf auto-detachment functionality.
The test creates a cgroup, associates some resources with it,
attaches a couple of bpf programs and deletes the cgroup.
Then it checks that bpf programs are going away in 5 seconds.
Expected output:
$ ./test_cgroup_attach
#override:PASS
#multi:PASS
#autodetach:PASS
test_cgroup_attach:PASS
On a kernel without auto-detaching:
$ ./test_cgroup_attach
#override:PASS
#multi:PASS
#autodetach:FAIL
test_cgroup_attach:FAIL
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Enable all available cgroup v2 controllers when setting up
the environment for the bpf kselftests. It's required to properly test
the bpf prog auto-detach feature. Also it will generally increase
the code coverage.
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Convert test_cgrp2_attach2 example into a proper test_cgroup_attach
kselftest. It's better because we do run kselftest on a constant
basis, so there are better chances to spot a potential regression.
Also make it slightly less verbose to conform kselftests output style.
Output example:
$ ./test_cgroup_attach
#override:PASS
#multi:PASS
test_cgroup_attach:PASS
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
dd53f6102c ("Merge tag 'kvmarm-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD")
59c5c58c5b ("Merge tag 'kvm-ppc-next-5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD")
d7547c55cb ("KVM: Introduce KVM_CAP_MANUAL_DIRTY_LOG_PROTECT2")
6520ca64cd ("KVM: PPC: Book3S HV: XIVE: Add a mapping for the source ESB pages")
39e9af3de5 ("KVM: PPC: Book3S HV: XIVE: Add a TIMA mapping")
e4945b9da5 ("KVM: PPC: Book3S HV: XIVE: Add get/set accessors for the VP XIVE state")
e6714bd167 ("KVM: PPC: Book3S HV: XIVE: Add a control to dirty the XIVE EQ pages")
7b46b6169a ("KVM: PPC: Book3S HV: XIVE: Add a control to sync the sources")
5ca8064748 ("KVM: PPC: Book3S HV: XIVE: Add a global reset control")
13ce3297c5 ("KVM: PPC: Book3S HV: XIVE: Add controls for the EQ configuration")
e8676ce50e ("KVM: PPC: Book3S HV: XIVE: Add a control to configure a source")
4131f83c3d ("KVM: PPC: Book3S HV: XIVE: add a control to initialize a source")
eacc56bb9d ("KVM: PPC: Book3S HV: XIVE: Introduce a new capability KVM_CAP_PPC_IRQ_XIVE")
90c73795af ("KVM: PPC: Book3S HV: Add a new KVM device for the XIVE native exploitation mode")
4f45b90e1c ("KVM: s390: add deflate conversion facilty to cpu model")
a243c16d18 ("KVM: arm64: Add capability to advertise ptrauth for guest")
a22fa321d1 ("KVM: arm64: Add userspace flag to enable pointer authentication")
4bd774e57b ("KVM: arm64/sve: Simplify KVM_REG_ARM64_SVE_VLS array sizing")
8ae6efdde4 ("KVM: arm64/sve: Clean up UAPI register ID definitions")
173aec2d5a ("KVM: s390: add enhanced sort facilty to cpu model")
555f3d03e7 ("KVM: arm64: Add a capability to advertise SVE support")
9033bba4b5 ("KVM: arm64/sve: Add pseudo-register for the guest's vector lengths")
7dd32a0d01 ("KVM: arm/arm64: Add KVM_ARM_VCPU_FINALIZE ioctl")
e1c9c98345 ("KVM: arm64/sve: Add SVE support to register access ioctl interface")
2b953ea348 ("KVM: Allow 2048-bit register access via ioctl interface")
None entails changes in tooling, the closest to that were some new arch
specific ioctls, that are still not handled by the tools/perf/trace/beauty/
library, that needs to create per-arch tables to convert ioctl cmd->string (and
back).
From a quick look the arch specific kvm-stat.c files at:
$ ls -1 tools/perf/arch/*/util/kvm-stat.c
tools/perf/arch/powerpc/util/kvm-stat.c
tools/perf/arch/s390/util/kvm-stat.c
tools/perf/arch/x86/util/kvm-stat.c
$
Are not affected.
This silences these perf building warnings:
Warning: Kernel ABI header at 'tools/include/uapi/linux/kvm.h' differs from latest version at 'include/uapi/linux/kvm.h'
diff -u tools/include/uapi/linux/kvm.h include/uapi/linux/kvm.h
Warning: Kernel ABI header at 'tools/arch/powerpc/include/uapi/asm/kvm.h' differs from latest version at 'arch/powerpc/include/uapi/asm/kvm.h'
diff -u tools/arch/powerpc/include/uapi/asm/kvm.h arch/powerpc/include/uapi/asm/kvm.h
Warning: Kernel ABI header at 'tools/arch/s390/include/uapi/asm/kvm.h' differs from latest version at 'arch/s390/include/uapi/asm/kvm.h'
diff -u tools/arch/s390/include/uapi/asm/kvm.h arch/s390/include/uapi/asm/kvm.h
Warning: Kernel ABI header at 'tools/arch/arm64/include/uapi/asm/kvm.h' differs from latest version at 'arch/arm64/include/uapi/asm/kvm.h'
diff -u tools/arch/arm64/include/uapi/asm/kvm.h arch/arm64/include/uapi/asm/kvm.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Amit Daniel Kachhap <amit.kachhap@arm.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Cédric Le Goater <clg@kaod.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Dave Martin <Dave.Martin@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Peter Xu <peterx@redhat.com>
Link: https://lkml.kernel.org/n/tip-3msmqjenlmb7eygcdnmlqaq1@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Command 'perf record' and 'perf report' on a system without kernel
debuginfo packages uses /proc/kallsyms and /proc/modules to find
addresses for kernel and module symbols. On x86 this works for root and
non-root users.
On s390, when invoked as non-root user, many of the following warnings
are shown and module symbols are missing:
proc/{kallsyms,modules} inconsistency while looking for
"[sha1_s390]" module!
Command 'perf record' creates a list of module start addresses by
parsing the output of /proc/modules and creates a PERF_RECORD_MMAP
record for the kernel and each module. The following function call
sequence is executed:
machine__create_kernel_maps
machine__create_module
modules__parse
machine__create_module --> for each line in /proc/modules
arch__fix_module_text_start
Function arch__fix_module_text_start() is s390 specific. It opens
file /sys/module/<name>/sections/.text to extract the module's .text
section start address. On s390 the module loader prepends a header
before the first section, whereas on x86 the module's text section
address is identical the the module's load address.
However module section files are root readable only. For non-root the
read operation fails and machine__create_module() returns an error.
Command perf record does not generate any PERF_RECORD_MMAP record
for loaded modules. Later command perf report complains about missing
module maps.
To fix this function arch__fix_module_text_start() always returns
success. For root users there is no change, for non-root users
the module's load address is used as module's text start address
(the prepended header then counts as part of the text section).
This enable non-root users to use module symbols and avoid the
warning when perf report is executed.
Output before:
[tmricht@m83lp54 perf]$ ./perf report -D | fgrep MMAP
0 0x168 [0x50]: PERF_RECORD_MMAP ... x [kernel.kallsyms]_text
Output after:
[tmricht@m83lp54 perf]$ ./perf report -D | fgrep MMAP
0 0x168 [0x50]: PERF_RECORD_MMAP ... x [kernel.kallsyms]_text
0 0x1b8 [0x98]: PERF_RECORD_MMAP ... x /lib/modules/.../autofs4.ko.xz
0 0x250 [0xa8]: PERF_RECORD_MMAP ... x /lib/modules/.../sha_common.ko.xz
0 0x2f8 [0x98]: PERF_RECORD_MMAP ... x /lib/modules/.../des_generic.ko.xz
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Link: http://lkml.kernel.org/r/20190522144601.50763-4-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We mark the end of kernel based on the first module, but that could
cover some bpf program maps. Reading _etext symbol if it's present to
get precise kernel map end.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Link: http://lkml.kernel.org/r/20190508132010.14512-6-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
No need to search for aliases for the symbol that marks the end of the
kernel text segment, the following patch will make such symbols not to
be found when searching in the kallsyms maps causing this test to fail.
So as a prep patch to avoid breaking bisection, ignore such symbols.
Tested-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Link: https://lkml.kernel.org/n/tip-qfwuih8cvmk9doh7k5k244eq@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In case it's recorded in a different arch.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com> <hbathini@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Krister Johansen <kjlx@templeofstupid.com>
Fixes: f3b3614a28 ("perf tools: Add PERF_RECORD_NAMESPACES to include namespaces related info")
Link: http://lkml.kernel.org/r/20190522053250.207156-3-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It seems that the current code lacks holding the namespace lock in
thread__namespaces(). Otherwise it can see inconsistent results.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Krister Johansen <kjlx@templeofstupid.com>
Link: http://lkml.kernel.org/r/20190522053250.207156-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick up the changes in these csets:
060cebb20c ("drm: introduce a capability flag for syncobj timeline support")
50d1ebef79 ("drm/syncobj: add timeline signal ioctl for syncobj v5")
ea569910cb ("drm/syncobj: add transition iotcls between binary and timeline v2")
27b575a9aa ("drm/syncobj: add timeline payload query ioctl v6")
01d6c35783 ("drm/syncobj: add support for timeline point wait v8")
783195ec1c ("drm/syncobj: disable the timeline UAPI for now v2")
48197bc564 ("drm: add syncobj timeline support v9")
Which automagically results in the following new ioctls being recognized
by the 'perf trace' ioctl cmd arg beautifier:
$ tools/perf/trace/beauty/drm_ioctl.sh > /tmp/before
$ cp include/uapi/drm/drm.h tools/include/uapi/drm/drm.h
$ tools/perf/trace/beauty/drm_ioctl.sh > /tmp/after
$ diff -u /tmp/before /tmp/after
--- /tmp/before 2019-05-22 10:25:31.443151182 -0300
+++ /tmp/after 2019-05-22 10:25:46.449354819 -0300
@@ -103,6 +103,10 @@
[0xC7] = "MODE_LIST_LESSEES",
[0xC8] = "MODE_GET_LEASE",
[0xC9] = "MODE_REVOKE_LEASE",
+ [0xCA] = "SYNCOBJ_TIMELINE_WAIT",
+ [0xCB] = "SYNCOBJ_QUERY",
+ [0xCC] = "SYNCOBJ_TRANSFER",
+ [0xCD] = "SYNCOBJ_TIMELINE_SIGNAL",
[DRM_COMMAND_BASE + 0x00] = "I915_INIT",
[DRM_COMMAND_BASE + 0x01] = "I915_FLUSH",
[DRM_COMMAND_BASE + 0x02] = "I915_FLIP",
$
I.e. the strace like raw_tracepoint:sys_enter handler in 'perf trace'
will get the cmd integer value and map it to the string.
At some point it should be possible to translate from string to integer
and use to filter using expressions such as:
# perf trace -e ioctl/cmd==DRM_IOCTL_SYNCOBJ*/
Or some more suitable syntax to express that only these ioctls when
acting on DRM fds should be shown.
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/n/tip-jrc9ogw33w4zgqc3pu7o1l3g@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick up the changes from:
d1172ab3d4 ("drm/i915: Introduce struct class_instance for engines across the uAPI")
96fd2c6633 ("drm/i915: Drop new chunks of context creation ABI (for now)")
ea593dbba4 ("drm/i915: Allow contexts to share a single timeline across all engines")
b917154172 ("drm/i915: Extend CONTEXT_CREATE to set parameters upon construction")
e0695db729 ("drm/i915: Create/destroy VM (ppGTT) for use with contexts")
9d1305ef80 ("drm/i915: Introduce the i915_user_extension_method")
c8b502422b ("drm/i915: Remove last traces of exec-id (GEM_BUSY)")
d90c06d570 ("drm/i915: Fix I915_EXEC_RING_MASK")
e886196469 ("drm/i915: Use HW semaphores for inter-engine synchronisation on gen8+")
be03564bd7 ("drm/i915: Include reminders about leaving no holes in uAPI enums")
ba4fda620a ("drm/i915: Optionally disable automatic recovery after a GPU reset")
We still don't take into account the _IOC_SIZE() to differentiate ioctl cmds,
so more work is needed to support the extension mechanism that is being used
here so that we can differentiate DRM_IOCTL_I915_GEM_CONTEXT_CREATE from the
newly introduced DRM_IOCTL_I915_GEM_CONTEXT_CREATE_EXT cmd.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/drm/i915_drm.h' differs from latest version at 'include/uapi/drm/i915_drm.h'
diff -u tools/include/uapi/drm/i915_drm.h include/uapi/drm/i915_drm.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://lkml.kernel.org/n/tip-csn0vanmc7pevyka5qcg0xyw@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick up the changes in:
c553ea4fdf ("fs/sync.c: sync_file_range(2) may use WB_SYNC_ALL writeback")
That should be used to beautify the 'sync_file_range' syscall 'flags'
arg.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/fs.h' differs from latest version at 'include/uapi/linux/fs.h'
diff -u tools/include/uapi/linux/fs.h include/uapi/linux/fs.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/n/tip-at3uoqcvmqdkwaysmvbj1wpv@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick up the change in:
b3e5838252 ("clone: add CLONE_PIDFD")
This requires changes in the 'perf trace' beautification routines for
the 'clone' syscall args, which is done in a followup patch.
