mac80211 limits amsdu size to the minimum of HT and VHT capabilities
but since in a VHT connection we don't transmit HT frames we can discard
HT limits.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change the UHB channels to start from 1 to match the specs (11ax Draft 5.0).
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We return in the if block, so it's unnecessary to have an else
statement. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the single antenna diversity support was sent upstream, only some
definitions were sent, due to a bad revert.
Fix this by adding the actual code.
Fixes: 5952e0ec3f ("iwlwifi: mvm: add support for single antenna diversity")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add new command for getting/setting current transmit power
and propagate requests from user space to firmware.
Signed-off-by: Mikhail Karpenko <mkarpenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Report MIC failure from firmware to cfg80211 subsystem
using dedicated callback cfg80211_michael_mic_failure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Send EAPOL frames via control path so they can be treated in a different
way rather than normal data frames. In this case EAPOLs are sent with
higher priority and with disabled aggregation and encryption. Besides,
all devices benefit from sending EAPOL frames via high priority path,
so move the functionality from chip specific to common code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx descriptors queue length is hardware specific. Current common default
value is no more than an accident. So move Rx descriptor queue setup to
platform PCIe backend in the same way as it is already done for Tx.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not attempt to print frequency for an invalid channel
provided by firmware. That channel may simply not exist.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix merge artifact for commit 0b68fe10b8 ("qtnfmac: modify debugfs
to support multiple cards") and finally add debugfs support
for multiple qtnfmac wireless cards.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
KASAN reported use-after-free error:
[ 995.220767] BUG: KASAN: use-after-free in qtnf_cmd_send_with_reply+0x169/0x3e0 [qtnfmac]
[ 995.221098] Read of size 2 at addr ffff888213d1ded0 by task kworker/1:1/71
The issue in qtnf_cmd_send_with_reply impacts all the commands that do
not need response other then return code. For such commands, consume_skb
is used for response skb and right after that return code in response
skb is accessed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A number of people have reported the Edimax EW-7611ULB works fine.
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 38506ecefa ("rtlwifi: rtl_pci: Start modification for
new drivers"), the flag that indicates that interrupts are enabled was
never set.
In addition, there are several places when enable/disable interrupts
were commented out are restored. A sychronize_interrupts() call is
removed.
Fixes: 38506ecefa ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 38506ecefa ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback needed to check if the hardware has released
a buffer indicating that a DMA operation is completed was not added.
Fixes: 38506ecefa ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 38506ecefa ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback to get the RX buffer address was added to
the PCI driver. Unfortunately, driver rtl8192de was not modified
appropriately and the code runs into a WARN_ONCE() call. The use
of an incorrect array is also fixed.
Fixes: 38506ecefa ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # 3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver could access a NULL firmware pointer if we don't
return here.
Fixes: 5195b90426 ("rtw88: avoid FW info flood")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This leak was found by testing the EDIMAX EW-7612 on Raspberry Pi 3B+ with
Linux 5.4-rc5 (multi_v7_defconfig + rtlwifi + kmemleak) and noticed a
single memory leak during probe:
unreferenced object 0xec13ee40 (size 176):
comm "kworker/u8:1", pid 36, jiffies 4294939321 (age 5580.790s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<fc1bbb3e>] __netdev_alloc_skb+0x9c/0x164
[<863dfa6e>] rtl92c_set_fw_rsvdpagepkt+0x254/0x340 [rtl8192c_common]
[<9572be0d>] rtl92cu_set_hw_reg+0xf48/0xfa4 [rtl8192cu]
[<116df4d8>] rtl_op_bss_info_changed+0x234/0x96c [rtlwifi]
[<8933575f>] ieee80211_bss_info_change_notify+0xb8/0x264 [mac80211]
[<d4061e86>] ieee80211_assoc_success+0x934/0x1798 [mac80211]
[<e55adb56>] ieee80211_rx_mgmt_assoc_resp+0x174/0x314 [mac80211]
[<5974629e>] ieee80211_sta_rx_queued_mgmt+0x3f4/0x7f0 [mac80211]
[<d91091c6>] ieee80211_iface_work+0x208/0x318 [mac80211]
[<ac5fcae4>] process_one_work+0x22c/0x564
[<f5e6d3b6>] worker_thread+0x44/0x5d8
[<82c7b073>] kthread+0x150/0x154
[<b43e1b7d>] ret_from_fork+0x14/0x2c
[<794dff30>] 0x0
It is because 8192cu doesn't implement usb_cmd_send_packet(), and this
patch just frees the skb within the function to resolve memleak problem
by now. Since 8192cu doesn't turn on fwctrl_lps that needs to download
command packet for firmware via the function, applying this patch doesn't
affect driver behavior.
