The driver forgets to call i2c_unregister_device in remove like what is
done in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The AVerMedia CE310B is a simple composite + S-Video + stereo audio
capture card, and uses only the CX23888 to perform all of these
functions.
I've tested both video inputs and the audio interface and confirmed that
they're all working. However, there are some issues:
* Sometimes when I switch inputs the video signal turns black and can't
be recovered until the system is rebooted. I haven't been able to
determine the cause of this behavior, nor have I found a solution to
fix it or any workarounds other than rebooting.
* The card sometimes seems to have trouble syncing to the video signal,
and some of the VBI data appears as noise at the top of the frame, but
I assume that to be a result of my very noisy RF environment and the
card's unshielded input traces rather than a configuration issue.
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver misses destroying wdt_wq when remove like what is done when
probe fails.
Add the missed calls like what is done to job_wq to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver forgets to call destroy_workqueue when remove and probe fails.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enclose multiple macro parameters in parentheses in order to
make such macros safer and fix the Clang warning below:
drivers/media/i2c/adv748x/adv748x-afe.c:452:12: warning: operator '?:'
has lower precedence than '|'; '|' will be evaluated first
[-Wbitwise-conditional-parentheses]
ret = sdp_clrset(state, ADV748X_SDP_FRP, ADV748X_SDP_FRP_MASK, enable
? ctrl->val - 1 : 0);
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The periodic PING command could interfere with the result of
a CEC transmit, causing a lost cec_transmit_attempt_done()
call.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently wait_event_interruptible_timeout is called in cec_thread_func()
when adap->transmitting is set. But if the adapter is unconfigured
while transmitting, then adap->transmitting is set to NULL. But the
hardware is still actually transmitting the message, and that's
indicated by adap->transmit_in_progress and we should wait until that
is finished or times out before transmitting new messages.
As the original commit says: adap->transmitting is the userspace view,
adap->transmit_in_progress reflects the hardware state.
However, if adap->transmitting is NULL and adap->transmit_in_progress
is true, then wait_event_interruptible is called (no timeout), which
can get stuck indefinitely if the CEC driver is flaky and never marks
the transmit-in-progress as 'done'.
So test against transmit_in_progress when deciding whether to use
the timeout variant or not, instead of testing against adap->transmitting.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 32804fcb61 ("media: cec: keep track of outstanding transmits")
Cc: <stable@vger.kernel.org> # for v4.19 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
WARN if transmit_queue_sz is 0 but do not decrement it.
The CEC adapter will become unresponsive if it goes below
0 since then it thinks there are 4 billion messages in the
queue.
Obviously this should not happen, but a driver bug could
cause this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v4.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some messages are allowed to be a broadcast message in CEC 2.0
only, and should be ignored by CEC 1.4 devices.
Unfortunately, the check was wrong, causing such messages to be
marked as invalid under CEC 2.0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pat.h is a file whose main purpose is to provide the memtype_*() APIs.
PAT is the low level hardware mechanism - but the high level abstraction
is memtype.
So name the header <memtype.h> as well - this goes hand in hand with memtype.c
and memtype_interval.c.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
Make sure that both enum_mbus_code() and enum_framesize() properly
populate the .which parameter member, otherwise -EINVAL is return
causing the subdev asynchronous registration handshake to fail.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When start_streaming fails after the buffers have been queued we have to
make sure all buffers are returned to user-space properly otherwise a
v4l2 level WARN is generated.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently we were using an arbitrarily small maximum resolution mostly
based on available sensor capabilities. However the hardware DMA limits
are much higher than the statically define maximum resolution we were
using.
There we rework the boundary check code to handle the maximum width and
height based on the maximum line width in bytes and re-calculating the
pixel width based on the given pixel format.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Because V4L2 still uses a specific way to manage power state of devices
that predates runtime PM, bridge driver should power on and off sub
device explicitly.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the needed control module register bit layout to support the AM654
family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the needed control module register bit layout to support
the DRA76x family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current CSI2 DPHY initialization sequence although
functional does not match with the documented sequence
in the Technical Reference Manual.
This may affect capture re-startability in stop/start
situations.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pixel processing unit was hard coded to only handle 8 bits per pixel
from input to output.
We now add handling for 10, 12 and 16 bits per pixel at the source and
setting the in-memory size (i.e. container size) to 16 bits for these 3
cases.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The current method to calculate the ddr clk period is wrong.
Therefore the ths_term calculation is incorrect.
Also it was wrongly assumed that the ths_settle parameter
was based on the control clock instead of the pixel clock.
Since the DPHY can tolerate quite a bit a of variation,
capture was still mostly working with the 2 tested modes
when the pixel clock was close to the control clock
(i.e. 96 Mhz). But it would quickly stops working when
using different modes or when customers used different
sensors altogether.
Calculating the DDRClk period needs to take into account
the pixel bit width and the number of active data lanes.
Based on the latest technical reference manual these
parameters should now be calculated as follows:
THS_TERM: Programmed value = floor(20 ns/DDRClk period)
THS_SETTLE: Programmed value = floor(105 ns/DDRClk period) + 4
Also originally 'depth' was used to represent the number of
bits a pixel would use once stored in memory (i.e. the
container size). To accurately calculate the THS_* parameters
we need to use the actual number of bits per pixels coming
in from the sensor. So we are renaming 'depth' to 'bpp' (bits
per pixels) and update the format table to show the actual
number of bits per pixel being received.
The "container" size will be derived from the "bpp" value.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Apply Errata i913 every time the functional clock is enabled.
This should take care of suspend/resume case as well.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When setting DMA for video capture from CSI channel, if the DMA size
is not given, it ends up writing as much data as sent by the camera.
This may lead to overwriting the buffers causing memory corruption.
Observed green lines on the default framebuffer.
Restrict the DMA to maximum height as specified in the S_FMT ioctl.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Allow CAL to be able to export DMA buffer.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
First this patch adds a method to access the CTRL_CORE_CAMERRX_CONTROL
register to use the syscon mechanism. For backward compatibility we also
handle using the existing camerrx_control "reg" entry if a syscon node
is not found.
In addition the register bit layout for the CTRL_CORE_CAMERRX_CONTROL
changes depending on the device. In order to support this we need to use
a register access scheme based on data configuration instead of using
static macro.
In this case we make use of the regmap facility and create data set
based on the various device and phy available.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Looks like the preferred macro to define a single bit mask is BIT() and
not BIT_MASK().
Signed-off-by: Benoit Parrot <bparrot@ti.com>
[hverkuil-cisco@xs4all.nl: fix checkpatch warnings for CAL_HL_IRQ_MASK]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need support
for time64_t.
In completely unrelated work, I spent time on cleaning up parts of this
file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the rest
of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which is
the scsi ioctl handlers. I have patches for those as well, but they need
more testing or possibly a rewrite.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgCl
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
-----BEGIN PGP SIGNATURE-----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=Hj7G
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of stuff in here, though it hasn't been too insane this merge
apart from dealing with the security fun.
