The driver implements ndo_switch_fib_ipv4_add/del ops to add/del/mod IPv4
routes to/from switchdev device. Once a route is added to the device, and the
route's nexthops are resolved to neighbor MAC address, the device will forward
matching pkts rather than the kernel. This offloads the L3 forwarding path
from the kernel to the device. Note that control and management planes are
still mananged by Linux; only the data plane is offloaded. Standard routing
control protocols such as OSPF and BGP run on Linux and manage the kernel's FIB
via standard rtm netlink msgs...nothing changes here.
A new hash table is added to rocker to track neighbors. The driver listens for
neighbor updates events using netevent notifier NETEVENT_NEIGH_UPDATE. Any ARP
table updates for ports on this device are recorded in this table. Routes
installed to the device with nexthops that reference neighbors in this table
are "qualified". In the case of a route with nexthops not resolved in the
table, the kernel is asked to resolve the nexthop.
The driver uses fib_info->fib_priority for the priority field in rocker's
unicast routing table.
The device can only forward to pkts matching route dst to resolved nexthops.
Currently, the device only supports single-path routes (i.e. routes with one
nexthop). Equal Cost Multipath (ECMP) route support will be added in followup
patches.
This patch is driver support for unicast IPv4 routing only. Followup patches
will add driver and infrastructure for IPv6 routing and multicast routing.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is removed (e.g. using unbind through sysfs), the
clocks get disabled twice, once on fec_enet_close and once on
fec_drv_remove. Since the clocks are enabled only once, this leads
to a warning:
WARNING: CPU: 0 PID: 402 at drivers/clk/clk.c:992 clk_core_disable+0x64/0x68()
Remove the call to fec_enet_clk_enable in fec_drv_remove to balance
the clock enable/disable calls again. This has been introduce by
e8fcfcd568 ("net: fec: optimize the clock management to save power").
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest spec "I-IPA01-0266-USR Rev 10" limit the MID field length to 12 bit
value. For previous versions it is 16 bit value.
This change will not break the backward compatibility as the latest ID value is
7 and with in the 12 bit value limit.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eTSEC of-nodes may have children which are not queue-group nodes. For
example new-style fixed-phy declarations. These where incorrectly
assumed to be additional queue-groups.
Change the search to filter out any nodes which are not queue-groups,
or have been disabled.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Ben Hutchings, ioremap uses unsigned long as
its parameter type, so we should be using that instead of u32
or int.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_set_wol() correctly sets MPD_PW_EN when a password is specified
to match magic packets against, however, when we switch from a
password-matching to a matching without password we would leave this bit
turned on, and GENET would only match magic packets with passwords.
This can be reproduced using the following sequence:
ethtool -s eth0 wol g
ethtool -s eth0 wol s sopass 00:11:22:33:44:55
ethtool -s eth0 wol g
The simple fix is to clear the MPD_PWD_EN bit when WAKE_MAGICSECURE is
not set.
Fixes: c51de7f397 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to i40e only.
Greg provides fixes for the NPAR transmit scheduler where the driver
initialization caused the BW configurations to not take effect, so use
a BW configuration read and write back to "kick" the transmit scheduler
into action. Fixes the ethtool offline test, where we were not actually
taking the device offline before doing the testing.
Matt modifies the get and set LED functions so they ignore activity LEDs
since we are required to blink the link LEDs only.
Neerav provides a workaround for whenever a DCBX configuration is changed,
where the firmware doe not set the operational status bit of the
application TLV status as returned from the "Get CEE DCBX Oper Cfg" admin
queue command. So remove the check for the operational and sync bits of
the application TLV status until a firmware fix is provided.
Shannon changes the driver to grab the NVM devstarter version and not
the image version, since it is the more useful version and is what
should be displayed. Moves the IRQ tracking setup and tear down into
the same routines that do the IRQ setup and tear down. This keeps
like activities together and allows us to track exactly the number
of vectors reserved from the OS, which may be fewer than are available
from the hardware.
Jesse provides a fix to use a more portable sign extension by replacing
0xffff.... with ~(u64)0 or ~(u32)0. Also fixes XPS mask when resetting,
where the driver would accidentally clear the XPS mask for all queues
back to 0. This caused higher CPU utilization and had some other
performance impacts for transmit tests. Cleans up some whitespace
formatting.
Catherine provides a fix where some firmware versions are incorrectly
reporting a breakout cable as PHY type 0x3 when it should be 0x16
(I40E_PHY_TYPE_10GBASE_SFPP_CU). Adds the 10G and 40G AOC PHY types
to the case statement in get_media_type and ethtool get_settings so
that the correct information gets reported back to the user.
Anjali provides IOREMAP changes for future device support, where we
do not want to map the whole CSR space since some of it is mapped by
other drivers with different mapping methods.
Mitch changes the i40e driver to not "spam" the system log with
messages about VF VSI when VFs are created and when they are reset to
reduce user annoyance.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de7b5b3d79 ("net: eth: xgene: change APM X-Gene SoC platform
ethernet to support ACPI") breaks booting with devicetree with UEFI
firmware. In that case, I get:
Unhandled fault: synchronous external abort (0x96000010) at 0xfffffc0000620010
Internal error: : 96000010 [#1] SMP
Modules linked in: vfat fat xfs libcrc32c ahci_xgene libahci_platform libahci
CPU: 7 PID: 634 Comm: NetworkManager Not tainted 4.0.0-rc1+ #4
Hardware name: AppliedMicro Mustang/Mustang, BIOS 1.1.0-rh-0.14 Mar 1 2015
task: fffffe03d4c7e100 ti: fffffe03d4e24000 task.ti: fffffe03d4e24000
PC is at xgene_enet_rd_mcx_mac.isra.11+0x58/0xd4
LR is at xgene_gmac_tx_enable+0x2c/0x50
pc : [<fffffe000069d6fc>] lr : [<fffffe000069dcc4>] pstate: 80000145
sp : fffffe03d4e27590
x29: fffffe03d4e27590 x28: 0000000000000000
x27: fffffe03d4e277c0 x26: fffffe03da8fda10
x25: fffffe03d4e2760c x24: fffffe03d49e28c0
x23: fffffc0000620004 x22: 0000000000000000
x21: fffffc0000620000 x20: fffffc0000620010
x19: 000000000000000b x18: 000003ffd4a96020
x17: 000003ff7fc1f7a0 x16: fffffe000079b9cc
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: fffffe03d4e24000
x11: fffffe03d4e27da0 x10: 0000000000000001
x9 : 0000000000000000 x8 : fffffe03d4e27a20
x7 : 0000000000000000 x6 : 00000000ffffffef
x5 : fffffe000105f7d0 x4 : fffffe00007ca8c8
x3 : fffffe03d4e2760c x2 : 0000000000000000
x1 : fffffc0000620000 x0 : 0000000040000000
Process NetworkManager (pid: 634, stack limit = 0xfffffe03d4e24028)
Stack: (0xfffffe03d4e27590 to 0xfffffe03d4e28000)
...