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On 2019-10-28 06:07, wbob wrote:
> Hello Roman,
>
> while reading around drivers/net/wireless/ralink/rt2x00/rt2800lib.c
> I stumbled on what I think is an edit of yours made in error in march
> 2017:
>
> https://github.com/torvalds/linux/commit/41977e86#diff-dae5dc10da180f3b055809a48118e18aR5281
>
> RT6352 in line 5281 should not have been introduced as the "else if"
> below line 5291 can then not take effect for a RT6352 device. Another
> possibility is for line 5291 to be not for RT6352, but this seems
> very unlikely. Are you able to clarify still after this substantial time?
>
> 5277: static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
> ...
> 5279: } else if (rt2x00_rt(rt2x00dev, RT5390) ||
> 5280: rt2x00_rt(rt2x00dev, RT5392) ||
> 5281: rt2x00_rt(rt2x00dev, RT6352)) {
> ...
> 5291: } else if (rt2x00_rt(rt2x00dev, RT6352)) {
> ...
Hence remove errornous line 5281 to make the driver actually
execute the correct initialization routine for MT7620 chips.
As it was requested by Stanislaw Gruszka remove setting values of
MIMO_PS_CFG and TX_PIN_CFG. MIMO_PS_CFG is responsible for MIMO
power-safe mode (which is disabled), hence we can drop setting it.
TX_PIN_CFG is set correctly in other functions, and as setting this
value breaks some devices, rather don't set it here during init, but
only modify it later on.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Reported-by: wbob <wbob@jify.de>
Reported-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:83:17: warning: 'rtl8225sez2_tx_power_cck' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:79:17: warning: 'rtl8225sez2_tx_power_cck_A' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:75:17: warning: 'rtl8225sez2_tx_power_cck_B' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:71:17: warning: 'rtl8225sez2_tx_power_cck_ch14' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:62:17: warning: 'rtl8225se_tx_power_ofdm' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:53:17: warning: 'rtl8225se_tx_power_cck_ch14' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:44:17: warning: 'rtl8225se_tx_power_cck' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:40:17: warning: 'rtl8225se_tx_gain_cck_ofdm' defined but not used [-Wunused-const-variable=]
They are never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:841:7: warning: variable free_pdu set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:30: warning: variable tx_rts_count set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:6: warning: variable tx_rts set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:843:7: warning: variable totlen set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The LPS threshold was set to 2, means driver will leave LPS
mode if there is more than 2 frames TX/RX for every 2 seconds.
This makes driver enter/leave LPS frequently even if we just
"ping -i1" to the others.
Apparently we do not want to leave LPS mode if there is only
some background traffics or web surfing. By experiment, set
this to 50 is a more reasonable value to lower the over all
power consumption.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
local variable "ret" is not used. hence it is safe to remove and
just return 0.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
local variable "rc" is not used. It is safe to remove and
There is only one caller of libipw_qos_convert_ac_to_parameters().