uapi:
- export different colorspace properties on DP vs HDMI
- new fourcc for ARM 16x16 block format
- syncobj: allow querying last submitted timeline value
- DRM_FORMAT_BIG_ENDIAN defined as unsigned
core:
- allow using gem vma manager in ttm
- connector/encoder/bridge doc fixes
- allow more than 3 encoders for a connector
- displayport mst suspend/resume reprobing support
- vram lazy unmapping, uniform vram mm and gem vram
- edid cleanups + AVI informframe bar info
- displayport helpers - dpcd parser added
dp_cec:
- Allow a connector to be associated with a cec device
ttm:
- pipelining with no_gpu_wait fix
- always keep BOs on the LRU
sched:
- allow free_job routine to sleep
i915:
- Block userptr from mappable GTT
- i915 perf uapi versioning
- OA stream dynamic reconfiguration
- make context persistence optional
- introduce DRM_I915_UNSTABLE Kconfig
- add fake lmem testing under unstable
- BT.2020 support for DP MSA
- struct mutex elimination
- Tigerlake display/PLL/power management improvements
- Jasper Lake PCH support
- refactor PMU for multiple GPUs
- Icelake firmware update
- Split out vga + switcheroo code
amdgpu:
- implement dma-buf import/export without helpers
- vega20 RAS enablement
- DC i2c over aux fixes
- renoir GPU reset
- DC HDCP support
- BACO support for CI/VI asics
- MSI-X support
- Arcturus EEPROM support
- Arcturus VCN encode support
- VCN dynamic powergating on RV/RV2
amdkfd:
- add navi12/14/renoir support to kfd
radeon:
- SI dpm fix ported from amdgpu
- fix bad DMA on ppc platforms
gma500:
- memory leak fixes
qxl:
- convert to new gem mmap
exynos:
- build warning fix
komeda:
- add aclk sysfs attribute
v3d:
- userspace cleanup uapi change
i810:
- fix for underflow in dispatch ioctls
ast:
- refactor show_cursor
mgag200:
- refactor show_cursor
arcgpu:
- encoder finding improvements
mediatek:
- mipi_tx, dsi and partial crtc support for MT8183 SoC
- rotation support
meson:
- add suspend/resume support
omap:
- misc refactors
tegra:
- DisplayPort support for Tegra 210, 186 and 194.
- IOMMU-backed DMA API fixes
panfrost:
- fix lockdep issue
- simplify devfreq integration
rcar-du:
- R8A774B1 SoC support
- fixes for H2 ES2.0
sun4i:
- vcc-dsi regulator support
virtio-gpu:
- vmexit vs spinlock fix
- move to gem shmem helpers
- handle large command buffers with cma"
* tag 'drm-next-2019-11-27' of git://anongit.freedesktop.org/drm/drm: (1855 commits)
drm/amdgpu: invalidate mmhub semaphore workaround in gmc9/gmc10
drm/amdgpu: initialize vm_inv_eng0_sem for gfxhub and mmhub
drm/amd/amdgpu/sriov skip RLCG s/r list for arcturus VF.
drm/amd/amdgpu/sriov temporarily skip ras,dtm,hdcp for arcturus VF
drm/amdgpu/gfx10: re-init clear state buffer after gpu reset
merge fix for "ftrace: Rework event_create_dir()"
drm/amdgpu: Update Arcturus golden registers
drm/amdgpu/gfx10: fix out-of-bound mqd_backup array access
drm/amdgpu/gfx10: explicitly wait for cp idle after halt/unhalt
Revert "drm/amd/display: enable S/G for RAVEN chip"
drm/amdgpu: disable gfxoff on original raven
drm/amdgpu: remove experimental flag for Navi14
drm/amdgpu: disable gfxoff when using register read interface
drm/amdgpu/powerplay: properly set PP_GFXOFF_MASK (v2)
drm/amdgpu: fix bad DMA from INTERRUPT_CNTL2
drm/radeon: fix bad DMA from INTERRUPT_CNTL2
drm/amd/display: Fix debugfs on MST connectors
drm/amdgpu/nv: add asic func for fetching vbios from rom directly
drm/amdgpu: put flush_delayed_work at first
drm/amdgpu/vcn2.5: fix the enc loop with hw fini
...
Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of the
patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs apis
so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over time,
it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules and
have it "just work" for a variety of platforms (like a distro kernel)
The big problem turned out to be a lack of depandancy information
between different areas of DT entries, and the work here resolves that
problem and now allows devices to boot properly, and quicker than a
monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd6m6Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yntJQCcCqg6RQ7LTdHuZv1ETeefXlsfk00An1Jtean6
42bWGx52bGFvAcpjWy8R
=P7hq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core patches for 5.5-rc1
There's a few minor cleanups and fixes in here, but the majority of
the patches in here fall into two buckets:
- debugfs api cleanups and fixes
- driver core device link support for boot dependancy issues
The debugfs api cleanups are working to slowly refactor the debugfs
apis so that it is even harder to use incorrectly. That work has been
happening for the past few kernel releases and will continue over
time, it's a long-term project/goal
The driver core device link support missed 5.4 by just a bit, so it's
been sitting and baking for many months now. It's from Saravana Kannan
to help resolve the problems that DT-based systems have at boot time
with dependancy graphs and kernel modules. Turns out that no one has
actually tried to build a generic arm64 kernel with loads of modules
and have it "just work" for a variety of platforms (like a distro
kernel). The big problem turned out to be a lack of dependency
information between different areas of DT entries, and the work here
resolves that problem and now allows devices to boot properly, and
quicker than a monolith kernel.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits)
tracing: Remove unnecessary DEBUG_FS dependency
of: property: Add device link support for interrupt-parent, dmas and -gpio(s)
debugfs: Fix !DEBUG_FS debugfs_create_automount
of: property: Add device link support for "iommu-map"
of: property: Fix the semantics of of_is_ancestor_of()
i2c: of: Populate fwnode in of_i2c_get_board_info()
drivers: base: Fix Kconfig indentation
firmware_loader: Fix labels with comma for builtin firmware
driver core: Allow device link operations inside sync_state()
driver core: platform: Declare ret variable only once
cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h>
crypto: hisilicon: no need to check return value of debugfs_create functions
driver core: platform: use the correct callback type for bus_find_device
firmware_class: make firmware caching configurable
driver core: Clarify documentation for fwnode_operations.add_links()
mailbox: tegra: Fix superfluous IRQ error message
net: caif: Fix debugfs on 64-bit platforms
mac80211: Use debugfs_create_xul() helper
media: c8sectpfe: no need to check return value of debugfs_create functions
of: property: Add device link support for iommus, mboxes and io-channels
...
Here is the big set of USB patches for 5.5-rc1
Lots of little things in here:
- typec updates and additions
- usb-serial drivers cleanups and fixes
- misc USB drivers cleanups and fixes
- gadget drivers new features and controllers added
- usual xhci additions
- other minor changes
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXd5+Iw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylA4wCbB3P206oHeHLBe9Eika3D8gM9/fMAn2oWlmpB
Xh7wr30FGC02zU/KBpJ1
=U5qC
-----END PGP SIGNATURE-----
Merge tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.5-rc1
Lots of little things in here:
- typec updates and additions
- usb-serial drivers cleanups and fixes
- misc USB drivers cleanups and fixes
- gadget drivers new features and controllers added
- usual xhci additions
- other minor changes
All of these have been in linux-next with no reported issues"
* tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
usb: gadget: udc: gr_udc: create debugfs directory under usb root
usb: gadget: atmel: create debugfs directory under usb root
usb: musb: create debugfs directory under usb root
usb: serial: Fix Kconfig indentation
usb: misc: Fix Kconfig indentation
usb: gadget: Fix Kconfig indentation
usb: host: Fix Kconfig indentation
usb: dwc3: Fix Kconfig indentation
usb: gadget: configfs: Fix missing spin_lock_init()
usb-storage: Disable UAS on JMicron SATA enclosure
USB: documentation: flags on usb-storage versus UAS
USB: uas: heed CAPACITY_HEURISTICS
USB: uas: honor flag to avoid CAPACITY16
usb: host: xhci-tegra: Correct phy enable sequence
usb-serial: cp201x: support Mark-10 digital force gauge
usb: chipidea: imx: pinctrl for HSIC is optional
usb: chipidea: imx: refine the error handling for hsic
usb: chipidea: imx: change hsic power regulator as optional
usb: chipidea: imx: check data->usbmisc_data against NULL before access
usb: chipidea: core: change vbus-regulator as optional
...