Call trace:
[<fffffe000069d6fc>] xgene_enet_rd_mcx_mac.isra.11+0x58/0xd4
[<fffffe000069dcc0>] xgene_gmac_tx_enable+0x28/0x50
[<fffffe00006a112c>] xgene_enet_open+0x2c/0x130
[<fffffe00007b9254>] __dev_open+0xc8/0x148
[<fffffe00007b956c>] __dev_change_flags+0x90/0x158
[<fffffe00007b9664>] dev_change_flags+0x30/0x70
[<fffffe00007c8ab8>] do_setlink+0x278/0x870
[<fffffe00007c95bc>] rtnl_newlink+0x404/0x6a8
[<fffffe00007c8040>] rtnetlink_rcv_msg+0x98/0x218
[<fffffe00007e78e4>] netlink_rcv_skb+0xe0/0xf8
[<fffffe00007c7f94>] rtnetlink_rcv+0x30/0x44
[<fffffe00007e6f2c>] netlink_unicast+0xfc/0x210
[<fffffe00007e75b8>] netlink_sendmsg+0x498/0x5ac
[<fffffe00007990b8>] do_sock_sendmsg+0xa4/0xcc
[<fffffe000079a958>] ___sys_sendmsg+0x1fc/0x208
[<fffffe000079b984>] __sys_sendmsg+0x4c/0x94
[<fffffe000079b9f8>] SyS_sendmsg+0x2c/0x3c
The problem here is that the enet hw clocks are not getting
initialized because of a test to avoid the initialization if
UEFI is used to boot. This is an incorrect test. When booting
with UEFI and devicetree, the kernel must still initialize
the enet hw clocks. If booting with ACPI, the clock hw is
not exposed to the kernel and it is that case where we want
to avoid initializing clocks.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Feng Kan <fkan@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Cc: stable<stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow for better scalability on systems with large core counts, we
will try and allocate enough RDMA Concentrator IQs and MSI/X vectors as
we have cores. If we cannot get enough MSI/X vectors, fall back to the
minimum required: 1 per adapter rx channel.
Also clean up cxgb_enable_msix() to make it readable and correct a bug
where the vectors are not correctly assigned if the driver doesn't get
the full amount requested.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a common function for all Rx queue allocation.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling a from-guest frag list, xenvif_handle_frag_list()
replaces the frags before calling the destructor to clean up the
original (foreign) frags. Whilst this is safe (the destructor doesn't
actually use the frags), it looks odd.
Reorder the function to be less confusing.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time a VIF is destroyed up to 256 pages may be leaked if packets
with more than MAX_SKB_FRAGS frags were transmitted from the guest.
Even worse, if another user of ballooned pages allocated one of these
ballooned pages it would not handle the unexpectedly >1 page count
(e.g., gntdev would deadlock when unmapping a grant because the page
count would never reach 1).
When handling a from-guest skb with a frag list, unref the frags
before releasing them so they are freed correctly when the VIF is
destroyed.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct pointer arithmetic to get the pointer to each stat.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 1.2.11 and i40evf to 1.2.5
Change-ID: Ie13375941606b0a027e5b5dbc235f5f5f03b75c8
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF driver spams the system log with messages about VF VSI when VFs
are created, as well as each time they are reset. This is annoying, and
the information isn't even useful most of the time.
Remove this message to reduce user annoyance.
Change-ID: I8de90d05380f54b038c9c8c3265150be87c9242c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the IRQ tracking setup and teardown into the same routines that
do the IRQ setup and teardown. This keeps like activities together and
allows us to track exactly the number of vectors reserved from the OS,
which may be fewer than are available from the HW.
Change-ID: I6b2b1a955c5f0ac6b94c3084304ed0b2ea6777cf
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For future device support we do not want to map the whole CSR space since some
of it is mapped by other drivers with different mapping methods.
Note: As a side effect, the flash region (if exposed through the memory map)
gets unmapped too since it follows the future use region.
Change-ID: Ic729a2eacd692984220b1a415ff4fa0f98ea419a
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix some double blank lines and un-split a function declaration that all
fits on one line. Also make i40e_get_priv_flags static.
Change-ID: I11b5d25d1153a06b286d0d2f5d916d7727c58e4a
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the 10G and 40G AOC PHY types to the case statement in get_media_type
and ethtool get_settings so that the correct information gets reported
back to the user.
Change-ID: I1b4849d22199a9acf7c8807166d0317c1faad375
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the system administrator is requesting an offline diagnostic test using
'ethtool -t' then we should, you know, actually take the device offline
before doing the testing.
Change-ID: I6afa1cbfcc821c9ab6e6f47ed4d8dc2d8dd20e82
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some FW versions are incorrectly reporting a breakout cable as PHY type
0x3 when it should be 0x16 (I40E_PHY_TYPE_10GBASE_SFPP_CU).
If we get this value back from FW and the version is < 4.40, reassign it
to I40E_PHY_TYPE_10GBASE_SFPP_CU.
Change-ID: Ibb41a0e3cd2c0753744e8553959240df6ed13ae8
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During resets (possibly caused by a Tx hang) the driver would
accidentally clear the XPS mask for all queues back to 0.
This caused higher CPU utilization and had some other performance impacts
for transmit tests.
Change-ID: I95f112432c9e643a153eaa31cd28cdcbfdd01831
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit below introduced an unsafe dereference of
mvmvif->phy_ctxt. It can be NULL even if we hold the mutex.
We can be handling a BT Coex notification while the vif has
already been unassigned. This can happen since the BT Coex
notification is hanled asynchronuously: we can have started
to handle the BT Coex notification trying to acquire the
mutex while the unassign flow already got it. The BT Coex
notification handling will wait for the mutext. I'll get it
later, but then mvmvif->phy_ctxt will be NULL.
Panic log:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<f985180d>] iwl_mvm_bt_notif_iterator+0x9d/0x340 [iwlmvm]
*pdpt = 0000000000000000 *pde = f000eef300000007
Oops: 0000 [#1] SMP
Workqueue: events iwl_mvm_async_handlers_wk [iwlmvm]
task: ed719b20 ti: ec03e000 task.ti: ec03e000
EIP: 0060:[<f985180d>] EFLAGS: 00010202 CPU: 2
EIP is at iwl_mvm_bt_notif_iterator+0x9d/0x340 [iwlmvm]
EAX: 00000000 EBX: f6d3cb70 ECX: f6d3cb70 EDX: 00000000
ESI: ec03fe40 EDI: efeb8810 EBP: ec03fdf0 ESP: ec03fdac
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000000 CR3: 01a1a000 CR4: 001407f0
Stack:
f743ca80 f744a404 ec03fdcc c10e3952 00003aba f743ca80 00000246 f743ca80
00000246 00000000 00000001 00000000 ebd45ff6 ebd458a4 f6d3c500 ebd45578
ebd44b01 ec03fe18 f99e1bc2 00000002 ebd44bc0 f9851770 00000000 f6d3c500
Call Trace:
[<c10e3952>] ? ring_buffer_unlock_commit+0xa2/0xd0
[<f99e1bc2>] __iterate_interfaces+0x82/0x110 [mac80211]
[<f9851770>] ? iwl_mvm_bt_coex_reduced_txp+0x140/0x140 [iwlmvm]
[<f99e1c6a>] ieee80211_iterate_active_interfaces_atomic+0x1a/0x20 [mac80211]
[<f9851427>] iwl_mvm_bt_coex_notif_handle+0x77/0x280 [iwlmvm]
[<f9852161>] iwl_mvm_rx_bt_coex_notif_old+0x211/0x220 [iwlmvm]
[<f9850b8b>] iwl_mvm_rx_bt_coex_notif+0x19b/0x1b0 [iwlmvm]
[<f983944f>] iwl_mvm_async_handlers_wk+0x7f/0xe0 [iwlmvm]
CC: <stable@vger.kernel.org> [3.19+]
Fixes: 123f515635 ("iwlwifi: mvm: BT Coex - add support for TTC / RRC")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use automatic sign extension by replacing 0xffff... constants
with ~(u64)0 or ~(u32)0.
Change-ID: I73cab4cd2611795bb12e00f0f24fafaaee07457c
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
0x2A is the NVM version so it has useful data but it is per image
version every image can have a different one. 0x18 is the dev starter
version which all the images for release will have the same version.
