There is a possibility of a deadlock due to the way locks are
acquired and released in qib_set_uevent_bits(). The function
qib_set_uevent_bits() is called in process context and it uses
spin_lock() and spin_unlock(). This same lock is acquired/released
in interrupt context which can lead to a deadlock when running on
the same cpu.
The fix is to replace spin_lock() and spin_unlock() with
spin_lock_irqsave() and spin_unlock_irqrestore() respectively in
qib_set_uevent_bits().
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Indicate the number of free user contexts via the sysfs file
/sys/class/infiniband/qib0/nfreectxts as required for PSM.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Adapt to use new APIs. We plan to remove old one later and plan to
change current->cpus_allowed implementation.
No functional change.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Due to timing, it is possible for the LOS and DFE to remain on. This
is due to the link progressing to LinkUP prior to the driver getting
the first Status Changed interrupt. By expanding the conditions under
which LOS is turned off and DFE timeout is being set, timing is no
longer an issue.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add basic RDMA netlink infrastructure that allows for registration of
RDMA clients for which data is to be exported and supplies message
construction callbacks.
Signed-off-by: Nir Muchtar <nirm@voltaire.com>
[ Reorganize a few things, add CONFIG_NET dependency. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver reads PCI revision ID from the PCI configuration register
while it's already stored by PCI subsystem in the revision field of
struct pci_dev.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The time limit test now correctly checks against current jiffies to
avoid the hang.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In most cases, get_user_pages and get_user_pages_fast should be used
to pin user pages in memory. But sometimes, some special flags except
FOLL_GET, FOLL_WRITE and FOLL_FORCE are needed, for example in
following patch, KVM needs FOLL_HWPOISON. To support these users,
__get_user_pages is exported directly.
There are some symbol name conflicts in infiniband driver, fixed them too.
Signed-off-by: Huang Ying <ying.huang@intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Michel Lespinasse <walken@google.com>
CC: Roland Dreier <roland@kernel.org>
CC: Ralph Campbell <infinipath@qlogic.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Set the M_Key field in SubnGet and SugnGetResp MADs based on correctly
interpreting the protection level specified in the M_KeyProtBits field.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For active and far-EQ cables use an LE2 value of 0 for improved SI.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix a bug which causes the driver to return incorrect MADs as a
response to Set(PortInfo) which sets the link width to 0xFF or link
speed to 0xF.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a double completion associated with error handling for RC QPs.
The sequence is:
- The do_rc_ack() routine fields an RNR nack and there are 0
rnr_retries configured on the QP.
- qib_error_qp() stops the pending timer
- qib_rc_send_complete() is called from sdma_complete()
- qib_rc_send_complete() starts the timer because the msb of the psn
just completed says an ack is needed.
- a bunch of flushes occur as ipoib posts WQEs to an error'ed QP
- rc_timeout() calls qib_restart_rc()
- qib_restart_rc() calls qib_send_complete() with a
IB_WC_RETRY_EXC_ERR on a wqe that has already been completed in the
past
The fix avoids starting the timer since another packet will never
arrive.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The following panic BUG_ON occurs during qib testing:
Kernel BUG at include/linux/timer.h:82
RIP [<ffffffff881f7109>] :ib_qib:start_timer+0x73/0x89
RSP <ffffffff80425bd0>
<0>Kernel panic - not syncing: Fatal exception
<0>Dumping qib trace buffer from panic
qib_set_lid INFO: IB0:1 got a lid: 0xf8
Done dumping qib trace buffer
BUG: warning at kernel/panic.c:137/panic() (Tainted: G
The flaw is due to a missing state test when processing responses that
results in an add_timer() call when the same timer is already queued.
This code was executing in parallel with a QP destroy on another CPU
that had changed the state to reset, but the missing test caused to
response handling code to run on into the panic.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Hold the IB link at DISABLED until we get the correct TX settings
on mezz boards.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA: Update workqueue usage
RDMA/nes: Fix incorrect SFP+ link status detection on driver init
RDMA/nes: Fix SFP+ link down detection issue with switch port disable
RDMA/nes: Generate IB_EVENT_PORT_ERR/PORT_ACTIVE events
RDMA/nes: Fix bonding on iw_nes
IB/srp: Test only once whether iu allocation succeeded
IB/mlx4: Handle protocol field in multicast table
RDMA: Use vzalloc() to replace vmalloc()+memset(0)
mlx4_{core, ib, en}: Fix driver when sizeof (phys_addr_t) > sizeof (long)
IB/mthca: Fix driver when sizeof (phys_addr_t) > sizeof (long)
* ib_wq is added, which is used as the common workqueue for infiniband
instead of the system workqueue. All system workqueue usages
including flush_scheduled_work() callers are converted to use and
flush ib_wq.