-----BEGIN PGP SIGNATURE-----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=VN90
-----END PGP SIGNATURE-----
Merge tag 'media/v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- uAPI documentation for stateless decoders
- Added a new CEC ioctl together with its documentation
- Improved IPU3 documentation
- New i2c drivers: hi556 and imx290
- Added support on Vivid driver for meta streams
- Added de-interlace support for sunxi subdriver
- Added a few new remote controler keymaps
- Added H.265 support for Sunxi Cedrus driver
- Another round of random driver cleanups, fixes and improvements
* tag 'media/v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (361 commits)
media: Revert "media: mtk-vcodec: Remove extra area allocation in an input buffer on encoding"
media: hantro: Set H264 FIELDPIC_FLAG_E flag correctly
media: hantro: Remove now unused H264 pic_size
media: hantro: Use output buffer width and height for H264 decoding
media: hantro: Reduce H264 extra space for motion vectors
media: hantro: Fix H264 motion vector buffer offset
media: ti-vpe: vpe: fix compatible to match bindings
media: dt-bindings: media: ti-vpe: Document VPE driver
media: zr364xx: remove redundant assigmnent to idx, clean up code
media: Documentation: media: *_DEFAULT targets for subdevs
media: hantro: Fix s_fmt for dynamic resolution changes
media: i2c: Use the correct style for SPDX License Identifier
media: siano: Use the correct style for SPDX License Identifier
media: vicodec: media_device_cleanup was called too early
media: vim2m: media_device_cleanup was called too early
media: cedrus: Increase maximum supported size
media: cedrus: Fix H264 4k support
media: cedrus: Properly signal size in mode register
media: v4l2-ctrl: Lock main_hdl on operations of requests_queued.
media: si470x-i2c: add missed operations in remove
...
* patchwork: (360 commits)
media: Revert "media: mtk-vcodec: Remove extra area allocation in an input buffer on encoding"
media: hantro: Set H264 FIELDPIC_FLAG_E flag correctly
media: hantro: Remove now unused H264 pic_size
media: hantro: Use output buffer width and height for H264 decoding
media: hantro: Reduce H264 extra space for motion vectors
media: hantro: Fix H264 motion vector buffer offset
media: ti-vpe: vpe: fix compatible to match bindings
media: dt-bindings: media: ti-vpe: Document VPE driver
media: zr364xx: remove redundant assigmnent to idx, clean up code
media: Documentation: media: *_DEFAULT targets for subdevs
media: hantro: Fix s_fmt for dynamic resolution changes
media: i2c: Use the correct style for SPDX License Identifier
media: siano: Use the correct style for SPDX License Identifier
media: vicodec: media_device_cleanup was called too early
media: vim2m: media_device_cleanup was called too early
media: cedrus: Increase maximum supported size
media: cedrus: Fix H264 4k support
media: cedrus: Properly signal size in mode register
media: v4l2-ctrl: Lock main_hdl on operations of requests_queued.
media: si470x-i2c: add missed operations in remove
...
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl3bzrQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LkMB/4/MkpN4F2WudNCKgmYay2gw3hq8aOR
5Xh/SE6N3BEgBpQiMEUdePRT6LqnQMsSpOaUoKfd4nFvCyLaV7itaYzQuUpo+UJ/
a4UDHJPVfrDJeFghWqSngfEW/N66mpO3UuAvhSRTR3ku0T31v9FkcLsMbdxVUpLC
ablSaFfPCOtTQOsG9blRUL/GAWUhGzPI/Hl4VldS0FvKDmMDY2fxt7QxXRaEYItc
i1Uthklxd0BfRmDqv0WEpduUhbwzg6Uir9pXSisux7DpMk1Li0IyPST5UcRl0Zf4
CKL/qfdQANpufj9kGmrlCOnXB9P5/XYVwfYV430WqMyw0QaOzzSrxT7C
=CZ/+
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: More updates for v5.5
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pass the device pointer from the PCI pointer directly, instead of a
non-standard macro. The macro didn't give any better readability.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent change (commit 08422d2c55: "ALSA: memalloc: Allow NULL
device for SNDRV_DMA_TYPE_CONTINOUS type") made the PCM preallocation
helper accepting NULL as the device pointer for the default usage.
Drop the snd_dma_continuous_data() usage that became superfluous from
the callers.
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 3192b2ca79.
There are indications that this patch causes problems on some
platforms due to some hardware prefetch. Reverting this patch
for now until this is better understood.
Reported-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Update the compatible string to match the updated bindings.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The variable cable_type is being initialized with a value that
is never read and is being re-assigned a little later on. Replace
the redundant initializtion with the assignment that occurs a little
later. Also initialize frm too rather than have a later assignment.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch corrects the SPDX License Identifier style
in header files related to I2C controlled media codec drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
and some manual changes.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch corrects the SPDX License Identifier style
in header file related to Siano Mobile Silicon Digital TV.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There's a race condition between the list_del_init in the
v4l2_ctrl_request_complete, and the list_add_tail in the
v4l2_ctrl_request_queue, since they can be called in different thread
and the requests_queued list is not protected by a lock. This can lead
to that the v4l2_ctrl_handler is still in the requests_queued list while
the request_is_queued is already set to false, which would cause
use-after-free if the v4l2_ctrl_handler is later released.
Fix this by locking the ->lock of main_hdl (which is the owner of the
requests_queued list) when doing list operations on the
->requests_queued list.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver misses calling v4l2_ctrl_handler_free and
v4l2_device_unregister in remove like what is done in probe failure.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Disable output side crop selections for the decoder.
This fixes the following v4l2-compliance complaint:
fail: v4l2-test-formats.cpp(1576): IS_DECODER(node)
test Cropping: FAIL
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
v4l2_vbi_format, v4l2_sliced_vbi_format and v4l2_sdr_format
have a reserved array at the end that should be zeroed by drivers
as per the V4L2 spec. Older drivers often do not do this, so just
handle this in the core.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Disable capture side compose selections for the encoder.
This fixes the following v4l2-compliance complaint:
fail: v4l2-test-formats.cpp(1662): IS_ENCODER(node)
test Composing: FAIL
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MediaTek encoder allocates non pixel data area for an input buffer every
plane. As the input buffer should be read-only, the driver should not write
anything in the buffer. Therefore, the extra data should be unnecessary.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In the implementation of aspeed_video_probe() the allocated memory for
video should be released if either devm_ioremap_resource()
or aspeed_video_init() or aspeed_video_setup_video() fails. Replace
kzalloc() with devm_kzalloc to avoid explicit release for video.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It's more clear to use FIELD_SIZEOF instead of its implementation.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Beelink GS1 Andoid TV Box ships with a simple NEC remote.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
remove unused code
Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
An earlier commit hard coded a return 0 to function flexcop_usb_i2c_req
even though the an -EIO was intended to be returned in the case where
ret != buflen. Fix this by replacing the return 0 with the return of
ret to return the error return code.
Addresses-Coverity: ("Unused value")
Fixes: b430eaba0b ("[media] flexcop-usb: don't use stack for DMA")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver needs an isochronous endpoint to be present. It will
oops in its absence. Add checking for it.
Reported-by: syzbot+d93dff37e6a89431c158@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The irqlock spinlock has been unused from the start. Remove it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In some device configurations there's no radio or radio support in the
driver. That's OK, as the driver sets itself up accordingly. However
on tear-down in these caes it's still trying to tear down radio
related context when there isn't anything there, leading to
dereferences through a null pointer and chaos follows.
How this bug survived unfixed for 11 years in the pvrusb2 driver is a
mystery to me.
[hverkuil: fix two checkpatch warnings]
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
v4l2_compat_ioctl32() is the function that calls into
v4l2_file_operations->compat_ioctl32(), so setting that back to the same
function leads to a trivial endless loop, followed by a kernel
stack overrun.
Remove the incorrect assignment.
Cc: stable@vger.kernel.org
Fixes: 7472c1c691 ("[media] media: venus: vdec: add video decoder files")
Fixes: aaaa93eda6 ("[media] media: venus: venc: add video encoder files")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Hold buf flag is set on output queue, not capture. Fix that.