hence make it void
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdwYyqAAoJEG4XJFUm622b/jMH/0KUcGz8y4gkk2B2lMRyUOTu
t84LiSHxcsq6letlr/vak4S6NrxMLP8Z/ByyoKC8o3yeVsdyMNMSLZAztFFhxdXr
Haky2SM10q6vnn9s1skXS/qkHSd2WdUFT2DgYxyOPCtJUazVKjcboJ4YX/TUg99a
5eqPpZ4RXtW6uOmWHS7JXtLcCFPywKPBtMAjLEDMYOUSSBWExBNyNZNhznSS3ywY
4VKvc675gXE+WD3qXRhL8EJjyed94yuS3wYbKWp8iTaIRyluDmc5lVhjWH1A0HLE
Qb62QL8XLtbX5fcTnaupdAIXwxeIBylOBe8QtW7QUbAnGFf8bexLxfnQM+To4wI=
=24zD
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ThinkPad Thunderbolt 3 Dock Gen 2 is another docking station that uses
RTL8153 based USB ethernet.
The device supports macpassthru, but it failed to pass the test of -AD,
-BND and -BD. Simply bypass these tests since the device supports this
feature just fine.
Also the ACPI objects have some differences between Dell's and Lenovo's,
so make those ACPI infos no longer hardcoded.
BugLink: https://bugs.launchpad.net/bugs/1827961
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements reset_prepare and reset_done, which are used
for handling FLR.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new FW has added extra validation for HSI version to
make FW backward compatible with older VF drivers. Hence
set fp_hsi_ver to Fast Path HSI version of the FW in use.
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF driver doesn't enable tx-switching for all cos queues/clients,
which causes packets drop from PF to VF. Fix this by enabling
tx-switching on all cos queues/clients.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW version 7.13.15 addresses the issue in Multi-cos implementation.
This patch re-enables the Multi-Cos support in the driver.
Fixes: d1f0b5dce8 ("bnx2x: Disable multi-cos feature.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 97a27d6d6e8d "bnx2x: Add FW 7.13.15.0" added said .bin FW to
linux-firmware tree. This FW addresses few important issues in the earlier
FW release.
This patch incorporates FW 7.13.15.0 in the bnx2x driver.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a phy_interface_t to of_get_phy_mode(), by changing the type of
phy_mode in the device structure. This then requires that
zmii_attach() is also changes, since it takes a pointer to phy_mode.
Fixes: 0c65b2b90d ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU can report how many entries it contains. It does this per bin,
there being 4 bins in total. Export the ATU as a devlink resource, and
provide a method the needed callback to get the resource occupancy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When retrieving the ATU statistics, and ATU get next has to be
performed to trigger the ATU to collect the statistics. Export a
helper from global1_atu to perform this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each supported switch, add an entry to the info structure for the
number of MACs which can be stored in the ATU. This will later be used
to export the ATU as a devlink resource, and indicate its occupancy,
how full the ATU is.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grab an optional and exclusive reset controller line for the switch and
manage it during probe/remove functions accordingly. For 7278 devices we
change bcm_sf2_sw_rst() to use the reset controller line since the
WATCHDOG_CTRL register does not reset the switch contrary to stated
documentation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macros HCLGE_MPF_ENBALE and HCLGEVF_MPF_ENBALE are defined but never
used. I was going to fix the spelling mistake "ENBALE" -> "ENABLE" but
found these macros are not used, so they can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since RSS hash is available from the host, record it in
the skb.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver needs to create a hash value because it
was not done at higher level, then the hash should be marked
as a software not hardware hash.
Fixes: f72860afa2 ("hv_netvsc: Exclude non-TCP port numbers from vRSS hashing")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-11-04
This series contains updates to the ice driver only.
Anirudh refactors the code to reduce the kernel configuration flags and
introduces ice_base.c file.
Maciej does additional refactoring on the configuring of transmit
rings so that we are not configuring per each traffic class flow.
Added support for XDP in the ice driver. Provides additional
re-organizing of the code in preparation for adding build_skb() support
in the driver. Adjusted the computational padding logic for headroom
and tailroom to better support build_skb(), which also aligns with the
logic in other Intel LAN drivers. Added build_skb support and make use
of the XDP's data_meta.
Krzysztof refactors the driver to prepare for AF_XDP support in the
driver and then adds support for AF_XDP.
v2: Updated patch 3 of the series based on community feedback with the
following changes...
