This mceusb does not need the carrier count quirk, with it set it reports
the carrier higher than it is.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Windows Media Center IR transceivers include two IR receivers;
wide-band/short-range and narrow-band/long-range. The short-range
(5cm distance) receiver is for IR learning and has IR carrier
frequency measuring ability.
Add mceusb driver support to select the short range IR receiver
and enable pass through of its IR carrier frequency measurements.
RC and LIRC already support these mceusb driver additions.
Test platform:
Linux raspberrypi 4.9.59-v7+ #1047 SMP Sun Oct 29 12:19:23 GMT 2017 armv7l GNU/Linux
mceusb 1-1.2:1.0: Registered Pinnacle Systems PCTV Remote USB with mce emulator interface version 1
mceusb 1-1.2:1.0: 2 tx ports (0x0 cabled) and 2 rx sensors (0x1 active)
Sony TV remote control
ir-ctl from v4l-utils
pi@raspberrypi:~ $ ir-ctl -V
IR raw version 1.12.3
pi@raspberrypi:~ $ ir-ctl -m -r
...
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 1200
space 600
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 550
carrier 40004
space 16777215
^C
pi@raspberrypi:~ $ exit
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A timeout of 200ms is much longer than necessary, and delays the decoding
decoding of a single scancode and the last scancode when a button is being
held. This makes the remote seem sluggish.
If the min_timeout and max_timeout values are set, the timeout is
configurable via the LIRC_SET_REC_TIMEOUT ioctl.
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Meson doesn't seem to be able to generate timeout events in hardware. So
install a software timer to generate the timeout events required by the
decoders to prevent "ghost keypresses".
Reported-by: Matthias Reichl <hias@horus.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This renames the protocol for the imon rc driver from other to imon,
since it is now an known protocol. Although different name will show up
in the sysfs protocol file, loading a keymap using existing ir-keytable
versions still works.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This makes it possible to use the various iMON remotes with any raw IR
RC device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If there is IR in the raw kfifo when ir_raw_event_unregister() is called,
then kthread_stop() causes ir_raw_event_thread to be scheduled, decode
some scancodes and re-arm timer_keyup. The timer_keyup then fires when
the rc device is long gone.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These devices were supported by the lirc_imon.c driver which was removed
from staging in commit f41003a23a ("[media] staging: lirc_imon: port
remaining usb ids to imon and remove").
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Note that the stick on the remote is not supported yet.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This code was ported without the necessary hardware to test. There
are multiple problems which are more easily solved by writing a
separate driver.
This reverts commit f41003a23a.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch updates the sunxi-ir driver to set the base clock frequency from
devicetree.
This is necessary since there are different ir receivers on the
market, that operate with different frequencies. So this value could be
set if the attached ir receiver needs a different base clock frequency,
than the default 8 MHz.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a possible race condition between the IR timeout being generated
from the timer, and new IR arriving. This could result in the timeout
being added to the kfifo after new IR arrives. On top of that, there is
concurrent write access to the kfifo from ir_raw_event_store_edge() and
the timer.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit a60d64b15c ("media: lirc: lirc interface should not be
a raw decoder"), the message in the documentation is incorrect as the
module name is rc_core, not lirc_dev. Since the message is not useful,
just make the message debug and remove it from the documentation.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current code gets the start time before copying the IR from
userspace (could cause page faults) and encoding IR. This means
that the gap calculation could be off.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use dev_dbg() rather than custom debug function.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use dev_dbg() rather than custom debug function.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Calculate the pulse rather than having a few preset values.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Return code of clk_prepare_enable() is ignored in many places.
The patch adds error handling for all of them.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I usually update my config with make oldconfig and pressing return,
trusting that whoever updates Kconfig sets sensible defaults.
But my recent kernels ended up with all kinds of IR decoders
built in that are not used by anything because they are all
marked with default y.
default y should only be set for something that prevents
booting on common systems, never for some random weirdo
driver feature like this.