This silences the following perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/sched.h' differs from latest version at 'include/uapi/linux/sched.h'
diff -u tools/include/uapi/linux/sched.h include/uapi/linux/sched.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Christian Brauner <christian@brauner.io>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lkml.kernel.org/n/tip-lenja6gmy26dkt0ybk747qgq@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick up the changes in:
ed5194c273 ("x86/speculation/mds: Add basic bug infrastructure for MDS")
e261f209c3 ("x86/speculation/mds: Add BUG_MSBDS_ONLY")
That don't affect anything in tools/.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/arch/x86/include/asm/cpufeatures.h' differs from latest version at 'arch/x86/include/asm/cpufeatures.h'
diff -u tools/arch/x86/include/asm/cpufeatures.h arch/x86/include/asm/cpufeatures.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/n/tip-jp1afecx3ql1jkuirpgkqfad@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Copy the headers changed by these csets:
d8076bdb56 ("uapi: Wire up the mount API syscalls on non-x86 arches [ver #2]")
9c8ad7a2ff ("uapi, x86: Fix the syscall numbering of the mount API syscalls [ver #2]")
cf3cba4a42 ("vfs: syscall: Add fspick() to select a superblock for reconfiguration")
93766fbd26 ("vfs: syscall: Add fsmount() to create a mount for a superblock")
ecdab150fd ("vfs: syscall: Add fsconfig() for configuring and managing a context")
24dcb3d90a ("vfs: syscall: Add fsopen() to prepare for superblock creation")
2db154b3ea ("vfs: syscall: Add move_mount(2) to move mounts around")
a07b200047 ("vfs: syscall: Add open_tree(2) to reference or clone a mount")
We need to create tables for all the flags argument in the new syscalls,
in followup patches.
This silences these perf build warnings:
Warning: Kernel ABI header at 'tools/include/uapi/linux/mount.h' differs from latest version at 'include/uapi/linux/mount.h'
diff -u tools/include/uapi/linux/mount.h include/uapi/linux/mount.h
Warning: Kernel ABI header at 'tools/perf/arch/x86/entry/syscalls/syscall_64.tbl' differs from latest version at 'arch/x86/entry/syscalls/syscall_64.tbl'
diff -u tools/perf/arch/x86/entry/syscalls/syscall_64.tbl arch/x86/entry/syscalls/syscall_64.tbl
Warning: Kernel ABI header at 'tools/include/uapi/asm-generic/unistd.h' differs from latest version at 'include/uapi/asm-generic/unistd.h'
diff -u tools/include/uapi/asm-generic/unistd.h include/uapi/asm-generic/unistd.h
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Luis Cláudio Gonçalves <lclaudio@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-knpqr1u2ffvz6641056z2mwu@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When a host system has kernel headers that are newer than a compiling
kernel, mksyscalltbl fails with errors such as:
<stdin>: In function 'main':
<stdin>:271:44: error: '__NR_kexec_file_load' undeclared (first use in this function)
<stdin>:271:44: note: each undeclared identifier is reported only once for each function it appears in
<stdin>:272:46: error: '__NR_pidfd_send_signal' undeclared (first use in this function)
<stdin>:273:43: error: '__NR_io_uring_setup' undeclared (first use in this function)
<stdin>:274:43: error: '__NR_io_uring_enter' undeclared (first use in this function)
<stdin>:275:46: error: '__NR_io_uring_register' undeclared (first use in this function)
tools/perf/arch/arm64/entry/syscalls//mksyscalltbl: line 48: /tmp/create-table-xvUQdD: Permission denied
mksyscalltbl is compiled with default host includes, but run with
compiling kernel tree includes, causing some syscall numbers to being
undeclared.
Committer testing:
Before this patch, in my cross build environment, no build problems, but
these new syscalls were not in the syscalls.c generated from the
unistd.h file, which is a bug, this patch fixes it:
perfbuilder@6e20056ed532:/git/perf$ tail /tmp/build/perf/arch/arm64/include/generated/asm/syscalls.c
[292] = "io_pgetevents",
[293] = "rseq",
[294] = "kexec_file_load",
[424] = "pidfd_send_signal",
[425] = "io_uring_setup",
[426] = "io_uring_enter",
[427] = "io_uring_register",
[428] = "syscalls",
};
perfbuilder@6e20056ed532:/git/perf$ strings /tmp/build/perf/perf | egrep '^(io_uring_|pidfd_|kexec_file)'
kexec_file_load
pidfd_send_signal
io_uring_setup
io_uring_enter
io_uring_register
perfbuilder@6e20056ed532:/git/perf$
$
Well, there is that last "syscalls" thing, but that looks like some
other bug.
Signed-off-by: Vitaly Chikunov <vt@altlinux.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Michael Petlan <mpetlan@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kim Phillips <kim.phillips@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20190521030203.1447-1-vt@altlinux.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This strncat() is safe because the buffer was allocated with zalloc(),
however gcc doesn't know that. Since the string always has 4 non-null
bytes, just use memcpy() here.
CC /home/shawn/linux/tools/perf/util/data-convert-bt.o
In file included from /usr/include/string.h:494,
from /home/shawn/linux/tools/lib/traceevent/event-parse.h:27,
from util/data-convert-bt.c:22:
In function ‘strncat’,
inlined from ‘string_set_value’ at util/data-convert-bt.c:274:4:
/usr/include/powerpc64le-linux-gnu/bits/string_fortified.h:136:10: error: ‘__builtin_strncat’ output may be truncated copying 4 bytes from a string of length 4 [-Werror=stringop-truncation]
136 | return __builtin___strncat_chk (__dest, __src, __len, __bos (__dest));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shawn Landden <shawn@git.icu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
LPU-Reference: 20190518183238.10954-1-shawn@git.icu
Link: https://lkml.kernel.org/n/tip-289f1jice17ta7tr3tstm9jm@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Right now test_tunnel.sh always exits with success even if some
of the subtests fail. Since the output is very verbose, it's
hard to spot the issues with subtests. Let's fail the script
if any subtest fails.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The "-d" option is used to require all logs available for bpftool. So
far it meant telling libbpf to print even debug-level information. But
there is another source of info that can be made more verbose: when we
attemt to load programs with bpftool, we can pass a log_level parameter
to the verifier in order to control the amount of information that is
printed to the console.
Reuse the "-d" option to print all information the verifier can tell. At
this time, this means logs related to BPF_LOG_LEVEL1, BPF_LOG_LEVEL2 and
BPF_LOG_STATS. As mentioned in the discussion on the first version of
this set, these macros are internal to the kernel
(include/linux/bpf_verifier.h) and are not meant to be part of the
stable user API, therefore we simply use the related constants to print
whatever we can at this time, without trying to tell users what is
log_level1 or what is statistics.
Verifier logs are only used when loading programs for now (In the
future: for loading BTF objects with bpftool? Although libbpf does not
currently offer to print verifier info at debug level if no error
occurred when loading BTF objects), so bpftool.rst and bpftool-prog.rst
are the only man pages to get the update.
v3:
- Add details on log level and BTF loading at the end of commit log.
v2:
- Remove the possibility to select the log levels to use (v1 offered a
combination of "log_level1", "log_level2" and "stats").
- The macros from kernel header bpf_verifier.h are not used (and
therefore not moved to UAPI header).
- In v1 this was a distinct option, but is now merged in the only "-d"
switch to activate libbpf and verifier debug-level logs all at the
same time.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
libbpf was recently made aware of the log_level attribute for programs,
used to specify the level of information expected to be dumped by the
verifier. Function bpf_prog_load_xattr() got support for this log_level
parameter.
But some applications using libbpf rely on another function to load
programs, bpf_object__load(), which does accept any parameter for log
level. Create an API function based on bpf_object__load(), but accepting
an "attr" object as a parameter. Then add a log_level field to that
object, so that applications calling the new bpf_object__load_xattr()
can pick the desired log level.
v3:
- Rewrite commit log.
v2:
- We are in a new cycle, bump libbpf extraversion number.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
libbpf has three levels of priority for output messages: warn, info,
debug. By default, debug output is not printed to the console.
Add a new "--debug" (short name: "-d") option to bpftool to print libbpf
logs for all three levels.
Internally, we simply use the function provided by libbpf to replace the
default printing function by one that prints logs regardless of their
level.
v2:
- Remove the possibility to select the log-levels to use (v1 offered a
combination of "warn", "info" and "debug").
- Rename option and offer a short name: -d|--debug.
- Add option description to all bpftool manual pages (instead of
bpftool-prog.rst only), as all commands use libbpf.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Fix below warning reported by coccicheck:
/tools/lib/bpf/libbpf.c:3461:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Use fgets() as the while loop condition.
Signed-off-by: Chang-Hsien Tsai <luke.tw@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Auto-complete BTF IDs for `btf dump id` sub-command. List of possible BTF
IDs is scavenged from loaded BPF programs that have associated BTFs, as
there is currently no API in libbpf to fetch list of all BTFs in the
system.
Suggested-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The condition to test is unlikely() to be true. Add the hint.
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Virtualization@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I was really surprised that the IPv6 mtu exception followed by redirect
test was passing as nothing about the code suggests it should. The problem
is actually with the logic in the test script.
Fix the test cases as follows:
1. add debug function to dump the initial and redirect gateway addresses
for ipv6. This is shown only in verbose mode. It helps verify the
output of 'route get'.
2. fix the check_exception logic for the reset case to make sure that
for IPv4 neither mtu nor redirect appears in the 'route get' output.
For IPv6, make sure mtu is not present and the gateway is the initial
R1 lladdr.
3. fix the reset logic by using a function to delete the routes added by
initial_route_*. This format works better for the nexthop version of
the tests.
While improving the test cases, go ahead and ensure that forwarding is
disabled since IPv6 redirect requires it.
Also, runs with kernel debugging enabled sometimes show a failure with
one of the ipv4 tests, so spread the pings over longer time interval.
The end result is that 2 tests now show failures:
TEST: IPv6: mtu exception plus redirect [FAIL]
and the VRF version.
This is a bug in the IPv6 logic that will need to be fixed
separately. Redirect followed by MTU works because __ip6_rt_update_pmtu
hits the 'if (!rt6_cache_allowed_for_pmtu(rt6))' path and updates the
mtu on the exception rt6_info.
MTU followed by redirect does not have this logic. rt6_do_redirect
creates a new exception and then rt6_insert_exception removes the old
one which has the MTU exception.
Fixes: ec81053528 ("selftests: Add redirect tests")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test which sends 15 bytes of data, and then tries
to read 10 byes twice. Previously the second read would
sleep indifinitely, since the record was already decrypted
and there is only 5 bytes left, not full 10.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set SO_RCVLOWAT and test it gets respected when gathering
data from multiple records.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
merge window, but should not wait four months before they appear in
a release. I also travelled a bit more than usual in the first part
of May, which didn't help with picking up patches and reports promptly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc6RkmAAoJEL/70l94x66DhEAH/ijCkibV9vOUu8n/lSxMjAzi
I/Y1VEaVRFuQ6u0QSjWBBg22tVsWuWiVbonJ63w3JMRwi5Q5zW9REE7EaKRAa/eC
FiFE7vTesYh6sGVwdMCwoinjMDyCp7hybvtBc608+MWhVmrdzTYtPm5N85wxIDtW
xH5Kr2mVeLC43X3vfegolmXZ1obAbZEToJvOgJrYFhnzsmVYYl182kfGtrppBoO0
XXDPuDRGpTrm6A2oADMdOv+mT9p51pHsedmHQaDGXwAGEC/BkOGKdIdBfwppEwy7
QP2NGqwkHIyghV1aCPacT6O6G6xL0i2rfvlJ7+e6o7deU4uMXAqIdQ2DbIcHy3g=
=5IW2
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"The usual smattering of fixes and tunings that came in too late for
the merge window, but should not wait four months before they appear
in a release.
I also travelled a bit more than usual in the first part of May, which
didn't help with picking up patches and reports promptly"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (33 commits)
KVM: x86: fix return value for reserved EFER
tools/kvm_stat: fix fields filter for child events
KVM: selftests: Wrap vcpu_nested_state_get/set functions with x86 guard
kvm: selftests: aarch64: compile with warnings on
kvm: selftests: aarch64: fix default vm mode
kvm: selftests: aarch64: dirty_log_test: fix unaligned memslot size
KVM: s390: fix memory slot handling for KVM_SET_USER_MEMORY_REGION
KVM: x86/pmu: do not mask the value that is written to fixed PMUs
KVM: x86/pmu: mask the result of rdpmc according to the width of the counters
x86/kvm/pmu: Set AMD's virt PMU version to 1
KVM: x86: do not spam dmesg with VMCS/VMCB dumps
kvm: Check irqchip mode before assign irqfd
kvm: svm/avic: fix off-by-one in checking host APIC ID
KVM: selftests: do not blindly clobber registers in guest asm
KVM: selftests: Remove duplicated TEST_ASSERT in hyperv_cpuid.c
KVM: LAPIC: Expose per-vCPU timer_advance_ns to userspace
KVM: LAPIC: Fix lapic_timer_advance_ns parameter overflow
kvm: vmx: Fix -Wmissing-prototypes warnings
KVM: nVMX: Fix using __this_cpu_read() in preemptible context
kvm: fix compilation on s390
...
The previous libbpf patch allows user to specify "prog_flags" to bpf
program load APIs. To enable high 32-bit randomization for a test, we need
to set BPF_F_TEST_RND_HI32 in "prog_flags".