- return -EOPNOTSUPP instead of ENOTSUPP for too large MTU which makes
it impossible to attach XDP prog
- don't check for case when there's no XDP prog currently on interface
and ice_xdp() is called with NULL bpf_prog; this happens when user
does "ip link set eth0 xdp off" and no prog is present on VSI; no need
for that as it is handled by higher layer
- drop the extack message for unknown xdp->command
- use the smp_processor_id() for accessing the XDP Tx ring for XDP_TX
action
- don't leave the interface in downed state in case of any failure
during the XDP Tx resources handling
- undo rename of ice_build_ctob
The above changes caused a ripple effect in patches 4 & 5 to update
references to ice_build_ctob() which are now build_ctob()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2019-11-04
This series contains old Halloween candy updates, yet still sweet, to
fm10k, ixgbe and i40e.
Jake adds the missing initializers for a couple of the TLV attribute
macros. Added support for capturing and reporting statistics for all of
the VFs in a given PF. Lastly, bump the version of the fm10k driver to
reflect the recent changes.
Alex addresses locality issues in the ixgbe driver when it is loaded on
a system supporting multiple NUMA nodes.
Manjunath Patil provides changes to the ixgbe driver, similar to those
made to igb, to prevent transmit packets to request a hardware timestamp
when the NIC has not been setup via the SIOCSHWTSTAMP ioctl.
Alice adds support for x710 by adding the missing device id's in the
appropriate places to ensure all the features are enabled in i40e.
Jesse adds support for VF stats gathering in the i40e via the kernel
via ndo_get_vf_stats function.
v2: Fixed up commit id references in patch 5's description to align with
how commit id's should be referenced.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the VF stats gathering via the kernel via ndo_get_vf_stats().
The driver will show per-VF stats in the output of the command:
ip -s link show dev <PF>
Testing Hints:
ip -s link show dev eth0
will return non-zero VF stats.
...
vf 0 MAC 00:55:aa:00:55:aa, spoof checking on, link-state enable, trust off
RX: bytes packets mcast bcast
128000 1000 104 104
TX: bytes packets
128000 1000
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I40E_DEV_ID_10G_BASE_T_BC device id was added previously,
but was not enabled in all the appropriate places. Adding it
to enable it's use.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
HW timestamping can only be requested for a packet if the NIC is first
setup via ioctl(SIOCSHWTSTAMP). If this step was skipped, then the ixgbe
driver still allowed TX packets to request HW timestamping. In this
situation, we see 'clearing Tx Timestamp hang' noise in the log.
Fix this by checking that the NIC is configured for HW TX timestamping
before accepting a HW TX timestamping request.
Similar-to:
commit 26bd4e2db0 ("igb: protect TX timestamping from API misuse")
commit 0a6f2f05a2 ("igb: Fix a test with HWTSTAMP_TX_ON")
Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An upcoming out-of-tree release will be occurring which will include the
recent functionality to support virtual function statistics. Update the
kernel driver version to match this.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to address locality issues present in the ixgbe driver
when it is loaded on a system supporting multiple NUMA nodes and more CPUs
then the device can map in a 1:1 fashion. Instead of just arbitrarily
mapping itself to CPUs 0-62 it would make much more sense to map itself to
the local CPUs first, and then map itself to any remaining CPUs that might
be used.
The first effect of this is that queue 0 should always be allocated on the
local CPU/NUMA node. This is important as it is the default destination if
a packet doesn't match any existing flow director filter or RSS rule and as
such having it local should help to reduce QPI cross-talk in the event of
an unrecognized traffic type.
In addition this should increase the likelihood of the RSS queues being
allocated and used on CPUs local to the device while the ATR/Flow Director
queues would be able to route traffic directly to the CPU that is likely to
be processing it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Support capturing and reporting statistics for all of the VFs associated
with a given PF device via the ndo_get_vf_stats callback.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the missing field initializers for a couple of the TLV attribute
macros. This resolves the last few -Wmissing-field-initializers warnings
for the fm10k Linux driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
