The urb_dequeue() method forgets to unlink 'struct musb_qh' from the
control or bulk schedules when the URB being cancelled is the only
one queued to its endpoint. That will cause musb_advance_schedule()
to block once it reaches 'struct musb_qh' with now empty URB list, so
URBs queued for other endpoints after the one being dequeued will not
be served.
Fix by unlinking the QH from the list except when it's already being
handled (typically by musb_giveback). Since a QH with an empty URB
list is now supposed to be freed, do that. And remove a now-useless
check from musb_advance_schedule().
[ dbrownell@users.sourceforge.net: update patch description,
and fold in a dequeue() comment patch ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The input queue should be used for TX on endpoints which
share FIFO hardware. The host TX path wasn't doing that.
Shared FIFOs are most often configured for periodic endpoints,
which are mostly used for RX/IN transfers ... that's probably
how this bug managed to linger for a long time.
[ dbrownell@users.sourceforge.net: update patch description ]
Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
request->actual is an unsigned and we should use the same
variable type for fifo_count otherwise we might lose some
data if request->length >= 64kbytes.
[ dbrownell@users.sourceforge.net: fix compiler warning ]
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:
- Use clk_enable()/clk_disable() ... the "always enable USB clocks"
code this originally relied on has since been removed.
- Initialize the USB device only after the relevant I2C GPIOs are
available, so the host side can properly enable VBUS.
- Tweak init sequencing to cope with mainline's relatively late init
of the I2C system bus for power switches, transceivers, and so on.
Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested. Also
verified on OMAP3.
(Unrelated: correct the MODULE_PARM_DESC spelling of musb_debug.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies. This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initializes the actual_len field to 0 before every DMA transaction.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These compilation errors are related to incorrect
debugging macro and variable names and generated the
following errors:
drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined
drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment':
drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function)
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h:
No such file or directory
drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h:
No such file or directory
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes insert module failure as free_irq() was not
done in previous rmmod.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trying once more to get this merged. The original was submitted
for 2.6.27-rc2 or so, and never got correctly merged. Neither
were any of the numerous subsequent resends. Sigh.
CC drivers/usb/musb/davinci.o
drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory
drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory
drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory
drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode'
drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some config registers are not avaiable in Blackfin, we have to comment them out.
v1-v2:
- remove Blackfin specific header file
- add Blackfin register version to musb_regs.h header file
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- DMA registers in Blackfin have different layout
- DMA interrupt flags need to be cleared by software
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure we program the correct values in only when necessary.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- replace MUSB_FIFOSIZE register to MUSB_TXCOUNT, cause no MUSB_FIFOSIZE
register on Blackfin
- use #ifdef to replace #if defined()
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without it, in platforms that don't provide irq_chip.set_wake(),
like omap, musb will WARN() on driver removal.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Random host-side MUSB updates, mostly relating to better diagnostics:
+ Improve diagnostics on host side:
- tx flush fifo:
* Avoid hundreds of duplicate TX FIFONOTEMPTY messages
* make "Can't flush TX fifo" a warning, and say which endpoint
- giveback:
* use correct status code
* show completion function name not just URB pointer
- Fix annoying "1 bytes" (should be "1 byte")
+ Be more consistent about failing init of unusable fifo_mode
It's not clear why that "can't flush TX fifo" message appears, though
it might relate to disconnection; I see it not infrequently
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor locking fix for musb_hdrc on OMAP3 and OMAP2430:
don't read DEVCTL without holding the spinlock, since
an IRQ could come in and corrupt things.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix three omissions in the "mode" sysfs attribute support:
(a) inability to report errors;
(b) no DaVinci support ... just report an error;
(c) for omap2430, accepting unsupportable values
The 2430 stuff is still odd....
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This bug was introduced recently. Fix it before bigger
problems appear.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes co-working issue of usb serial device with usb/net devices while
oter endpoints are free and can be used.This patch implements the policy
that if endpoint resources are available then different BULK request goes
to different endpoint otherwise they are multiplexed to one reserved
endpoint as currently done.
Switch statement case is reordered in musb_giveback() to take care of
bulk request both in multiplex scenario and otherwise.
NAK limit scheme has to be added for multiplexed BULK request scenario
to avoid endpoint starvation due to usb/net devices.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order to avoid namespace conflicts, add a prefix
to our kernel-wise symbol.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes blurred capture images in dma mode. Isochronous error field in
urb and source data buffer pointer were not updated properly in dma
mode.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When removing the procfs file, I forgot to remove some
code that created and removed that file. Here's a patch
to fix it. Ideally this patch will be melded into the patch
removing the procfs file, don't know if it's possible still.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Basically getting rid of CaMeLcAsE, but also adding
missing lines and spaces.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor musb_hdrc updates:
- so it'll build on DaVinci, given relevant platform updates;
* remove support for an un-shipped OTG prototype
* rely on gpiolib framework conversion for the I2C GPIOs
* the <asm/arch/hdrc_cnf.h> mechanism has been removed
- catch comments up to the recent removal of the per-SOC header
with the silicon configuration data;
- and remove two inappropriate "inline" declarations which
just bloat host side code.
