Keyboard driver for GPIO buttons(gpio-keys) checks for the legacy
"gpio-key,wakeup" boolean property to enable gpio buttons as wakeup
source.
Few dts files assign value "1" to gpio-key,wakeup and in one instance a
value "0" is assigned probably assuming it won't be enabled as a wakeup
source. Since the presence of the boolean property indicates it is
enabled, value of "0" have no value.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property which inturn fixes the above mentioned issue.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add tuning clk for emmc and sdmmc, otherwise I get
the following failure while enabling mmc-hs200-1_8v.
dwmmc_rockchip ff0f0000.dwmmc: Tuning clock (sample_clk) not defined.
mmc0: tuning execution failed
mmc0: error -5 whilst initialising MMC card
With it
dwmmc_rockchip ff0f0000.dwmmc: Successfully tuned phase to 170
mmc0: new HS200 MMC card at address 0001
mmcblk0: mmc0:0001 M8G1GC 7.28 GiB
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There is a need of a broadcast timer in this case to ensure proper
wakeup when the cpus are in sleep mode and a timer expires.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The card detect pin is currently called sdmcc-cd.
This patch fixes the typo and renames the pin to sdmmc-cd.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In general, the logic voltage is affected by ddr frequency factors.
We should fix the correct voltage range since assuemd that we have the
ddr frequency driver in mainline.
AFAIK, the 1.8v voltage is used by the SD3.0 card.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This board is similar with the rk3288 evb board but the rk3368 top
board. There exist the act8846 as the pmic.
Moment, add the balight/thermal/emmc/usb.. stuff,
Let the board can happy work.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pulse-width modulator (PWM) feature is very common in
embedded systems. On the rk3368 there exist 4 built-in PWM channels.
In general, the pwm pins can via the pinctrl to
configure iomux mode except the pwm2 since the pwm2 iomux mode from
the SoC control register.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch enable the TS-ADC.
When a thermal temperature is invoked use the CRU to reset the chip
on R88 board. TSHUT is low active on this board.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch add the thermal needed info on RK3368.
Meanwhile, support the trips to throttle for thermal.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patchset add the thermal for RK3368 dts,
Since the two CPU clusters, with four CPU core for each cluster,
one cluster is optimized for high-performance(big cluster) and the othe
is optimized for low power(little cluster).
This patch adds the second order for thermal throttle, and the critical
temperature for thermal over-tempeature protection on Software.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add an ethernet0 alias for the RK3368 mac interface so
that u-boot can find the device-node and fill in the mac address on
boards that support a wired network interface.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The idle-states bindings mandate that the entry-method string
in the idle-states node must be "psci" for ARM v8 64-bit systems,
but the examples in the bindings report a wrong entry-method string.
Owing to this typo, some dts in the kernel wrongly defined the
entry-method property, since they likely cut and pasted the example
definition without paying attention to the bindings definitions.
This patch fixes the typo in the DT idle states bindings examples and
respective dts in the kernel so that the bindings and related dts
files are made compliant.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Howard Chen <howard.chen@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
In terms of peripherals the rk3368 is quite similar to the rk3288, which
makes it possible to have a lot basic components working in the first go.
More to follow once I tracked down all the tiny differences that still
exist in some parts.
With these dts files, the R88 board is able to boot from an attached
usb device and most likely from its emmc too, if the emmc uses a standard
partition table instead of Rockchip's own one - the emmc itself is
detected correctly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