To enable such randomization for all tests, we need to make sure all places
are passing BPF_F_TEST_RND_HI32. Changing them one by one is not
convenient, also, it would be better if a test could be switched to
"normal" running mode without code change.
Given the program load APIs used across bpf selftests are mostly:
bpf_prog_load: load from file
bpf_load_program: load from raw insns
A test_stub.c is implemented for bpf seltests, it offers two functions for
testing purpose:
bpf_prog_test_load
bpf_test_load_program
The are the same as "bpf_prog_load" and "bpf_load_program", except they
also set BPF_F_TEST_RND_HI32. Given *_xattr functions are the APIs to
customize any "prog_flags", it makes little sense to put these two
functions into libbpf.
Then, the following CFLAGS are passed to compilations for host programs:
-Dbpf_prog_load=bpf_prog_test_load
-Dbpf_load_program=bpf_test_load_program
They migrate the used load APIs to the test version, hence enable high
32-bit randomization for these tests without changing source code.
Besides all these, there are several testcases are using
"bpf_prog_load_attr" directly, their call sites are updated to pass
BPF_F_TEST_RND_HI32.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
- bpf_fill_ld_abs_vlan_push_pop:
Prevent zext happens inside PUSH_CNT loop. This could happen because
of BPF_LD_ABS (32-bit def) + BPF_JMP (64-bit use), or BPF_LD_ABS +
EXIT (64-bit use of R0). So, change BPF_JMP to BPF_JMP32 and redefine
R0 at exit path to cut off the data-flow from inside the loop.
- bpf_fill_jump_around_ld_abs:
Jump range is limited to 16 bit. every ld_abs is replaced by 6 insns,
but on arches like arm, ppc etc, there will be one BPF_ZEXT inserted
to extend the error value of the inlined ld_abs sequence which then
contains 7 insns. so, set the dividend to 7 so the testcase could
work on all arches.
- bpf_fill_scale1/bpf_fill_scale2:
Both contains ~1M BPF_ALU32_IMM which will trigger ~1M insn patcher
call because of hi32 randomization later when BPF_F_TEST_RND_HI32 is
set for bpf selftests. Insn patcher is not efficient that 1M call to
it will hang computer. So , change to BPF_ALU64_IMM to avoid hi32
randomization.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
libbpf doesn't allow passing "prog_flags" during bpf program load in a
couple of load related APIs, "bpf_load_program_xattr", "load_program" and
"bpf_prog_load_xattr".
It makes sense to allow passing "prog_flags" which is useful for
customizing program loading.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Sync new bpf prog load flag "BPF_F_TEST_RND_HI32" to tools/.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
-----BEGIN PGP SIGNATURE-----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=lGyw
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190524' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Keith, with fixes from a few folks.
- bio and sbitmap before atomic barrier fixes (Andrea)
- Hang fix for blk-mq freeze and unfreeze (Bob)
- Single segment count regression fix (Christoph)
- AoE now has a new maintainer
- tools/io_uring/ Makefile fix, and sync with liburing (me)
* tag 'for-linus-20190524' of git://git.kernel.dk/linux-block: (23 commits)
tools/io_uring: sync with liburing
tools/io_uring: fix Makefile for pthread library link
blk-mq: fix hang caused by freeze/unfreeze sequence
block: remove the bi_seg_{front,back}_size fields in struct bio
block: remove the segment size check in bio_will_gap
block: force an unlimited segment size on queues with a virt boundary
block: don't decrement nr_phys_segments for physically contigous segments
sbitmap: fix improper use of smp_mb__before_atomic()
bio: fix improper use of smp_mb__before_atomic()
aoe: list new maintainer for aoe driver
nvme-pci: use blk-mq mapping for unmanaged irqs
nvme: update MAINTAINERS
nvme: copy MTFA field from identify controller
nvme: fix memory leak for power latency tolerance
nvme: release namespace SRCU protection before performing controller ioctls
nvme: merge nvme_ns_ioctl into nvme_ioctl
nvme: remove the ifdef around nvme_nvm_ioctl
nvme: fix srcu locking on error return in nvme_get_ns_from_disk
nvme: Fix known effects
nvme-pci: Sync queues on reset
...
This Kselftest fixes update for Linux 5.2-rc2 consists of:
- 2 fixes to regressions introduced in kselftest Makefile test run output
refactoring work from Kees Cook.
- Adding Atom support to syscall_arg_fault test from Tong Bo.
-----BEGIN PGP SIGNATURE-----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=BYfS
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- Two fixes to regressions introduced in kselftest Makefile test run
output refactoring work (Kees Cook)
- Adding Atom support to syscall_arg_fault test (Tong Bo)
* tag 'linux-kselftest-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/timers: Add missing fflush(stdout) calls
selftests: Remove forced unbuffering for test running
selftests/x86: Support Atom for syscall_arg_fault test
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later". Only the "obvious" versions of these matches are
included here, a number of "non-obvious" variants of text have been
found but those have been postponed for later review and analysis.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOgmlw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk4rACfRqxGOGVLR/t6E9dDzOZRAdEz/mYAoJLZmziY
0YlSSSPtP5HI6JDh65Ng
=HXQb
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pule more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later".
Only the "obvious" versions of these matches are included here, a
number of "non-obvious" variants of text have been found but those
have been postponed for later review and analysis.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (85 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 125
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 123
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 122
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 121
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 120
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 119
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 118
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 116
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 114
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 113
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 112
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 111
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 110
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 106
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 105
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 104
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 103
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 102
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 101
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 98
...
The bpf uapi header include/uapi/linux/bpf.h is sync'ed
to tools/include/uapi/linux/bpf.h.
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Utilize new libbpf's btf_dump API to emit BTF as a C definitions.
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add new test_btf_dump set of tests, validating BTF-to-C conversion
correctness. Tests rely on clang to generate BTF from provided C test
cases.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
BTF contains enough type information to allow generating valid
compilable C header w/ correct layout of structs/unions and all the
typedef/enum definitions. This patch adds a new "object" - btf_dump to
facilitate dumping BTF as valid C. btf_dump__dump_type() is the main API
which takes care of dumping out (through user-provided printf-like
callback function) C definitions for given type ID and it's required
dependencies. This allows for not just dumping out entirety of BTF types,
but also selective filtering based on user-provided criterias w/ minimal
set of dependent types.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
There is a need for fast point lookups inside libbpf for multiple use
cases (e.g., name resolution for BTF-to-C conversion, by-name lookups in
BTF for upcoming BPF CO-RE relocation support, etc). This patch
implements simple resizable non-thread safe hashmap using single linked
list chains.
Four different insert strategies are supported:
- HASHMAP_ADD - only add key/value if key doesn't exist yet;
- HASHMAP_SET - add key/value pair if key doesn't exist yet; otherwise,
update value;
- HASHMAP_UPDATE - update value, if key already exists; otherwise, do
nothing and return -ENOENT;
- HASHMAP_APPEND - always add key/value pair, even if key already exists.
This turns hashmap into a multimap by allowing multiple values to be
associated with the same key. Most useful read API for such hashmap is
hashmap__for_each_key_entry() iteration. If hashmap__find() is still
used, it will return last inserted key/value entry (first in a bucket
chain).
For HASHMAP_SET and HASHMAP_UPDATE, old key/value pair is returned, so
that calling code can handle proper memory management, if necessary.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Switch test_btf.c to rely on btf__parse_elf to check presence of BTF and
BTF.ext data, instead of implementing its own ELF parsing.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Loading BTF and BTF.ext from ELF file is a common need. Instead of
requiring every user to re-implement it, let's provide this API from
libbpf itself. It's mostly copy/paste from `bpftool btf dump`
implementation, which will be switched to libbpf's version in next
patch. btf__parse_elf allows to load BTF and optionally BTF.ext.
This is also useful for tests that need to load/work with BTF, loaded
from test ELF files.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
libbpf_internal.h expects a bunch of stuff defined in libbpf.h to be
defined. This patch makes sure that libbpf.h is always included.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
bpf_printk is a macro which is commonly used to print out debug messages
in BPF programs and it was copied in many selftests and samples. Since
all of them include bpf_helpers.h, this change moves the macro there.
Signed-off-by: Michal Rostecki <mrostecki@opensuse.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The SO_TXTIME API enables packet tranmission with delayed delivery.
This is currently supported by the ETF and FQ packet schedulers.
Evaluate the interface with both schedulers. Install the scheduler
and send a variety of packets streams: without delay, with one
delayed packet, with multiple ordered delays and with reordering.
Verify that packets are released by the scheduler in expected order.
The ETF qdisc requires a timestamp in the future on every packet. It
needs a delay on the qdisc else the packet is dropped on dequeue for
having a delivery time in the past. The test value is experimentally
derived. ETF requires clock_id CLOCK_TAI. It checks this base and
drops for non-conformance.
The FQ qdisc expects clock_id CLOCK_MONOTONIC, the base used by TCP
as of commit fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC").
Within a flow there is an expecation of ordered delivery, as shown by
delivery times of test 4. The FQ qdisc does not require all packets to
have timestamps and does not drop for non-conformance.
The large (msec) delays are chosen to avoid flakiness.
Output:
SO_TXTIME ipv6 clock monotonic
payload:a delay:28 expected:0 (us)
SO_TXTIME ipv4 clock monotonic
payload:a delay:38 expected:0 (us)
SO_TXTIME ipv6 clock monotonic
payload:a delay:40 expected:0 (us)
SO_TXTIME ipv4 clock monotonic
payload:a delay:33 expected:0 (us)
SO_TXTIME ipv6 clock monotonic
payload:a delay:10120 expected:10000 (us)
SO_TXTIME ipv4 clock monotonic
payload:a delay:10102 expected:10000 (us)
[.. etc ..]
OK. All tests passed
Changes v1->v2: update commit message output
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test for ICMP redirects and exception processing. Test is setup
for later addition of tests using nexthop objects for routing.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
uie_read is a commonly failing test that will block forever on buggy rtc
drivers. Shorten its timeout so it fails earlier. Also increase the timeout
for the two alarm test on a minute boundary.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Commit a745f7af3c ("selftests/harness: Add 30 second timeout per test")
adds an hardcoded 30s timeout to all tests. Unfortunately, rtctest has two
tests taking up to 60s. Allow for individual tests to define their own
timeout.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add a meta-testcase which tests ftracetest itself with
checkbasisms. This helps us to keep our test script
bashisms clean.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Make kprobe_ftrace.tc checkbashisms clean. Since
"grep function available_tracers" causes an error
on checkbashisms, fix it by explicitly escaping
with double-quotations.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The fields filter would not work with child fields, as the respective
parents would not be included. No parents displayed == no childs displayed.
To reproduce, run on s390 (would work on other platforms, too, but would
require a different filter name):
- Run 'kvm_stat -d'
- Press 'f'
- Enter 'instruct'
Notice that events like instruction_diag_44 or instruction_diag_500 are not
displayed - the output remains empty.
With this patch, we will filter by matching events and their parents.
However, consider the following example where we filter by
instruction_diag_44:
kvm statistics - summary
regex filter: instruction_diag_44
Event Total %Total CurAvg/s
exit_instruction 276 100.0 12
instruction_diag_44 256 92.8 11
Total 276 12
Note that the parent ('exit_instruction') displays the total events, but
the childs listed do not match its total (256 instead of 276). This is
intended (since we're filtering all but one child), but might be confusing
on first sight.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
struct kvm_nested_state is only available on x86 so far. To be able
to compile the code on other architectures as well, we need to wrap
the related code with #ifdefs.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
aarch64 fixups needed to compile with warnings as errors.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VM_MODE_P52V48_4K is not a valid mode for AArch64. Replace its
use in vm_create_default() with a mode that works and represents
a good AArch64 default. (We didn't ever see a problem with this
because we don't have any unit tests using vm_create_default(),
but it's good to get it fixed in advance.)
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The memory slot size must be aligned to the host's page size. When
testing a guest with a 4k page size on a host with a 64k page size,
then 3 guest pages are not host page size aligned. Since we just need
a nearly arbitrary number of extra pages to ensure the memslot is not
aligned to a 64 host-page boundary for this test, then we can use
16, as that's 64k aligned, but not 64 * 64k aligned.
Fixes: 76d58e0f07 ("KVM: fix KVM_CLEAR_DIRTY_LOG for memory slots of unaligned size", 2019-04-17)
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The guest_code of sync_regs_test is assuming that the compiler will not
touch %r11 outside the asm that increments it, which is a bit brittle.
Instead, we can increment a variable and use a dummy asm to ensure the
increment is not optimized away. However, we also need to use a
callee-save register or the compiler will insert a save/restore around
the vmexit, breaking the whole idea behind the test.
(Yes, "if it ain't broken...", but I would like the test to be clean
before it is copied into the upcoming s390 selftests).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The check for entry->index == 0 is done twice. One time should
be sufficient.
Suggested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
So far the KVM selftests are compiled without any compiler warnings
enabled. That's quite bad, since we miss a lot of possible bugs this
way. Let's enable at least "-Wall" and some other useful warning flags
now, and fix at least the trivial problems in the code (like unused
variables).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The code is trying to check that all the padding is zeroed out and it
does this:
entry->padding[0] == entry->padding[1] == entry->padding[2] == 0
Assume everything is zeroed correctly, then the first comparison is
true, the next comparison is false and false is equal to zero so the
overall condition is true. This bug doesn't affect run time very
badly, but the code should instead just check that all three paddings
are zero individually.
