In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, user space gets the old AP in scan
results (cached). User space may decide to roam to that old AP
which will cause a disconnection and longer recovery.
Remove APs that are probably out of range from BSS table.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regular RX path has a lot of code, but with a few
assumptions on the hardware it's possible to reduce the
amount of code significantly. Currently the assumptions
on the driver are the following:
* hardware/driver reordering buffer (if supporting aggregation)
* hardware/driver decryption & PN checking (if using encryption)
* hardware/driver did de-duplication
* hardware/driver did A-MSDU deaggregation
* AP_LINK_PS is used (in AP mode)
* no client powersave handling in mac80211 (in client mode)
of which some are actually checked per packet:
* de-duplication
* PN checking
* decryption
and additionally packets must
* not be A-MSDU (have been deaggregated by driver/device)
* be data packets
* not be fragmented
* be unicast
* have RFC 1042 header
Additionally dynamically we assume:
* no encryption or CCMP/GCMP, TKIP/WEP/other not allowed
* station must be authorized
* 4-addr format not enabled
Some data needed for the RX path is cached in a new per-station
"fast_rx" structure, so that we only need to look at this and
the packet, no other memory when processing packets on the fast
RX path.
After doing the above per-packet checks, the data path collapses
down to a pretty simple conversion function taking advantage of
the data cached in the small fast_rx struct.
This should speed up the RX processing, and will make it easier
to reason about parallelizing RX (for which statistics will need
to be per-CPU still.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the likely case that probe_count is 0, don't write to the
memory there.
Also use ifmgd consistently in the function, instead of using
sdata->u.mgd as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may need to track which vif is using VHT MU-MIMO.
Move the flag indicationg the ownership of MU_MIMO to
ieee80211_vif.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make sure there's at least a debug message whenever the
connection to the AP is terminated.
Also change one message from wiphy_debug() to the common
mlme_dbg().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The station MLME and IBSS/mesh ones use entirely different
code for interpreting HT and VHT operation elements. Change
the code that interprets them a bit - it now modifies an
existing chandef - and use it also in the MLME code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During a sw scan ieee80211_iface_work ignores work items for all vifs.
However after the scan complete work is requeued only for STA, ADHOC
and MESH iftypes.
This occasionally results in event processing getting delayed/not
processed for iftype AP when it coexists with a STA. This can result
in data halt and eventually disconnection on the AP interface.
Cc: stable@vger.kernel.org
Signed-off-by: Sachin Kulkarni <Sachin.Kulkarni@imgtec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use to_delayed_work() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Group ID Management frame is an Action frame of
category VHT. It is transmitted by the AP to assign
or change the user position of a STA for one or more
group IDs.
Process and save the group membership data. Notify
underlying driver of changes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
An AP can send an operating channel width change in a beacon
opmode notification IE as long as there's a change in the nss as
well (See 802.11ac-2013 section 10.41).
So don't limit updating to nss only from an opmode notification IE.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AP is advertising limited TX power, the message can be
printed over and over again. Suppress it when the power level
isn't changing.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=106011
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new VIF flag, that will allow get NOA update
notification when driver will request this, even
this is not pure P2P vif (eg. STA vif).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As WMM is required for HT/VHT operation, treat bad WMM parameters
more gracefully by falling back to default parameters instead of
not using WMM assocation. This makes it possible to still use HT
or VHT, although potentially with reduced quality of service due
to unintended WMM parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disabling WMM has a huge impact these days. It implies that
HT and VHT will be disabled which means that the throughput
will be drammatically reduced.
Since the AIFSN is a transmission parameter, we can play a
bit and fix it up to make it compliant with the 802.11
specification which requires it to be at least 2.
Increasing it from 1 to 2 will slightly reduce the
likelyhood to get a transmission opportunity compared to
other clients that would accept to set AIFSN=1, but at
least it will allow HT and VHT which is a huge gain.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function currently determines this value, for use in bss_info.qos,
based on the interface type itself. Make it a parameter instead and
set it with the same logic for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Local request to deauthenticate wasn't handled while associating, thus
the association could continue even when the user space required to
disconnect.
