This enables CONFIG_THERMAL_OF by default for sunxi_defconfig. It is
required to get Allwinner SoCs' temperature from the GPADC driver.
The Allwinner SoCs all have an ADC that can also act as a touchscreen
controller and a thermal sensor. The first four channels can be used
either for the ADC or the touchscreen and the fifth channel is used for
the thermal sensor.
The thermal sensor requires the IP to be in touchscreen mode to return
correct values. Therefore, if the user is continuously reading the ADC
channel(s), the thermal framework in which the thermal sensor is
registered will switch the IP in touchscreen mode to get a temperature
value and requires a delay of 100ms (because of the mode switching),
then the ADC will switch back to ADC mode and requires also a delay of
100ms. If the ADC readings are critical to user and the SoC temperature
is not, the GPADC driver is capable of not registering the thermal
sensor in the thermal framework and thus, "quicken" the ADC readings. In
most use cases, the SoC temperature is more critical (for cpu throttling
for example or activating cooling devices) than ADC readings, thus it is
now enabled by default.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the new DRM driver in the sunxi default configuration
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner SoCs typically have a Mentor Graphics Inventra MUSB dual role
controller for USB OTG.
Now that the issue with MUSB and USB gadget registration order has been
resolved, we can enable this driver in dual role mode. This requires the
NOP USB transceiver driver, which is also enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sunxi_defconfig already enables INPUT_AXP20X_PEK, but the device is not
exposed to userspace. Enable INPUT_EVDEV so it is.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A consumer IR receiver is commonly found on Allwinner SoC based
development boards and set top boxes. The driver has been available
for some time. Enable it by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As usual, a bunch of commits, mostly adding drivers and other options to
defconfigs because it makes sense to have them enabled on various development
or product boards. Too much to enumerate each here.
There's an introduction of a pxa_defconfig, since PXA finally will allow
building a shared kernel for all boards. With this, we can hopefully
remove a bunch of individual defconfigs down the road but it requires
a bit of real life testing and transition period.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YsCa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC defconfig updates from Olof Johansson:
"As usual, a bunch of commits, mostly adding drivers and other options
to defconfigs because it makes sense to have them enabled on various
development or product boards. Too much to enumerate each here.
There's an introduction of a pxa_defconfig, since PXA finally will
allow building a shared kernel for all boards. With this, we can
hopefully remove a bunch of individual defconfigs down the road but it
requires a bit of real life testing and transition period"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: Add CONFIG_DEPRECATED_PARAM_STRUCT to netwinder_defconfig
ARM: multi_v7_defconfig: Add rockchip audio support
arm: multi_v7_defconfig: Add virtio drivers
ARM: zx_defconfig: remove CONFIG_MMC_DW_IDMAC
ARM: versatile: enable the right LEDs
ARM: pxa: add defconfig covering all the boards
ARM: versatile: select some defaults in defconfig
ARM: multi_v7_defconfig: Enable fan, sensors and audio for Odroid XU3
ARM: bcm2835: enable auxiliary spi driver in defconfig
ARM: bcm2835: enable all bcm2835-relevant in defconfig
ARM: default to multi_v7_defconfig
ARM: multi_v7_defconfig: enable rk808 clkout module
ARM: multi_v7_defconfig: enable rockchip crypto module
ARM: multi_v7_defconfig: enable Rockchip io-domain driver
ARM: multi_v7_defconfig: Enable generic SoC internal OMAP regulators
ARM: multi_v7_defconfig: Enable AM437x PMIC TPS65218
ARM: multi_v7_defconfig: enable TPS65217 regulator
ARM: realview: select apropriate targets
ARM: defconfig: qcom: Enable SSBI drivers
ARM: defconfig: Update qcom_defconfig
...
Commit 69fb4dcada ("power: Add an axp20x-usb-power driver") introduced a new
driver for the USB power supply used on various Allwinner based SBCs. However,
the driver was not added to sunxi_defconfig which breaks USB support for some
boards (e.g. LeMaker BananaPi) as the kernel will now turn off the USB power
supply during boot by default if the driver isn't present. (This was not the
case in linux 4.3 or lower where the USB power was always left on.)
Hence, add the driver to sunxi_defconfig in order to keep USB support working
on those boards that require it.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Reported-by: David Tulloh <david@tulloh.id.au>
Tested-by: David Tulloh <david@tulloh.id.au>
Tested-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Clean up sunxi_defconfig by generating a fresh file via
make sunxi_defconfig
make savedefconfig
While this moves around a few lines and removes unnecessary symbols,
it doesn't introduce any functional changes. The resulting .config is
identical before and after this patch.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit be8becb81b ("ARM: sunxi_defconfig: Enable LRADC keys
(KEYBOARD_SUN4I_LRADC)") added CONFIG_KEYBOARD_SUN4I_LRADC=y to
sunxi_defconfig. However, it depends on CONFIG_KEYBOARD which is
explicitly disabled in sunxi_defconfig. Hence, the LRADC keys were
never actually enabled. Remove the line disabling CONFIG_KEYBOARD in
order to really enable KEYBOARD_SUN4I_LRADC.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit 3d0b16a66c ("nvmem: sunxi: Move the SID driver to the nvmem
framework") moved the the sunxi SID driver to a new framework, but left
sunxi_defconfig with the deprecated config symbol EEPROM_SUNXI_SID
instead of the new symbol NVMEM_SUNXI_SID. Hence, re-enable the driver
in sunxi_defconfig.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
axp20x support has been split into 2 parts, I2C and RSB interface
variants.