Also the error message was copy and pasted from an earlier error and it
wasn't correct.
Fixes: 7edcb73433 ("KVM: selftests: Add hyperv_cpuid test")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 or
later as published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 6 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520075211.856638608@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public licence as published by
the free software foundation either version 2 of the licence or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 114 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170857.552531963@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) Fix crash when dumping rules after conversion to RCU,
from Florian Westphal.
2) Fix incorrect hook reinjection from nf_queue in case NF_REPEAT,
from Jagdish Motwani.
3) Fix check for route existence in fib extension, from Phil Sutter.
4) Fix use after free in ip_vs_in() hook, from YueHaibing.
5) Check for veth existence from netfilter selftests,
from Jeffrin Jose T.
6) Checksum corruption in UDP NAT helpers due to typo,
from Florian Westphal.
7) Pass up packets to classic forwarding path regardless of
IPv4 DF bit, patch for the flowtable infrastructure from Florian.
8) Set liberal TCP tracking for flows that are placed in the
flowtable, in case they need to go back to classic forwarding path,
also from Florian.
9) Don't add flow with sequence adjustment to flowtable, from Florian.
10) Skip IPv4 options from IPv6 datapath in flowtable, from Florian.
11) Add selftest for the flowtable infrastructure, from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Various fixes and changes have been applied to liburing since we
copied some select bits to the kernel testing/examples part, sync
up with liburing to get those changes.
Most notable is the change that split the CQE reading into the peek
and seen event, instead of being just a single function. Also fixes
an unsigned wrap issue in io_uring_submit(), leak of 'fd' in setup
if we fail, and various other little issues.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently fails with:
io_uring-bench.o: In function `main':
/home/axboe/git/linux-block/tools/io_uring/io_uring-bench.c:560: undefined reference to `pthread_create'
/home/axboe/git/linux-block/tools/io_uring/io_uring-bench.c:588: undefined reference to `pthread_join'
collect2: error: ld returned 1 exit status
Makefile:11: recipe for target 'io_uring-bench' failed
make: *** [io_uring-bench] Error 1
Move -lpthread to the end.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a snippet of pyperf bpf program used to collect python stack traces
as a scale test for the verifier.
At 189 loop iterations llvm 9.0 starts ignoring '#pragma unroll'
and generates partially unrolled loop instead.
Hence use 50, 100, and 180 loop iterations to stress test.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Adjust scale tests to check for new jmp sequence limit.
BPF_JGT had to be changed to BPF_JEQ because the verifier was
too smart. It tracked the known safe range of R0 values
and pruned the search earlier before hitting exact 8192 limit.
bpf_semi_rand_get() was too (un)?lucky.
k = 0; was missing in bpf_fill_scale2.
It was testing a bit shorter sequence of jumps than intended.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add three tests to test_verifier/basic_instr that make sure that the
high 32-bits of the destination register is cleared after an ALU32
and/or/xor.
Signed-off-by: Björn Töpel <bjorn.topel@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It's easy to have a mismatch of "intended to be public" vs really
exposed API functions. While Makefile does check for this mismatch, if
it actually occurs it's not trivial to determine which functions are
accidentally exposed. This patch dumps out a diff showing what's not
supposed to be exposed facilitating easier fixing.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The point of the pause-on-fail argument is to leave the setup as is after
a test fails to allow a user to debug why it failed. Move the cleanup
after posting the result to the user to make it so.
Random names for the namespaces are not user friendly when trying to
debug a failure. Make them simpler and more direct for the tests. Run
cleanup at the beginning to ensure they are cleaned up if they already
exist.
Remove cleanup_done. There is no harm in doing cleanup twice; just
ignore any errors related to not existing - which is already done.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add VERBOSE argument to fib-onlink-tests.sh and make output quiet by
default. Add getopt parsing of inputs and support for -v (verbose) and
-p (pause on fail).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
Exercises 3 cases:
1. no pmtu discovery (need to frag)
2. no PMTUd + NAT (don't flag packets as invalid from conntrack)
3. PMTU + NAT (need to send icmp error)
The first two cases make sure we handle fragments correctly, i.e.
pass them to classic forwarding path.
Third case checks we offload everything (in the test case,
PMTUd will kick in so all packets should be within link mtu).
Nftables rules will filter packets that are supposed to be
handled by the fast-path.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
DEV_ADDR is defined but not used. Use it in address setting.
Do the same with IPv6 for consistency.
Reported-by: David Ahern <dsahern@gmail.com>
Fixes: fc82d93e57 ("selftests: fib_rule_tests: fix local IPv4 address typo")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are series of patches that add SPDX tags to different kernel files,
based on two different things:
- SPDX entries are added to a bunch of files that we missed a year ago
that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the last
big sweep, or they were Makefile/Kconfig files, which we didn't
touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the next
few weeks as the tools and reviewers crunch through the more "odd"
variants of how to say "GPLv2" that developers have come up with over
the years, combined with other fun oddities (GPL + a BSD disclaimer?)
that are being unearthed, with the goal for the whole kernel to be
cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOP8uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmGQCgy3evqzleuOITDpuWaxewFdHqiJYAnA7KRw4H
1KwtfRnMtG6dk/XaS7H7
=O9lH
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
A test for the basic NAT functionality uses ip command which needs veth
device. There is a condition where the kernel support for veth is not
compiled into the kernel and the test script breaks. This patch contains
code for reasonable error display and correct code exit.
Signed-off-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When running under a pipe, some timer tests would not report output in
real-time because stdout flushes were missing after printf()s that lacked
a newline. This adds them to restore real-time status output that humans
can enjoy.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
As it turns out, the "stdbuf" command will actually force all
subprocesses into unbuffered output, and some implementations of "echo"
turn into single-character writes, which utterly wrecks writes to /sys
and /proc files.
Instead, drop the "stdbuf" usage, and for any tests that want explicit
flushing between newlines, they'll have to add "fflush(stdout);" as
needed.
Reported-by: Takashi Iwai <tiwai@suse.de>
Fixes: 5c069b6ded ("selftests: Move test output to diagnostic lines")
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Atom-based CPUs trigger stack fault when invoke 32-bit SYSENTER instruction
with invalid register values. So we also need SIGBUS handling in this case.
Following is assembly when the fault exception happens.
(gdb) disassemble $eip
Dump of assembler code for function __kernel_vsyscall:
0xf7fd8fe0 <+0>: push %ecx
0xf7fd8fe1 <+1>: push %edx
0xf7fd8fe2 <+2>: push %ebp
0xf7fd8fe3 <+3>: mov %esp,%ebp
0xf7fd8fe5 <+5>: sysenter
0xf7fd8fe7 <+7>: int $0x80
=> 0xf7fd8fe9 <+9>: pop %ebp
0xf7fd8fea <+10>: pop %edx
0xf7fd8feb <+11>: pop %ecx
0xf7fd8fec <+12>: ret
End of assembler dump.
According to Intel SDM, this could also be a Stack Segment Fault(#SS, 12),
except a normal Page Fault(#PF, 14). Especially, in section 6.9 of Vol.3A,
both stack and page faults are within the 10th(lowest priority) class, and
as it said, "exceptions within each class are implementation-dependent and
may vary from processor to processor". It's expected for processors like
Intel Atom to trigger stack fault(SIGBUS), while we get page fault(SIGSEGV)
from common Core processors.
Signed-off-by: Tong Bo <bo.tong@intel.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it would be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 6 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154043.007767574@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ever since commit 3a06c7ac24 ("posix-clocks: Remove interval timer
facility and mmap/fasync callbacks") the possibility of PHC based
posix timers has been removed. In addition it will probably never
make sense to implement this functionality.
This patch removes the misleading example code which seems to suggest
that posix timers for PHC devices will ever be a thing.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As all the testing addresses are in the same subnet and egress device ==
ingress device. We need enable forwarding to get the route entry.
Also disable rp_filer separately as some distributions enable it in
startup scripts.
Fixes: 65b2b4939a ("selftests: net: initial fib rule tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv4 testing address are all in 192.51.100.0 subnet. It doesn't make
sense to set a 198.51.100.1 local address. Should be a typo.
Fixes: 65b2b4939a ("selftests: net: initial fib rule tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:1) Use after free in __dev_map_entry_free(), from Eric Dumazet.
1) Use after free in __dev_map_entry_free(), from Eric Dumazet.
2) Fix TCP retransmission timestamps on passive Fast Open, from Yuchung
Cheng.
3) Orphan NFC, we'll take the patches directly into my tree. From
Johannes Berg.
4) We can't recycle cloned TCP skbs, from Eric Dumazet.
5) Some flow dissector bpf test fixes, from Stanislav Fomichev.
6) Fix RCU marking and warnings in rhashtable, from Herbert Xu.
7) Fix some potential fib6 leaks, from Eric Dumazet.
8) Fix a _decode_session4 uninitialized memory read bug fix that got
lost in a merge. From Florian Westphal.
9) Fix ipv6 source address routing wrt. exception route entries, from
Wei Wang.
10) The netdev_xmit_more() conversion was not done %100 properly in mlx5
driver, fix from Tariq Toukan.
11) Clean up botched merge on netfilter kselftest, from Florian
Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (74 commits)
of_net: fix of_get_mac_address retval if compiled without CONFIG_OF
net: fix kernel-doc warnings for socket.c
net: Treat sock->sk_drops as an unsigned int when printing
kselftests: netfilter: fix leftover net/net-next merge conflict
mlxsw: core: Prevent reading unsupported slave address from SFP EEPROM
mlxsw: core: Prevent QSFP module initialization for old hardware
vsock/virtio: Initialize core virtio vsock before registering the driver
net/mlx5e: Fix possible modify header actions memory leak
net/mlx5e: Fix no rewrite fields with the same match
net/mlx5e: Additional check for flow destination comparison
net/mlx5e: Add missing ethtool driver info for representors
net/mlx5e: Fix number of vports for ingress ACL configuration
net/mlx5e: Fix ethtool rxfh commands when CONFIG_MLX5_EN_RXNFC is disabled
net/mlx5e: Fix wrong xmit_more application
net/mlx5: Fix peer pf disable hca command
net/mlx5: E-Switch, Correct type to u16 for vport_num and int for vport_index
net/mlx5: Add meaningful return codes to status_to_err function
net/mlx5: Imply MLXFW in mlx5_core
Revert "tipc: fix modprobe tipc failed after switch order of device registration"
vsock/virtio: free packets during the socket release
...
Pull perf tooling updates from Ingo Molnar:
"perf.data:
- Streaming compression of perf ring buffer into
PERF_RECORD_COMPRESSED user space records, resulting in ~3-5x
perf.data file size reduction on variety of tested workloads what
saves storage space on larger server systems where perf.data size
can easily reach several tens or even hundreds of GiBs, especially
when profiling with DWARF-based stacks and tracing of context
switches.
perf record:
- Improve -user-regs/intr-regs suggestions to overcome errors
perf annotate:
- Remove hist__account_cycles() from callback, speeding up branch
processing (perf record -b)
perf stat:
- Add a 'percore' event qualifier, e.g.: -e
cpu/event=0,umask=0x3,percore=1/, that sums up the event counts for
both hardware threads in a core.
We can already do this with --per-core, but it's often useful to do
this together with other metrics that are collected per hardware
thread.
I.e. now its possible to do this per-event, and have it mixed with
other events not aggregated by core.
arm64:
- Map Brahma-B53 CPUID to cortex-a53 events.
- Add Cortex-A57 and Cortex-A72 events.
csky:
- Add DWARF register mappings for libdw, allowing --call-graph=dwarf
to work on the C-SKY arch.
x86:
- Add support for recording and printing XMM registers, available,
for instance, on Icelake.
- Add uncore_upi (Intel's "Ultra Path Interconnect" events) JSON
support. UPI replaced the Intel QuickPath Interconnect (QPI) in
Xeon Skylake-SP.
Intel PT:
- Fix instructions sampling rate.
- Timestamp fixes.
- Improve exported-sql-viewer GUI, allowing, for instance, to
copy'n'paste the trees, useful for e-mailing"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (73 commits)
perf stat: Support 'percore' event qualifier
perf stat: Factor out aggregate counts printing
perf tools: Add a 'percore' event qualifier
perf docs: Add description for stderr
perf intel-pt: Fix sample timestamp wrt non-taken branches
perf intel-pt: Fix improved sample timestamp
perf intel-pt: Fix instructions sampling rate
perf regs x86: Add X86 specific arch__intr_reg_mask()
perf parse-regs: Add generic support for arch__intr/user_reg_mask()
perf parse-regs: Split parse_regs
perf vendor events arm64: Add Cortex-A57 and Cortex-A72 events
perf vendor events arm64: Map Brahma-B53 CPUID to cortex-a53 events
perf vendor events arm64: Remove [[:xdigit:]] wildcard
perf jevents: Remove unused variable
perf test zstd: Fixup verbose mode output
perf tests: Implement Zstd comp/decomp integration test
perf inject: Enable COMPRESSED record decompression
perf report: Implement perf.data record decompression
perf record: Implement -z,--compression_level[=<n>] option
perf report: Add stub processing of compressed events for -D
...
Pull core fixes from Ingo Molnar:
"This fixes a particularly thorny munmap() bug with MPX, plus fixes a
host build environment assumption in objtool"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Allow AR to be overridden with HOSTAR
x86/mpx, mm/core: Fix recursive munmap() corruption
In nf-next, I had extended this script to also cover NAT support for the
inet family.