Cc: stable@vger.kernel.org
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's little point in keeping (and even sending to userspace)
the beacon_loss_count value per station, since it can only apply
to the AP on a managed-mode connection. Move the value to ifmgd,
advertise it only in managed mode, and remove it from ethtool as
it's available through better interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As this API has never really seen any use and most drivers don't
ever use the value derived from it, remove it.
Change the only driver using it (rt2x00) to simply use the DTIM
period instead of the "max sleep" time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 5c48f12017.
Some device drivers (ath10k) offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
-----BEGIN PGP SIGNATURE-----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=BF9F
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the current cycle, we have the following right now:
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of int with 0/1, use bool with false/true for the
powersave argument to ieee80211_send_nullfunc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of nesting two if statements, inline the second
check into the first if statement and to indentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It doesn't seem problematic to change the weight for the average
beacon signal from 3 to 4, so use DECLARE_EWMA. This also makes
the code easier to maintain since bugs like the one fixed in the
previous patch can't happen as easily.
With a fix from Avraham Stern to invert the sign since EMWA uses
unsigned values only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ifmgd->ave_beacon_signal value cannot be taken as is for
comparisons, it must be divided by since it's represented
like that for better accuracy of the EWMA calculations. This
would lead to invalid driver RSSI events. Fix the used value.
Fixes: 615f7b9bb1 ("mac80211: add driver RSSI threshold events")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These file aren't really useful:
- if per beacon data is required then you need to use
radiotap or similar anyway, debugfs won't help much
- average beacon signal is reported in station info in
nl80211 and can be looked up with iw
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The direct probe step before authentication was done mostly for
two reasons:
1) the BSS data could be stale
2) the beacon might not have included all IEs
The concern (1) doesn't really seem to be relevant any more as
we time out BSS information after about 30 seconds, and in fact
the original patch only did the direct probe if the data was
older than the BSS timeout to begin with. This condition got
(likely inadvertedly) removed later though.
Analysing this in more detail shows that since we mostly use
data from the association response, the only real reason for
needing the probe response was that the code validates the WMM
parameters, and those are optional in beacons. As the previous
patches removed that behaviour, we can now remove the direct
probe step entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently if 80MHz channels are not allowed for use, the VHT IE is not
included in the probe request for an AP. This is not good enough if the
AP is configured with the wrong regulatory and supports VHT even where
prohibited or in TDLS scenarios.
Mark the ifmgd with the DISABLE_VHT flag for the misbehaving-AP case, and
unset VHT support from the peer-station entry for the TDLS case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for declaring MU-MIMO beamformee capability for
relevant hardware.
When sending association request, the capability is included if both
hardware and the AP support it, and no other virtual interface
is using it.
This is in order to avoid multiple interfaces using MU-MIMO in parallel
which might lead to contradictions in the group-id mechanism.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IEEE802.11-2012 specification is vague regarding SMPS operation during
TDLS. It does not define a clear way to transition between SMPS states.
To avoid interop issues, set SMPS to off when TDLS peers are connected.
Accomplish this by extending the definition of the AUTOMATIC state. If the
driver forces a state other than OFF, disconnect all TDLS peers.
While at it, avoid changing the SMPS state of the peer STA. We have no
way to control it, so try and behave correctly towards it.
Move the TDLS peer-teardown function to where the rest of the TDLS code
resides.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There were a few rare cases when upon
authentication failure channel wasn't released.
This could cause stale pointers to remain in
chanctx assigned_vifs after interface removal and
trigger general protection fault later.
This could be triggered, e.g. on ath10k with the
following steps:
1. start an AP
2. create 2 extra vifs on ath10k host
3. connect vif1 to the AP
4. connect vif2 to the AP
(auth fails because ath10k firmware isn't able
to maintain 2 peers with colliding AP mac
addresses across vifs and consequently
refuses sta_info_insert() in
ieee80211_prep_connection())
5. remove the 2 extra vifs
6. goto step 2; at step 3 kernel was crashing:
general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: ath10k_pci ath10k_core ath
...