* cancel_delayed_work() + flush_scheduled_work() converted to
cancel_delayed_work_sync().
* qib_wq is removed and ib_wq is used instead.
This is to prepare for deprecation of flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (42 commits)
IB/qib: Fix refcount leak in lkey/rkey validation
IB/qib: Improve SERDES tunning on QMH boards
IB/qib: Unnecessary delayed completions on RC connection
IB/qib: Issue pre-emptive NAKs on eager buffer overflow
IB/qib: RDMA lkey/rkey validation is inefficient for large MRs
IB/qib: Change QPN increment
IB/qib: Add fix missing from earlier patch
IB/qib: Change receive queue/QPN selection
IB/qib: Fix interrupt mitigation
IB/qib: Avoid duplicate writes to the rcv head register
IB/qib: Add a few new SERDES tunings
IB/qib: Reset packet list after freeing
IB/qib: New SERDES init routine and improvements to SI quality
IB/qib: Clear WAIT_SEND flags when setting QP to error state
IB/qib: Fix context allocation with multiple HCAs
IB/qib: Fix multi-Florida HCA host panic on reboot
IB/qib: Handle transitions from ACTIVE_DEFERRED to ACTIVE better
IB/qib: UD send with immediate receive completion has wrong size
IB/qib: Set port physical state even if other fields are invalid
IB/qib: Generate completion callback on errors
...
The mr optimization introduced a reference count leak on an exception
test. The lock/refcount manipulation is moved down and the problematic
exception test now calls bail to insure that the lock is released.
Additional fixes as suggested by Ralph Campbell <ralph.campbell@qlogic.org>:
- reduce lock scope of dma regions
- use explicit values on returns vs. automatic ret value
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Improve the QMH SERDES tunning on initial driver load by having the
driver go through a link state change.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently on receipt of a response message (ACKs, RDMA Response,
Atomic Responses etc.) if the SDMA completion counter is not advanced
the driver delays the completion of the WQE. In most cases this is
overly pessimistic as the response (ACK) to a previously transmitted
send implies that the send is complete. Ensure that SDMA queue is
progressed appropriately before determining if a send has delayed
completions.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Under congestion resulting in eager buffer overflow attempt to send
pre-emptive NAKs if header queue entries with TID errors are generated
and a valid header is present. This prevents long timeouts and flow
restarts if a trailing set of packets are dropped due to eager
overflows. Pre-emptive NAKs are currently only supported for RDMA
writes.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current code loops during rkey/lkey validiation to isolate the MR
for the RDMA, which is expensive when the current operation is inside
a very large memory region.
This fix optimizes rkey/lkey validation routines for user memory
regions and fast memory regions. The MR entry can be isolated by
shifts/mods instead of looping. The existing loop is preserved for
phys memory regions for now.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Changing from +1 to +2 allows for better QP distribution across
receive contexts.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The upstream code was missing part of a receive/error race fix from
the internal tree. Add the missing part, which makes future merges
possible.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The basic idea is that on SusieQ, the difficult part of mapping QPN to
context is handled by the mapping registers so the generic QPN
allocation doesn't need to worry about chip specifics. For Monty and
Linda, there is no mapping table so the qpt->mask (same as
dd->qpn_mask), is used to see if the QPN to context falls within
[zero..dd->n_krcv_queues).
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For SusieQ we need to write to the interrupt timer register before
updating the header queue head with interrupt count. This is to
ensure that the timer is enabled properly and a receive available
interrupt is delivered. Otherwise this interrupt can be lost if the
receiver header/eager queues are full before the timer is enabled.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Avoid duplicate writes to the head register as this can lead to lost
interrupts if the context goes full before the second write is done.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add new SERDES tuning to aid manufacturing.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reset the list pointers after freeing the SDMA packet list. This is
done to any potential double-free cases.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement new SERDES initialization routine and improvements to signal
integrity -- disable LE1 adaptation, disable LOS after link-up, set
better SERDES parameters.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If these flags are set when the QP is transitioned to the error state,
it will wait until the flags are cleared, which may never happen if
the error transition is due to a link going down.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver was incorrectly choosing HCAs on which to allocate new user
contexts based on overall count of usable ports regardless whether the
usable port was on the currently selected HCA.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add check when setting configured contexts that the value does not
exceed the number of contexts allocated for the card. If the value
exceeds the already allocated count, set it to what is already
allocated.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the link transitions from ACTIVE_DEFERRED to ACTIVE, the driver
only sees the ACTIVE state. With this change, it will check whether
the state was already ACTIVE and if so, it will not generated IB
events and will not clear symbol error counts.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to generate receive completion entries for UD send with
immediate contains the wrong payload length. This is because when the
code to compute the payload size was moved, the value of hdrsize
didn't get moved too. The fix is to update tlen directly.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IBTA vol. 1 release 1.2.1 spec. says:
C14-24.2.1: If PortInfo:Portstate=Down, then a SubnSet(PortInfo) shall
make any changes it specifies to PortInfo:PortPhysicalState; any other
result is vendor-dependent.