Of the two 0x18 is more useful and is what should be displayed.
Change-ID: Idf493da13a42ab211e2de0bef287f5de51033cca
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In CEE mode the firmware does not set the operational status bit of
the application TLV status as returned from the "Get CEE DCBX Oper Cfg"
AQ command. This occurs whenever a DCBX configuration is changed.
This is a workaround to remove the check for the operational and sync bits
of the application TLV status till a firmware fix is provided.
Change-ID: I1a31ff2fcadcb06feb5b55776a33593afc6ea176
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify our get and set LED functions so they ignore activity LEDs,
as we are required to blink the link LEDs only.
Change-ID: I647ea67a6fc95cbbab6e3cd01d81ec9ae096a9ad
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent changes to the driver initialization have caused the BW
configurations to not take effect. We use a BW configuration read and
write back to "kick" the Tx scheduler into action.
Change-ID: I94ab377c58d3a3986e3de62b6c199be3fd2ee5e6
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Use c_index and ring->c_index to determine how many TxCBs/TxBDs are
ready for cleanup
- c_index = the current value of TDMA_CONS_INDEX
- TDMA_CONS_INDEX is HW-incremented and auto-wraparound (0x0-0xFFFF)
- ring->c_index = __bcmgenet_tx_reclaim() cleaned up to this point on
the previous invocation
2. Add bcmgenet_tx_ring->clean_ptr
- index of the next TxCB to be cleaned
- incremented as TxCBs/TxBDs are processed
- value always in range [ring->cb_ptr, ring->end_ptr]
3. Fix incrementing of dev->stats.tx_packets
- should be incremented only when tx_cb_ptr->skb != NULL
These changes simplify __bcmgenet_tx_reclaim(). Furthermore, Tx ring size
can now be any value.
With the old code, Tx ring size had to be a power-of-2:
num_tx_bds = ring->size;
c_index &= (num_tx_bds - 1);
last_c_index &= (num_tx_bds - 1);
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I recently did a rework of the smc91x driver and did some build-testing
by compiling hundreds of randconfig kernels. Unfortunately, my script
was wrong and did not actually test the configurations that mattered,
so I introduced stupid typos in almost every file I touched.
I fixed my script now, built all configurations that actually matter
and fixed all the typos, this is the result.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b70661c708 ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pJAi
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.1-20150304' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-03-04
this is a pull request of 3 patches for net-next/master.
Aaron Wu contributes three patches for the blackfin can driver, which
cleans up the driver and makes use of more platform independent code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.
Fixes: 3d249d4ca7 "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the .sriov_configure() PCI method to allow for
runtime enabling/disabling of VFs. The module param "num_vfs" is now
deprecated.
At the time of driver load the PF-pool resources are allocated to the PF.
When the user enables VFs, the resources are then re-distributed across
PFs and VFs based on the number of VFs enabled.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SR-IOV is enabled in the adapter, the FW distributes resources
evenly across the PF and it's VFs. This is currently done only for some
resources.
This patch adds support for a new cmd that queries the FW for the list
of resources for which the distribution is allowed and distributes them
accordingly.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BE2, BE3 and Skhawk-R chips one non-RSS (called "default") RXQ was
needed to receive non-IP traffic. Some FW versions now export a
capability called IFACE_FLAGS_DEFQ_RSS where this requirement doesn't hold.
On such FWs the driver now does not create the non-RSS default queue.
This prevents wasting one RXQ per VF.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the backward compatibile of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove Kconfig dependency and enable driver for
all ARCHs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case there was some tx buffer reclaimed and not enough rx packets
to consume the whole budget, napi_complete would not be called and
interrupts would be kept disabled, effectively resulting in the
network core never to call the poll callback again and no rx/tx
interrupts to be fired either.
Fix that by only accounting the rx work done in the poll callback.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're getting IRQs after lots of resources are already
allocated:
* netdev
* clocks
* MDIO bus
Also HW gets initialized by the time when checking IRQs as well.
Now there's a possibility for master interrupt controller to be not
probed yet. This will lead to exit from GMAC probe routine with "-
EPROBE_DEFER" and so deferred probe will hapen later on.
But since we exited the first GMAC probe without release of all
allocated resources there could be conflicts on subsequent probes.
For example this is what happens for me:
--->8---
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 20005c7a at 1 IRQ POLL (stmmac-0:01) active
platform e0018000.ethernet: Driver stmmaceth requests probe deferral
...
...
...
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x4e/0x68()
sysfs: cannot create duplicate filename
'/devices/platform/axs10x_mb/e0018000.ethernet/mdio_bus/stmmac-0'
CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.0.0-rc1-next-20150303+#8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
sysfs_warn_dup+0x4e/0x68
sysfs_create_dir_ns+0x98/0xa0
kobject_add_internal+0x8c/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at lib/kobject.c:240
kobject_add_internal+0x218/0x2e8()
kobject_add_internal failed for stmmac-0 with -EEXIST, don't try to
register things with the same name in the same di.
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W
4.0.0-rc1-next-20150303+ #8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
kobject_add_internal+0x218/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be2 ]---
libphy: mii_bus stmmac-0 failed to register
: Cannot register as MDIO bus
stmmac_pltfr_probe: main driver probe failed
stmmaceth: probe of e0018000.ethernet failed with error -22
--->8---
Essential fix is to check for IRQs availability as early as possible and
then safely go to deferred probe if IRQs are not there yet.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics registers have write-clear behaviour, which means we
will lose any increment between the read and write. Mitigate this by
only clearing when we read a non-zero value, so we will never falsely
report a total of zero. This also saves time as we only handle
error statistics here and they won't often be incremented.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many different sets of registers implemented by the
different versions of this controller, and we can only expect this to
get more complicated in future. Limit how much ethtool needs to know
by including an explicit bitmap of which registers are included in the
dump, allowing room for future growth in the number of possible
registers.
As I don't have datasheets for all of these, I've only included
registers that are:
- defined in all 5 register type arrays, or
- used by the driver, or
- documented in the datasheet I have
Add one new capability flag so we can tell whether the RTRATE
register is implemented.
Delete the TSU_ADRL0 and TSU_ADR{H,L}31 definitions, as they weren't
used and the address table is already assumed to be contiguous.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we may silently read/write a register at offset 0. Change
this to WARN and then ignore the write or read-back all-ones.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on the R8A7790, RFS8 reflects the RINT8 (multicast) MAC
status flag.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all firmware revisions have a proper
multi-interface client powersaving implementation,
e.g. qca6174 WLAN.RM.2.0-00073.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6184 WLAN.RM.2.0-00073 has a bug in sta
powersave state machine and requires peer param to
be poked to enable the powersave.
Calling this unconditionally should be safe for
other chips/firmwares.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During wmm tests changing wmm parameters did not change anything.
This was because of mismatch in WMM params per vdev command.
WMM params per vdev uses different command structure than wmm params
per pdev command.
Patch concerns qca6174.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 WLAN.RM.2.0-00073 firmware uses full rx
reordering offload and delivers Rx via a new HTT
event. The event however is incorrectly generated
in firmware and becomes overly long (with trailing
garbage). This was hitting defined CE buffer limit
that was programmed to the device and caused
device to crash upon busier Rx traffic.
Increasing the CE buffer limit for HTT Rx pipe to
2KBytes seems to be enough to workaround this
problem.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Header file was in arch dependent location arch/blackfin/include/asm/bfin_can.h,
Now move and merge the useful contents of header file into driver code, note
the original header file is reserved for full registers set access test by other
code so it survives.