In nf, I extended it to cover a regression with 'fully-random' masquerade.
Make this script work again by resolving the conflicts as needed.
Fixes: 8b44836583 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
perf.data:
Alexey Budankov:
- Streaming compression of perf ring buffer into PERF_RECORD_COMPRESSED
user space records, resulting in ~3-5x perf.data file size reduction
on variety of tested workloads what saves storage space on larger
server systems where perf.data size can easily reach several tens or
even hundreds of GiBs, especially when profiling with DWARF-based
stacks and tracing of context switches.
perf record:
Arnaldo Carvalho de Melo
- Improve -user-regs/intr-regs suggestions to overcome errors.
perf annotate:
Jin Yao:
- Remove hist__account_cycles() from callback, speeding up branch processing
(perf record -b).
perf stat:
- Add a 'percore' event qualifier, e.g.: -e cpu/event=0,umask=0x3,percore=1/,
that sums up the event counts for both hardware threads in a core.
We can already do this with --per-core, but it's often useful to do
this together with other metrics that are collected per hardware thread.
I.e. now its possible to do this per-event, and have it mixed with other
events not aggregated by core.
core libraries:
Donald Yandt:
- Check for errors when doing fgets(/proc/version).
Jiri Olsa:
- Speed up report for perf compiled with linbunwind.
tools headers:
Arnaldo Carvalho de Melo
- Update memcpy_64.S, x86's kvm.h and pt_regs.h.
arm64:
Florian Fainelli:
- Map Brahma-B53 CPUID to cortex-a53 events.
- Add Cortex-A57 and Cortex-A72 events.
csky:
Mao Han:
- Add DWARF register mappings for libdw, allowing --call-graph=dwarf to work
on the C-SKY arch.
x86:
Andi Kleen/Kan Liang:
- Add support for recording and printing XMM registers, available, for
instance, on Icelake.
Kan Liang:
- Add uncore_upi (Intel's "Ultra Path Interconnect" events) JSON support.
UPI replaced the Intel QuickPath Interconnect (QPI) in Xeon Skylake-SP.
Intel PT:
Adrian Hunter
. Fix instructions sampling rate.
. Timestamp fixes.
. Improve exported-sql-viewer GUI, allowing, for instance, to copy'n'paste
the trees, useful for e-mailing.
Documentation:
Thomas Richter:
- Add description for 'perf --debug stderr=1', which redirects stderr to stdout.
libtraceevent:
Tzvetomir Stoyanov:
- Add man pages for the various APIs.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCXN8KEwAKCRCyPKLppCJ+
JxbAAPsE4bDD7UyTJgVWVXFyqMkaFURv9eGtmhbH/EhnZ/ADfwEAoUG6C+G2DLre
IMtgTXSlRShQucQbum5Rcp9lcXGL+gY=
=mGtw
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-5.2-20190517' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
perf.data:
Alexey Budankov:
- Streaming compression of perf ring buffer into PERF_RECORD_COMPRESSED
user space records, resulting in ~3-5x perf.data file size reduction
on variety of tested workloads what saves storage space on larger
server systems where perf.data size can easily reach several tens or
even hundreds of GiBs, especially when profiling with DWARF-based
stacks and tracing of context switches.
perf record:
Arnaldo Carvalho de Melo
- Improve -user-regs/intr-regs suggestions to overcome errors.
perf annotate:
Jin Yao:
- Remove hist__account_cycles() from callback, speeding up branch processing
(perf record -b).
perf stat:
- Add a 'percore' event qualifier, e.g.: -e cpu/event=0,umask=0x3,percore=1/,
that sums up the event counts for both hardware threads in a core.
We can already do this with --per-core, but it's often useful to do
this together with other metrics that are collected per hardware thread.
I.e. now its possible to do this per-event, and have it mixed with other
events not aggregated by core.
core libraries:
Donald Yandt:
- Check for errors when doing fgets(/proc/version).
Jiri Olsa:
- Speed up report for perf compiled with linbunwind.
tools headers:
Arnaldo Carvalho de Melo
- Update memcpy_64.S, x86's kvm.h and pt_regs.h.
arm64:
Florian Fainelli:
- Map Brahma-B53 CPUID to cortex-a53 events.
- Add Cortex-A57 and Cortex-A72 events.
csky:
Mao Han:
- Add DWARF register mappings for libdw, allowing --call-graph=dwarf to work
on the C-SKY arch.
x86:
Andi Kleen/Kan Liang:
- Add support for recording and printing XMM registers, available, for
instance, on Icelake.
Kan Liang:
- Add uncore_upi (Intel's "Ultra Path Interconnect" events) JSON support.
UPI replaced the Intel QuickPath Interconnect (QPI) in Xeon Skylake-SP.
Intel PT:
Adrian Hunter
. Fix instructions sampling rate.
. Timestamp fixes.
. Improve exported-sql-viewer GUI, allowing, for instance, to copy'n'paste
the trees, useful for e-mailing.
Documentation:
Thomas Richter:
- Add description for 'perf --debug stderr=1', which redirects stderr to stdout.
libtraceevent:
Tzvetomir Stoyanov:
- Add man pages for the various APIs.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2019-05-18
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix bpftool's raw BTF dump in relation to forward declarations of union/
structs, and another fix to unexport logging helpers, from Andrii.
2) Fix inode permission check for retrieving bpf programs, from Chenbo.
3) Fix bpftool to raise rlimit earlier as otherwise libbpf's feature probing
can fail and subsequently it refuses to load an object, from Yonghong.
4) Fix declaration of bpf_get_current_task() in kselftests, from Alexei.
5) Fix up BPF kselftest .gitignore to add generated files, from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* POWER: support for direct access to the POWER9 XIVE interrupt controller,
memory and performance optimizations.
* x86: support for accessing memory not backed by struct page, fixes and refactoring
* Generic: dirty page tracking improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc3qV/AAoJEL/70l94x66Dn3QH/jX1Bn0P/RZAIt4w0SySklSg
PqxUKDyBQqB9vN9Qeb9jWXAKPH2CtM3+up/rz7oRnBWp7qA6vXcC/R/QJYAvzdXE
nklsR/oYCsflR1KdlVYuDvvPCPP2fLBU5zfN83OsaBQ8fNRkm3gN+N5XQ2SbXbLy
Mo9tybS4otY201UAC96e8N0ipwwyCRpDneQpLcl+F5nH3RBt63cVbs04O+70MXn7
eT4I+8K3+Go7LATzT8hglD21D/7uvE31qQb6yr5L33IfhU4GB51RZzBXTNaAdY8n
hT1rMrRkAMAFWYZPQDfoMadjWU3i5DIfstKjDxOr9oTfuOEp5Z+GvJwvVnUDg1I=
=D0+p
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- support for SVE and Pointer Authentication in guests
- PMU improvements
POWER:
- support for direct access to the POWER9 XIVE interrupt controller
- memory and performance optimizations
x86:
- support for accessing memory not backed by struct page
- fixes and refactoring
Generic:
- dirty page tracking improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (155 commits)
kvm: fix compilation on aarch64
Revert "KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU"
kvm: x86: Fix L1TF mitigation for shadow MMU
KVM: nVMX: Disable intercept for FS/GS base MSRs in vmcs02 when possible
KVM: PPC: Book3S: Remove useless checks in 'release' method of KVM device
KVM: PPC: Book3S HV: XIVE: Fix spelling mistake "acessing" -> "accessing"
KVM: PPC: Book3S HV: Make sure to load LPID for radix VCPUs
kvm: nVMX: Set nested_run_pending in vmx_set_nested_state after checks complete
tests: kvm: Add tests for KVM_SET_NESTED_STATE
KVM: nVMX: KVM_SET_NESTED_STATE - Tear down old EVMCS state before setting new state
tests: kvm: Add tests for KVM_CAP_MAX_VCPUS and KVM_CAP_MAX_CPU_ID
tests: kvm: Add tests to .gitignore
KVM: Introduce KVM_CAP_MANUAL_DIRTY_LOG_PROTECT2
KVM: Fix kvm_clear_dirty_log_protect off-by-(minus-)one
KVM: Fix the bitmap range to copy during clear dirty
KVM: arm64: Fix ptrauth ID register masking logic
KVM: x86: use direct accessors for RIP and RSP
KVM: VMX: Use accessors for GPRs outside of dedicated caching logic
KVM: x86: Omit caching logic for always-available GPRs
kvm, x86: Properly check whether a pfn is an MMIO or not
...
kflag bit determines whether FWD is for struct or union. Use that bit.
Fixes: c93cc69004 ("bpftool: add ability to dump BTF types")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, this Makefile hardcodes GNU ar, meaning that if it is not
available, there is no way to supply a different one and the build will
fail.
$ make AR=llvm-ar CC=clang LD=ld.lld HOSTAR=llvm-ar HOSTCC=clang \
HOSTLD=ld.lld HOSTLDFLAGS=-fuse-ld=lld defconfig modules_prepare
...
AR /out/tools/objtool/libsubcmd.a
/bin/sh: 1: ar: not found
...
Follow the logic of HOST{CC,LD} and allow the user to specify a
different ar tool via HOSTAR (which is used elsewhere in other
tools/ Makefiles).
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: <stable@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/80822a9353926c38fd7a152991c6292491a9d0e8.1558028966.git.jpoimboe@redhat.com
Link: https://github.com/ClangBuiltLinux/linux/issues/481
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This kselftest second update for Linux 5.2-rc1 consists of
Kselftest framework fixes from Shuah Khan
- kselftest framework bpf build/test workflow regression fix
- Fix to kselftest install to use default install path
- Fix to kselftest KBUILD_OUTPUT builds to not clutter main
KBUILD_OUTPUT directory with selftest objects
- .gitignore fixes from Kelsey Skunberg
- rseq selftests updates from Mathieu Desnoyers and Martin Schwidefsky:
They change the per-architecture pre-abort signatures to ensure those
are valid trap instructions.
The way exit points are presented to debuggers is enhanced, ensuring
all exit points are present, so debuggers don't have to disassemble
rseq critical section to properly skip over them.
Discussions with the glibc community is reaching a consensus of exposing
a __rseq_handled symbol from glibc to coexist with rseq early adopters.
Update the rseq selftest code to expose and use this symbol.
Support for compiling asm goto with clang is added with the
"-no-integrated-as" compiler switch, similarly to the top level kernel
Makefile.
- kselftest Makefile test run output refactoring and making test
output TAP13 compliant from Kees Cook:
This re-factors the selftest Makefiles to extract the test running logic
to be reused between "run_tests" and "emit_tests", while also fixing
up the test output to be TAP version 13 compliant:
- added "plan" line
- fixed result line syntax
- moved all test output to be "# "-prefixed as TAP "diagnostic"
lines
The prefixing code includes a fallback mode for limited execution
environments.
Additionally, the plan lines are fixed for all callers of kselftest.h.
-----BEGIN PGP SIGNATURE-----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=LZRz
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull more kselftest updates from Shuah Khan:
- kselftest framework bpf build/test workflow regression fix
- Fix to kselftest install to use default install path
- Fix to kselftest KBUILD_OUTPUT builds to not clutter main
KBUILD_OUTPUT directory with selftest objects
- .gitignore fixes (Kelsey Skunberg)
- rseq selftests updates (Mathieu Desnoyers and Martin Schwidefsky)
They change the per-architecture pre-abort signatures to ensure those
are valid trap instructions.
The way exit points are presented to debuggers is enhanced, ensuring
all exit points are present, so debuggers don't have to disassemble
rseq critical section to properly skip over them.
Discussions with the glibc community is reaching a consensus of
exposing a __rseq_handled symbol from glibc to coexist with rseq
early adopters. Update the rseq selftest code to expose and use this
symbol.
Support for compiling asm goto with clang is added with the
"-no-integrated-as" compiler switch, similarly to the top level
kernel Makefile.
- kselftest Makefile test run output refactoring and making test output
TAP13 compliant from Kees Cook:
This re-factors the selftest Makefiles to extract the test running
logic to be reused between "run_tests" and "emit_tests", while also
fixing up the test output to be TAP version 13 compliant:
- added "plan" line
- fixed result line syntax
- moved all test output to be "# "-prefixed as TAP "diagnostic"
lines
The prefixing code includes a fallback mode for limited execution
environments.
Additionally, the plan lines are fixed for all callers of
kselftest.h.
* tag 'linux-kselftest-5.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (25 commits)
selftests: avoid KBUILD_OUTPUT dir cluttering with selftest objects
selftests: drivers: Create .gitignore to include /dma-buf/udmabuf
selftests: pidfd: Create .gitignore to include pidfd_test
selftests: fix bpf build/test workflow regression when KBUILD_OUTPUT is set
selftests: fix install target to use default install path
rseq/selftests: add -no-integrated-as for clang
rseq/selftests: mips: use break instruction for RSEQ_SIG
rseq/selftests: powerpc code signature: generate valid instructions
rseq/selftests: aarch64 code signature: handle big-endian environment
rseq/selftests: arm: use udf instruction for RSEQ_SIG
rseq/selftests: s390: use trap4 for RSEQ_SIG
rseq/selftests: x86: use ud1 instruction as RSEQ_SIG opcode
rseq/selftests: s390: use jg instruction for jumps outside of the asm
rseq/selftests: Use __rseq_handled symbol to coexist with glibc
rseq/selftests: Introduce __rseq_cs_ptr_array, rename __rseq_table to __rseq_cs
rseq/selftests: Add __rseq_exit_point_array section for debuggers
rseq/selftests: x86: Work-around bogus gcc-8 optimisation
selftests: Add test plan API to kselftest.h and adjust callers
selftests: Remove KSFT_TAP_LEVEL
selftests: Move test output to diagnostic lines
...