Update the MFD_AXP20X symbol for I2C support, and also enable
MFD_AXP20X_RSB to support RSB variants.
Keep MFD_AXP20X enabled for now, to ease migration for automated boot
farms while the patches are being merged. This should be removed in the
next release.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Loadable module support is enabled so we should allow unloading
modules too. This also allows lsmod to show values other than "-2" in
the "Used by" column.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Defconfig sunxi for Allwinner A10/A20 CAN driver
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable sun6i DMA engine, sun6i P2WI, PWM, and crypto engine (Security
System) drivers by default. EXTCON is needed by the updated sun4i USB
PHY driver.
While at it, enable FHANDLE, which is needed by systemd and newer
versions of udev. Also enable CGROUPS for systemd.
And get rid of POWER_RESET, as the sun6i power reset driver has been
removed in favor of proper sun6i watchdog support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have simplefb support, we can enable it in our defconfig. Also
enable the framebuffer console, so that we are sure that we actually get
something displayed in any case.
And while we're at it, enable the module support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit b2b3a8b934 ("power/reset: Remove sun6i reboot driver") removed
the sun6i reboot driver. But sunxi_defconfig and multi_v7_defconfig
still contain the symbol CONFIG_POWER_RESET_SUN6I that was deprecated
by that commit, so remove it.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The a80 optimus has 8 CPUs. I propose we increase the maximum number of CPUs to 8 to avoid the following warning identified during automated boot testing [1].
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ../arch/arm/kernel/devtree.c:144 arm_dt_init_cpu_maps+0x110/0x1e0()
DT /cpu 5 nodes greater than max cores 4, capping them
CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-00528-gbdccc4edeb03 #1
Hardware name: Allwinner sun9i Family
[] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[] (show_stack) from [] (dump_stack+0x74/0x90)
[] (dump_stack) from [] (warn_slowpath_common+0x70/0xac)
[] (warn_slowpath_common) from [] (warn_slowpath_fmt+0x30/0x40)
[] (warn_slowpath_fmt) from [] (arm_dt_init_cpu_maps+0x110/0x1e0)
[] (arm_dt_init_cpu_maps) from [] (setup_arch+0x634/0x8d4)
[] (setup_arch) from [] (start_kernel+0x88/0x3ac)
[] (start_kernel) from [<20008074>] (0x20008074)
---[ end trace cb88537fdc8fa200 ]---
[1] http://storage.kernelci.org/mainline/v3.19-528-gbdccc4edeb03/arm-sunxi_defconfig/lab-tbaker/boot-sun9i-a80-optimus.html
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch enables TOUCHSCREEN_SUN4I, CPUFREQ_DT, and CPU_THERMAL to
enable cpufreq support with passive cpu cooling (thermal throttling)
by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Having switched over all of the users of CONFIG_PM_RUNTIME to use
CONFIG_PM directly, turn the latter into a user-selectable option
and drop the former entirely from the tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
I missed in 9a2ad529ed that REGULATOR_FIXED_VOLTAGE had also gotten
deselected, so it needs to be added back as an explicit option.
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 97a13e5289 ('net: phy: mdio-sun4i: don't select REGULATOR') removed
the select of REGULATOR, which means that it now has to be explicitly
enabled in the defconfig or things won't work very well.
In particular, this fixes a problem with SD/MMC not probing on my A31-based
board.
Cc: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Nothing major, just a few drivers additions and misc options
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+yQb
-----END PGP SIGNATURE-----
Merge tag 'sunxi-defconfig-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/defconfig
Pull "Allwinner defconfig additions for 3.18" from Maxime Ripard
Nothing major, just a few drivers additions and misc options
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'sunxi-defconfig-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi_defconfig: add NLS_CODEPAGE_437 and NLS_ISO8859_1
ARM: sunxi: Add A31 RTC driver to multi_v7_defconfig
ARM: sunxi: Add A31 RTC driver to sunxi_defconfig
The virtual consumer is a test device intended to be used while developing
regulator drivers, it should never be used in production. Remove it from
all defconfigs to avoid confusion among users.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that we have a driver for A31's RTC, enable it
in the default sunxi config.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Update sunxi_defconfig and multi_v7 with all the latest Allwinner
additions.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
this patch drops CONFIG_COMMON_CLK_DEBUG option
as this config option is now obsolete.
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
CC: Olof Johansson <olof@lixom.net>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since the support of the GMAC has been merged, we're using it as the ethernet
controller on the A20 devices.
However, sunxi_defconfig wasn't selecting it hence breaking the NFS boot.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This enables a few more options on the sunxi defconfigs such that I can
use nfsroot to boot them (there is no local storage support yet). It
also enables PRINTK_TIME and tmpfs since it's a common distro requirement.
Signed-off-by: Olof Johansson <olof@lixom.net>
So far, the Allwinner SoCs were only supported using the
multi_v7_defconfig. Add a defconfig of our own to have one a bit more
tailor-made.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