There are still some more <asm/arch/XYZ.h> ==> <mach/XYZ.h>
changes needed in this driver, catching up to the relocation
of most of the include/asm-arm/arch-* contents.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org> [2.6.27]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes kernel panic while ISO IN transfer is aborted.Replaced
usb_hcd_unlink_urb_from_ep() from musb_giveback() to __musb_giveback()
to make sure urb is unlinked before giveback when __musb_giveback() is
called from musb_urb_dequeue().
Acquired musb->lock() before usb_hcd_unlink_urb_from_ep() within in
enqueue path.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes enumeration failures when a USB device attached to a LS hub is
connected to OMAP EVM via HS hub. This is fixed by correctly
programming hub address register in enqueue path.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For those archs which don't provide read/write friends we
provide our own implementation so musb driver won't break
compilation.
This is temporary fix until a better solution comes from
upstream. Idealy, <linux/io.h> would provide those calls
if the architecture did not provide them yet. In that case
being possible to remove all those stubs from musb_io.h
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no check if platform code passes in more endpoints (num_eps)
than the maximum number of enpoints (MUSB_C_NUM_EPS.) The result is
that allocate_instance() happily writes past the end of 'struct musb'
corrupting memory.
This patch adds a BUG() if the platform code requests more than the max.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In file included from drivers/usb/musb/musb_core.h:59,
from drivers/usb/musb/musb_core.c:108:
drivers/usb/musb/musb_io.h:42: error: conflicting types for '__raw_readsl'
/usr/src/devel/arch/sh/include/asm/io.h:112: error: previous declaration of '__raw_readsl' was here
drivers/usb/musb/musb_io.h:42: error: conflicting types for '__raw_readsl'
/usr/src/devel/arch/sh/include/asm/io.h:112: error: previous declaration of '__raw_readsl' was here
drivers/usb/musb/musb_io.h:44: error: conflicting types for 'readsw'
/usr/src/devel/arch/sh/include/asm/io.h:164: error: previous definition of 'readsw' was here
drivers/usb/musb/musb_io.h:46: error: conflicting types for 'readsb'
/usr/src/devel/arch/sh/include/asm/io.h:163: error: previous definition of 'readsb' was here
drivers/usb/musb/musb_io.h:49: error: conflicting types for '__raw_writesl'
/usr/src/devel/arch/sh/include/asm/io.h:111: error: previous declaration of '__raw_writesl' was here
drivers/usb/musb/musb_io.h:49: error: conflicting types for '__raw_writesl'
/usr/src/devel/arch/sh/include/asm/io.h:111: error: previous declaration of '__raw_writesl' was here
drivers/usb/musb/musb_io.h:51: error: conflicting types for 'writesw'
/usr/src/devel/arch/sh/include/asm/io.h:164: error: previous definition of 'writesw' was here
drivers/usb/musb/musb_io.h:53: error: conflicting types for 'writesb'
/usr/src/devel/arch/sh/include/asm/io.h:163: error: previous definition of 'writesb' was here
Cc: Karsten Keil <kkeil@suse.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If Indexed Mode register accesses are enabled, the ep0_rxstate()
function calls musb_g_ep0_giveback() before writing to the CSR
register. When control returns to this ep0_rxstate, the index
register contents are over-written. This causes the CSR register
write to fail.
Fixed by writing the correct value into the index register before
writing to the CSR.
This was observed only in ep0_rxstate() with g_ether loaded and
the device connected to a MS Windows host PC. Anticipatively fixed
ep0_txstate() as well.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can change debugging level on the fly via
/sys/module/musb_hdrc/parameters/debug.
We can also get rid of the LOGLEVEL facility in Kconfig
and rely only in module parameter.
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers should not add procfs. The functionality in the old
procfs file will be moved to debugfs.
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use platform_data to pass musb configuration-specific
details to musb driver.
This patch will prevent that other platforms selecting
HAVE_CLK and enabling musb won't break tree building.
The other parts of it will come when linux-omap merge
up more omap2/3 board-files.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we try to modprobe a second gadget driver before
rmmoding the first one, the reference for the first
gadget driver would get NULLed avoiding usb to change
gadget drivers later.
Cc: David Brownell <david-b@pacbell.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
