We switched this code from spin_lock_bh() to vanilla spin_lock() but
there was one stray spin_unlock_bh() that was overlooked. This
patch converts it to spin_unlock() as well.
Fixes: d8570d018f ("dmaengine: at_xdmac: move spin_lock_bh to spin_lock in tasklet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The overflow error flag (ROI: Request Overflow Error) is only relevant
for the case when the channel handles a peripheral synchronized transfer.
Not in the case of memory to memory transfer where there is no hardware
request signal.
Remove the use of this interrupt source in such a case. It's based on
the first descriptor which holds the configuration for the whole
linked list transfer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Complement the identification of errors with stopping the channel and
dumping the descriptor that led to the error case.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Even if this case shouldn't happen when controller is properly programmed,
it's still better to avoid dumping a kernel Oops for this.
As the sequence may happen only for debugging purposes, log the error and
just finish the tasklet call.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
atchan->status variable is used to store two different information:
- pass channel interrupts status from interrupt handler to tasklet;
- channel information like whether it is cyclic or paused;
This causes a bug when device_terminate_all() is called,
(AT_XDMAC_CHAN_IS_CYCLIC cleared on atchan->status) and then a late End
of Block interrupt arrives (AT_XDMAC_CIS_BIS), which sets bit 0 of
atchan->status. Bit 0 is also used for AT_XDMAC_CHAN_IS_CYCLIC, so when
a new descriptor for a cyclic transfer is created, the driver reports
the channel as in use:
if (test_and_set_bit(AT_XDMAC_CHAN_IS_CYCLIC, &atchan->status)) {
dev_err(chan2dev(chan), "channel currently used\n");
return NULL;
}
This patch fixes the bug by adding a different struct member to keep
the interrupts status separated from the channel status bits.
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
as you are already in a tasklet, it is unnecessary to call spin_lock_bh.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Despite the efforts made to correctly read the NDA and CUBC registers,
the order in which the registers are read could sometimes lead to an
inconsistent state.
Re-using the timeline from the comments, this following timing of
registers reads could lead to reading NDA with value "@desc2" and
CUBC with value "MAX desc1":
INITD -------- ------------
|____________________|
_______________________ _______________
NDA @desc2 \/ @desc3
_______________________/\_______________
__________ ___________ _______________
CUBC 0 \/ MAX desc1 \/ MAX desc2
__________/\___________/\_______________
| | | |
Events:(1)(2) (3)(4)
(1) check_nda = @desc2
(2) initd = 1
(3) cur_ubc = MAX desc1
(4) cur_nda = @desc2
This is allowed by the condition ((check_nda == cur_nda) && initd),
despite cur_ubc and cur_nda being in the precise state we don't want.
This error leads to incorrect residue computation.
Fix it by inversing the order in which CUBC and INITD are read. This
makes sure that NDA and CUBC are always read together either _before_
INITD goes to 0 or _after_ it is back at 1.
The case where NDA is read before INITD is at 0 and CUBC is read after
INITD is back at 1 will be rejected by check_nda and cur_nda being
different.
