The R40 datasheet specifies a tolerance range for the external
oscillators used. Add them to the device tree as the clock accuracy.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The H3 datasheet specifies a tolerance range for the external
oscillators used. Add them to the device tree as the clock accuracy.
The internal oscillator is left unchanged, as it will be removed later.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The sw2iso count should cover ARM LDO ramp-up time,
the MAX ARM LDO ramp-up time may be up to more than
100us on some boards, this patch sets sw2iso to 0xf
(~384us) which is the reset value, and it is much
more safe to cover different boards, since we have
observed that some customer boards failed with current
setting of 0x2.
Fixes: 05136f0897 ("ARM: imx: support arm power off in cpuidle for i.mx6sx")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the SPI NOR device used to boot up the system
to the iWave RZ/G1N Qseven System On Module DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the backlight device for the LVDS1 output, in preparation for panel
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The iWave RZ/G1N board is almost identical to RZ/G1M. cmt and rwdt modules
are SoC specific and should be part of board dts rather than SoM dtsi. By
moving these nodes to the common dtsi it allows cmt and rwdt to be enabled
on both of these boards with less lines of code.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds nodes for all possible UARTs to sdm845.dtsi. By default
only configure the RX/TX lines with pinctrl. Boards that use UARTs
with flow control can overwrite the configuration in the
<board>.dtsi.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the device node of the GCE hardware for CMDQ module.
Signed-off-by: Houlong Wei <houlong.wei@mediatek.com>
Signed-off-by: HS Liao <hs.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The current oversampling rate of 512 means that for 48 kHz 16 bit
stereo, the MCLK is running at the same rate as the module clock,
so there is no head room to support higher sampling rates. The codec
however supports up to 192 kHz for playback.
This patch drops the oversampling rate from 512 to 128, so that 192 kHz
audio can be played back directly without downsampling. Ideally we
should be using different oversampling rates for different sampling
rates, but that's not possible without a platform-specific machine
driver.
Fixes: 870f1bd1f5 ("ARM: dts: sun8i: Add audio codec, dai and card for A33")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds the Video Engine node for the A64. Since it can map the whole
DRAM range, there is no particular need for a reserved memory node
(unlike platforms preceding the A33).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the description for the SRAM C1 section to the A64 device-tree.
Since there is no entry for this section in the A64 manual, the base
address and size were only verified to be consistent empirically.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Just like on the A33, the video engine on the H3 can map any address in
memory, so there is no particular need to have reserved memory at a fixed
address.
As a result, remove the reserved memory node and let the kernel allocate
the CMA pool wherever it sees fit.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
While we believed that the memory for the video engine had to be kept
in the first 256 MiBs of DRAM, this is no longer true starting with the
A33 and any address can be mapped.
As a result, remove the reserved memory node and let the kernel allocate
the CMA pool wherever it sees fit.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds the Video Engine node for the H5. Since it can map the whole
DRAM range, there is no particular need for a reserved memory node
(unlike platforms preceding the A33).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The EMAC driver requires a syscon node to access the EMAC clock
configuration register (that is part of the system-control register
range and controlled). For this purpose, a dummy syscon node was
introduced to let the driver access the register freely.
Recently, the EMAC driver was tuned to get access to the register when
the SRAM driver is registered (as used on the A64). As a result, it is
no longer necessary to have a dummy syscon node for that purpose.
Now that we have a proper system-control node for both the H3 and H5,
we can get rid of that dummy syscon node and have the EMAC driver use
the node corresponding to the proper SRAM driver (by switching the
syscon label over to each dtsi). This way, we no longer have two
separate nodes for the same register space.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the H5-specific system control node description to its device-tree
with support for the SRAM C1 section, that will be used by the video
codec node later on.
The CPU-side SRAM address was obtained empirically while the size was
taken from the documentation. They may not be entirely accurate.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Unlike in previous generations, the system-control register range is not
limited to a size of 0x30 on the H3. In particular, the EMAC clock
configuration register (accessed through syscon) is at offset 0x30 in
that range.
Extend the register size to its full range (0x1000) as a result.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Wifi chip should be clocked by a 32kHz clock coming from i.MX7D
CLKO2 output pin, so describe the pinmux and clock hierarchy in the
device tree to allow the Wifi chip to be properly clocked.
Managed to successfully test Wifi with such change. Used the standard
nvram.txt file provided by TechNexion, which selects an external 32kHz
clock for the Wifi chip by default.