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Blackfin was built without MMU, old driver code access the IO space by
physical address, introduce the ioremap approach to be compitable with
the common style supporting MMU enabled arch.
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace the blackfin arch dependent style of bfin_read/bfin_write with
common readw/writew
Signed-off-by: Aaron Wu <Aaron.wu@analog.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-03-03
This series contains updates to fm10k, i40e and i40evf.
Matthew updates the fm10k driver by cleaning up code comments and whitespace
issues. Also modifies the tunnel length header check, to make it more robust
by calculating the inner L4 header length based on whether it is TCP or UDP.
Implemented ndo_features_check() that allows drivers to report their offload
capabilities per-skb.
Neerav updates the i40e driver to skip over priority tagging if DCB is not
enabled. Fixes an issue where the driver is not flushing out the
DCBNL app table for applications that are not present in the local DCBX
application configuration TLVs. Fixed i40e where, in the case of MFP
mode, the driver was returning the incorrect number of traffic classes
for partitions that are not enabled for iSCSI. Even though the driver
was not configuring these traffic classes in the transmit scheduler for
the NIC partitions, it does use this map to setup the queue mappings.
Shannon updates i40e/i40evf to include the firmware build number in the
formatted firmware version string.
Akeem adds a safety net (by adding a 'default' case) for the possible
unmatched switch calls.
Mitch updates i40e to not automatically disable PF loopback at runtime,
now that we have the functionality to enable and disable PF loopback. This
fix cleans up a bogus error message when removing the PF module with VFs
enabled. Adds a extra check to make sure that the indirection table
pointer is valid before dereferencing it.
Anjali enables i40e to enable more than the max RSS qps when running in a
single TC mode for the main VSI. It is possible to enable as many as
num_online_cpus(). Adds a firmware check to ensure that DCB is disabled for
firmware versions older than 4.33. Updates i40e/i40evf to add missing
packet types for VXLAN offload. Updated i40e to be able to handle varying
RSS table size for each VSI, since all VSI's do not have the same RSS table
size.
v2: Dropped previous patch #9 "i40e/i40evf: Add capability to gather VEB
per TC stats" since the stats should be in ethtool and not debugfs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Miscellanea:
Add #include <linux/etherdevice.h>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Miscellanea:
Add #include <linux/etherdevice.h> where appropriate
Use ETH_ALEN instead of 6
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Module dependencies are broken in the case where CONFIG_I40E=y and
CONFIG_CONFIGFS_FS=m. This fixes the broken dependency.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the ax25 stack calls dev_queue_xmit it always calls
ax25_type_trans which sets skb->protocol to ETH_P_AX25.
Which means that by looking at the protocol type it is possible to
detect IP packets that have not been munged by the ax25 stack in
ndo_start_xmit and call a function to munge them.
Rename ax25_neigh_xmit to ax25_ip_xmit and tweak the return type and
value to be appropriate for an ndo_start_xmit function.
Update all of the ax25 devices to test the protocol type for ETH_P_IP
and return ax25_ip_xmit as the first thing they do. This preserves
the existing semantics of IP packet processing, but the timing will be
a little different as the IP packets now pass through the qdisc layer
before reaching the ax25 ip packet processing.
Remove the now unnecessary ax25 neighbour table operations.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6ce29b0e2a ("gianfar: Avoid unnecessary reg accesses in adjust_link()")
eliminates unnecessary calls to adjust_link for phy devices which don't support
interrupts and need polling. As part of that work, the 'new_state' local flag,
which was used to reduce logging noise on the console, was eliminated.
Unfortunately, that means that a 'Link is Down' log message will now be
issued continuously if a link is configured as UP, the link state is down,
and the associated phy requires polling. This occurs because priv->oldduplex
is -1 in this case, which always differs from phydev->duplex. In addition,
phydev->speed may also differ from priv->oldspeed. gfar_update_link_state()
is therefore called each time a phy is polled, even if the link state did not
change.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function that will enable changing the MAC address
of an ibmveth interface while it is still running.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routine rtl_is_special_data() is supposed to identify packets that need to
use a low bit rate so that the probability of successful transmission is
high. The current version has a bug that causes all IPv6 packets to be
labelled as special, with a corresponding low rate of transmission. A
complete fix will be quite intrusive, but until that is available, all
IPv6 packets are identified as regular.
This patch also removes a magic number.
Reported-and-tested-by: Alan Fisher <acf@unixcube.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Cc: Alan Fisher <acf@unixcube.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was incorrectly detected as 2 GHz device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
cppcheck detected a buffer overflow:
[drivers/net/wireless/ath/wil6210/debugfs.c:634]: (error) Width 8
given in format string (no. 1) is larger than destination buffer
'cmd[8]', use %7s to prevent overflowing it.
For the current %8s sscanf we require cmd to be 9 chars long
so increase it by 1 byte to prevent the sscan overflow (rather
than reduce the %8s specifier to %7s as cppcheck recommends).
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* ath9k_mci_update_rssi() is required only for
cards that use MCI scheme. Make sure that it
is not called for 3-wire cards.
* Call ath9k_ps_wakeup() early since register
accesses are made in ath9k_mci_update_rssi().
* Fix usage of btcoex_lock to handle no_stomp_timer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure that the btcoex timers are started/stopped
properly for both 3-wire and MCI schemes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When disabling BTCOEX, clearing the wlanactive gpio line
is required only for pre-AR9003 cards.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit "ath9k_hw: remove ATH_BTCOEX_CFG_MCI" removed
MCI as a separate coex scheme, but we need it to
avoid fiddling with GPIO registers during
ath9k_init_btcoex() that are meant only for 3-wire
cards.
Cc: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The MCI configuration values are assigned
in ath9k_hw_btcoex_init_mci() which are used
by the MCI reset routine. When initializing
BTCOEX/MCI, ath_mci_setup() ends up using
uninitialized data. Fix this by setting up
the configuration parameters before issuing
a MCI reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath_init_btcoex_timer() always returns 0, so
checking for error conditions is not required.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add HAL_DEF_WOWLAN case in rtl92cu_get_hw_reg
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Features which are device specific are already updated in
interface specific initialization e.g. register_dev.
We should not initialize them in mwifiex_init_adapter();
else this would overwrite earlier settings.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
From the indenting, it seems like the READ_NEXT_PAIR() was supposed to
be inside the while loop.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The # flag in %X means print a 0X prefix. Remove the extra 0x prefix.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to add per-vif TX power capability cap per-packet TX power to vif
configured power if the latter is lower than per-rate TX power and mac80211
per-frame power. Use vif TX power if TPC has been disabled for current the
interface
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure the HW with highest TX power among all vif when HW TPC has been
enabled in order to add support to per-vif TX power capability. Use lowest
configured power among all interfaces when TPC is disabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HAL_RETRY_LIMIT_*
RESET_DELAY_8185
RT_IBSS_INT_MASKS
RT_AC_INT_MASKS
NUM_OF_*
BT_*,
MAX_{LINES,BYTES}_*,
*_THREE_WIRE
*_QUEUE related
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set The BT/WLAN priority weights correctly and make sure
that MCI_LNA_TAKE is sent only for cards that share
PA/LNA.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Handle MCI_STATE_INIT_GPM_OFFSET separately and do not
overload ar9003_mci_get_next_gpm_offset() with a special
case.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The LNA_TRANS message needs to be sent only for
chips which have shared PA/LNA.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use a subroutine to enable MCI debug statistics
if it is present in the global configuration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch makes sure that the antenna configuration
is used properly when setting AR_MCI_TX_CTRL.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The value programmed in the BTCOEX control register
is different for each chip. This patch adds support
for 2-ANT, 1-ANT solutions based on AR9565.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several new MCI parameters need to be handled for
new chips, add them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we fail to allocate the sched/gpm buffers when
initializing MCI, we bail out properly. Checking
them in ar9003_mci_reset() is unnecessary, so remove it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* remove support for -9.ucode
* new statitics API
* rate control improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uonl
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-03-01' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* add triggers for firmware dump collection
* remove support for -9.ucode
* new statitics API
* rate control improvements
Bump i40e to 1.2.10 and i40evf to 1.2.4
Change-ID: I48aa64df05fcc8356e7026f3a9e69ecf78d0c785
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of MFP mode the driver was returning incorrect number of TCs
for partitions that are not enabled for iSCSI. Though the driver does
not configure these TCs in the Tx scheduler for the NIC partitions;
it does use this map to setup the queue mappings.