The first command in setup_xfrm is failing resulting in the test getting
skipped:
+ ip netns exec ns-B ip -6 xfrm state add src fd00:1::a dst fd00:1::b spi 0x1000 proto esp aead 'rfc4106(gcm(aes))' 0x0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f0f 128 mode tunnel
+ out=RTNETLINK answers: Function not implemented
...
xfrm6 not supported
TEST: vti6: PMTU exceptions [SKIP]
xfrm4 not supported
TEST: vti4: PMTU exceptions [SKIP]
...
The setup command started failing when the run_cmd option was added.
Removing the quotes fixes the problem:
...
TEST: vti6: PMTU exceptions [ OK ]
TEST: vti4: PMTU exceptions [ OK ]
...
Fixes: 56490b623a ("selftests: Add debugging options to pmtu.sh")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
libbpf_util.h header was recently exposed as public as a dependency of
xsk.h. In addition to memory barriers, it contained logging helpers,
which are not supposed to be exposed. This patch moves those into
libbpf_internal.h, which is kept as an internal header.
Cc: Stanislav Fomichev <sdf@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Fixes: 7080da8909 ("libbpf: add libbpf_util.h to header install.")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
For a host which has a lower rlimit for max locked memory (e.g., 64KB),
the following error occurs in one of our production systems:
# /usr/sbin/bpftool prog load /paragon/pods/52877437/home/mark.o \
/sys/fs/bpf/paragon_mark_21 type cgroup/skb \
map idx 0 pinned /sys/fs/bpf/paragon_map_21
libbpf: Error in bpf_object__probe_name():Operation not permitted(1).
Couldn't load basic 'r0 = 0' BPF program.
Error: failed to open object file
The reason is due to low locked memory during bpf_object__probe_name()
which probes whether program name is supported in kernel or not
during __bpf_object__open_xattr().
bpftool program load already tries to relax mlock rlimit before
bpf_object__load(). Let us move set_max_rlimit() before
__bpf_object__open_xattr(), which fixed the issue here.
Fixes: 47eff61777 ("bpf, libbpf: introduce bpf_object__probe_caps to test BPF capabilities")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Pull core fixes from Ingo Molnar:
"A handful of objtool updates, plus a documentation addition for
__ab_c_size()"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix whitelist documentation typo
objtool: Fix function fallthrough detection
objtool: Don't use ignore flag for fake jumps
overflow.h: Add comment documenting __ab_c_size()
With this patch, we can use the 'percore' event qualifier in perf-stat.
root@skl:/tmp# perf stat -e cpu/event=0,umask=0x3,percore=1/,cpu/event=0,umask=0x3/ -a -A -I1000
1.000773050 S0-C0 98,352,832 cpu/event=0,umask=0x3,percore=1/ (50.01%)
1.000773050 S0-C1 103,763,057 cpu/event=0,umask=0x3,percore=1/ (50.02%)
1.000773050 S0-C2 196,776,995 cpu/event=0,umask=0x3,percore=1/ (50.02%)
1.000773050 S0-C3 176,493,779 cpu/event=0,umask=0x3,percore=1/ (50.02%)
1.000773050 CPU0 47,699,641 cpu/event=0,umask=0x3/ (50.02%)
1.000773050 CPU1 49,052,451 cpu/event=0,umask=0x3/ (49.98%)
1.000773050 CPU2 102,771,422 cpu/event=0,umask=0x3/ (49.98%)
1.000773050 CPU3 100,784,662 cpu/event=0,umask=0x3/ (49.98%)
1.000773050 CPU4 43,171,342 cpu/event=0,umask=0x3/ (49.98%)
1.000773050 CPU5 54,152,158 cpu/event=0,umask=0x3/ (49.98%)
1.000773050 CPU6 93,618,410 cpu/event=0,umask=0x3/ (49.98%)
1.000773050 CPU7 74,477,589 cpu/event=0,umask=0x3/ (49.99%)
In this example, we count the event 'ref-cycles' per-core and per-CPU in
one perf stat command-line. From the output, we can see:
S0-C0 = CPU0 + CPU4
S0-C1 = CPU1 + CPU5
S0-C2 = CPU2 + CPU6
S0-C3 = CPU3 + CPU7
So the result is expected (tiny difference is ignored).
Note that, the 'percore' event qualifier needs to use with option '-A'.
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1555077590-27664-4-git-send-email-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Move the aggregate counts printing to a new function
print_counter_aggrdata, which will be used in following patches.
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1555077590-27664-3-git-send-email-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a 'percore' event qualifier, like cpu/event=0,umask=0x3,percore=1/,
that sums up the event counts for both hardware threads in a core.
We can already do this with --per-core, but it's often useful to do
this together with other metrics that are collected per hardware thread.
So we need to support this per-core counting on a event level.
This can be implemented in only the user tool, no kernel support needed.
v4:
---
1. Add Arnaldo's patch which updates the documentation for
this new qualifier.
2. Rebase to latest perf/core branch
v3:
---
Simplify the code according to Jiri's comments.
Before:
"return term->val.percore ? true : false;"
Now:
"return term->val.percore;"
v2:
---
Change the qualifier name from 'coresum' to 'percore' according to
comments from Jiri and Andi.
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jin Yao <yao.jin@intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1555077590-27664-2-git-send-email-yao.jin@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
'perf report' displays recorded data on the screen and emits warnings
and debug messages in the status line (last one on screen).
perf also supports the possibility to write all debug messages to stderr
(instead of writing them to the status line).
This is achieved with the following command:
# ./perf --debug stderr=1 report -vvvvv -i ~/fast.data 2>/tmp/2
# ll /tmp/2
-rw-rw-r-- 1 tmricht tmricht 5420835 May 7 13:46 /tmp/2
#
The usage of variable stderr=1 is not documented, so add it to the perf
man page.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20190513080220.91966-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The sample timestamp is updated to ensure that the timestamp represents
the time of the sample and not a branch that the decoder is still
walking towards. The sample timestamp is updated when the decoder
returns, but the decoder does not return for non-taken branches. Update
the sample timestamp then also.
Note that commit 3f04d98e97 ("perf intel-pt: Improve sample
timestamp") was also a stable fix and appears, for example, in v4.4
stable tree as commit a4ebb58fd124 ("perf intel-pt: Improve sample
timestamp").
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: 3f04d98e97 ("perf intel-pt: Improve sample timestamp")
Link: http://lkml.kernel.org/r/20190510124143.27054-4-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The decoder uses its current timestamp in samples. Usually that is a
timestamp that has already passed, but in some cases it is a timestamp
for a branch that the decoder is walking towards, and consequently
hasn't reached.
The intel_pt_sample_time() function decides which is which, but was not
handling TNT packets exactly correctly.
In the case of TNT, the timestamp applies to the first branch, so the
decoder must first walk to that branch.
That means intel_pt_sample_time() should return true for TNT, and this
patch makes that change. However, if the first branch is a non-taken
branch (i.e. a 'N'), then intel_pt_sample_time() needs to return false
for subsequent taken branches in the same TNT packet.
To handle that, introduce a new state INTEL_PT_STATE_TNT_CONT to
distinguish the cases.
Note that commit 3f04d98e97 ("perf intel-pt: Improve sample
timestamp") was also a stable fix and appears, for example, in v4.4
stable tree as commit a4ebb58fd124 ("perf intel-pt: Improve sample
timestamp").
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v4.4+
Fixes: 3f04d98e97 ("perf intel-pt: Improve sample timestamp")
Link: http://lkml.kernel.org/r/20190510124143.27054-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The timestamp used to determine if an instruction sample is made, is an
estimate based on the number of instructions since the last known
timestamp. A consequence is that it might go backwards, which results in
extra samples. Change it so that a sample is only made when the
timestamp goes forwards.
Note this does not affect a sampling period of 0 or sampling periods
specified as a count of instructions.
Example:
Before:
$ perf script --itrace=i10us
ls 13812 [003] 2167315.222583: 3270 instructions:u: 7fac71e2e494 __GI___tunables_init+0xf4 (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 30902 instructions:u: 7fac71e2da0f _dl_cache_libcmp+0x2f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 10 instructions:u: 7fac71e2d9ff _dl_cache_libcmp+0x1f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 8 instructions:u: 7fac71e2d9ea _dl_cache_libcmp+0xa (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 14 instructions:u: 7fac71e2d9ea _dl_cache_libcmp+0xa (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 6 instructions:u: 7fac71e2d9ff _dl_cache_libcmp+0x1f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 14 instructions:u: 7fac71e2d9ff _dl_cache_libcmp+0x1f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 4 instructions:u: 7fac71e2dab2 _dl_cache_libcmp+0xd2 (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222728: 16423 instructions:u: 7fac71e2477a _dl_map_object_deps+0x1ba (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222734: 12731 instructions:u: 7fac71e27938 _dl_name_match_p+0x68 (/lib/x86_64-linux-gnu/ld-2.28.so)
...
After:
$ perf script --itrace=i10us
ls 13812 [003] 2167315.222583: 3270 instructions:u: 7fac71e2e494 __GI___tunables_init+0xf4 (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222667: 30902 instructions:u: 7fac71e2da0f _dl_cache_libcmp+0x2f (/lib/x86_64-linux-gnu/ld-2.28.so)
ls 13812 [003] 2167315.222728: 16479 instructions:u: 7fac71e2477a _dl_map_object_deps+0x1ba (/lib/x86_64-linux-gnu/ld-2.28.so)
...
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Fixes: f4aa081949 ("perf tools: Add Intel PT decoder")
Link: http://lkml.kernel.org/r/20190510124143.27054-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
XMM registers can be collected on Icelake and later platforms.
Add specific arch__intr_reg_mask(), which creating an event to check if
the kernel and hardware can collect XMM registers.
Test on Skylake which doesn't support XMM registers collection. There is
nothing changed.
#perf record -I?
available registers: AX BX CX DX SI DI BP SP IP FLAGS CS SS R8 R9
R10 R11 R12 R13 R14 R15
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-I, --intr-regs[=<any register>]
sample selected machine registers on
interrupt, use '-I?' to list register names
#perf record -I
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.905 MB perf.data (2520 samples) ]
#perf evlist -v
cycles: size: 112, { sample_period, sample_freq }: 4000, sample_type:
IP|TID|TIME|CPU|PERIOD|REGS_INTR, read_format: ID, disabled: 1,
inherit: 1, mmap: 1, comm: 1, freq: 1, task: 1, precise_ip: 3,
sample_id_all: 1, exclude_guest: 1, mmap2: 1, comm_exec: 1, ksymbol:
1, bpf_event: 1, sample_regs_intr: 0xff0fff
Test on Icelake which support XMM registers collection.
#perf record -I?
available registers: AX BX CX DX SI DI BP SP IP FLAGS CS SS R8 R9 R10
R11 R12 R13 R14 R15 XMM0 XMM1 XMM2 XMM3 XMM4 XMM5 XMM6 XMM7 XMM8 XMM9
XMM10 XMM11 XMM12 XMM13 XMM14 XMM15
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-I, --intr-regs[=<any register>]
sample selected machine registers on
interrupt, use '-I?' to list register names
#perf record -I
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.800 MB perf.data (318 samples) ]
#perf evlist -v
cycles: size: 112, { sample_period, sample_freq }: 4000, sample_type:
IP|TID|TIME|CPU|PERIOD|REGS_INTR, read_format: ID, disabled: 1,
inherit: 1, mmap: 1, comm: 1, freq: 1, task: 1, precise_ip: 3,
sample_id_all: 1, exclude_guest: 1, mmap2: 1, comm_exec: 1, ksymbol:
1, bpf_event: 1, sample_regs_intr: 0xffffffff00ff0fff
Committer notes:
Don't set attr.sample_period as a named struct init, as it is part of an
unnamed union in 'struct perf_event_attr', and doing so breaks the build
on older gcc versions, such as:
gcc version 4.1.2 20080704 (Red Hat 4.1.2-55)
gcc version 4.4.7 20120313 (Red Hat 4.4.7-23) (GCC)
arch/x86/util/perf_regs.c: In function 'arch__intr_reg_mask':
arch/x86/util/perf_regs.c:279: error: unknown field 'sample_period' specified in initializer
cc1: warnings being treated as errors
arch/x86/util/perf_regs.c:279: warning: missing braces around initializer
arch/x86/util/perf_regs.c:279: warning: (near initialization for 'attr.<anonymous>')
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
[ Only on a lenovo t480s, a skylake machine, where the XMM registers didn't show up in -I?/--user-regs=? as expected ]
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1557865174-56264-3-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There may be different register mask for use with intr or user on some
platforms, e.g. Icelake.
Add weak functions arch__intr_reg_mask() and arch__user_reg_mask() to
return intr and user register mask respectively.
Check mask before printing or comparing the register name.
Generic code always return PERF_REGS_MASK. No functional change.
Suggested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1557865174-56264-2-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
* Fix a long standing namespace label corruption scenario when
re-provisioning capacity for a namespace.
* Restore the ability of the dax_pmem module to be built-in.
* Harden the build for the 'nfit_test' unit test modules so that the
userspace test harness can ensure all required test modules are
available.