The patch changes the error handling so that the reply says there are
invalid fields but still attempts to set fields that are in range
including PortInfo:PortPhysicalState.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to IBTA vol. 1, C11-30.1.1, a notification callback is
invoked if the CQ is armed for the next solicited completion event or
an error completion. The error case wasn't being generated correctly.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support to recognize another board variation named QME7362.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The receive header queue sizes need to modified for performance
tuning. Three module parameters are added to support this.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dget_locked was a shortcut to avoid the lazy lru manipulation when we already
held dcache_lock (lru manipulation was relatively cheap at that point).
However, how that the lru lock is an innermost one, we never hold it at any
caller, so the lock cost can now be avoided. We already have well working lazy
dcache LRU, so it should be fine to defer LRU manipulations to scan time.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Make d_count non-atomic and protect it with d_lock. This allows us to ensure a
0 refcount dentry remains 0 without dcache_lock. It is also fairly natural when
we start protecting many other dentry members with d_lock.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
split invalidate_inodes()
fs: skip I_FREEING inodes in writeback_sb_inodes
fs: fold invalidate_list into invalidate_inodes
fs: do not drop inode_lock in dispose_list
fs: inode split IO and LRU lists
fs: switch bdev inode bdi's correctly
fs: fix buffer invalidation in invalidate_list
fsnotify: use dget_parent
smbfs: use dget_parent
exportfs: use dget_parent
fs: use RCU read side protection in d_validate
fs: clean up dentry lru modification
fs: split __shrink_dcache_sb
fs: improve DCACHE_REFERENCED usage
fs: use percpu counter for nr_dentry and nr_dentry_unused
fs: simplify __d_free
fs: take dcache_lock inside __d_path
fs: do not assign default i_ino in new_inode
fs: introduce a per-cpu last_ino allocator
new helper: ihold()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (63 commits)
IB/qib: clean up properly if pci_set_consistent_dma_mask() fails
IB/qib: Allow driver to load if PCIe AER fails
IB/qib: Fix uninitialized pointer if CONFIG_PCI_MSI not set
IB/qib: Fix extra log level in qib_early_err()
RDMA/cxgb4: Remove unnecessary KERN_<level> use
RDMA/cxgb3: Remove unnecessary KERN_<level> use
IB/core: Add link layer type information to sysfs
IB/mlx4: Add VLAN support for IBoE
IB/core: Add VLAN support for IBoE
IB/mlx4: Add support for IBoE
mlx4_en: Change multicast promiscuous mode to support IBoE
mlx4_core: Update data structures and constants for IBoE
mlx4_core: Allow protocol drivers to find corresponding interfaces
IB/uverbs: Return link layer type to userspace for query port operation
IB/srp: Sync buffer before posting send
IB/srp: Use list_first_entry()
IB/srp: Reduce number of BUSY conditions
IB/srp: Eliminate two forward declarations
IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
IB: Replace EXTRA_CFLAGS with ccflags-y
...
Clean up properly if pci_set_consistent_dma_mask() fails.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some PCIe root complex chip sets don't support advanced error reporting.
Allow the driver to load OK if pci_enable_pcie_error_reporting() fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If CONFIG_PCI_MSI is not set, and a QLE7140 is present, the pointer
"dd" is uninitialized.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Noticed this odd looking thing in dmesg:
ib_qib 0000:02:00.0: <3>ib_qib: Unable to enable pcie error reporting: -5
which is due to a bad use of dev_info.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Instead of always assigning an increasing inode number in new_inode
move the call to assign it into those callers that actually need it.
For now callers that need it is estimated conservatively, that is
the call is added to all filesystems that do not assign an i_ino
by themselves. For a few more filesystems we can avoid assigning
any inode number given that they aren't user visible, and for others
it could be done lazily when an inode number is actually needed,
but that's left for later patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
See table 35 in IBA - the header order for RDMA_WRITE_ONLY_WITH_IMMEDIATE
and SEND_LAST_WITH_IMMEDIATE is different: the RDMA_WRITE_ONLY has
a RETH header before the immediate data, so we need a different code path
to extract the immediate data.