This patch fixes this and keeps all the NIC partitions to the default
PF TC i.e. TC0.
Change-ID: Iede214c907e7bac1356e999049b9f642759512b3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow DCBNL operations in MFP mode to allow query of port DCB settings
via all the PFs and register iSCSI APP on iSCSI enabled PF.
Change-ID: I34cc39b4665d0a631847d4079350d3814f02381e
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an extra check to make sure that the indirection table pointer is
valid before dereferencing it.
Change-ID: I698adbf3daff03081d01f489dc95a9f1ad8b12f1
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With changes to default number of queue pairs that the interface comes up with
from 1 per online CPU to 1 per lan_msix, we need to make sure we recalculate
rss_size. We will now recalculate rss_size based on number of queues enabled in
the VSI.
Without this fix if the max_lan_msix < num_online_cpu we will be coming up
with fewer queues but will be populating rss_size based on num_online_cpus.
This will result in packets getting silently dropped because RSS LUT has queues
that are not enabled.
Change-ID: Ifac8796ce1be1758bb0c34f38dbf4a3a76621e76
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since all VSIs don't have the same RSS table size,
have one for each VSI instead of having a single define
for RSS table size
Change-ID: Ic2c7c66e4a389d4b6c8841a707510a9735041f02
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were missing a few packet types for VXLAN offload. This patch fixes
that.
Change-ID: I4b23aa0b08e40ed49d0df6c49a5ed9f2009b44ce
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where the driver is not flushing out the
DCBNL app table for applications that are not present in the local
DCBX application configuration TLVs.
Change-ID: I1f1ee04c81c145071b2ab15657546eb10b81fadb
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For FW < 4.33 DCB should be disabled.
Also Autoneg workaround to avoid Rx stall is still needed for FW < 4.33.
Change-ID: Iff36ad86be2f597e7701096014d6d094332a9a21
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When running in a single TC mode the HW can be configured to enable more
than max RSS qps for the Main VSI. This patch makes it possible to
enable as many as num_online_cpus().
ethtool -L can still be used to reconfigure number of qps
to a smaller value.
Change-ID: I3e2df085276982603d86dfd79477c0ada8d30b8f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we now have functionality to enable and disable PF loopback at
runtime, don't try to do it automatically. Removing this call also gets
rid of a bogus error message when removing the PF module with VFs
enabled.
Change-ID: Ic38652d8a3b9498d96113bfaa5ea7bad050862e9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds default case to handle unmatched switch calls.
Change-ID: Icd203570a1dc5322c1038f68b98a83195e8ad28c
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Include the FW build number in the formatted FW version string. In order
to fit within ethtool's 32 character limit, the etrack's unused high order
bits are trimmed as is the leading 0 for the NVM version. This leaves
us with 2 character left for if/when the etrack id goes to 5 hex chars
and the NVM major number goes to 2 chars.
Change-ID: Icb004c4b9b14a2f54dd200b467fcc1d7b9297308
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If DCB is not enabled priority tagging is not needed
so skip over that section.
Change-ID: Ia3f3fa07945b421259a9ca38329d6d1cbd6c6bcc
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a few silly typos in the code and checkpatch warnings in support of
general code cleanliness.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The introduction of ndo_features_check allows drivers to report their
offload capabilities per-skb. Implement this in fm10k to take advantage
of this new functionality.
Reported-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FM10000 host interface can only support up to 184 bytes when
performing tunnel offloads. Because of this, a check was added to
prevent the driver from attempting to feed a header to the hardware too
big for it to parse. Make this check a little more robust by calculating
the inner L4 header length based on whether it is TCP or UDP.
Cc: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
My previous fix to clear padding of short frames used skb->len as the
DMA length, assuming that skb_padto() extended skb->len to include the
padding. That isn't the case; we need to use skb_put_padto() instead.
(This wasn't immediately obvious because software padding isn't
actually needed on the R-Car H2. We could make it conditional on
which chip is being driven, but it's probably not worth the effort.)
Reported-by: "Violeta Menéndez González" <violeta.menendez@codethink.co.uk>
Fixes: 612a17a54b50 ("sh_eth: Fix padding of short frames on TX")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fd9af07c34.
The hardware manual states that the frame error and multicast bits are
copied to bits 9:0 of RD0, not bits 25:16. I've tested that this is
true for RFS1 (CRC error), RFS3 (frame too short), RFS4 (frame too
long) and RFS8 (multicast).
Also adjust a comment to agree with this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of RX ring underrun (RDE), we attempt to reset the software
descriptor pointers (dirty_rx and cur_rx) to match where the hardware
will read the next descriptor from, as that might not be the first
dirty descriptor. This relies on reading RDFAR, but that register
doesn't exist on all supported chips - specifically, not on the R-Car
chips. This will result in unpredictable behaviour on those chips
after an RDE.
Make this pointer reset conditional and assume that it isn't needed on
the R-Car chips. This fix also assumes that RDFAR is never exposed at
offset 0 in the memory map - this is currently true, and a subsequent
commit will fix the ambiguity between offset 0 and no-offset in the
register offset maps.
Fixes: 79fba9f517 ("net: sh_eth: fix the rxdesc pointer when rx ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When submitting a DMA descriptor, the active bit must be written last.
When reading a completed DMA descriptor, the active bit must be read
first.
Add memory barriers to ensure that this ordering is maintained.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the most cases the spi messages has a length of two. Currently we
always set the the len field to two before transmit a spi message. In
cases for read out/write in the frame buffer we need another len. This
patch use trx len two as default. For the frame buffer cases we restore
the trx len to two on success and failure. This will reduce the len
setting of two when it's already two.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups the referencing for the state change context
variable. The state change context should only set once and this is by
initial a state change. This patch will use the initial state change
variable in the complete handler of the state change by using the ctx
context which should be always the same like the initial state change
context.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By holding the irq variable inside at86rf230_state_change we can squash
some multiple dereferencing for getting irq num.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch refactor the receive handling into one function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
I had this variable because I thought it would be protected by
disable/enable irq but this is not true. It's protected by stop/wake
netdev queue which is called by ieee802154_xmit_complete.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce a transmit retry handling into at86rf230 transmit
path. Current behaviour is to wait the normal receive time if we want
to go into STATE_TX_ON when the transceiver is in STATE_BUSY_RX_AACK
which indicates that a frame is currently receiving. A non force state
change will not interrupt the the receiving state.
The current behaviour is that after the normal receive time we will
start a force change into STATE_TX_ON. With this patch we do seven
retries to go into STATE_TX_ON without forcing. After we hit the
AT86RF2XX_MAX_TX_RETRIES we will start the force state change.
This is a polling like method to go into STATE_TX_ON in times of maximum
receiving time.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there are no more users kill dev_rebuild_header and all of it's
implementations.