-----BEGIN PGP SIGNATURE-----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=QM33
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-fixes-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"Just a small collection of fixes this time around.
The new virtio-pmem driver is nearly ready, but some last minute
device-mapper acks and virtio questions made it prudent to await v5.3.
Other major topics that were brewing on the linux-nvdimm mailing list
like sub-section hotplug, and other devm_memremap_pages() reworks will
go upstream through Andrew's tree.
Summary:
- Fix a long standing namespace label corruption scenario when
re-provisioning capacity for a namespace.
- Restore the ability of the dax_pmem module to be built-in.
- Harden the build for the 'nfit_test' unit test modules so that the
userspace test harness can ensure all required test modules are
available"
* tag 'libnvdimm-fixes-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
drivers/dax: Allow to include DEV_DAX_PMEM as builtin
libnvdimm/namespace: Fix label tracking error
tools/testing/nvdimm: add watermarks for dax_pmem* modules
dax/pmem: Fix whitespace in dax_pmem
Daniel Borkmann says:
====================
pull-request: bpf 2019-05-16
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a use after free in __dev_map_entry_free(), from Eric.
2) Several sockmap related bug fixes: a splat in strparser if
it was never initialized, remove duplicate ingress msg list
purging which can race, fix msg->sg.size accounting upon
skb to msg conversion, and last but not least fix a timeout
bug in tcp_bpf_wait_data(), from John.
3) Fix LRU map to avoid messing with eviction heuristics upon
syscall lookup, e.g. map walks from user space side will
then lead to eviction of just recently created entries on
updates as it would mark all map entries, from Daniel.
4) Don't bail out when libbpf feature probing fails. Also
various smaller fixes to flow_dissector test, from Stanislav.
5) Fix missing brackets for BTF_INT_OFFSET() in UAPI, from Gary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Handle meta data in GRUB_MENU
- Add variable to cusomize what return value the reboot code should return.
- Add support for grub2bls boot loader
- Show name and test iteration number in error message sent in mail
- Minor fixes and clean ups
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXNxRZxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qrVCAP4rgnMgMsPOt0cMtKty1Z3uA6njfrZc
UU1gNeHEvKr1MQEAhYy4N5FCigBygALEczmUIYwrzVq3luNPTwgUeUIH3AY=
=BTC7
-----END PGP SIGNATURE-----
Merge tag 'ktest-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull more ktest updates from Steven Rostedt:
- Add support for grub2bls boot loader
- Show name and test iteration number in error message sent in mail
- Minor fixes and clean ups
* tag 'ktest-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: update sample.conf for grub2bls
ktest: remove get_grub2_index
ktest: pass KERNEL_VERSION to POST_KTEST
ktest: introduce grub2bls REBOOT_TYPE option
ktest: cleanup get_grub_index
ktest: introduce _get_grub_index
In case we are not running in a namespace (which we don't do by default),
let's try to detach the bpf program that we use for eth_get_headlen tests.
Fixes: 0905beec9f ("selftests/bpf: run flow dissector tests in skb-less mode")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Otherwise, in case of an error, everything gets mushed together.
Fixes: a5cb33464e ("selftests/bpf: make flow dissector tests more extensible")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Otherwise libbpf is unusable from unprivileged process with
kernel.kernel.unprivileged_bpf_disabled=1.
All I get is EPERM from the probes, even if I just want to
open an ELF object and look at what progs/maps it has.
Instead of dying on probes, let's just pr_debug the error and
try to continue.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
- Removing of non-DYNAMIC_FTRACE from 32bit x86
- Removing of mcount support from x86
- Emulating a call from int3 on x86_64, fixes live kernel patching
- Consolidated Tracing Error logs file
Minor updates:
- Removal of klp_check_compiler_support()
- kdb ftrace dumping output changes
- Accessing and creating ftrace instances from inside the kernel
- Clean up of #define if macro
- Introduction of TRACE_EVENT_NOP() to disable trace events based on config
options
And other minor fixes and clean ups
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXNxMZxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qq4PAP44kP6VbwL8CHyI2A3xuJ6Hwxd+2Z2r
ip66RtzyJ+2iCgEA2QCuWUlEt2bLpF9a8IQ4N9tWenSeW2i7gunPb+tioQw=
=RVQo
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"The major changes in this tracing update includes:
- Removal of non-DYNAMIC_FTRACE from 32bit x86
- Removal of mcount support from x86
- Emulating a call from int3 on x86_64, fixes live kernel patching
- Consolidated Tracing Error logs file
Minor updates:
- Removal of klp_check_compiler_support()
- kdb ftrace dumping output changes
- Accessing and creating ftrace instances from inside the kernel
- Clean up of #define if macro
- Introduction of TRACE_EVENT_NOP() to disable trace events based on
config options
And other minor fixes and clean ups"
* tag 'trace-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (44 commits)
x86: Hide the int3_emulate_call/jmp functions from UML
livepatch: Remove klp_check_compiler_support()
ftrace/x86: Remove mcount support
ftrace/x86_32: Remove support for non DYNAMIC_FTRACE
tracing: Simplify "if" macro code
tracing: Fix documentation about disabling options using trace_options
tracing: Replace kzalloc with kcalloc
tracing: Fix partial reading of trace event's id file
tracing: Allow RCU to run between postponed startup tests
tracing: Fix white space issues in parse_pred() function
tracing: Eliminate const char[] auto variables
ring-buffer: Fix mispelling of Calculate
tracing: probeevent: Fix to make the type of $comm string
tracing: probeevent: Do not accumulate on ret variable
tracing: uprobes: Re-enable $comm support for uprobe events
ftrace/x86_64: Emulate call function while updating in breakpoint handler
x86_64: Allow breakpoints to emulate call instructions
x86_64: Add gap to int3 to allow for call emulation
tracing: kdb: Allow ftdump to skip all but the last few entries
tracing: Add trace_total_entries() / trace_total_entries_cpu()
...
The available registers for --int-regs and --user-regs may be different,
e.g. XMM registers.
Split parse_regs into two dedicated functions for --int-regs and
--user-regs respectively.
Modify the warning message. "--user-regs=?" should be applied to show
the available registers for --user-regs.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Tested-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1557865174-56264-1-git-send-email-kan.liang@linux.intel.com
[ Changed docs as suggested by Ravi and agreed by Kan ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The Cortex-A57 and Cortex-A72 both support all ARMv8 recommended events
up to the RC_ST_SPEC (0x91) event with the exception of:
- L1D_CACHE_REFILL_INNER (0x44)
- L1D_CACHE_REFILL_OUTER (0x45)
- L1D_TLB_RD (0x4E)
- L1D_TLB_WR (0x4F)
- L2D_TLB_REFILL_RD (0x5C)
- L2D_TLB_REFILL_WR (0x5D)
- L2D_TLB_RD (0x5E)
- L2D_TLB_WR (0x5F)
- STREX_SPEC (0x6F)
Create an appropriate JSON file for mapping those events and update the
mapfile.csv for matching the Cortex-A57 and Cortex-A72 MIDR to that
file.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sean V Kelley <seanvk.dev@oregontracks.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org (moderated list:arm pmu profiling and debugging)
Link: http://lkml.kernel.org/r/20190513202522.9050-4-f.fainelli@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Broadcom's Brahma-B53 CPUs support the same type of events that the
Cortex-A53 supports, recognize its CPUID and map it to the cortex-a53
events.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sean V Kelley <seanvk.dev@oregontracks.org>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org (moderated list
Link: http://lkml.kernel.org/r/20190513202522.9050-3-f.fainelli@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
ARM64's implementation of get_cpuidr_str() masks out the revision bits
[3:0] while reading the CPU identifier, there is no need for the
[[:xdigit:]] wildcard.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sean V Kelley <seanvk.dev@oregontracks.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org (moderated list:arm pmu profiling and debugging)
Link: http://lkml.kernel.org/r/20190513202522.9050-2-f.fainelli@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The shell tests should not redirect useful output to /dev/null, as that
is done automatically by 'perf test' in non verbose mode, so remove that
from the zstd comp/decomp test, fixing up verbose mode.
Before:
$ perf test zstd
68: Zstd perf.data compression/decompression : Ok
$ perf test -v zstd
68: Zstd perf.data compression/decompression :
--- start ---
test child forked, pid 11956
-z, --compression-level[=<n>]
Collecting compressed record file:
Checking compressed events stats:
test child finished with 0
---- end ----
Zstd perf.data compression/decompression: Ok
$
Now:
$ perf test zstd
68: Zstd perf.data compression/decompression : Ok
$ perf test -v zstd
68: Zstd perf.data compression/decompression :
--- start ---
test child forked, pid 12695
Collecting compressed record file:
0+500 records in
72+1 records out
37361 bytes (37 kB, 36 KiB) copied, 9.83796 s, 3.8 kB/s
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.001 MB /tmp/perf.data.rzq, compressed (original 0.004 MB, ratio is 3.679) ]
Checking compressed events stats:
# compressed : Zstd, level = 1, ratio = 4
COMPRESSED events: 3
test child finished with 0
---- end ----
Zstd perf.data compression/decompression: Ok
$
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/n/tip-tp96618ds42zic94nlh0msz3@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Introduce a basic integration test for Zstd based record
compression/decompression using 'perf record' and 'perf report'.
Committer notes:
Reduce a bit the freq (from 25 kHz to 5 kHz) and the number of /dev/null
records read (from 1000 to 500), reducing the time it takes to something
more in line with the time existing 'perf test' entries take to run.
With that in place:
$ time perf test zstd
68: Zstd perf.data compression/decompression : Ok
real 0m10.376s
user 0m0.105s
sys 0m0.440s
$ grep "model name" /proc/cpuinfo | head -1
model name : Intel(R) Core(TM) i7-8650U CPU @ 1.90GHz
$
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/dc007ae4-104a-2b7c-316e-275929025f0d@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Initialized decompression part of Zstd based API so COMPRESSED records
would be decompressed into the resulting output data file.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/c27d7500-ecdd-3569-cab5-8f70bbed5ea4@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
zstd_init(, comp_level = 0) initializes decompression part of API only
hat now consists of zstd_decompress_stream() function.
The perf.data PERF_RECORD_COMPRESSED records are decompressed using
zstd_decompress_stream() function into a linked list of mmaped memory
regions of mmap_comp_len size (struct decomp).
After decompression of one COMPRESSED record its content is iterated and
fetched for usual processing. The mmaped memory regions with
decompressed events are kept in the linked list till the tool process
termination.
When dumping raw records (e.g., perf report -D --header) file offsets of
events from compressed records are printed as zero.
Committer notes:
Since now we have support for processing PERF_RECORD_COMPRESSED, we see
none, in raw form, like we saw in the previous patch commiter notes,
they were decompressed into the usual PERF_RECORD_{FORK,MMAP,COMM,etc}
records, we only see the stats for those PERF_RECORD_COMPRESSED events,
and since I used the file generated in the commiter notes for the
previous patch, there they are, 2 compressed records:
$ perf report --header-only | grep cmdline
# cmdline : /home/acme/bin/perf record -z2 sleep 1
$ perf report -D | grep COMPRESS
COMPRESSED events: 2
COMPRESSED events: 0
$ perf report --stdio
# To display the perf.data header info, please use --header/--header-only options.
#
#
# Total Lost Samples: 0
#
# Samples: 15 of event 'cycles:u'
# Event count (approx.): 962227
#
# Overhead Command Shared Object Symbol
# ........ ....... ................ ...........................
#
46.99% sleep libc-2.28.so [.] _dl_addr
29.24% sleep [unknown] [k] 0xffffffffaea00a67
16.45% sleep libc-2.28.so [.] __GI__IO_un_link.part.1
5.92% sleep ld-2.28.so [.] _dl_setup_hash
1.40% sleep libc-2.28.so [.] __nanosleep
0.00% sleep [unknown] [k] 0xffffffffaea00163
#
# (Tip: To see callchains in a more compact form: perf report -g folded)
#
$
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/304b0a59-942c-3fe1-da02-aa749f87108b@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Implemented -z,--compression_level[=<n>] option that enables compression
of mmaped kernel data buffers content in runtime during perf record mode
collection. Default option value is 1 (fastest compression).
Compression overhead has been measured for serial and AIO streaming when
profiling matrix multiplication workload:
-------------------------------------------------------------
| SERIAL | AIO-1 |
----------------------------------------------------------------|
|-z | OVH(x) | ratio(x) size(MiB) | OVH(x) | ratio(x) size(MiB) |
|---------------------------------------------------------------|
| 0 | 1,00 | 1,000 179,424 | 1,00 | 1,000 187,527 |
| 1 | 1,04 | 8,427 181,148 | 1,01 | 8,474 188,562 |
| 2 | 1,07 | 8,055 186,953 | 1,03 | 7,912 191,773 |
| 3 | 1,04 | 8,283 181,908 | 1,03 | 8,220 191,078 |
| 5 | 1,09 | 8,101 187,705 | 1,05 | 7,780 190,065 |
| 8 | 1,05 | 9,217 179,191 | 1,12 | 6,111 193,024 |
-----------------------------------------------------------------
OVH = (Execution time with -z N) / (Execution time with -z 0)
ratio - compression ratio
size - number of bytes that was compressed
size ~= trace size x ratio
Committer notes:
Testing it I noticed that it failed to disable build id processing when
compression is enabled, and as we'd have to uncompress everything to
look for the PERF_RECORD_{MMAP,SAMPLE,etc} to figure out which build ids
to read from DSOs, we better disable build id processing when
compression is enabled, logging with pr_debug() when doing so:
Original patch:
# perf record -z2
^C[ perf record: Woken up 1 times to write data ]
0x1746e0 [0x76]: failed to process type: 81 [Invalid argument]
[ perf record: Captured and wrote 1.568 MB perf.data, compressed (original 0.452 MB, ratio is 3.995) ]
#
After auto-disabling build id processing when compression is enabled:
$ perf record -z2 sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.001 MB perf.data, compressed (original 0.001 MB, ratio is 2.292) ]
$ perf record -v -z2 sleep 1
Compression enabled, disabling build id collection at the end of the session.
