Instead of using the SKB queue with the fake pkt_type for the
offloaded RX BA session management, also handle this with the
normal aggregation state machine worker. This also makes the
use of this more reliable since it gets rid of the allocation
of the fake skb.
Combined with the previous patch, this finally allows us to
get rid of the pkt_type hack entirely, so do that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This brings in commit 7a7c0a6438 ("mac80211: fix TX aggregation
start/stop callback race") to allow the follow-up cleanup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When starting or stopping an aggregation session, one of the steps
is that the driver calls back to mac80211 that the start/stop can
proceed. This is handled by queueing up a fake SKB and processing
it from the normal iface/sdata work. Since this isn't flushed when
disassociating, the following race is possible:
* associate
* start aggregation session
* driver callback
* disassociate
* associate again to the same AP
* callback processing runs, leading to a WARN_ON() that
the TID hadn't requested aggregation
If the second association isn't to the same AP, there would only
be a message printed ("Could not find station: <addr>"), but the
same race could happen.
Fix this by not going the whole detour with a fake SKB etc. but
simply looking up the aggregation session in the driver callback,
marking it with a START_CB/STOP_CB bit and then scheduling the
regular aggregation work that will now process these bits as well.
This also simplifies the code and gets rid of the whole problem
with allocation failures of said skb, which could have left the
session in limbo.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support HT and VHT CSA, beacons and action frames must include the
corresponding IEs.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[make ieee80211_ie_build_wide_bw_cs() return void]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If userspace has flagged support for DFS earlier, then we can follow CSA
to DFS channels. So instead of rejecting the switch, allow it to happen
if the flag has been set during mesh setup.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the Mesh Channel Switch Parameters (8.4.2.105) the reason is specified
to WLAN_REASON_MESH_CHAN_REGULATORY in the case that a regulatory
limitation was the cause for the switch. This means another station
detected a radar event.
Mark the channel as unusable if this happens.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
[sw: style cleanup, rebase]
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parse the BSS max idle period element and set the BSS configuration
accordingly so the driver can use this information to configure the
max idle period and to use protected management frames for keep alive
when required.
The BSS max idle period element is defined in IEEE802.11-2016,
section 9.4.2.79
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.
An example scenario is as below:
In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif
ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
(Reason: 3=DEAUTH_LEAVING)
WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211]
[<bf77272c>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211]))
[<bf73cc50>] (nl80211_new_station [cfg80211])
Unable to handle kernel NULL pointer dereference at virtual
address 00000014
pgd = d5f4c000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
PC is at sta_info_alloc+0x380/0x3fc [mac80211]
LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
[<bf772738>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211])
[<bf73cc50>] (nl80211_new_station [cfg80211]))
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In addition to keeping monitor interfaces on the regular list of
interfaces, keep those that are up and not in cooked mode on a
separate list. This saves having to iterate all interfaces when
delivering to monitor interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Declaring the factor is counter-intuitive, and people are prone
to using small(-ish) values even when that makes no sense.
Change the DECLARE_EWMA() macro to take the fractional precision,
in bits, rather than a factor, and update all users.
While at it, add some more documentation.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
-----BEGIN PGP SIGNATURE-----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=UToW
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
__bitwise__ used to mean "yes, please enable sparse checks
unconditionally", but now that we dropped __CHECK_ENDIAN__
__bitwise is exactly the same.
There aren't many users, replace it by __bitwise everywhere.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Akced-by: Lee Duncan <lduncan@suse.com>
These functions drifts TSF timers, not TBTT.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mesh_sync_offset_adjust_tbtt() implements Extensible synchronization
framework ([1] 13.13.2 Extensible synchronization framework). It shall
not operate the flag "TBTT Adjusting subfield" ([1] 8.4.2.100.8 Mesh
Capability), since it is used only for MBCA ([1] 13.13.4 Mesh beacon
collision avoidance, see 13.13.4.4.3 TBTT scanning and adjustment
procedures for detail). So this patch remove the flag operations.
[1] IEEE Std 802.11 2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[remove adjusting_tbtt entirely, since it's now unused]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ability for an AP (and associated VLANs) to perform
multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own
MAC address rather than the group address.
Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)
This also doesn't implement the 802.11 DMS (directed multicast
service).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[use true/false, rename label to the correct "multicast",
use __be16 for ethertype and network order for constants]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support for encrypting (Re)Association Request frame and
decryption (Re)Association Response frame when using FILS in station
mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The uapsd_queue field is in QoS IE order and not in
IEEE80211_AC_*'s order.
This means that mac80211 would get confused between
BK and BE which is certainly not such a big deal but
needs to be fixed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to IEEE 802.11-2012 section 8.3.2 table 8-19, the outer SA/DA
of A-MSDU frames need to be changed depending on FromDS/ToDS values.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[use ether_addr_copy and add alignment annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds filtering for multicast data packets on AP_VLAN
interfaces that have no authorized station connected and changes
filtering on AP interfaces to not count stations assigned to
AP_VLAN interfaces.