Call Trace:
[<ffffffff81a2dabb>] ieee80211_check_combinations+0x22b/0x290
[<ffffffff819fb825>] ? ieee80211_check_concurrent_iface+0x125/0x220
[<ffffffff8180f664>] ? netpoll_poll_disable+0x84/0x100
[<ffffffff819fb833>] ieee80211_check_concurrent_iface+0x133/0x220
[<ffffffff81a0029e>] ieee80211_open+0x3e/0x80
[<ffffffff817f2d26>] __dev_open+0xb6/0x130
[<ffffffff817f3051>] __dev_change_flags+0xa1/0x170
...
RIP [<ffffffff81a23140>] ieee80211_chanctx_radar_detect+0xa0/0x170
(gdb) l * ieee80211_chanctx_radar_detect+0xa0
0xffffffff81a23140 is in ieee80211_chanctx_radar_detect (/devel/src/linux/net/mac80211/util.c:3182).
3177 */
3178 WARN_ON(ctx->replace_state == IEEE80211_CHANCTX_REPLACES_OTHER &&
3179 !list_empty(&ctx->assigned_vifs));
3180
3181 list_for_each_entry(sdata, &ctx->assigned_vifs, assigned_chanctx_list)
3182 if (sdata->radar_required)
3183 radar_detect |= BIT(sdata->vif.bss_conf.chandef.width);
3184
3185 return radar_detect;
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no drivers setting IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE
or IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE, so any code using the
two flags is dead; it's also exceedingly unlikely that any new driver
could ever need to set these flags.
The wcn36xx code is almost certainly broken, but this preserves the
previous behaviour.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When trying to associate, the AP could send a deauth frame instead.
Currently mac80211 drops that frame and doesn't report it to the
supplicant, which, in some versions and/or in certain circumstances
will simply keep trying to associate over and over again instead of
trying authentication again.
Fix this by reacting to deauth frames while associating, reporting
them to the supplicant and dropping the association attempt (which
is bound to fail.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a station does a channel switch, it's not well defined what its TDLS
peers would do. Avoid a situation when the local side marks a potentially
disconnected peer as a TDLS peer.
Keeping peers connected through CSA is doubly problematic with the upcoming
TDLS WIDER-BW feature which allows peers to widen the BSS channel. The
new channel transitioned-to might not be compatible and would require
a re-negotiation anyway.
Make sure to disallow new TDLS link during CSA.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HT and VHT override configurations were ignored during association and
applied only when first beacon recived, or not applied at all.
Fix the code to apply HT/VHT overrides during association. This is a bit
tricky since the channel was already configured during authentication
and we don't want to reconfigure it unless there's really a change.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This changes a couple of messages from sdata_info to sdata_dbg.
This should reduce some log spam, as reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=1206468
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
-----BEGIN PGP SIGNATURE-----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=O/cf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicating just the peer's capability is fairly pointless
if the local device doesn't support it. Make the variable
track both combined, and remove the 'local support' check
in the TX path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Louis reported that a static checker was complaining that
the 'dst' variable was set (multiple times) but not used.
This is due to a previous commit having removed the usage
(apparently erroneously), so add it back.
Fixes: a344d6778a ("mac80211: allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR")
Reported-by: Louis Langholtz <lou_langholtz@me.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stop scan before authentication or association to make sure
that nothing interferes with connection flow.
Currently mac80211 defers RX auth and assoc packets (among other ones)
until after the scan is complete, so auth during scan is likely to fail
if scan took too much time.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the reason
of the deauth.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the
success / failure of the association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the
success / failure of the authentication.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will be able to add more events, such as MLME events and
others. The low level driver may be interested in knowing
about these events to dump firmware data upon failures, or
to change parameters in case connection attempts fail etc...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the AP is confused and starts doing a CSA to the same channel,
just ignore that request instead of trying to act it out since it
was likely sent in error anyway.
In the case of the bug I was investigating the GO was misbehaving
and sending out a beacon with CSA IEs still included after having
actually done the channel switch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