Remove all the "default y" in drivers/media/rc/Kconfig
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=H9AS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- videobuf2 was moved to a media/common dir, as it is now used by the
DVB subsystem too
- Digital TV core memory mapped support interface
- new sensor driver: ov7740
- several improvements at ddbridge driver
- new V4L2 driver: IPU3 CIO2 CSI-2 receiver unit, found on some Intel
SoCs
- new tuner driver: tda18250
- finally got rid of all LIRC staging drivers
- as we don't have old lirc drivers anymore, restruct the lirc device
code
- add support for UVC metadata
- add a new staging driver for NVIDIA Tegra Video Decoder Engine
- DVB kAPI headers moved to include/media
- synchronize the kAPI and uAPI for the DVB subsystem, removing the gap
for non-legacy APIs
- reduce the kAPI gap for V4L2
- lots of other driver enhancements, cleanups, etc.
* tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (407 commits)
media: v4l2-compat-ioctl32.c: make ctrl_is_pointer work for subdevs
media: v4l2-compat-ioctl32.c: refactor compat ioctl32 logic
media: v4l2-compat-ioctl32.c: don't copy back the result for certain errors
media: v4l2-compat-ioctl32.c: drop pr_info for unknown buffer type
media: v4l2-compat-ioctl32.c: copy clip list in put_v4l2_window32
media: v4l2-compat-ioctl32.c: fix ctrl_is_pointer
media: v4l2-compat-ioctl32.c: copy m.userptr in put_v4l2_plane32
media: v4l2-compat-ioctl32.c: avoid sizeof(type)
media: v4l2-compat-ioctl32.c: move 'helper' functions to __get/put_v4l2_format32
media: v4l2-compat-ioctl32.c: fix the indentation
media: v4l2-compat-ioctl32.c: add missing VIDIOC_PREPARE_BUF
media: v4l2-ioctl.c: don't copy back the result for -ENOTTY
media: v4l2-ioctl.c: use check_fmt for enum/g/s/try_fmt
media: vivid: fix module load error when enabling fb and no_error_inj=1
media: dvb_demux: improve debug messages
media: dvb_demux: Better handle discontinuity errors
media: cxusb, dib0700: ignore XC2028_I2C_FLUSH
media: ts2020: avoid integer overflows on 32 bit machines
media: i2c: ov7740: use gpio/consumer.h instead of gpio.h
media: entity: Add a nop variant of media_entity_cleanup
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
The rc5 protocol does not have a leading pulse or space, but we encode
the first bit using a single leading pulse. For other protocols, the
leading pulse or space does not represent any bit. So, don't remove the
first bit if a leading pulse is present.
Cc: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The IR rc6 encoder sends the header using manchester encoding using 0
bits, which causes the following:
UBSAN: Undefined behaviour in drivers/media/rc/rc-ir-raw.c:247:6
shift exponent 4294967295 is too large for 64-bit type 'long long unsigned int'
So, allow the leader code to send a pulse and space and remove the unused
pulse_space_start field.
Cc: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit 9b6192589b ("media: lirc: implement scancode sending"),
and commit de142c3241 ("media: lirc: implement reading scancode")
the lirc features ioctl for raw IR devices advertises two modes for
sending and receiving.
The lirc daemon now fails to detect a raw IR device, both for transmit
and receive.
To fix this, do not advertise the scancode mode in the lirc features
for raw IR devices (however do keep it for scancode devices). The mode
can still be used via the LIRC_SET_{REC,SEND}_MODE ioctl.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit a60d64b15c ("media: lirc: lirc interface should not be
a raw decoder"), there is no lirc_dev module any more. On Ubuntu 16.10,
the /etc/init.d/lirc startup script attempts to load the lirc_dev module.
Since this module does not exist any more, this script fails. Add an alias
so the correct module is loaded.