Fixes: f07602ac38 ("media: v4l2-mem2mem: add new_frame detection")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The field kthread_sen in the vimc_sen_device is
not set and used. So remove the field and
the code that check if it is non NULL
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Cc: <stable@vger.kernel.org> # for v5.4 and up
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
After adding a const pointer to ctrl_ptr, lets use it where it make
sense.
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This control represents a generic read/write area.
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This allows setting the default value on compound controls created via
v4l2_ctrl_new_custom.
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When driver is built as module and probe during insmod is deferred
because of sensor subdevs, there is NULL pointer deference because
mdev is cleaned up and then access it from v4l2_device_unregister().
Fix the wrong mdev and v4l2 dev order in error path of probe.
This fixes below null pointer deference:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ca026f68
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[...]
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
PC is at ida_free+0x7c/0x160
LR is at xas_start+0x44/0x204
[...]
[<c0dafd60>] (ida_free) from [<c083c20c>] (__media_device_unregister_entity+0x18/0xc0)
[<c083c20c>] (__media_device_unregister_entity) from [<c083c2e0>] (media_device_unregister_entity+0x2c/0x38)
[<c083c2e0>] (media_device_unregister_entity) from [<c0843404>] (v4l2_device_release+0xd0/0x104)
[<c0843404>] (v4l2_device_release) from [<c0632558>] (device_release+0x28/0x98)
[<c0632558>] (device_release) from [<c0db1204>] (kobject_put+0xa4/0x208)
[<c0db1204>] (kct_put) from [<bf00bac4>] (fimc_capture_subdev_unregistered+0x58/0x6c [s5p_fimc])
[<bf00bac4>] (fimc_capture_subdev_unregistered [s5p_fimc]) from [<c084a1cc>] (v4l2_device_unregister_subdev+0x6c/0xa8)
[<c084a1cc>] (v4l2_device_unregister_subdev) from [<c084a350>] (v4l2_device_unregister+0x64/0x94)
[<c084a350>] (v4l2_device_unregister) from [<bf0101ac>] (fimc_md_probe+0x4ec/0xaf8 [s5p_fimc])
[...]
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Fixes: 9832e155f1 ("[media] media-device: split media initialization and registration")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is the same incorrect approach to locking implemented in
vivid_stop_generating_vid_cap(), vivid_stop_generating_vid_out() and
sdr_cap_stop_streaming().
These functions are called during streaming stopping with vivid_dev.mutex
locked. And they all do the same mistake while stopping their kthreads,
which need to lock this mutex as well. See the example from
vivid_stop_generating_vid_cap():
/* shutdown control thread */
vivid_grab_controls(dev, false);
mutex_unlock(&dev->mutex);
kthread_stop(dev->kthread_vid_cap);
dev->kthread_vid_cap = NULL;
mutex_lock(&dev->mutex);
But when this mutex is unlocked, another vb2_fop_read() can lock it
instead of vivid_thread_vid_cap() and manipulate the buffer queue.
That causes a use-after-free access later.
To fix those issues let's:
1. avoid unlocking the mutex in vivid_stop_generating_vid_cap(),
vivid_stop_generating_vid_out() and sdr_cap_stop_streaming();
2. use mutex_trylock() with schedule_timeout_uninterruptible() in
the loops of the vivid kthread handlers.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: <stable@vger.kernel.org> # for v3.18 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Refactor some of the vivid_create_instance code by using a
new vivid_create_queue() helper function.
Also add some sanity checks for the node_types vs input/output_types
module options.
This patch resolves these two smatch parse errors:
drivers/media/platform/vivid/vivid-core.c:1679 vivid_create_instance() parse error: OOM: 3002600Kb sm_state_count = 6160113
drivers/media/platform/vivid/vivid-core.c: drivers/media/platform/vivid/vivid-core.c:1679
vivid_create_instance() parse error: __split_smt: function too hairy. Giving up after 33 seconds
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Macros MSG_SMS_ENBALE_TS_INTERFACE_REQ and MSG_SMS_ENBALE_TS_INTERFACE_RES
contain a spelling mistake. Fix these by replacing ENBALE with ENABLE.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Drop two dprintk's that relied on a non-NULL mantis pointer
when it was in fact a NULL pointer.
Fix those warnings:
drivers/media/pci/mantis/mantis_cards.c:73 mantis_irq_handler() error: we previously assumed 'mantis' could be null (see line 72)
drivers/media/pci/mantis/hopper_cards.c:64 hopper_irq_handler() error: we previously assumed 'mantis' could be null (see line 63)
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Initialize ret to 0 to fix this smatch error:
drivers/media/i2c/ov6650.c:853 ov6650_video_probe() error: uninitialized symbol 'ret'.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch fixes this error:
drivers/media/platform/ti-vpe/vpdma.c:767 dump_dtd() error: '%pad' expects argument of type 'dma_addr_t*', argument 2 has type 'uint*'
dtd->start_addr is a u32, so no need for %pad.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use sizeof instead of ARRAY_SIZE to fix this smatch warning:
drivers/media/usb/em28xx/em28xx-i2c.c:952 em28xx_do_i2c_scan() warn: calling memset(x, y, ARRAY_SIZE());
Do the same for the em28xx_hash_mem() call in the same function.
smatch didn't pick that up, but there too it should use sizeof instead
of ARRAY_SIZE.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use sizeof instead of ARRAY_SIZE to fix this smatch warning:
drivers/media/rc/ite-cir.c:385 ite_tx_ir() warn: calling memset(x, y, ARRAY_SIZE());
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fixes this warning:
drivers/media/platform/am437x/am437x-vpfe.c:288 vpfe_ccdc_validate_param() warn: unsigned 'ccdcparam->alaw.gamma_wd' is never less than zero.
by dropping the gamma_wd < VPFE_CCDC_GAMMA_BITS_15_6 check
since VPFE_CCDC_GAMMA_BITS_15_6 is 0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Instead of validating the links to capture devices and subdevices with
the same function, use the default v4l function for links between
subdevices and only use a different function for validating between
capture device and subdevice.
This change should also ease future work to associate multiple mbus
codes for the same pixelformat in vimc_pix_map.
These changes were tested with
v4l2-compliance SHA: 3f806630e2ecbcebe31872b865c5c4b42f111a99, 64 bits
and passed all tests:
Grand Total for vimc device /dev/media0: 451, Succeeded: 451, Failed: 0, Warnings: 0
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@protonmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a V4L2 sub-device driver for Hynix Hi-556 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
+ 2592x1944 at 30FPS
+ 1296x972 at 30FPS
[sakari.ailus@linux.intel.com: Remove MEDIA_CAMERA_SUPPORT from Kconfig dependencies]
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The number of components are only set, and never used.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The official name is "R-Car M3-N", not "R-Car M3N".
Fixes: 4e8c120de9 ("media: fdp1: Support M3N and E3 platforms")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace F* word with something less offensive.
[hverkuil: dropped 'Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")' tag since nothing was broken]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The kernel driver never touches the decoded buffers with the CPU.
All accesses are either done by hardware DMA masters or userspace
mapping the buffers. This means we don't need a kernel virtual
address mapping for those buffers at all. As those buffers are
usually quite large, we can save a good deal of kernel vmalloc
space by requesting to not have a kernel mapping set up for them.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The BIT decoder picture run temporarily locks the bitstream mutex while
the coda device mutex is locked, to refill the bitstream ring buffer.
Consequently, the decoder start command, which locks both mutexes when
flushing the bitstream ring buffer, must lock the coda device mutex
first as well, to avoid an ABBA deadlock.
