The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: Mikhail Khelik <mkhelik@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7604 supports four digital input ports. This patch adds support
for all of them, instead of just port A.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ignore EDID's where the header is wrong.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Whenever the hotplug pin is pulled low the chip resets a whole bunch
of registers. It turns out that this can be turned off on the adv7511.
Do so, as this 'feature' introduces race conditions in setting up
registers, particular when the hotplug pin bounces a lot.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Retry setup if the device is powered off when it should be powered on. This
state can be caused by rapid hotplug toggles.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Removed dependency on rx-sense interrupt, it's a leftover from obsolete
code. Removing this simplifies the code.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ignore EDIDs where the header is wrong.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
A few devices (em2860) use a separate interface for audio only
Audio Vendor Class USB. That interface should not be used by
Remote Controller, Analog TV or Digital TV.
Prevents initializing all non-audio extensions for the audio
only interface.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the same module version on all em28xx sub-modules, and use
the same naming convention to describe the driver.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Better to split chipset detection from the audio setup. So, move the
detection code to em28xx_init_dev().
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a message with consistent prints before and after each
extension initialization, and provide a better text for module
load.
While here, add a missing sanity check for extension finish
code at em28xx-v4l extension.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that all analog-specific code are at em28xx-video, convert
it into an em28xx extension and load it as a separate module.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix the error handling logic, making it to unregister i2c bus 0, in
case of a failure to register the second bus.
Reported-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several init code inside em28xx-cards that are actually
part of analog initialization. Move the code to em28x-video, in
order to remove part of the mess.
In thesis, no functional changes so far.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When em28xx extensions are loaded/removed, there are two locks:
a single static em28xx_devlist_mutex that registers each extension
and the struct em28xx dev->lock.
When extensions are registered, em28xx_devlist_mutex is taken first,
and then dev->lock.
Be sure that, when extensions are being removed, the same order
will be used.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to make easier for the next patches, do some
cosmetic changes.
No functional changes.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that we want to split the video handling to a separate
module, move all video-specific functions to em28xx-video.
No functional changes.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This macro is not used. remove it.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using two I2C operations between write and read,
use just one i2c_transfer. That allows I2C mutexes to not
let any other I2C transfer between the two.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The spin_lock_irqsave() macro is not nestable. The second call will
overwrite the first record of "flags" so the IRQs will not be enabled
correctly at the end of the function.
In the current code, this function is always called from the IRQ handler
so everything works fine and this fix doesn't change anything.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Smatch complains here because name is a 32 character buffer and we
adding the "OMAP4 ISS " prefix as well for a total of 42 characters.
The sd->name buffer can only hold 32 characters. I've changed it to use
snprintf() to silence the overflow warning.
Also I have removed the call to strlcpy() which is a no-op.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now when the sub-drivers are fixed to work with runtime PM disabled
this erroneous dependency can be removed.
The CAM and ISP power domains should be left in active state by the
platform if runtime PM is not used.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ensure the device works also when runtime PM is disabled. This will
allow to drop an incorrect dependency on PM_RUNTIME.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The memory allocator is being initialized before registering the subdevs
so reverse the cleanup sequence to avoid trying unregister not registered
subdevs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ensure the device also works when runtime PM is disabled.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Devices should also operate normally when runtime PM is not enabled.
In case runtime PM is disabled activate the device already in probe().
Any related power domain needs to be then left permanently in active
state by the platform.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver should ensure a device can be also used normally when runtime
PM is disabled. So enable the FIMC clock in probe() in such situation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver for Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with
embedded SoC ISP. The device is exposed as two V4L2 subdevices:
- S5K5BAF-CIS - the image sensor matrix, fixed 1600x1200 format,
no controls.
- S5K5BAF-ISP - the Image Signal Processor, formats up to 1600x1200,
pre/post ISP cropping, downscaling via selection API, controls.
[m.chehab@samsung.com: Whitespace cleanups]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by the kbuild test robot <fengguang.wu@intel.com>:
> warning: (VIDEO_EM28XX_DVB) selects DVB_M88DS3103 which has unmet direct dependencies (MEDIA_SUPPORT && DVB_CORE && I2C && I2C_MUX)
> drivers/built-in.o: In function `m88ds3103_release':
> >> m88ds3103.c:(.text+0x1ab1af): undefined reference to `i2c_del_mux_adapter'
> drivers/built-in.o: In function `m88ds3103_attach':
> >> (.text+0x1ab342): undefined reference to `i2c_add_mux_adapter'
There are 3 possible ways to fix it:
1) make em28xx dependent on I2C_MUX.