Fixes: 53398f4888 ("dmaengine: at_xdmac: fix residue corruption")
Cc: stable@vger.kernel.org
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Replace '%d' by '%zu' to fix the compilation warning:-
"format ‘%d’ expects argument of type ‘int’,but argument has type ‘size_t’ [-Wformat=]"
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
save_gs is supposed to save the channel status in order to be restored at
resume time but it is never updated and is always 0. Anyway, the channel
status is updated in the per channel loop later in the resume function.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We should use dma_pool_zalloc instead of dma_pool_alloc/memset.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of dmaenegine to
register a callback_result which tells them the result of the dma
transaction. Right now only one user ntb is using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no place in
kernel, this also remove NO_IRQ from dmaengine subsystem (both arm and
ppc users)
- Support for IOMMU slave transfers and it implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of driver,
and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9iA3
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of
dmaenegine to register a callback_result which tells them the
result of the dma transaction. Right now only one user (ntb) is
using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no
place in kernel, this also remove NO_IRQ from dmaengine subsystem
(both arm and ppc users)
- Support for IOMMU slave transfers and its implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of
driver, and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers"
* tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (169 commits)
async_pq_val: fix DMA memory leak
dmaengine: virt-dma: move function declarations
dmaengine: omap-dma: Enable burst and data pack for SG
DT: dmaengine: rcar-dmac: document R8A7743/5 support
dmaengine: fsldma: Unmap region obtained by of_iomap
dmaengine: jz4780: fix resource leaks on error exit return
dma-debug: fix ia64 build, use PHYS_PFN
dmaengine: coh901318: fix integer overflow when shifting more than 32 places
dmaengine: edma: avoid uninitialized variable use
dma-mapping: fix m32r build warning
dma-mapping: fix ia64 build, use PHYS_PFN
dmaengine: ti-dma-crossbar: enable COMPILE_TEST
dmaengine: omap-dma: enable COMPILE_TEST
dmaengine: edma: enable COMPILE_TEST
dmaengine: ti-dma-crossbar: Fix of_device_id data parameter usage
dmaengine: ti-dma-crossbar: Correct type for of_find_property() third parameter
dmaengine/ARM: omap-dma: Fix the DMAengine compile test on non OMAP configs
dmaengine: edma: Rename set_bits and remove unused clear_bits helper
dmaengine: edma: Use correct type for of_find_property() third parameter
dmaengine: edma: Fix of_device_id data parameter usage (legacy vs TPCC)
...
free_irq() expects the same device identity that was passed to
corresponding request_irq(), otherwise the IRQ is not freed.
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is in preperation of moving to a callback that provides results to the
callback for the transaction. The conversion will maintain current behavior
and the driver must convert to new callback mechanism at a later time in
order to receive results.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time we have bit of largish changes:
New drivers:
- Xilinx zynqmp dma engine driver.
- Marvell xor2 driver.
Updates:
- dmatest sg support.
- updates and enhancements to Xilinx drivers, adding of cyclic mode.
- clock handling fixes across drivers.
- removal of OOM messages on kzalloc across subsystem.
- interleaved transfers support in omap driver.
- runtime pm support in qcom bam dma.
- tasklet kill freeup across drivers.
- irq cleanup on remove across drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tYp0
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.8-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have bit of largish changes: two new drivers, bunch of
updates and cleanups to existing set. Nothing super exciting though.
New drivers:
- Xilinx zynqmp dma engine driver
- Marvell xor2 driver
Updates:
- dmatest sg support
- updates and enhancements to Xilinx drivers, adding of cyclic mode
- clock handling fixes across drivers
- removal of OOM messages on kzalloc across subsystem
- interleaved transfers support in omap driver
- runtime pm support in qcom bam dma
- tasklet kill freeup across drivers
- irq cleanup on remove across drivers"
* tag 'dmaengine-4.8-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (94 commits)
dmaengine: k3dma: add missing clk_disable_unprepare() on error in k3_dma_probe()
dmaengine: zynqmp_dma: add missing MODULE_LICENSE
dmaengine: qcom_hidma: use for_each_matching_node() macro
dmaengine: zynqmp_dma: Fix static checker warning
dmaengine: omap-dma: Support for interleaved transfer
dmaengine: ioat: statify symbol
dmaengine: pxa_dma: implement device_synchronize
dmaengine: imx-sdma: remove assignment never used
dmaengine: imx-sdma: remove dummy assignment
dmaengine: cppi: remove unused and bogus check
dmaengine: qcom_hidma_lli: kill the tasklets upon exit
dmaengine: pxa_dma: remove owner assignment
dmaengine: fsl_raid: remove owner assignment
dmaengine: coh901318: remove owner assignment
dmaengine: qcom_hidma: kill the tasklets upon exit
dmaengine: txx9dmac: explicitly freeup irq
dmaengine: sirf-dma: kill the tasklets upon exit
dmaengine: s3c24xx: kill the tasklets upon exit
dmaengine: s3c24xx: explicitly freeup irq
dmaengine: pl330: explicitly freeup irq
...
mbr_ds is an integer, don't use %pad to print it.