This is long overdue.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AX25 already has it's own private arp cache operations to isolate
it's abuse of dev_rebuild_header to transmit packets. Add a function
ax25_neigh_construct that will allow all of the ax25 devices to
force using these operations, so that the generic arp code does
not need to.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two sets of header operations are functionally identical remove
the duplicate definition.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two sets of header operations are functionally identical remove the
duplicate definition.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets which are sent from the selftest (ethtool) flow,
should not be passed to GRO stack but rather dropped by
the driver after validation. To achieve that, we disable
GRO for the duration of the selftest.
Fixes: dd65beac48 ("net/mlx4_en: Extend usage of napi_gro_frags")
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit mask for currently supported driver features (MLX4_UPDATE_QP_SUPPORTED_ATTRS)
of the update-qp command was defined twice (using enum value and pre-processor
define directive) and wrong.
The return value of the call to mlx4_update_qp() from within the SRIOV
resource-tracker was wrongly voided down.
Fix both issues.
issue: none
Fixes: 09e05c3f78 ('net/mlx4: Set vlan stripping policy by the right command')
Fixes: ce8d9e0d67 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-02
Here's the first bluetooth-next pull request targeting the 4.1 kernel:
- ieee802154/6lowpan cleanups
- SCO routing to host interface support for the btmrvl driver
- AMP code cleanups
- Fixes to AMP HCI init sequence
- Refactoring of the HCI callback mechanism
- Added shutdown routine for Intel controllers in the btusb driver
- New config option to enable/disable Bluetooth debugfs information
- Fix for early data reception on L2CAP fixed channels
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After TIPC doesn't depend on iocb argument in its internal
implementations of sendmsg() and recvmsg() hooks defined in proto
structure, no any user is using iocb argument in them at all now.
Then we can drop the redundant iocb argument completely from kinds of
implementations of both sendmsg() and recvmsg() in the entire
networking stack.
Cc: Christoph Hellwig <hch@lst.de>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't operate on PCI core, but PCI host device, so there is no
point of passing core related struct.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bringing PCIe hosted bus up requires operating on host-related core.
Since we plan to support PCIe Gen 2 devices we should provide a helper
picking the correct one (PCIE or PCIE2).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Starting with kernel 3.19 reason is provided by cfg80211.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently scan params structure has only active or passive dwell time
fields, passive one is used for fragmented scans too. FW needs the
passive dwell time even when performing fragmented scan for calculating
time between channels. Add a separate parameter for fragmented dwell time
and pass both fragmented and passive to FW.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Lots of issues can be caught when the RSSI drops. Add the
ability to collect the firmware data at that point.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It can be very useful to monitor the statistics and trigger
a firmware dump when a certain value hits a certain offset.
Since the statistics are huge, add a generic trigger. When
the DWORD at offset X reaches value Y.
Since there is another trigger before this one I can't add
right now because of a dependency on mac80211, add a
reserved entry to keep the enum in place.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sometimes the firmware will have a hard coded configuration.
In this case, the driver won't find any configuration
in the firmware file, and it will have to re-start
recording in case it has been stopped. This can't be done
by the configuration host command since there is no such
host command configured. Do that with the registers instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This will allow to collect the data as soon the firmware
sends a specific notification of command response.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We fire the trigger when the channel switch starts, but
the delay is configurable. That makes is easier to catch
channel switches that fail.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Missing beacons is a good indication that something is going
wrong in the firmware. Add a trigger to be able to collect
data when we start missing beacons with a configurable
threshold.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Now that the firmware dump can be triggered by events in
the code and not only the user or an firmware ASSERT, we
need a way to know why the firmware dump was triggered.
Add a section in the dump file for that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Most of the time, the issues we want to debug with the
firmware dump mechanism are transient. It is then very
hard to stop the recording on time and get meaningful
data.
In order to solve this, I add here an infrastucture
of triggers. The user will supply a list of triggers
that will start / stop the recording. We have two types
of triggers: start and stop. Start triggers can start a
specific configuration. The stop triggers will be able to
kick the collection of the data with the currently running
configuration. These triggers are given to the driver by
the .ucode file - just like the configuration.
In the next patches, I'll add triggers in the code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
20 ms fragments are no longer required by system.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Packet Level Co-Running is a BT Coex feature which is
supported on certain devices only, hence the need for
a TLV flag for it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We shouldn't call iwl_mvm_d3_disconnect_iter() on the running
interfaces when we are woken up due to net-detect, because it doesn't
make sense. Additionally, this seems to set the
IEEE80211_SDATA_DISCONNECT_RESUME flag that will cause a disconnection
on the next resume (if a normal WoWLAN is used).
To solve this, skip the iteration loop when net-detect is set.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reported-by: Samuel Tan <samueltan@chromium.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When a PADT frame is received, the socket may not be in a good state to
close down the PPP interface. The current implementation handles this by
simply blocking all further PPP traffic, and hoping that the lack of traffic
will trigger the user to investigate.
Use schedule_work to get to a process context from which we clear down the
PPP interface, in a fashion analogous to hangup on a TTY-based PPP
interface. This causes pppd to disconnect immediately, and allows tools to
take immediate corrective action.
Note that pppd's rp_pppoe.so plugin has code in it to disable the session
when it disconnects; however, as a consequence of this patch, the session is
already disabled before rp_pppoe.so is asked to disable the session. The
result is a harmless error message:
Failed to disconnect PPPoE socket: 114 Operation already in progress
This message is safe to ignore, as long as the error is 114 Operation
already in progress; in that specific case, it means that the PPPoE session
has already been disabled before pppd tried to disable it.
Signed-off-by: Simon Farnsworth <simon@farnz.org.uk>
Tested-by: Dan Williams <dcbw@redhat.com>
Tested-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2 driver uses .ndo_fix_features to force enable of Rx VLAN tag
stripping when the card cannot disable it. The driver should remove
NETIF_F_HW_VLAN_CTAG_RX flag from hw_features instead so it is fixed
for the ethtool.
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add *_SIZE macros for the bits ENDIA_DESC and
ENDIA_PKT
Signed-off-by: Arun Chandran <achandran@mvista.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Program management descriptor's access mode according to the
dynamically detected CPU endianness.
Signed-off-by: Arun Chandran <achandran@mvista.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows for packet parsing to be done by the fast path. This performance
optimization already exists for IPv4. Add similar logic for IPv6.
Signed-off-by: Amitabha Banerjee <banerjeea@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 60b4ea1781 ("net: systemport: log RX buffer allocation and RX/TX DMA
failures") added a few software maintained statistics using
BCM_SYSPORT_STAT_MIB_RX and BCM_SYSPORT_STAT_MIB_TX. These statistics are read
from the hardware MIB counters, such that bcm_sysport_update_mib_counters() was
trying to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCM_SYSPORT_STAT_SOFT, similar to
BCM_SYSPORT_STAT_NETDEV, such that bcm_sysport_get_ethtool_stats will read from
the software mib.
Fixes: 60b4ea1781 ("net: systemport: log RX buffer allocation and RX/TX DMA failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 44c8bc3ce3 ("net: bcmgenet: log RX buffer allocation and RX/TX dma
failures") added a few software maintained statistics using
BCMGENET_STAT_MIB_RX and BCMGENET_STAT_MIB_TX. These statistics are read from
the hardware MIB counters, such that bcmgenet_update_mib_counters() was trying
to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCMGENET_STAT_SOFT, similar to
BCMGENET_STAT_NETDEV, such that bcmgenet_get_ethtool_stats will read from the
software mib.