That sounds wrong, as the em28xx bridge doesn't have i2c muxes on it,
and just one frontend has.
Well, subdevs could eventually be converted to, instead of using dvb
i2c gate control, to use i2c mux support.
That makes sense, but it takes time and lots of effort. Not sure if
this will happen anytime soon.
2) MEDIA_SUBDRV_AUTOSELECT can be dependent of I2C and I2C_MUX.
That means that users will need to manually enable I2C_MUX on some
distributions. Not sure about others, but, on Fedora, this option is
disabled.
So, it can end by generating a number of complains from users
that their devices suddenly stopped working after a Kernel upgrade,
at least until all distros that ship Kernels with I2C_MUX enabled.
3) if MEDIA_SUBDRV_AUTOSELECT is selected, it will select I2C and I2C_MUX.
Of course, MEDIA_SUBDRV_AUTOSELECT will need to inherit all dependencies
that I2C and I2C_MUX have (only HAS_IOMEM).
The disadvantage is that, if new dependencies are added on I2C, they'll
also need to be added here.
As the hole idea of autoselect is to let the user not bother about whatever
frontend/tuner is used by a driver, IMHO, (3) is the better solution.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PLL was attached twice to frontend0 leaving frontend1 without a tuner.
frontend0 is DVB-C and frontend1 is DVB-T.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For GPI-connected buttons without (hardware) debouncing, the polling interval
needs to be reduced to detect button presses properly.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The omap24xx driver and the tcm825x sensor driver are the only two
remaining drivers to still use the old deprecated v4l2-int-device API.
Nobody maintains these drivers anymore. But unfortunately the v4l2-int-device
API is used by out-of-tree drivers (MXC platform). This is a very bad situation
since as long as this deprecated API stays in the kernel there is no reason for
those out-of-tree drivers to convert.
This patch moves v4l2-int-device and the two drivers that depend on it to
staging in preparation for their removal.
If someone would be interested in getting these drivers to work, then start with
this since it's not very far from the state where they used to work:
<URL:http://vihersipuli.retiisi.org.uk/cgi-bin/gitweb.cgi?p=~sailus/linux-omap/.git;a=summary>
The branch is n800-cam. Porting to up-to-date APIs can then be done. David
might have done some work in that area, so check with him first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: David Cohen <dacohen@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
During the last media summit meeting it was decided to move this driver to
staging as the first step to removing it altogether.
Most webcams covered by this driver are now supported by gspca. Nobody has the
hardware to convert the remaining devices to gspca.
This driver needs a major overhaul to have it conform to the latest frameworks
and compliancy tests.
Without hardware, however, this is next to impossible. Given the fact that
this driver seems to be pretty much unused (it has been removed from Fedora
several versions ago and nobody complained about that), we decided to drop
this driver.
This patch moves it to staging. Some time in 2014 we will drop it completely.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by kbuild test robot <fengguang.wu@intel.com>:
with a random config:
drivers/built-in.o: In function `dib8000_get_time_us.isra.16':
>> dib8000.c:(.text+0x3075aa): undefined reference to `__udivdi3'
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
GIT_AUTHOR_DATE=1386943312
Add USB IDs for the WinFast DTV Dongle Mini.
Device is tested and works fine under MythTV
Signed-off-by: Robert Backhaus <robbak@robbak.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Latest checkpatch.pl has some new requirements for coding style.
Fix some of those.
* remove Free Software Foundation postal address
* use sizeof(*foo), not sizeof(struct foo)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* remove Free Software Foundation postal address
* add one pair of parenthesis
* use sizeof(*foo), not sizeof(struct foo)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adapter is locked by I2C core already. Use unlocked i2c_transfer()
version __i2c_transfer() to avoid deadlock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert driver from proprietary DVB driver model to standard I2C
driver model.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Write inittab using reg address auto-increment in order to reduce
I/O a little bit.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reg 0x56 should be programmed to 0x01. Add default to inittab.
Reported-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Optimal AGC is highly depended on used RF tuner and due to that
it is already included to chip configuration. However, inittab
has default AGC value, which was later replaced by one from config.
Add also comment to all chip configuration options about default
values and if those are needed to set or not.
Reported-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Used synthesizer is very typical integer-N PLL, with configurable
reference frequency divider, output frequency divider and of
course N itself. Most common method to calculate values is first
select output divider, then calculate VCO frequency and finally
calculate PLL N from VCO frequency. Do it that way.
Also make some cleanups for filter logic and signal strength.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