Fixes: commit 268914f4e7 ("dmaengine: at_xdmac: use %pad format string for dma_addr_t")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The at_xdmac_init_used_desc() and at_xdmac_prep_dma_memset()
functions are not exported outside the driver, so make them
static to avoid the following warnings:
drivers/dma/at_xdmac.c:459:6: warning: symbol 'at_xdmac_init_used_desc' was not declared. Should it be static?
drivers/dma/at_xdmac.c:1205:32: warning: symbol 'at_xdmac_prep_dma_memset' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Due to the way CUBC register is updated, a double flush is needed to
compute an accurate residue. First flush aim is to get data from the DMA
FIFO and second one ensures that we won't report data which are not in
memory.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #v4.1 and later
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
An unexpected value of CUBC can lead to a corrupted residue. A more
complex sequence is needed to detect an inaccurate value for NCA or CUBC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #v4.1 and later
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Having descriptors aligned on 64 bits allows update CNDA and CUBC in an
atomic way.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #v4.1 and later
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When computing the residue we need two pieces of information: the current
descriptor and the remaining data of the current descriptor. To get
that information, we need to read consecutively two registers but we
can't do it in an atomic way. For that reason, we have to check manually
that current descriptor has not changed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Suggested-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reported-by: David Engraf <david.engraf@sysgo.com>
Tested-by: David Engraf <david.engraf@sysgo.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Few fixes on drivers have piled up and one missed rcar bindings patch
which got somehow lost in for-linus branch so cherry-picked that one
Fixes are on dw, at_hdmac, edma
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=16UM
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Here is my second pull request for this window:
A few driver fixes have piled up and one missed rcar bindings patch
which got somehow lost in for-linus branch so cherry-picked that one.
Fixes are for dw, at_hdmac, edma"
* tag 'dmaengine-fix-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: rcar-dmac: Document SoC specific bindings
dmaengine: at_xdmac: fix resume for cyclic transfers
dmaengine: dw: fix cyclic transfer callbacks
dmaengine: dw: fix cyclic transfer setup
dmaengine: edma: Fix paRAM slot allocation for entry channel 0
When having cyclic transfers, the channel was paused when performing
suspend but was not correctly resumed.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: <stable@vger.kernel.org> # 4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This round we have few new features, new driver and updates to few drivers.
The new features to dmaengine core are:
- Synchronized transfer termination API to terminate the dmaengine
transfers in synchronized and async fashion as required by users.
We have its user now in ALSA dmaengine lib, img, at_xdma, axi_dmac
drivers.
- Universal API for channel request and start consolidation of request
flows. It's user is ompa-dma driver.
- Introduce reuse of descriptors and use in pxa_dma driver
Add/Remove:
- STM32 DMA driver
- Removal of unused R-Car HPB-DMAC driver
Updates:
- ti-dma-crossbar updates for supporting eDMA
- tegra-apb pm updates
- idma64
- mv_xor updates
- ste_dma updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D5Fb
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This round we have few new features, new driver and updates to few
drivers.
The new features to dmaengine core are:
- Synchronized transfer termination API to terminate the dmaengine
transfers in synchronized and async fashion as required by users.
We have its user now in ALSA dmaengine lib, img, at_xdma, axi_dmac
drivers.
- Universal API for channel request and start consolidation of
request flows. It's user is ompa-dma driver.