Fixes: e7fd95849b ("media: coda: flush bitstream ring buffer on decoder restart")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
v4l_s_fmt, for VFL_TYPE_TOUCH, sets unneeded members of
the v4l2_pix_format structure to default values.This was
missing in v4l_g_fmt, which would lead to failures in
v4l2-compliance tests.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit a8fa55078a ("media: v4l2-subdev: Verify arguments in
v4l2_subdev_call()") and commit 374d62e7aa ("media: v4l2-subdev:
Verify v4l2_subdev_call() pad config argument") introduced a few local
functions, unfortunately with arguments of type __u32, reserved for use
in Linux uAPI. Use u32 instead.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
>From isp_video_release(), &isp->video_lock is held and subsequent
vb2_fop_release() tries to lock vdev->lock which is same with the
previous one. Replace vb2_fop_release() with _vb2_fop_release() to
fix the recursive locking.
Fixes: 1380f5754c ("[media] videobuf2: Add missing lock held on vb2_fop_release")
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
"f->fmt.sdr.reserved" is uninitialized. As other peer drivers
like msi2500 and airspy do, the fix initializes it to avoid
memory disclosures.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the MIPI CSI-2 driver support for RZ/G2N(R8A774B1) SoC.
The CSI-2 module of RZ/G2N is similar to R-Car M3-N.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the SoC specific information for RZ/G2N(R8A774B1) SoC.
The VIN module of RZ/G2N is similar to R-Car M3-N.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Most Gen3 boards can output frames in NV12 format, add support for this
with a runtime check that the running hardware supports it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Most but not all Gen3 hardware support outputting NV12, add a flag to
indicate which SoCs do support it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If a pixel format is not supported by the hardware NULL is returned by
rvin_format_from_pixel() for that fourcc. Verify that the pixel format
is supported using this or skip it when enumerating.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If a process is interrupted while accessing the radio device and the
core lock is contended, release() could return early and fail to update
the interrupt mask.
Note that the return value of the v4l2 release file operation is
ignored.
Fixes: 87d1a50ce4 ("[media] V4L2: WL1273 FM Radio: TI WL1273 FM radio driver")
Cc: stable <stable@vger.kernel.org> # 2.6.38
Cc: Matti Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If a process is interrupted while accessing the video device and the
device lock is contended, release() could return early and fail to free
related resources.
Note that the return value of the v4l2 release file operation is
ignored.
Fixes: 28ffeebbb7 ("[media] bdisp: 2D blitter driver using v4l2 mem2mem framework")
Cc: stable <stable@vger.kernel.org> # 4.2
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't populate the array input_vals on the stack but instead make it
static. Makes the object code smaller by 106 bytes.
Before:
text data bss dec hex filename
11744 3536 128 15408 3c30 drivers/media/i2c/vpx3220.o
After:
text data bss dec hex filename
11574 3600 128 15302 3bc6 drivers/media/i2c/vpx3220.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch corrects the SPDX License Identifier style
in header files related to Video drivers for Xilinx devices.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Variable status is being initialized with a value that is never read
and is being re-assigned a later on. The assignment is redundant and
hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
We added two new error paths to smiapp_start_streaming(), but we can't
return directly without dropping the "sensor->mutex" lock.
Fixes: f8c4352c1b ("media: smiapp: Move binning configuration to streaming start")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Allwinner H3 SoC contains deinterlace unit, which has several modes of
operation - bypass, weave, bob and mixed (advanced) mode. I don't know
how mixed mode works, but according to Allwinner it gives best results,
so they use it exclusively. Currently this mode is also hardcoded here.
For each interleaved frame queued, this driver produces 2 deinterlaced
frames. Deinterlaced frames are based on 2 consequtive output buffers,
except for the first 2, where same output buffer is given to peripheral
as current and previous.
There is no documentation for this core, so register layout and fixed
values were taken from BSP driver.
I'm not sure if maximum size of the image unit is capable to process is
governed by size of "flag" buffers, frequency or it really is some HW
limitation. Currently driver can process full HD image in ~15ms (7.5ms
for each capture buffer), which allows to process 1920x1080@60i video
smoothly in real time.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[hverkuil-cisco@xs4all.nl: add static to deinterlace_ioctl_ops]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add mean window size parameter for debayer filter as a control in
vimc-debayer.
vimc-debayer was patched to allow changing mean window parameter
of the filter without needing to reload the driver. The parameter
can now be set using a v4l2-ctl control(mean_window_size).
Co-developed-by: Laís Pessine do Carmo <laispc19@gmail.com>
Signed-off-by: Laís Pessine do Carmo <laispc19@gmail.com>
Signed-off-by: Arthur Moraes do Lago <arthurmoraeslago@gmail.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the 'struct device *dev' field exists in each of the
entity structs, it can be moved to the common struct vimc_ent_devevice.
It is then used to replace 'pr_err' with 'dev_err' in the streamer
code.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
since the pads array is of known small size, there is no reason to
allocate it separately. Instead, it is embedded in the entity struct.
This also conforms to the media controller doc:
'Most drivers will embed the pads array in a driver-specific structure,
avoiding dynamic allocation.'
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
[hverkuil-cisco@xs4all.nl: remove unused vimc_pads_init()]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
the struct vimc_platform_data is not used anymore and can be removed.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function 'vimc_pipeline_s_stream' is not used and can be
removed.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vimc is a single kernel module and does not need to
export any symbols therefore there is no need for these
declarations.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
since this function only calls v4l2_device_unregister_subdev,
it is pointless.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
according to the docs, this function must be called during
the cleanup phase after unregistering the entity.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vimc_sen_add function first registers the subdevice and then
calls tpg_alloc. If tpg_alloc fails it unregisters the subdevice
and then frees vsen, this cause double free since the release
callback that follows subdevice unregistration also frees vsen.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the add callback returns NULL on failure and the array
is initialized to NULLs, there is no need for the intermediate
assignment to local var.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
since NULL value for vimc entity pointer indicates
that entity creation failed and this is tested, the
pointers should be initialized to NULL.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch corrects the SPDX License Identifier style
in header file related to media Drivers for Analog TV Tuners.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename the confusingly named smiapp_update_mode() function as
smiapp_pll_blanking_update(). The function is used to calculate new PLL
and blanking configuration after binning or scaling configuration has been
changed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Earlier it was possible that the parts of the driver that assumed runtime
PM was enabled were being called before runtime PM was enabled in the
driver's probe function. So enable runtime PM before registering the
sub-device.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use non-binned limits when binning is disabled and binned when they're
enabled.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sensor configuration since it was previously powered off was not
changed, so no need to update the PLL configuration etc. What is necessary
though is to re-apply the configuration to the sensor's registers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Only write the binning configuration at stream start. It has no effect
otherwise.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver implementation assumed the binning limits could change
dynamically based on the binning configuration. This is not actually the
case; these limits are static and suitable to be used with all binning
configurations but possibly not optimal limit for many of those
configurations.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Destroy the mutex initialised by the driver in probe.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The interface supports probing for the NVM size but this was not
implemented in the driver. Do that now.
This will also make nokia,nvm-size property redundant.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Only some devices require polling for NVM ready. Do the polling only on
devices that need it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The data transfer capability register was defined but its bits were not.
Do that now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Split out reading a single NVM page into a separate function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If NVM reading failed, the device was left powered on. Fix that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The BIT macro is a better way to define register bits, for 1 << bit is
risky for 32-bit registers.
Also remove the definition of SMIAPP_DATA_TRANSFER_IF_1_CTRL_RD_EN which
has a value of zero.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
mipid02_probe misses a check for devm_gpiod_get_optional and may miss
the failure.
Add a check to fix the problem.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add driver for Sony IMX290 CMOS image sensor driver. The driver only
supports I2C interface for programming and MIPI CSI-2 for sensor output.
[Sakari Ailus: Rewrapped a few lines over 80 chars a little.]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If VIDEO_OV5695 is y and V4L2_FWNODE is m, building fails:
drivers/media/i2c/ov5695.o: In function `ov5695_probe':
ov5695.c:(.text+0xf4c): undefined reference to `v4l2_async_register_subdev_sensor_common'
Select V4L2_FWNODE like OV5675 does.