I tested this with a userspace app that does RDMA_WRITE with immediate
on a QLE7140.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Fix build failure on sparc64 which is missing the include of
<linux/slab.h> via <asm/pci.h> that x86, powerpc, ia64, etc. have.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When transitioning a QP to the error state, in progress RWQEs need to
be marked complete. This also involves releasing the reference count
to the memory regions referenced in the SGEs. The locking in the
receive packet processing wasn't sufficient to prevent qib_error_qp()
from modifying the r_sge state at the same time, thus leading to
kernel panics.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't processes too many packets without allowing other IRQ functions
a chance to run. Otherwise, there is a chance of getting a "soft
lockup" messages and poor application response times.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Up to now, we have set the number of available user contexts based on
the number of hardware contexts which is set according to the number
of available CPUs. This was fine since most CPUs had a power of two
number of cores and the chip supported 4, 8, or 16 user contexts. Now
that some systems have 12 cores, the default isn't optimal and should
be set to 12 even though 16 hardware contexts need to be enabled.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We used to allow only full specification, or using all contexts within
an HCA before moving to the next HCA. We now allow an additional
method -- round-robining through HCAs -- and make that the default.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Turn off IB latency mode. This improves link quality for slower
process chips.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the default llseek action gets changed to no_llseek, all file
systems relying on the current behaviour need to set explicit .llseek
operations.
In case of qib_fs, we want the files to be seekable, so
generic_file_llseek fits best.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than use a variable size array allocation on the stack,
define a constant for the maximum array size possible.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Extract the microcode for the QLogic QLE7220 series IB HCA and use the
kernel microcode request facility to load the microcode. This
supports Debian Linux's requirements to separate microcode which
doesn't have open source code available from the device driver.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix world-writable child interface control sysfs attributes
IB/qib: Clean up properly if qib_init() fails
IB/qib: Completion queue callback needs to be single threaded
IB/qib: Update 7322 serdes tables
IB/qib: Clear 6120 hardware error register
IB/qib: Clear eager buffer memory for each new process
IB/qib: Mask hardware error during link reset
IB/qib: Don't mark VL15 bufs as WC to avoid a rare 7322 chip problem
RDMA/cxgb4: Derive smac_idx from port viid
RDMA/cxgb4: Avoid false GTS CIDX_INC overflows
RDMA/cxgb4: Don't call abort_connection() for active connect failures
RDMA/cxgb4: Use the DMA state API instead of the pci equivalents
If qib_init() fails, the driver fails to free memory, unregister
device files, and unregister with the PCIe framework. The driver will
unload without error but a subsequent driver load will cause the
system to panic. This was found by changing the 7220 code to load the
serdes microcode separately and not installing the microcode file.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Workqueues aren't exactly equivalent to tasklets since the callback
function may be called from multiple CPUs before the callback returns.
This causes completion notification callbacks to have MT bugs since
they weren't expecting this behavior. The fix is to use a single
threaded work queue.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hardware error register needs to be cleared or another interrupt
will be generated, thus causing an infinite loop. This is a
regression introduced when removing debug output.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The eager buffers are not being cleared before being mmapped into a
new user address space. This is a potential security risk and should
be fixed. Note that the eager header queue is already being cleared.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The HCA checks for certain hardware errors which can be falsely
triggered when the IB link is reset. The fix is to mask them rather
than report them.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't set write combining via PAT on the VL15 buffers to avoid a rare
problem with unaligned writes from interrupt-flushed store buffers.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
get_sb_single() calls fill_super with superblock locked; calling
deactivate_super() will deadlock immedately. Moreover, if fill_super
callback returns an error, get_sb_single() will release the reference
to superblock itself just fine.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The DCA code was left over from internal development to test the
hardware feature and allow performance testing. The results were
mixed and will require some additional work to make full use of the
feature. Therefore, it is being removed for now.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As part of the earlier patches submitted and reviewed, it was agreed
to change the way serdes tuning parameters were specified to the
driver. The updated patch got dropped by the linux-rdma email list so
the earlier version of qib_iba7322.c ended up being used. This patch
updates qib_iab7322.c to the simpler, single parameter method of
setting the serdes parameters.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some of the qib sysfs code passes a buffer pointer into
simple_read_from_buffer() but relies on a function call in another
parameter of the same call to initialize that pointer. Since the order
of evaluation of function parameters is undefined, this will break if
gcc chooses the wrong order.
Fix this by splitting the code into two separate function calls.
This was noticed because of warnings like the following on ppc:
drivers/infiniband/hw/qib/qib_fs.c: In function 'portcntrs_2_read':
drivers/infiniband/hw/qib/qib_fs.c:203: warning: 'counters' is used uninitialized in this function
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a compile error saying qib_init_iba6120_funcs() is
undefined when CONFIG_PCI_MSI is not defined. Thanks to Randy Dunlap
<randy.dunlap@oracle.com> for finding this and suggesting the fix.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a low-level IB driver for QLogic PCIe adapters.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