- Introduce reuse of descriptors and use in pxa_dma driver
Add/Remove:
- New STM32 DMA driver
- Removal of unused R-Car HPB-DMAC driver
Updates:
- ti-dma-crossbar updates for supporting eDMA
- tegra-apb pm updates
- idma64
- mv_xor updates
- ste_dma updates"
* tag 'dmaengine-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (54 commits)
dmaengine: mv_xor: add suspend/resume support
dmaengine: mv_xor: de-duplicate mv_chan_set_mode*()
dmaengine: mv_xor: remove mv_xor_chan->current_type field
dmaengine: omap-dma: Add support for DMA filter mapping to slave devices
dmaengine: edma: Add support for DMA filter mapping to slave devices
dmaengine: core: Introduce new, universal API to request a channel
dmaengine: core: Move and merge the code paths using private_candidate
dmaengine: core: Skip mask matching when it is not provided to private_candidate
dmaengine: mdc: Correct terminate_all handling
dmaengine: edma: Add probe callback to edma_tptc_driver
dmaengine: dw: fix potential memory leak in dw_dma_parse_dt()
dmaengine: stm32-dma: Fix unchecked deference of chan->desc
dmaengine: sh: Remove unused R-Car HPB-DMAC driver
dmaengine: usb-dmac: Document SoC specific compatibility strings
ste_dma40: Delete an unnecessary variable initialisation in d40_probe()
ste_dma40: Delete another unnecessary check in d40_probe()
ste_dma40: Delete an unnecessary check before the function call "kmem_cache_destroy"
dmaengine: tegra-apb: Free interrupts before killing tasklets
dmaengine: tegra-apb: Update driver to use GFP_NOWAIT
dmaengine: tegra-apb: Only save channel state for those in use
...
This patch fixes at_xdmac_prep_dma_memcpy(). Indeed the data width field
of the Channel Configuration register was not updated properly in the
loop: the bits of the dwidth field were not cleared before adding their
new value.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When performing interleaved transfers with numf > 1, an extra line is
copied. The mbr.bc field is incremented once too often. The length of
the block is (BLEN+1) microblocks.
Signed-off-by: Sylvain ETIENNE <Sylvain.ETIENNE@ingenico.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 4e5385784e ("dmaengine: at_xdmac: handle numf > 1")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code was not in agreement with the comments.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.3 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix typo in a macro which was not used until now. It explains why there
is no error at compilation time.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 "dmaengine: at_xdmac: creation of the atmel eXtended
DMA Controller driver"
Cc: stable@vger.kernel.org # 3.19 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When setting the channel configuration register, the perid field is not
set to 0 since it is useless for mem2mem transfers. Unfortunately, a
device has 0 as perid. It could cause spurious flags status because
the controller could mix some events from the two channels.
For that reason, use the highest perid value for mem2mem transfers since it
doesn't match the perid of other devices.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_addr_t may be defined as 32 or 64 bit depending on configuration,
so it cannot be printed using the normal format strings, as
gcc correctly warns:
drivers/dma/at_xdmac.c: In function 'at_xdmac_interleaved_queue_desc':
drivers/dma/at_xdmac.c:922:51: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
This changes the format strings to use the special "%pad" format
string that prints a dma_addr_t, and changes the arguments so we
pass the address by reference as required.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time we have a very typical update which is mostly fixes and updates to
drivers and no new drivers.
- Biggest change is coming from Peter for edma cleanup which even caused
some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tIzO
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have a very typical update which is mostly fixes and
updates to drivers and no new drivers.