This saves airtime and avoids waking up other stations currently
authorized in this BSS. When using WPA, the packets dropped could
not be decrypted by any station.
The behaviour when there are no AP_VLAN interfaces is left unchanged.
When there are AP_VLAN interfaces, this patch
1. adds filtering multicast data packets sent on AP_VLAN interfaces
that have no authorized station connected.
No filtering happens on 4addr AP_VLAN interfaces.
2. makes filtering of multicast data packets sent on AP interfaces
depend on the number of authorized stations in this bss not
assigned to an AP_VLAN interface.
Therefore, a new num_mcast_sta counter is added for AP_VLAN interfaces.
The existing one for AP interfaces is altered to not track stations
assigned to an AP_VLAN interface.
The new counter is exposed in debugfs.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[reformat commit message a bit, unline ieee80211_vif_{inc,dec}_num_mcast]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Resolve the merge conflict between Felix's/my and Toke's patches
coming into the tree through net and mac80211-next respectively.
Most of Felix's changes go away due to Toke's new infrastructure
work, my patch changes to "goto begin" (the label wasn't there
before) instead of returning NULL so flow control towards drivers
is preserved better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TXQ intermediate queues can cause packet reordering when more than
one flow is active to a single station. Since some of the wifi-specific
packet handling (notably sequence number and encryption handling) is
sensitive to re-ordering, things break if they are applied before the
TXQ.
This splits up the TX handlers and fast_xmit logic into two parts: An
early part and a late part. The former is applied before TXQ enqueue,
and the latter after dequeue. The non-TXQ path just applies both parts
at once.
Because fragments shouldn't be split up or reordered, the fragmentation
handler is run after dequeue. Any fragments are then kept in the TXQ and
on subsequent dequeues they take precedence over dequeueing from the FQ
structure.
This approach avoids having to scatter special cases all over the place
for when TXQ is enabled, at the cost of making the fast_xmit and TX
handler code slightly more complex.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[fix a few code-style nits, make ieee80211_xmit_fast_finish void,
remove a useless txq->sta check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement add/rm_nan_func functions and handle NAN function
termination notifications. Handle instance_id allocation for
NAN functions and implement the reconfig flow.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement nan_change_conf callback which allows to change current
NAN configuration (master preference and dual band operation).
Store the current NAN configuration in sdata, so it can be used
both to provide the driver the updated configuration with changes
and also it will be used in hw reconfig flows in next patches.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 currently uses rhashtable with insecure_elasticity set
to true. The latter is because of duplicate objects. What's
more, mac80211 walks the rhashtable chains by hand which is broken
as rhashtable may contain multiple tables due to resizing or
rehashing.
This patch fixes it by converting it to the newly added rhltable
interface which is designed for use with duplicate objects.
With rhltable a lookup returns a list of objects instead of a
single one. This is then fed into the existing for_each_sta_info
macro.
This patch also deletes the sta_addr_hash function since rhashtable
defaults to jhash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the 'aqm' stats in mac80211 only keeps overlimit drop stats,
not CoDel stats. This moves the CoDel stats into the txqi structure to
keep them per txq in order to show them in debugfs.
In addition, the aqm debugfs output is restructured by splitting it up
into three files: One global per phy, one per netdev and one per
station, in the appropriate directories. The files are all called aqm,
and are only created if the driver supports the wake_tx_queue op (rather
than emitting an error on open as previously).
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add support to MU-MIMO air sniffer according groupID:
in monitor mode, use a given MU-MIMO groupID to monitor stations
that belongs to that group using MU-MIMO.
add support for following a station according to its MAC address
using VHT MU-MIMO sniffer:
the monitors wait until they get an action MU-MIMO notification
frame, then parses it in order to find the groupID that corresponds
to the given MAC address and monitors packets destined to that
groupID using VHT MU-MIMO.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Insert the u32 monitor flags variable in a new structure
that represents a monitor interface.
This will allow to add more configuration variables to
that structure which will happen in an upcoming change.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no other limit other than a global
packet count limit when using software queuing.
This means a single flow queue can grow insanely
long. This is particularly bad for TCP congestion
algorithms which requires a little more
sophisticated frame dropping scheme than a mere
headdrop on limit overflow.
Hence apply (a slighly modified, to fit the knobs)
CoDel5 on flow queues. This improves TCP
convergence and stability when combined with
wireless driver which keeps its own tx queue/fifo
at a minimum fill level for given link conditions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211's software queues were designed to work
very closely with device tx queues. They are
required to make use of 802.11 packet aggregation
easily and efficiently.
Due to the way 802.11 aggregation is designed it
only makes sense to keep fair queuing as close to
hardware as possible to reduce induced latency and
inertia and provide the best flow responsiveness.