Fixes: 623df5d710 ("media: i2c: ov5695: Modify the function of async register subdev related devices")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
According to the datasheet, both AD5821 and AD5820 share a compatible
register-set:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5821.pdf
Some camera modules also refer that AD5823 is a replacement of AD5820:
https://download.kamami.com/p564094-OV8865_DS.pdf
Suggested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since kernel 4.16, i2c devices with DT compatible tag are modprobed
using their DT modalias.
Without this patch, if this driver is build as module it would never
be autoprobed.
There is no need to mask it with CONFIG_OF to allow ACPI loading, this
also builds find with CONFIG_OF=n.
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds support for a programmable enable pin. It can be used in
situations where the ANA-vcc is not configurable (dummy-regulator), or
just to have a more fine control of the power saving.
The use of the enable pin is optional.
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Without this patch, media_device_register_entity throws a warning:
dev_warn(mdev->dev,
"Entity type for entity %s was not initialized!\n",
entity->name);
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sensor data sheet clearly state that 2592x1944 only works at 15 fps
make sure we don't try to miss configure the pll out of acceptable
range.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the 1920x1080 register array an extra pair of reset ctrl disable
re-enable was causing unwanted init delays.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add v4l2 controls to report the pixel rates of each mode. This is
needed by some CSI2 receiver in order to perform proper DPHY
configuration.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The variable rval is being initialized with a value that
is never read and is being re-assigned a little later on. The
assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A hardcoded 12 MHz master clock frequency has been assumed since
conversion of the driver from soc_camera sensor to a standalone V4L2
subdevice by commit 23a52386fa ("media: ov6650: convert to standalone
v4l2 subdevice"). Fix it.
Define a static table of supported master clock rates (fix misnamed
symbol while being at it), then use v4l2_clk_get/set_rate() to obtain
a clock rate matching one of those supported. On success, apply
respective master clock hardware divisor provided by the matching
element of the table.
[Sakari Ailus: Initialize xclk to NULL.]
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This field of the driver private structure is no longer used, drop it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As calculation of pixel clock hardware divisor no longer depends on
mbus format specific maximum pixel clock, there is no need to reapply
the divisor on format change. Drop related code from ov6650_s_fmt()
helper.
Since a master clock hardware divisor, so far applied only together
with the pixel clock divisor in a single operation, will no longer be
applied from ov6650_s_fmt(), apply it, still using a hardcoded value
for now, from ov6650_prog_dflt() helper so hardware is still
initialised correctly on device probe.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As appears from an analysis of to_clkrc() helper code after its
pclk_limit argument has been dropped, its result no longer depends on
another argument - pclk_max. Moreover, assuming that a constant value
of FRAME_RATE_MAX is always used as a denominator of the only
significant argument left - a struct v4l2_fract, the result in fact
depends only on the numerator value of that argument. As a further
consequence, it no longer makes sense to recalculate frame intervals by
converting them forth and back with a GET_CLKRC_DIV(to_clkrc(tpf))
construct.
Drop use of GET_CLKRC_DIV() on results of to_clkrc() where possible -
use the frame interval value directly. Furthermore, replace the
to_clkrc() helper function with a simple macro and update its users to
always use FRAME_RATE_MAX as frame interval denominator and pass only
its numerator as an argument.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
That attribute used to be obtained from platform data by a soc_camera
host interface and passed to the sensor driver for .s_mbus_fmt() video
operation callback, later reused as .set_fmt() pad operation callback,
to be able to limit frame rate. The driver stored that value in its
private structure for further use from .g/s_parm(), later converted to
g/s_frame_interval().
On conversion of the driver from soc_camera sensor to a standalone V4L2
subdevice by commit 23a52386fa ("media: ov6650: convert to standalone
v4l2 subdevice"), that attribute had been replaced by a constant and
hardcoded to an arbitrarily chosen pixel clock limit. Drop it. Host
interfaces can limit frame rate if needed by calling
.s_frame_interval().
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver stores a frame interval value supposed to be in line with
hardware state in a device private structure. Since the driver initial
submission, the respective field of the structure has never been
initialised on device probe. Moreover, if updated from
.s_frame_interval(), a new value is stored before it is applied on
hardware. If an error occurs during device update, the stored value
may no longer reflect hardware state and consecutive calls to
.g_frame_interval() may return incorrect information.
Assuming a failed update of the device means its actual state hasn't
changed, update the frame interval field of the device private
structure with a new value only after it is successfully applied on
hardware so it always reflects actual hardware state to the extent
possible. Also, initialise the field with hardware default frame
interval on device probe.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CONFIG_PREEMPTION is selected by CONFIG_PREEMPT and by CONFIG_PREEMPT_RT.
Both PREEMPT and PREEMPT_RT require the same functionality which today
depends on CONFIG_PREEMPT.
Switch the Kconfig dependency to CONFIG_PREEMPTION.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Don't populate the array 'cri' on the stack but instead make it
static and const. Makes the object code smaller by 165 bytes.
Turn the 2nd parameter of 'log_infoframe()' const accordingly.
Before:
text data bss dec hex filename
98533 20024 256 118813 1d01d drivers/media/i2c/adv7842.o
After:
text data bss dec hex filename
98304 20088 256 118648 1cf78 drivers/media/i2c/adv7842.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The variable ret is being initialized with a value that
is never read and is being re-assigned a little later on. The
assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There appears to be a copy-paste error on the access of
csc_coeffs.y2r.r601.full.coeff, I believe csc_coeffs.2yr.r601.full.coeff
should be used instead. This is a moot point as the code is never
reached, but at least use the correct structure element.
Addresses-Coverity: ("Copy-paste error")
Fixes: 3ff3a712a9 ("media: ti-vpe: vpe: don't rely on colorspace member for conversion")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the "chip found" message is shown even in the case where the
I2C address is wrongly passed in the device tree, or also in the case of
probe failure, which is misleading.
To avoid such problem, move this message after real I2C transactions
have been successfully made and we are certain that the adv7180 is
really present and probed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In af9005_identify_state when returning -EIO the allocated buffer should
be released. Replace the "return -EIO" with assignment into ret and move
deb_info() under a check.
Fixes: af4e067e1d ("V4L/DVB (5625): Add support for the AF9005 demodulator from Afatech")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Drivers that use the CEC pin framework have no way of processing messages
themselves by providing the 'received' callback. This is present in
cec_ops, but not in cec_pin_ops.
Add support for this callback.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sometimes it detects a weird resolution such as 1024x287 when the
actual resolution is 1024x768. To resolve such an issue, this
commit adds clearing for hsync and vsync polarity register bits
at the beginning of the first mode detection. This is recommended
in the datasheet.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To prevent inaccurate detections of resolution, this commit enables
clearing of hsync/vsync polarity bits based on probed sync state.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This introduces the required definitions for HEVC decoding support with
stateless VPUs. The controls associated to the HEVC slice format provide
the required meta-data for decoding slices extracted from the bitstream.
They are not exported to the public V4L2 API since reworking this API
will likely be needed for covering various use-cases and new hardware.
Multi-slice decoding is exposed as a valid decoding mode to match current
H.264 support but it is not yet implemented.
The interface comes with the following limitations:
* No custom quantization matrices (scaling lists);
* Support for a single temporal layer only;
* No slice entry point offsets support;
* No conformance window support;
* No VUI parameters support;
* No support for SPS extensions: range, multilayer, 3d, scc, 4 bits;
* No support for PPS extensions: range, multilayer, 3d, scc, 4 bits.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[hverkuil-cisco@xs4all.nl: use 1ULL in flags defines in hevc-ctrls.h]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support metadata output in vivid driver.
Metadata output is used to set brightness, contrast, saturation
and hue.
Adds new files for metadata output.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add new metadata format to support metadata output in vivid.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds meatadata capture support in vivid driver.
Adds new files for metadata capture.