Fixes: a60d64b15c ("media: lirc: lirc interface should not be a raw decoder")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current error exit path if ir_raw_encode_scancode fails is via the
label out_kfree which kfree's an uninitialized pointer txbuf. Fix this
by exiting via a new exit path that does not kfree txbuf. Also exit
via this new exit path for a failed allocation of txbuf to avoid a
redundant kfree on a NULL pointer (to save a bunch of CPU cycles).
Detected by: CoverityScan, CID#1463070 ("Uninitialized pointer read")
Fixes: f81a8158d4 ("media: lirc: release lock before sleep")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a lot of places where sequences of space/tabs are
found. Get rid of all spaces before tabs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On several places, whitespaces are being used for indentation,
or even at the end of the line.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the original license statement with the SPDX identifier.
Update also the copyright owner adding myself as co-owner of the
copyright.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is no reason to hold the lock while we wait for the IR to transmit.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is code existed for when drivers would send less than the whole
buffer; no driver does this any more, so this is redundant. Drivers
should return -EINVAL if they cannot send the entire buffer.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If memdup_user() fails, txbuf will be an error pointer and passed
to kfree.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The TX loop is more complex than it should. Simplify it.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semantics for lirc IR transmit with raw IR is that the write call
should block until the IR is transmitted. Some drivers have no idea
when this actually is (e.g. mceusb), so there is a wait.
This is useful for userspace, as it might want to send a IR button press,
a gap of a predefined number of milliseconds, and then send a repeat
message.
It turns out that for transmitting scancodes this feature is even more
useful, as user space has no idea how long the IR is. So, maintain
the existing semantics for IR scancode transmit.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit 9c7fd60e951d ("media: rc: Replace timeval with ktime_t in
imon.c"), the function tv2int() is no longer used. Remove it.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Another device with the 0xffdc device id, this one with 0x26 in the
config byte. Its an iMON Inside + iMON IR. It does respond to rc-6,
but seems to produce random garbage rather than a scancode.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The agreed format is to use /* */ comments inside header
files. Unfortunately, I ended by using // on a few ones.
Reported-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CEC autorepeat is different than other protocols. Autorepeat is triggered
by the first repeated user control pressed CEC message, rather than a
fixed REP_DELAY.
This change also does away with the KEY_UP event directly after the first
KEY_DOWN event, which was used to stop autorepeat from starting.
See commit a9a249a2c9 ("media: cec: fix remote control passthrough")
for the original change.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Another device with the 0xffdc device id, this one with 0x30 in the
config byte. Its an iMON VFD + iMON IR (it does not understand rc6).
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The pnp_irq() function returns -1 if an error occurs.
pnp_irq() error checking for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch changes the 32-bit time type (timeval) to the 64-bit one
(ktime_t), since 32-bit time types will break in the year 2038.
I use ktime_t instead of all uses of timeval in imon.c
This patch also changes do_gettimeofday() to ktime_get() accordingly,
since ktime_get returns a ktime_t, but do_gettimeofday returns a
struct timeval, and the other reason is that ktime_get() uses
the monotonic clock.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Once rc_unregister_device() has been called, no driver function
should be called.
This prevents some nasty race conditions with an ioctl calls
driver functions when the driver specific data has been freed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This makes it possible for lircd to read from a lirc chardev, and not
keep it busy.
Note that this changes the default for timeout reports to on. lircd
already enables timeout reports when it opens a lirc device, leaving
them on until the next reboot.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This removes the need for include/media/lirc.h, which just includes
the uapi file.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since removing the lirc kapi, ir-lirc-codec.c only contains lirc fops
so the file name is no longer correct. By moving its content into
lirc_dev.c the ugly extern struct lirc_fops is not longer needed,
and everything lirc related is in one file.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that the lirc interface supports scancodes, RC scancode devices
can also have a lirc device. The only receiving feature they will have
enabled is LIRC_CAN_REC_SCANCODE.
Note that CEC devices have no lirc device, since they can be controlled
from their /dev/cecN chardev.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