This change doesn't translate directly to
immediate and significant gains. End result
depends on driver's induced latency. Best results
can be achieved if driver keeps its own tx
queue/fifo fill level to a minimum.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Qdiscs are designed with no regard to 802.11
aggregation requirements and hand out
packet-by-packet with no guarantee they are
destined to the same tid. This does more bad than
good no matter how fairly a given qdisc may behave
on an ethernet interface.
Software queuing used per-AC netdev subqueue
congestion control whenever a global AC limit was
hit. This meant in practice a single station or
tid queue could starve others rather easily. This
could resonate with qdiscs in a bad way or could
just end up with poor aggregation performance.
Increasing the AC limit would increase induced
latency which is also bad.
Disabling qdiscs by default and performing
taildrop instead of netdev subqueue congestion
control on the other hand makes it possible for
tid queues to fill up "in the meantime" while
preventing stations starving each other.
This increases aggregation opportunities and
should allow software queuing based drivers
achieve better performance by utilizing airtime
more efficiently with big aggregates.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Requires software tx queueing and fast-xmit support. For good
performance, drivers need frag_list support as well. This avoids the
need for copying data of aggregated frames. Running without it is only
supported for debugging purposes.
To avoid performance and packet size issues, the rate control module or
driver needs to limit the maximum A-MSDU size by setting
max_rc_amsdu_len in struct ieee80211_sta.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix locking issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regular RX path has a lot of code, but with a few
assumptions on the hardware it's possible to reduce the
amount of code significantly. Currently the assumptions
on the driver are the following:
* hardware/driver reordering buffer (if supporting aggregation)
* hardware/driver decryption & PN checking (if using encryption)
* hardware/driver did de-duplication
* hardware/driver did A-MSDU deaggregation
* AP_LINK_PS is used (in AP mode)
* no client powersave handling in mac80211 (in client mode)
of which some are actually checked per packet:
* de-duplication
* PN checking
* decryption
and additionally packets must
* not be A-MSDU (have been deaggregated by driver/device)
* be data packets
* not be fragmented
* be unicast
* have RFC 1042 header
Additionally dynamically we assume:
* no encryption or CCMP/GCMP, TKIP/WEP/other not allowed
* station must be authorized
* 4-addr format not enabled
Some data needed for the RX path is cached in a new per-station
"fast_rx" structure, so that we only need to look at this and
the packet, no other memory when processing packets on the fast
RX path.
After doing the above per-packet checks, the data path collapses
down to a pretty simple conversion function taking advantage of
the data cached in the small fast_rx struct.
This should speed up the RX processing, and will make it easier
to reason about parallelizing RX (for which statistics will need
to be per-CPU still.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the time since the mesh path table was implemented as an
RCU-traversable, dynamically growing hash table, a generic RCU
hashtable implementation was added to the kernel.
Switch the mesh path table over to rhashtable to remove some code
and also gain some features like automatic shrinking.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh path and mesh gate hashtables are global, containing
all of the mpaths for every mesh interface, but the paths are
all tied logically to a single interface. The common case is
just a single mesh interface, so optimize for that by moving
the global hashtable into the per-interface struct.
Doing so allows us to drop sdata pointer comparisons inside
the lookups and also saves a few bytes of BSS and data.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous approach simply ignored chandef restrictions when calculating
the appropriate peer BW for a WIDER_BW peer. This could result in a
regulatory violation if both peers indicated 80MHz support, but the
regdomain forbade it.
Change the approach to setting a WIDER_BW peer's BW. Don't exempt it from
the chandef width at first. If during TDLS negotiation the chandef width
is upgraded, update the peer's BW to match.
Fixes: 0fabfaafec ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may need to track which vif is using VHT MU-MIMO.
Move the flag indicationg the ownership of MU_MIMO to
ieee80211_vif.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up ieee80211_rx_reorder_ready() callers by passing the RX
TID struct and the index, instead of the frames list. This will
make it more extensible as well.
While at it, move the inline to rx.c as it's only used there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow drivers to make more educated
decisions whether to defer transmission or not.
Relying on wake_tx_queue() call count implicitly
was not possible because it could be called
without queued frame count actually changing on
software tx aggregation start/stop code paths.
It was also not possible to know how long
byte-wise queue was without dequeueing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The timestamp given by iwlwifi is at the beginning of the
frame over the air, at (or during) the SYNC field. Allow
such timestamps to be given to mac80211, at least (for now)
for frames with non-HT/VHT preambles.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The station MLME and IBSS/mesh ones use entirely different
code for interpreting HT and VHT operation elements. Change
the code that interprets them a bit - it now modifies an
existing chandef - and use it also in the MLME code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Group ID Management frame is an Action frame of
category VHT. It is transmitted by the AP to assign
or change the user position of a STA for one or more
group IDs.
Process and save the group membership data. Notify
underlying driver of changes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
An AP can send an operating channel width change in a beacon
opmode notification IE as long as there's a change in the nss as
well (See 802.11ac-2013 section 10.41).
So don't limit updating to nss only from an opmode notification IE.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