<SNIP extra -v pr_debug() messages>
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.001 MB perf.data, compressed (original 0.001 MB, ratio is 2.305) ]
$
Also, with parts of the patch originally after this one moved to just
before this one we get:
$ perf record -z2 sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.001 MB perf.data, compressed (original 0.001 MB, ratio is 2.371) ]
$ perf report -D | grep COMPRESS
0 0x1b8 [0x155]: PERF_RECORD_COMPRESSED: unhandled!
0 0x30d [0x80]: PERF_RECORD_COMPRESSED: unhandled!
COMPRESSED events: 2
COMPRESSED events: 0
$
I.e. when faced with PERF_RECORD_COMPRESSED that we still have no code
to process, we just show it as not being handled, skip them and
continue, while before we had:
$ perf report -D | grep COMPRESS
0x1b8 [0x169]: failed to process type: 81 [Invalid argument]
Error:
failed to process sample
0 0x1b8 [0x169]: PERF_RECORD_COMPRESSED
$
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/9ff06518-ae63-a908-e44d-5d9e56dd66d9@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Committer note:
Split from a larger patch, this only dumps PERF_RECORD_COMPRESSED as
unhandled, so that when we introduce the record part in the next patch,
we don't see unhandled events when using 'perf record -D'.
Changed it so that we dump the event if the handler is just a stub, i.e.
for the case where we don't have ZSTD linked but we're processing a
perf.data file generated by a tool with that linked.
Also when failing to decompress we can't just dump the uncompressed
event and return 0, we have to propagate the error.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/304b0a59-942c-3fe1-da02-aa749f87108b@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Compression is implemented using the functions from zstd.c. As the memory
to operate on the compression uses mmap->aio.data[] buffers. If Zstd
streaming compression API fails for some reason the data to be compressed
are just copied into the memory buffers using plain memcpy().
Compressed trace frame consists of an array of PERF_RECORD_COMPRESSED
records. Each element of the array is not longer that PERF_SAMPLE_MAX_SIZE
and consists of perf_event_header followed by the compressed chunk
that is decompressed on the loading stage.
perf_mmap__aio_push() is replaced by perf_mmap__push() which is now used
in the both serial and AIO streaming cases. perf_mmap__push() is extended
with positive return values to signify absence of data ready for
processing.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/77db2b2c-5d03-dbb0-aeac-c4dd92129ab9@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Compression is implemented using the functions from zstd.c. As the
memory to operate on the compression uses mmap->data buffer.
If Zstd streaming compression API fails for some reason the data to be
compressed are just copied into the memory buffers using plain memcpy().
Compressed trace frame consists of an array of PERF_RECORD_COMPRESSED
records. Each element of the array is not longer that
PERF_SAMPLE_MAX_SIZE and consists of perf_event_header followed by the
compressed chunk that is decompressed on the loading stage.
Comitter notes:
Undo some unnecessary line breaks, remove some unnecessary () around
zstd_data to then just get its address, and fix conflicts with
BPF_PROG_INFO/BPF_BTF patchkits.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/744df43f-3932-2594-ddef-1e99a3cad03a@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Implemented functions are based on Zstd streaming compression API.
The functions are used in runtime to compress data that come from mmaped
kernel buffer. zstd_init(), zstd_fini() are used for initialization and
finalization to allocate and deallocate internal zstd objects.
zstd_compress_stream_to_records() is used to convert parts of mmaped
kernel buffer into an array of PERF_RECORD_COMPRESSED records.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/18bf36f3-b85a-1fe2-dd83-10e0c6069568@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Implemented mmap data buffer that is used as the memory to operate
on when compressing data in case of serial trace streaming.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/49b31321-0f70-392b-9a4f-649d3affe090@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Implemented PERF_RECORD_COMPRESSED event, related data types, header
feature and functions to write, read and print feature attributes from
the trace header section.
comp_mmap_len preserves the size of mmaped kernel buffer that was used
during collection. comp_mmap_len size is used on loading stage as the
size of decomp buffer for decompression of COMPRESSED events content.
Committer notes:
Fixed up conflict with BPF_PROG_INFO and BTF_BTF header features.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/ebbaf031-8dda-3864-ebc6-7922d43ee515@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Define 'bytes_transferred' and 'bytes_compressed' metrics to calculate
ratio in the end of the data collection:
compression ratio = bytes_transferred / bytes_compressed
The 'bytes_transferred' metric accumulates the amount of bytes that was
extracted from the mmaped kernel buffers for compression, while
'bytes_compressed' accumulates the amount of bytes that was received
after applying compression.
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1d4bf499-cb03-26dc-6fc6-f14fec7622ce@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
So that we can test the ifdef parts for this feature.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/n/tip-7o65mfl10wlvm8v3f0ombxd1@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Initial support for libtraceevent man pages - Documentation directory,
templates, configurations, Makefiles.
The first man page is also part of the patch - summary of the library
and all its APIs.
Building of the documentation is integrated into the libtraceevent build
process, new targets are added to its Makefile:
make help
make doc
make doc-clean
make doc-install
make doc-uninstall
Signed-off-by: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: linux-trace-devel@vger.kernel.org
Link: http://lore.kernel.org/linux-trace-devel/20190503091119.23399-2-tstoyanov@vmware.com
Link: http://lkml.kernel.org/r/20190510200106.104812629@goodmis.org
[ Replaced tracefs tracing/events to tracefs events in DESCRIPTION section ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
If fgets() fails due to any other error besides end-of-file, the version
char array may not even be null-terminated.
Signed-off-by: Donald Yandt <donald.yandt@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Fixes: a1645ce12a ("perf: 'perf kvm' tool for monitoring guest performance from host")
Link: http://lkml.kernel.org/r/20190514110100.22019-1-donald.yandt@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Perf cannot parse UPI (Intel's "Ultra Path Interconnect" [1]) events.
# perf stat -e UPI_DATA_BANDWIDTH_TX
event syntax error: 'UPI_DATA_BANDWIDTH_TX'
\___ parser error
Run 'perf list' for a list of valid events
The JSON lists call the box UPI LL, while perf calls it upi. Add
conversion support to JSON to convert the unit properly.
Committer notes:
[1] https://en.wikipedia.org/wiki/Intel_Ultra_Path_Interconnect
"The Intel Ultra Path Interconnect (UPI) is a point-to-point processor
interconnect developed by Intel which replaced the Intel QuickPath
Interconnect (QPI) in Xeon Skylake-SP platforms starting in 2017.
UPI is a low-latency coherent interconnect for scalable multiprocessor
systems with a shared address space. It uses a directory-based home
snoop coherency protocol with a transfer speed of up to 10.4 GT/s.
Supporting processors typically have two or three UPI links."
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1557234991-130456-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
With support for Python 2 or 3 and PySide 1 or 2 (Qt 4 or 5), it is
useful to see what versions are in use. Add an 'About' dialog box that
displays Python, PySide, Qt and database server (SQLite or PostgreSQL)
version numbers.
Committer testing:
$ python ~acme/libexec/perf-core/scripts/python/exported-sql-viewer.py ~/c/adrian.hunter/simple-retpoline.db
Then go to 'Help', then 'About', select all the lines with the mouse
press 'Control+C', then, on the same terminal press control+shift+V
which shows my current environment:
Python version: 2.7.16
PySide version: 1
Qt version: 4.8.7
SQLite version: 3.26.0
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20190503120828.25326-7-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a context menu (right-click) that provides options for copying to
clipboard, including, for trees, the ability to copy only the cell under
the mouse pointer.
Committer testing:
$ python ~acme/libexec/perf-core/scripts/python/exported-sql-viewer.py ~/c/adrian.hunter/simple-retpoline.db
Simply right click and pick "Copy selection", that at this point has
just the first line, not expanded, then see what was copied by pressing
shift+control+v on a terminal:
Call Path,Object,Count,Time (ns),Time (%),Branch Count,Branch Count (%)
▶ simple-retpolin,,,,,,
Ditto after expanding, i.e. the selection continues to be just one
line:
Call Path Object Count Time (ns) Time (%) Branch Count Branch Count (%)
▼ simple-retpolin
Now select all the lines with the mouse and control+shift+v again:
Call Path Object Count Time (ns) Time (%) Branch Count Branch Count (%)
▼ 14503:14503
▼ _start ld-2.28.so 1 156267 100.0 10602 100.0
▶ unknown unknown 1 2276 1.5 1 0.0
▶ _dl_start ld-2.28.so 1 137047 87.7 10088 95.2
▶ _dl_init ld-2.28.so 1 9142 5.9 326 3.1
▼ _start simple-retpoline 1 7457 4.8 182 1.7
▶ unknown unknown 1 805 10.8 1 0.5
▶ __libc_start_main libc-2.28.so 1 6347 85.1 179 98.4
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20190503120828.25326-6-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As preparation for adding support for copying to clipboard, keep track of
what level each item is in tree items.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20190503120828.25326-4-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix the following error if shrink / enlarge font is used with the help
window.
Traceback (most recent call last):
File "tools/perf/scripts/python/exported-sql-viewer.py", line 2791, in ShrinkFont
ShrinkFont(win.view)
AttributeError: 'HelpWindow' object has no attribute 'view'
Committer testing:
Before, matches above output:
$ python ~acme/libexec/perf-core/scripts/python/exported-sql-viewer.py ~/c/adrian.hunter/simple-retpoline.db
Traceback (most recent call last):
File "/home/acme/libexec/perf-core/scripts/python/exported-sql-viewer.py", line 2780, in EnlargeFont
EnlargeFont(win.view)
AttributeError: 'HelpWindow' object has no attribute 'view'
$
After:
No more tracebacks, but the fonts don't get enlarged, which is kinda
frustrating...
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20190503120828.25326-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As preparation for adding support for copying to clipboard, create view
in TreeWindowBase instead of derived classes.
Committer testing:
Tested using an old .db used to test some older patches:
$ python ~acme/libexec/perf-core/scripts/python/exported-sql-viewer.py ~/c/adrian.hunter/simple-retpoline.db
Nothing breaks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20190503120828.25326-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Icelake and later platforms support collecting XMM registers with PEBS
event.
Add support for 'perf script' to dump them, and support for the register
parser in 'perf record -I=' ... to configure them.
For now they are just printed in hex, we could potentially later add
other formats too.
Committer testing:
Before:
# perf record -IXMM0
Warning:
unknown register XMM0, check man page or run 'perf record -I?'
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
#
# perf record -I?
available registers: AX BX CX DX SI DI BP SP IP FLAGS CS SS R8 R9 R10 R11 R12 R13 R14 R15
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
#
After:
# perf record -IXMM0
Error:
The sys_perf_event_open() syscall returned with 22 (Invalid argument) for event (cycles).
/bin/dmesg | grep -i perf may provide additional information.
#
# perf record -I?
available registers: AX BX CX DX SI DI BP SP IP FLAGS CS SS R8 R9 R10 R11 R12 R13 R14 R15 XMM0 XMM1 XMM2 XMM3 XMM4 XMM5 XMM6 XMM7 XMM8 XMM9 XMM10 XMM11 XMM12 XMM13 XMM14 XMM15
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-I, --intr-regs[=<any register>]
sample selected machine registers on interrupt, use -I ? to list register names
#
More work is needed to, when faced with such error, warn the user that
that register is not available on the running platform.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20190506141926.13659-1-kan.liang@linux.intel.com
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add quotes around the register name and suggest using 'perf record -I?'
to get the list of available registers.
Before:
# perf record -Idi,xmm20,xmm1
Warning:
unknown register xmm20, check man page
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-I, --intr-regs[=<any register>]
sample selected machine registers on interrupt, use -I ? to list register names
#
# perf record -Idi,xmm20,xmm1
Warning:
unknown register "xmm20", check man page or run "perf record -I?"
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-I, --intr-regs[=<any register>]
sample selected machine registers on interrupt, use -I ? to list register names
#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lkml.kernel.org/n/tip-9a9hyuum8c0oggg86xd3sxc5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
$ perf record -h -I
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-I, --intr-regs[=<any register>]
sample selected machine registers on interrupt, use -I ? to list register names
$ m
$ perf record -I ?
Workload failed: No such file or directory
$
After:
$ perf record -h -I
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-I, --intr-regs[=<any register>]
sample selected machine registers on interrupt, use '-I?' to list register names
$
$ perf record -I?
available registers: AX BX CX DX SI DI BP SP IP FLAGS CS SS R8 R9 R10 R11 R12 R13 R14 R15
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-I, --intr-regs[=<any register>]
sample selected machine registers on interrupt, use '-I?' to list register names
$
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Fixes: bcc84ec65a ("perf record: Add ability to name registers to record")
Link: https://lkml.kernel.org/n/tip-r0xhfhy5radmkhhcbcfs5izf@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