- the biggest change is coming from Peter for edma cleanup which even
caused some last minute regression, things seem settled now
- idma64 and dw updates
- iotdma updates
- module autoload fixes for various drivers
- scatter gather support for hdmac"
* tag 'dmaengine-4.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (77 commits)
dmaengine: edma: Add dummy driver skeleton for edma3-tptc
Revert "ARM: DTS: am33xx: Use the new DT bindings for the eDMA3"
Revert "ARM: DTS: am437x: Use the new DT bindings for the eDMA3"
dmaengine: dw: some Intel devices has no memcpy support
dmaengine: dw: platform: provide platform data for Intel
dmaengine: dw: don't override platform data with autocfg
dmaengine: hdmac: Add scatter-gathered memset support
dmaengine: hdmac: factorise memset descriptor allocation
dmaengine: virt-dma: Fix kernel-doc annotations
ARM: DTS: am437x: Use the new DT bindings for the eDMA3
ARM: DTS: am33xx: Use the new DT bindings for the eDMA3
dmaengine: edma: New device tree binding
dmaengine: Kconfig: edma: Select TI_DMA_CROSSBAR in case of ARCH_OMAP
dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx
dmaengine: edma: Merge the of parsing functions
dmaengine: edma: Do not allocate memory for edma_rsv_info in case of DT boot
dmaengine: edma: Refactor the dma device and channel struct initialization
dmaengine: edma: Get qDMA channel information from HW also
dmaengine: edma: Merge map_dmach_to_queue into assign_channel_eventq
dmaengine: edma: Correct PaRAM access function names (_parm_ to _param_)
...
In interleaved mode, when numf > 1, we have only one descriptor for the
transfer but this descriptor has to be added to the descs_list. If not,
when doing remove_xfer, the descriptor won't be put back in the
free_descs_list.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When putting back a descriptor to the free descs list, some fields are
not set to 0, it can cause bugs if someone uses it without having this
in mind.
Descriptor are not put back one by one so it is easier to clean
descriptors when we request them.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org #4.2
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The addressing mode we were using was not only incrementing the address at
each microblock, but also at each data boundary, which was severely slowing
the transfer, without any benefit since we were not using the data stride.
Switch to the micro block increment only in order to get back to an
acceptable performance level.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 6007ccb577 ("dmaengine: xdmac: Add interleaved transfer support")
Cc: stable@vger.kernel.org #4.2
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time we have aded a new capability for scatter-gathered memset using
dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Others
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2 which is
deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gQZ6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have aded a new capability for scatter-gathered memset
using dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Other:
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2
which is deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers"
[ The Kconfig and Makefile entries got re-sorted alphabetically, and I
handled the conflict with the new Intel integrated IDMA driver by
slightly mis-sorting it on purpose: "IDMA64" got sorted after "IMX" in
order to keep the Intel entries together. I think it might be a good
idea to just rename the IDMA64 config entry to INTEL_IDMA64 to make
the sorting be a true sort, not this mismash.
Also, this merge disables the COMPILE_TEST for the sun4i DMA
controller, because it does not compile cleanly at all. - Linus ]
* tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (89 commits)
dmaengine: ioatdma: add Broadwell EP ioatdma PCI dev IDs
dmaengine :ipu: change ipu_irq_handler() to remove compile warning
dmaengine: ioatdma: Fix variable array length
dmaengine: ioatdma: fix sparse "error" with prep lock
dmaengine: hdmac: Add memset capabilities
dmaengine: sort the sh Makefile
dmaengine: sort the sh Kconfig
dmaengine: sort the dw Kconfig
dmaengine: sort the Kconfig
dmaengine: sort the makefile
drivers/dma: make mv_xor.c driver explicitly non-modular
dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller
devicetree: Add bindings documentation for Analog Devices AXI-DMAC
dmaengine: xgene-dma: Fix the lock to allow client for further submission of requests
dmaengine: ioatdma: fix coccinelle warning
dmaengine: ioatdma: fix zero day warning on incompatible pointer type
dmaengine: tegra-apb: Simplify locking for device using global pause
dmaengine: tegra-apb: Remove unnecessary return statements and variables
dmaengine: tegra-apb: Avoid unnecessary channel base address calculation
dmaengine: tegra-apb: Remove unused variables
...