Adds vivid controls to generate PTS and SCR for metadata stream.
also fixes v4l2-compliance issues seen on metadata device.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Touch devices have obviously no tuner, so don't attempt to enable those
ioctls for such devices.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Touch devices mark too many ioctls as valid. Restrict the list of
valid ioctls for touch devices.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In determine_valid_ioctls() we can use SET_VALID_IOCTL to enable
ioctls for SDR, simplifying the code.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the type is VFL_TYPE_GRABBER, then also check device_caps
to see if the video device supports video and/or metadata and
disable unneeded ioctls.
Without this change, format ioctls for both video and metadata devices
could be called on both device nodes. This is true for other ioctls as
well, even if the device supports only video or metadata.
Metadata devices act similar to VBI devices w.r.t. which ioctls should
be enabled. This makes sense since VBI *is* metadata.
Signed-off-by: Vandana BN <bnvandana@gmail.com>
Co-developed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The .ioctl and .compat_ioctl file operations have the same prototype so
they can both point to the same function, which works great almost all
the time when all the commands are compatible.
One exception is the s390 architecture, where a compat pointer is only
31 bit wide, and converting it into a 64-bit pointer requires calling
compat_ptr(). Most drivers here will never run in s390, but since we now
have a generic helper for it, it's easy enough to use it consistently.
I double-checked all these drivers to ensure that all ioctl arguments
are used as pointers or are ignored, but are not interpreted as integer
values.
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl2su/AeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGvm4H/1jkheCrvB/GJS69
wd18vizAg+eFmNCzxlGVhpQTKGymNRy+g6clnoli3cNJ3pSVKcYgVyB3oXaONIhp
g/ANudnBjTdjqYgJzfLij5AGecrGwDpF3YL0kuKrCB63s2I/HwQGYy/aPrYY8emy
gAYdaf1DGRu5/DIIB6soTo/TnpKoAyTE+XY5MaPSug++t/Flov19tlU40IZxXW94
bjTXbm0yklrsIx+LL5mYYGGnygSTCF66JjFg1qhDCBQaS2MZ21h1ZgaOtGZTwZcc
WgEiqLC5S1Iyj96zir1t78RcVQ4RzgvDbhUOgIqUFsYAO2wOicvxyFE3Hj8rPOKd
uGgVPRM=
=xgZa
-----END PGP SIGNATURE-----
Merge v5.4-rc4 into drm-next
Thierry needs fd70c7755b ("drm/bridge: tc358767: fix max_tu_symbol
value") to be able to merge his dp_link patch series.
Some adjacent changes conflicts, plus some clashes in i915 due to
cherry-picking and git trying to be helpful and leaving both versions
in.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drivers that support VB2_V4L2_FL_SUPPORTS_M2M_HOLD_CAPTURE_BUF
typically want to know if a new frame is started (i.e. the first
slice is about to be processed). Add a new_frame bool to v4l2_m2m_ctx
and set it accordingly.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These helpers are used by stateless codecs when they support multiple
slices per frame and hold capture buffer flag is set. It's expected that
all such codecs will use this code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Co-developed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Check for held buffers that are ready to be returned to vb2 in
__v4l2_m2m_try_queue(). This avoids drivers having to handle this
case.
Add v4l2_m2m_buf_done_and_job_finish() to correctly return source
and destination buffers and mark the job as finished while taking
a held destination buffer into account (i.e. that buffer won't be
returned). This has to be done while job_spinlock is held to avoid
race conditions.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds support for the V4L2_BUF_FLAG_M2M_HOLD_CAPTURE_BUF
flag.
It also adds a new V4L2_BUF_CAP_SUPPORTS_M2M_HOLD_CAPTURE_BUF
capability.
Drivers should set vb2_queue->subsystem_flags to
VB2_V4L2_FL_SUPPORTS_M2M_HOLD_CAPTURE_BUF to indicate support
for this flag.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is likely that it should be UVC_METADATA_BUF_SIZE instead.
Fix it and use it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When parsing the UVC control descriptors fails, the error path tries to
cleanup a media device that hasn't been initialised, potentially
resulting in a crash. Fix this by initialising the media device before
the error handling path can be reached.
Fixes: 5a254d751e ("[media] uvcvideo: Register a v4l2_device")
Reported-by: syzbot+c86454eb3af9e8a4da20@syzkaller.appspotmail.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
I2C ops are expensive, as the I2C bus typical speed is 100kbps.
Also, stats reading take some time, as it requires to retrieve a
certain number of packets to complete.
While we don't know the minimal for CXD2841er, trying to do it
too quickly is still a very bad idea.
So, add some sanity logic there, preventing to retrieve stats
faster than one second.
This shouldn't cause any issues with well behavior apps, as they
usually take stats on a polling rate slower than 1 second.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
While 99% of the implementation of the bitrate estimation
routine for ISDB-T is generic, the current approach mangles it
with some mb86a20s-specific thing.
Split the calculus from the specific stuff, in order to make
easier to use the same approach on other drivers requiring
a similar formula.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Add a keymap for the Tronsmart Vega S95 and S96 Android (Amlogic S905/S912)
STB devices. Both use the same IR remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: Zhong Jiang <zhongjiang@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The code for pulse and space is the same so remove duplication.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds USB ID for the eyeTV Geniatech T2 lite to the dvbsky driver.
This is a Geniatech T230C based stick without IR and a different USB ID.
Signed-off-by: Thomas Voegtle <tv@lio96.de>
Tested-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Up to now VPE was relying on the colorspace value of struct v4l2_format
as an indication to perform color space conversion from YUV to RGB or
not.
Instead we should used the source/destination fourcc codes as a more
reliable indication to perform color space conversion or not.
To do so, we rework the csc module to use "struct v4l2_format *" as
parameters, and reorganize the coefficients tables in a more logical
way.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is often useful to figure out if a pixel_format is either YUV or RGB
especially for driver who can perform the pixel encoding conversion.
Instead of having each driver implement its own "is_this_yuv/rgb"
function based on a restricted set of pixel value, it is better to do
this in centralized manner.
We therefore add a pixel_enc member to the v4l2_format_info structure to
quickly identify the related pixel encoding.
And add helper functions to check pixel encoding.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The RGB to YUV HD full range coefficients did not match the TRM values
and appeared to be a cut-n-paste from the YUV to RGB section.
Replace the entries with the values from the TRM.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All 4 of the "colorspace" components were not originally handled.
Causing issue related to xfer_func not being initialized properly.
This was found with v4l2-compliance test.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For each queue we need to maintain resolutions, pixel format,
bytesperline, sizeimage, colorspace, etc.
Instead of manually adding more entries in the vpe_q_data struct, it is
better to just add a "struct v4l2_format" member and use that to store
all needed information.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
[hverkuil@xs4all.nl: fix checkpatch warning]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VPE uses VPDMA (built-in dma engine) to transfer data to and from the IP
and memory. VPDMA expect 32 bits addresses. To make sure that is always
the case set the DMA mask and coherent mask for the device.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using dma_addr_t as the type to hold address inside of a fix sized
descriptor used by the vpdma firmware is prone to fail when the expected
width is 32 bits and suddenly when CONFIG_LPAE is enabled the data size
is now 64 bits shifted the remaining members of the descriptor in memory
which confuses the firmware.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(691): ret == 0
fail: v4l2-test-buffers.cpp(974): captureBufs(node, q, m2m_q,
frame_count, true)
test MMAP: FAIL
This caused the following Kernel Warning:
WARNING: CPU: 0 PID: 961 at
drivers/media/v4l2-core/videobuf2-core.c:1658
__vb2_queue_cancel+0x174/0x1d8
...