Fixes: 44c8bc3ce3 ("net: bcmgenet: log RX buffer allocation and RX/TX dma failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 'mutliple' to 'multiple'
Change 'Firmare' to 'Firmware'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
cpsw_suspend/resume calbacks under CONFIG_PM_SLEEP
to avoid build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a dev_pm_ops suspend_late/resume_early pair but not a
set of hibernation functions means those pm functions will
not be called upon hibernation.
Fix this by using SET_LATE_SYSTEM_SLEEP_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
davinci_mdio_x callbacks under CONFIG_PM_SLEEP to avoid build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new API slightly changes the layout of the version of
the firmware - prepare for that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Report the average beacon signal and the number of received beacons as
measured by the firmware.
Since the firmware just counts, and doesn't reset the counter at all,
clear it in the firmware whenever we associate. However, accumulate it
over firmware restart.
Since clearing the statistics in the firmware will also clear the ones
for the radio statistics, add those to the accumulator when cleared.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Due to HW bug in the DBGC when driver want to stop the dbg recording it
should wait 100us before collecting the data instead of write 0 to
DBGC_OUT_CTRL.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The legacy scan API is deprecated and not used anymore with 10 and
higher firmware versions. Since we deprecated firmware version 9, we
can remove a whole lot of unused code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This firmware is not supported anymore. Stop loading this firmware.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Export the radio statistics from the statistics v10 API (if the
firmware also has the capability to fill these statistics) using
the global survey data facility.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
New firmware versions will report statistics using a new version 10
of the API, instead of the current version 8. Add support for this.
This enables getting beacon and radio statistics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to use the firmware debugging system even when
the configuration values are set hard coded in the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The shared antenna should be forbidden to use only if there's
high BT activity. Comparing to BT_OFF was effectively causing
us to always forbid using the shared antenna for SISO. This
leads to degraded performance in scenarios where the shared
antenna would have better performance.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add this to the info printed when reading rate_scale_table.
Useful for debugging.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ss_force is a debugging option to force a certain single stream
tx mode. It's not useful if it gets reset after tx idle. Fix that.
While at it also make sure any code touching ss_force will only
get compiled if debugfs support is configured.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Newer devices have more PAPD channel groups.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When a TDLS station is being drained its Tx queues are still in use. Don't
allocate them to a different station in the meantime.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Due to issues with Miracast adapters MIMO reception disable
use of MIMO when for low latency P2P traffic.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Once the FW supports autonomous decision between STBC/BFER/SISO
we no longer set the STBC bit and ANT_AB in the rate table.
However the FW rate in the tx response will have the STBC
or BFER bit set and the antennas set to ANT_AB in case these
were chosen by it. This will cause us to discard any such
response as unmatching the current LQ table and thus break
the rs search cycle completely.
Fix this by relaxing the rate matching in case we're working
with the new API and STBC/BFER are used.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The check to avoid the shared antenna was passed the wrong
antenna parameter. It should have checked whether the antenna of
the next column we're considering is allowed and instead it was
passed the current antenna.
This could lead to a wrong choice of the next column in the rs
algorithm and non optimal performance.
Fixes: commit 219fb66b49 ("iwlwifi: mvm: rs - don't use the shared antenna when BT load is high")
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Commit 740c7f31c0 ("sh_eth: Ensure DMA engines are stopped before
freeing buffers") added a call to sh_eth_reset() to the
sh_eth_set_ringparam() and sh_eth_close() paths.
However, setting the software reset bit(s) in the EDMR register resets
the MAC Address Registers to zero. Hence after kexec, the new kernel
doesn't detect a valid MAC address and assigns a random MAC address,
breaking DHCP.
Set the MAC address again after the reset in sh_eth_dev_exit() to fix
this.
Tested on r8a7740/armadillo (GETHER) and r8a7791/koelsch (FAST_RCAR).
Fixes: 740c7f31c0 ("sh_eth: Ensure DMA engines are stopped before freeing buffers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds bcmgenet_tx_poll for the tx_rings. This can reduce the
interrupt load and send xmit in network stack on time. This also
separated for the completion of tx_ring16 from bcmgenet_poll.
The bcmgenet_tx_reclaim of tx_ring[{0,1,2,3}] operative by an interrupt
is to be not more than a certain number TxBDs. It is caused by too
slowly reclaiming the transmitted skb. Therefore, performance
degradation of xmit after 605ad7f ("tcp: refine TSO autosizing").
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brian reported crashes using IPv6 traffic with macvtap/veth combo.
I tracked the crashes in neigh_hh_output()
-> memcpy(skb->data - HH_DATA_MOD, hh->hh_data, HH_DATA_MOD);
Neighbour code assumes headroom to push Ethernet header is
at least 16 bytes.
It appears macvtap has only 14 bytes available on arches
where NET_IP_ALIGN is 0 (like x86)
Effect is a corruption of 2 bytes right before skb->head,
and possible crashes if accessing non existing memory.
This fix should also increase IPv4 performance, as paranoid code
in ip_finish_output2() wont have to call skb_realloc_headroom()
Reported-by: Brian Rak <brak@vultr.com>
Tested-by: Brian Rak <brak@vultr.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
four-way-handshake problem. The others are various small fixes
for problems all over, nothing really stands out.
-----BEGIN PGP SIGNATURE-----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=H3+7
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few patches have accumulated, among them the fix for Linus's
four-way-handshake problem. The others are various small fixes
for problems all over, nothing really stands out.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for reporting the actual and maximum combined channels
count of the hv_netvsc driver via 'ethtool --show-channels'.
This required adding 'max_chn' to 'struct netvsc_device', and assigning
it 'rsscap.num_recv_que' in 'rndis_filter_device_add'. Now we can access
the combined maximum channel count via 'struct netvsc_device' in the
ethtool callback.
Signed-off-by: Andrew Schwartzmeyer <andrew@schwartzmeyer.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, sending a packet with the source MAC address of one
of the CPSW interfaces to one of the CPSW slave ports while it's configured in
dual_emac mode would update the port_num field of the VLAN/Unicast Address
Table Entry. This would cause it to discard all incoming traffic addressed to
that MAC address, essentially rendering the port useless until the ALE table is
cleared (by starting and stopping the interface or rebooting.)
For example, if eth0 has a MAC address of 90:59:af:8f:43:e9 it will have
an ALE table entry:
00 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=0 addr=90:59:af:8f:43:e9)
If you configure another device with the same MAC address and connect it
to the first CPSW slave port and send some traffic the ALE table entry
becomes:
04 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=1 addr=90:59:af:8f:43:e9)
>From this point forward all incoming traffic addressed to
90:59:af:8f:43:e9 will be dropped.
Setting the SECURE bit for the VLAN/Unicast address table entry for each
interface's MAC address corrects the problem.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a discrepancy here because the niu_class_to_ethflow() returns
zero on failure and one on success but the caller expected zero on
success and negative on failure.
The problem means that we allow the user to pass classes and flow_types
which we don't want. I've looked at it a bit and I don't see it as a
very serious bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smc91x driver traditionally gets configured at compile-time
for whichever hardware it runs on. This no longer works on
ARM as we continue to move to building all-in-one kernels.
Most ARM configurations with this driver already use run-time
configuration through DT or through platform_data, but a
few have not been converted yet.
I've checked all ARM boards that use this driver in their
legacy board files, and converted the ones that were using
compile-time configuration in smc91x.h to behave like the
other ones and provide the interrupt polarity along with
the MMIO configuration (width, stride) at platform device
creation time.
In particular, these combinations were previously selectable
in Kconfig but in fact broken:
- sa1100 assabet plus pleb
- msm combined with any other armv6/v7 platform
- pxa-idp combined with any non-DMA pxa variant
- LogicPD PXA270 combined with any other pxa
- nomadik combined with any other armv4/v5 platform,
e.g. versatile.