Fixes: 99a52450c7 ("ARM: dts: imx7d-pico: Add Wifi support")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The values are taken from Amlogic's 3.10 kernel sources.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The values are taken from Amlogic's 3.10 kernel sources. Their sources
have a "meson8m2_n200_2G.dtd" which defines a different voltage table:
- 0.86V for 96MHz
- (values in between omitted)
- 1.14V for 1.992GHz
The reason for this is simply the hardware design because the voltage
regulator on this board is has a minimum output of 0.86V and a maximum
output of 1.14V. The recommended settings are added with this patch
instead of using the values that are only valid for one board.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8b SoC is using four Cortex-A5 cores. These come with an ARM
global timer.
This adds the Cortex-A5 global timer but keeps it disabled for now. The
timer is clocked by the "PERIPH" clock whose rate can change during
runtime (when changing the frequency of the CPU clock). Unfortunately
the arm_global_timer driver does not handle changes to the clock rate
yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8B SoC is using four ARM Cortex-A5 cores which come with a
"TWD" (Timer-Watchdog) based timer. This adds support for the ARM TWD
Timer on this SoC.
Suggested-by: Carlo Caione <carlo@endlessm.com>
[ rebased patch from Carlo, use IRQ_TYPE_EDGE_RISING instead of
IRQ_TYPE_LEVEL_LOW to prevent "GIC: PPI13 is secure or misconfigured"
message during boot, use pre-processor macros to specify the IRQ,
added the correct clock, dropped TWD watchdog node since there's no
driver for it anymore ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8 and Meson8m2 SoCs are using four Cortex-A9 cores. These come
with an ARM global timer.
This adds the Cortex-A9 global timer but keeps it disabled for now. The
timer is clocked by the "PERIPH" clock whose rate can change during
runtime (when changing the frequency of the CPU clock). Unfortunately
the arm_global_timer driver does not handle changes to the clock rate
yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Meson8 and Meson8m2 SoC are using four ARM Cortex-A9 cores which
come with a "TWD" (Timer-Watchdog) based timer. This adds support for
the ARM TWD Timer on these two SoCs.
Suggested-by: Carlo Caione <carlo@endlessm.com>
[ rebased patch from Carlo, use IRQ_TYPE_EDGE_RISING instead of
IRQ_TYPE_LEVEL_LOW to prevent "GIC: PPI13 is secure or misconfigured"
message during boot, use pre-processor macros to specify the IRQ,
added the correct clock, dropped TWD watchdog node since there's no
driver for it anymore ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The public Meson8b (S805) datasheet describes a memory region called "A9
Periph base" which starts at 0xC4300000 and ends at 0xC430FFFF. Add a
simple-bus node and move all peripherals that are part of this memory
region.
This makes the .dts a bit easier to read. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
- Export Meson8b CPU post dividers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Y5Z4
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-headers-4.21-1' of git://github.com/BayLibre/clk-meson into v4.21/dt
Update for meson clocks bindings targeted at v4.21:
- Export Meson8b CPU post dividers
* tag 'meson-clk-headers-4.21-1' of git://github.com/BayLibre/clk-meson:
dt-bindings: clock: meson8b: export the CPU post dividers
Add a device node for the PCIe controller on the Renesas
RZ/G1N (r8a7744) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the xhci controller on the Renesas
RZ/G1N (r8a7744) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DT nodes needed by MSIOF[012] interfaces to the SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the DT node for the QSPI interface to the SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for the camera daughter board which is
connected to iWave's RZ/G1N Qseven carrier board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add TPU support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the definitions for pwm[0123456] to the SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7744 to DT with a disabled
status.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VSP support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VIN[012] support to SoC dt.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CMT[01] support to SoC DT.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch instantiates the thermal sensor module with thermal-zone
support.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the IRQC interrupt controller in the r8a7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the definitions for can0 and can1 to the r8a7744 SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add sound support for the RZ/G1N SoC (a.k.a. R8A7744).
This work is based on similar work done on the R8A7743 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (RWDT) controller on the Renesas
RZ/G1N (r8a7744) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add usb dmac and hsusb device nodes on RZ/G1N SoC dtsi.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe internal PCI bridge devices, USB phy device and
link PCI USB devices to USB phy.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the SDHI0 controller on iWave RZ/G1N Qseven System On Module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add eMMC support for iWave RZ/G1N Qseven System On Module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add MMC node to the DT of the r8a7744 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SDHI nodes to the DT of the r8a7744 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the I2C[0-5] and IIC[0,1,3] devices nodes to the R8A7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIF{|A|B} ports in the R8A7744 device tree.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