CPU: 0 PID: 961 Comm: v4l2-compliance Not tainted
4.14.62-01720-g20ecd717e87a #6
Hardware name: Generic DRA72X (Flattened Device Tree)
Backtrace:
[<c020b5bc>] (dump_backtrace) from [<c020b8a0>] (show_stack+0x18/0x1c)
r7:00000009 r6:60070013 r5:00000000 r4:c1053824
[<c020b888>] (show_stack) from [<c09232e8>] (dump_stack+0x90/0xa4)
[<c0923258>] (dump_stack) from [<c022b740>] (__warn+0xec/0x104)
r7:00000009 r6:c0c0ad50 r5:00000000 r4:00000000
[<c022b654>] (__warn) from [<c022b810>] (warn_slowpath_null+0x28/0x30)
r9:00000008 r8:00000000 r7:eced4808 r6:edbc9bac r5:eced4844
r4:eced4808
[<c022b7e8>] (warn_slowpath_null) from [<c0726f48>]
(__vb2_queue_cancel+0x174/0x1d8)
[<c0726dd4>] (__vb2_queue_cancel) from [<c0727648>]
(vb2_core_queue_release+0x20/0x40)
r10:ecc7bd70 r9:00000008 r8:00000000 r7:edb73010 r6:edbc9bac
r5:eced4844
r4:eced4808 r3:00000004
[<c0727628>] (vb2_core_queue_release) from [<c0729528>]
(vb2_queue_release+0x10/0x14)
r5:edbc9810 r4:eced4800
[<c0729518>] (vb2_queue_release) from [<c0724d08>]
(v4l2_m2m_ctx_release+0x1c/0x30)
[<c0724cec>] (v4l2_m2m_ctx_release) from [<bf0e8f28>]
(vpe_release+0x74/0xb0 [ti_vpe])
r5:edbc9810 r4:ed67a400
[<bf0e8eb4>] (vpe_release [ti_vpe]) from [<c070fccc>]
(v4l2_release+0x3c/0x80)
r7:edb73010 r6:ed176aa0 r5:edbc9868 r4:ed5119c0
[<c070fc90>] (v4l2_release) from [<c033cf1c>] (__fput+0x8c/0x1dc)
r5:ecc7bd70 r4:ed5119c0
[<c033ce90>] (__fput) from [<c033d0cc>] (____fput+0x10/0x14)
r10:00000000 r9:ed5119c0 r8:ece392d0 r7:c1059544 r6:ece38d80
r5:ece392b4
r4:00000000
[<c033d0bc>] (____fput) from [<c0246e00>] (task_work_run+0x98/0xb8)
[<c0246d68>] (task_work_run) from [<c022f1d8>] (do_exit+0x170/0xa80)
r9:ece351fc r8:00000000 r7:ecde3f58 r6:ffffe000 r5:ece351c0
r4:ece38d80
[<c022f068>] (do_exit) from [<c022fb6c>] (do_group_exit+0x48/0xc4)
r7:000000f8
[<c022fb24>] (do_group_exit) from [<c022fc00>]
(__wake_up_parent+0x0/0x28)
r7:000000f8 r6:b6c6a798 r5:00000001 r4:00000001
[<c022fbe8>] (SyS_exit_group) from [<c0207c80>]
(ret_fast_syscall+0x0/0x4c)
These warnings are caused by buffers which not properly cleaned
up/release during an abort use case.
In the abort cases the VPDMA desc buffers would still be mapped and the
in-flight VB2 buffers would not be released properly causing a kernel
warning from being generated by the videobuf2-core level.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(294): \
(int)g_sequence() < seq.last_seq + 1
fail: v4l2-test-buffers.cpp(740): \
buf.check(m2m_q, last_m2m_seq)
fail: v4l2-test-buffers.cpp(974): \
captureBufs(node, q, m2m_q, frame_count, true)
test MMAP: FAIL
The driver is failing to update the source frame sequence number in the
vb2 buffer object. Only the destination frame sequence was being
updated.
This is only a reporting issue if the user space app actually cares
about the frame sequence number. But it is fixed nonetheless.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(463): !pfmt.sizeimage
fail: v4l2-test-formats.cpp(736): \
Video Capture Multiplanar is valid, \
but TRY_FMT failed to return a format
test VIDIOC_TRY_FMT: FAIL
This failure is causd by the driver failing to handle out range
'bytesperline' values from user space applications.
VPDMA hardware is limited to 64k line stride (16 bytes aligned, so 65520
bytes). So make sure the provided or calculated 'bytesperline' is
smaller than the maximum value.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(672): \
Video Capture Multiplanar: TRY_FMT(G_FMT) != G_FMT
fail: v4l2-test-formats.cpp(672): \
Video Output Multiplanar: TRY_FMT(G_FMT) != G_FMT
...
test VIDIOC_TRY_FMT: FAIL
The default pixel format was setup as pointing to a specific offset in
the vpe_formats table assuming it was pointing to the V4L2_PIX_FMT_YUYV
entry. This became false after the addition on the NV21 format (see
above commid-id)
So instead of hard-coding an offset which might change over time we need
to use a lookup helper instead so we know the default will always be what
we intended.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Fixes: 40cc823f7005 ("media: ti-vpe: Add support for NV21 format")
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance warns with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(718): \
This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(719): \
http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
...
test VIDIOC_TRY_FMT: FAIL
We need to make sure that the returns a valid pixel format in all
instance. Based on the v4l2 framework convention drivers must return a
valid pixel format when the requested pixel format is either invalid or
not supported.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2-compliance fails with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
test VIDIOC_TRY_FMT: FAIL
This causes the following kernel panic:
Unable to handle kernel paging request at virtual address 56595561
pgd = ecd80e00
*pgd=00000000
Internal error: Oops: 205 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 930 Comm: v4l2-compliance Not tainted \
4.14.62-01715-gc8cd67f49a19 #1
Hardware name: Generic DRA72X (Flattened Device Tree)
task: ece44d80 task.stack: ecc6e000
PC is at __vpe_try_fmt+0x18c/0x2a8 [ti_vpe]
LR is at 0x8
Because the driver fails to properly check the 'num_planes' values for
proper ranges it ends up accessing out of bound data causing the kernel
panic.
Since this driver only handle single or dual plane pixel format, make
sure the provided value does not exceed 2 planes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VPE's max height supported MAX_H is set to 1184 which is the
padded height from VC1 decoder output.
In case of 90, 270 degree rotated video processing, input to
VPE will be 1080x1920, 720x1280 etc and MAX_H needs to be set
correct value. Setting MAX_H to 2048 as worst case height.
Signed-off-by: Ram Prasad <x0038811@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In NV21 format, the chroma plane is written to memory such that the U
and V components are swapped for NV12.
Create a new entry in the VPDMA formats to describe the correct data
types used in the data descriptors.
Update all checks for NV12 and add NV21 there as well.
Add support for V4L2_PIX_FMT_NV21 format for both capture and output
streams.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
SEQ_BT indicates the buffer for bottom field needs to be processed
before the top field.
Simplify the field selection logic to support SEQ_BT as well.
Modify the interlace flags to include any of alternate, SEQ_TB, SEQ_BT.
Update other format error checking to consider SEQ_BT.
Replace SEQ_TB with SEQ_XX wherever applicable.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of saving a pointer to the 'fh' member of struct vpe_ctx to
later have to use container_of to retrieve the actual pointer to the
context structure, which seems to confuse static code analysis tool
anyways, just save the pointer to the actual structure and then retrieve
it directly.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
commit 3dc2046ca7 ("[media] media: ti-vpe: vpe: allow use of user
specified stride") and commit da4414eaed ("[media] media: ti-vpe: vpdma:
add support for user specified stride") resulted in the Motion Vector
stride to be the same as the image stride.
This caused memory corruption in the output image as mentioned in
commit 00db969964 ("[media] media: ti-vpe: vpe: Fix line stride
for output motion vector").
Fixes: 3dc2046ca7 ("[media] media: ti-vpe: vpe: allow use of user specified stride")
Fixes: da4414eaed ("[media] media: ti-vpe: vpdma: add support for user specified stride")
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