In cyclic mode, the round chaining has been broken by the introduction
of at_xdmac_queue_desc(): AT_XDMAC_MBR_UBC_NDE is set for all descriptors
excepted for the last one. at_xdmac_queue_desc() has to be called one
more time to chain the last and the first descriptors.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 0d0ee751f7 ("dmaengine: xdmac: Rework the chaining logic")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The XDMAC also supports memset operations over discontiguous areas. Add the
necessary logic to support this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the missing update of the transfer data width in
at_xdmac_prep_slave_sg().
Indeed, for each item in the scatter-gather list, we check whether the
transfer length is aligned with the data width provided by
dmaengine_slave_config(). If so, we directly use this data width for the
current part of the transfer we are preparing. Otherwise, the data width
is reduced to 8 bits (1 byte). Of course, the actual number of register
accesses must also be updated to match the new data width.
So one chunk was missing in the original patch (see Fixes tag below): the
number of register accesses was correctly set to (len >> fixed_dwidth) in
mbr_ubc but the real data width was not updated in mbr_cfg. Since mbr_cfg
may change for each part of the scatter-gather transfer this also explains
why the original patch used the Descriptor View 2 instead of the
Descriptor View 1.
Let's take the example of a DMA transfer to write 8bit data into an Atmel
USART with FIFOs. When FIFOs are enabled in the USART, its Transmit
Holding Register (THR) works in multidata mode, that is to say that up to
4 8bit data can be written into the THR in a single 32bit access and it is
still possible to write only one data with a 8bit access. To take
advantage of this new feature, the DMA driver was modified to allow
multiple dwidths when doing slave transfers.
For instance, when the total length is 22 bytes, the USART driver splits
the transfer into 2 parts:
First part: 20 bytes transferred through 5 32bit writes into THR
Second part: 2 bytes transferred though 2 8bit writes into THR
For the second part, the data width was first set to 4_BYTES by the USART
driver thanks to dmaengine_slave_config() then at_xdmac_prep_slave_sg()
reduces this data width to 1_BYTE because the 2 byte length is not aligned
with the original 4_BYTES data width. Since the data width is modified,
the actual number of writes into THR must be set accordingly.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 6d3a7d9e3a ("dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers")
Cc: stable@vger.kernel.org #4.0 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When using descriptor view 2 or higher, we don't write the configuration
into AT_XDMAC_CC register because this configuration will be fetch from
the descriptor. Unfortunately, the PROT bit is not updated with this
method, we have to do it manually before enabling the channel.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time we have support for few new devices, few new features and odd
fixes spread thru the subsystem.
New devices added
- support for CSRatlas7 dma controller
- Allwinner H3(sun8i) controller
- TI DMA crossbar driver on DRA7x
- new pxa driver
New features added:
- memset support is bought back now that we have a user in xdmac controller
- interleaved transfers support different source and destination strides
- supporting DMA routers and configuration thru DT
- support for reusing descriptors
- xdmac memset and interleaved transfer support
- hdmac support for interleaved transfers
- omap-dma support for memcpy
Others
- Constify platform_device_id
- mv_xor fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VM4w
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have support for few new devices, few new features and
odd fixes spread thru the subsystem.
New devices added:
- support for CSRatlas7 dma controller
- Allwinner H3(sun8i) controller
- TI DMA crossbar driver on DRA7x
- new pxa driver
New features added:
- memset support is bought back now that we have a user in xdmac controller
- interleaved transfers support different source and destination strides
- supporting DMA routers and configuration thru DT
- support for reusing descriptors
- xdmac memset and interleaved transfer support
- hdmac support for interleaved transfers
- omap-dma support for memcpy
Others:
- Constify platform_device_id
- mv_xor fixes and improvements"
* tag 'dmaengine-4.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: xgene: fix file permission
dmaengine: fsl-edma: clear pending interrupts on initialization
dmaengine: xdmac: Add memset support
Documentation: dmaengine: document DMA_CTRL_ACK
dmaengine: virt-dma: don't always free descriptor upon completion
dmaengine: Revert "drivers/dma: remove unused support for MEMSET operations"
dmaengine: hdmac: Implement interleaved transfers
dmaengine: Move icg helpers to global header
dmaengine: mv_xor: improve descriptors list handling and reduce locking
dmaengine: mv_xor: Enlarge descriptor pool size
dmaengine: mv_xor: add support for a38x command in descriptor mode
dmaengine: mv_xor: Rename function for consistent naming
dmaengine: mv_xor: bug fix for racing condition in descriptors cleanup
dmaengine: pl330: fix wording in mcbufsz message
dmaengine: sirf: add CSRatlas7 SoC support
dmaengine: xgene-dma: Fix "incorrect type in assignement" warnings
dmaengine: fix kernel-doc documentation
dmaengine: pxa_dma: add support for legacy transition
dmaengine: pxa_dma: add debug information
dmaengine: pxa: add pxa dmaengine driver
...
The XDMAC supports memset transfers, both over contiguous areas, and over
discontiguous areas through a LLI.
The current memset operation only supports contiguous memset for now, add some
support for it. Scatter-gathered memset will come eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that we can have ICGs set for both the source and destination (using
the icg field of struct data_chunk) or for only the source or the
destination (using the dst_icg or src_icg respectively), and that these
fields can be ignored depending on other parameters (src_inc, src_sgl,
etc.), the logic to get the actual ICG value can be quite tricky.
The XDMAC driver was already implementing it, but since we will need it in
other drivers, we can move it to the main header file.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rework slave configuration part in order to more report wrong errors
about the configuration.
Only maxburst and addr width values are checked when doing the slave
configuration. The validity of the channel configuration is done at
prepare time.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.0 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Using _bh variant for spin locks causes this kind of warning:
Starting logging: ------------[ cut here ]------------
WARNING: CPU: 0 PID: 3 at /ssd_drive/linux/kernel/softirq.c:151
__local_bh_enable_ip+0xe8/0xf4()
Modules linked in:
CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.1.0-rc2+ #94
Hardware name: Atmel SAMA5
[<c0013c04>] (unwind_backtrace) from [<c00118a4>] (show_stack+0x10/0x14)
[<c00118a4>] (show_stack) from [<c001bbcc>]
(warn_slowpath_common+0x80/0xac)
[<c001bbcc>] (warn_slowpath_common) from [<c001bc14>]
(warn_slowpath_null+0x1c/0x24)
[<c001bc14>] (warn_slowpath_null) from [<c001e28c>]
(__local_bh_enable_ip+0xe8/0xf4)
[<c001e28c>] (__local_bh_enable_ip) from [<c01fdbd0>]
(at_xdmac_device_terminate_all+0xf4/0x100)
[<c01fdbd0>] (at_xdmac_device_terminate_all) from [<c02221a4>]
(atmel_complete_tx_dma+0x34/0xf4)
[<c02221a4>] (atmel_complete_tx_dma) from [<c01fe4ac>]
(at_xdmac_tasklet+0x14c/0x1ac)
[<c01fe4ac>] (at_xdmac_tasklet) from [<c001de58>]
(tasklet_action+0x68/0xb4)
[<c001de58>] (tasklet_action) from [<c001dfdc>]
(__do_softirq+0xfc/0x238)
[<c001dfdc>] (__do_softirq) from [<c001e140>] (run_ksoftirqd+0x28/0x34)
[<c001e140>] (run_ksoftirqd) from [<c0033a3c>]
(smpboot_thread_fn+0x138/0x18c)
[<c0033a3c>] (smpboot_thread_fn) from [<c0030e7c>] (kthread+0xdc/0xf0)
[<c0030e7c>] (kthread) from [<c000f480>] (ret_from_fork+0x14/0x34)
---[ end trace b57b14a99c1d8812 ]---
It comes from the fact that devices can called some code from the DMA
controller with irq disabled. _bh variant is not intended to be used in
this case since it can enable irqs. Switch to irqsave/irqrestore variant to
avoid this situation.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.0 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