None of these seem critical enough to warrant a backport
to stable, but it would be nice to clean this up for good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
----
I would like the patch to get merged through netdev, after
Robert and/or Linus have verified it on at least some hardware.
There are a few other non-ARM platforms using this driver,
I could do the same patch for those if we want to take
it further.
arch/arm/mach-msm/board-halibut.c | 8 ++++-
arch/arm/mach-msm/board-qsd8x50.c | 8 ++++-
arch/arm/mach-pxa/idp.c | 5 +++
arch/arm/mach-pxa/lpd270.c | 8 ++++-
arch/arm/mach-realview/core.c | 7 ++++
arch/arm/mach-realview/realview_eb.c | 2 +-
arch/arm/mach-sa1100/neponset.c | 6 ++++
arch/arm/mach-sa1100/pleb.c | 7 ++++
drivers/net/ethernet/smsc/smc91x.c | 9 +++--
drivers/net/ethernet/smsc/smc91x.h | 114 ++----------------------------------------------------------
10 files changed, 57 insertions(+), 117 deletions(-)
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-02-26
This series contains fixes for i40e and i40evf only.
Alexey Khoroshilov found a possible leak of 'cmd_buf' when copy_from_user()
failed in i40e_dbg_command_write(), so resolved by calling kfree().
Shannon provides a fix to ensure the shift and bitwise precedences do not
work backwards for us by adding parans. Fixed the driver by preventing
the driver from allowing stray interrupts or causing system logs from
un-handled interrupts by combining the ICR0 shutdown with the standard
interrupt shutdown and add the interrupt clearing to the PCI shutdown
path. Fixed an issue where a NVM write times out before a transaction
can complete, so Shannon added logic to make another attempt by
reacquiring the semaphore, then retry the write, if the one retry fails,
we will then give up. Adds checks to pointers before their use to ensure
we do not try to dereference NULL pointers when returning values from the
AdminQ calls.
Akeem adds a check to bail out if the device is already down when checking
for Tx hang subtask.
Anjali fixes TSO with more than 8 frags per segment issue. The hardware
has some limitations which the driver needs to adhere to:
1) no more than 8 descriptors per packet on the wire
2) no header can span more than 3 descriptors
If one of these events happens, the hardware will generate an internal
error and freeze the Tx queue, so Anjali fixes this by linearizes the skb
to avoid these situations. Fixed an issue where the per Traffic Class
queue count was higher than queues enabled, which will fix a warning
with multiple function mode where systems regularly have more cores than
vectors. Fixed TCP/IPv6 over VXLAN Tx checksum offload, where we were
checking the outer protocol flags and deciding the flow for the inner
header.
Jesse fixes a race condition in the transmit hang detection. Before we
were having issues of false Tx hang detection, no the driver makes more
direct with the checks for progress forward by directly checking the head
write back address and tail register when determining progress. This
avoids Tx hangs where the software gets behind, because we are directly
checking hardware state when determining a hang state.
Neerav fixes the transmit ring Qset handle when DCB reconfigures. The issue
was when DCB is reconfigured to a single traffic class (TC) and the driver
did not reset the Tx ring Qset handle to correct the mapping, which caused
the Tx queue to disable timeouts. Also as part of DCB reconfiguration flow
if the Tx queue disable times out, then issue a PF reset to do some level
of recovery.
Mitch stops flow director on shutdown because, in some cases, the hardware
would continue to try to access the FDIR ring after entering D3Hot state,
which would cause either PCIe errors or NMIs, depending upon the system
configuration.
* NOTE * I have verified that this series of patches for net will not cause
any merge issues when you sync up your net tree with your net-next tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the hardware may not have been properly shutdown
before this driver gets control, through use by firmware, for example.
Until the driver is loaded, interrupts associated with the hardware
could go pending. When the IRQs are requested napi support has not
been initialized yet, but the ISR will get control and schedule napi
processing resulting in a kernel panic because the poll routine has not
been set.
Adjust the code so that the driver is fully ready to handle and process
interrupts as soon as the IRQs are requested. This involves requesting
and freeing IRQs during start and stop processing and ordering the napi
add and delete calls appropriately.
Also adjust the powerup and powerdown routines to match the start and
stop routines in regards to the ordering of tasks, including napi
related calls.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "Sitecom Europe B.V. LN-028 Network USB 2.0 Adapter".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows TSO being set/unset on the master, so that GSO
segmentation is done after team layer.
Similar patch is present for bonding:
b0ce3508b2 ("bonding: allow TSO being set on bonding master")
and bridge:
f902e8812e ("bridge: Add ability to enable TSO")
Suggested-by: Jiri Prochazka <jprochaz@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
"val" is declared as a u64 so static checkers complain that this shift
can wrap. I don't have the hardware but probably it's doesn't have over
31 ports. Still we may as well silence the warning even if it's not a
real bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure kmalloc() succeeds.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reads and writes to adapter memory via the PCI-E Memory Window
interface, data gets swizzled on 4-byte boundaries on Big-Endian systems
because we need to account for the register read/write interface which
incorporates a swizzle onto the Little-Endian PCI-E Bus.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should complete notify_check before returning the credits. Once we return the
credits, adaptor may access the notify data.
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing I experience a deadlock while using the at86rf233 on a
raspberry pi. The reason was an edge triggered gpio irq because the irq
triggered while irq was disabled. This issue doesn't happend on a level
triggered irq because the irq will hit after calling enable_irq.
This patch adds a warning that it's not recommended to use a edge-triggered
irq type. Also change the examples to high-level irqtype.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The at86rf2xx chips supports the setting of irq polarity if active low
or active high. This patch adds a handling for IRQ_ACTIVE_LOW if the
irq_type is IRQ_TYPE_LEVEL_LOW.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we support at86rf233 we need to ensure that basic operation
default values are the same. This patch always sets IRQ_MASK_MODE to 0
which is after reset 1 at the at86rf233 and 0 at the at86rf231.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes tx_timeout handling. We used it in sync xmit
handling. Since we support async xmit handling a xmit timeout handling
isn't easy to implement and should be implemented by netdev watchdog
mechanism.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for setting the xtal trim register. Some at86rf2xx
transceiver boards needs fine tuning the xtal capacitor.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch copies the platform data in driver allocated space at first.
With this change we ensure that we access the allocated platform data as
readonly space.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For the STA interface, track 'privacy'.
Refactor safety checks to:
- always print connection params
- always check IE size validity
- require RSN IE for secure connection
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make this field to track privacy attribute for all interface types
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some platforms get_cycles() implemented to allways return 0.
On such platforms "Division by zero" bug was triggered.
Signed-off-by: Boris Sorochkin <boriss@codeaurora.org>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change threshold to be variable debugfs entry from hard-coded 0.
Default threshold value is 16 descriptors because HW is capable
of fetching up to 16 descriptors at once.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mark expected branches using likely()/unlikely().
Do it on high performance route - data path and interrupts
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the old hardware, bug existed that caused DA and SA for every
Rx packet to be swapped in the AP mode.
New hardware has fix for this bug. Enable this fix in the
hardware.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hardware older than Sparrow B0 obsolete.
There is no WiFi product that uses this hardware.
Recent firmware does not support it either.
Remove driver support.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce boot loader. Instead of the operational firmware,
very small boot loader is burned to the on-board flash. Boot loader
initializes hardware upon reset, and prepares for low power mode.
Boot loader reports MAC address and detects radio chip connected.
Driver loads firmware only when bringing up interface. All information
required to set up network interface, most important is MAC address,
reported by the boot loader
The firmware composed of 2 files:
- wil6210.fw - firmware itself (compiled code + data)
- wil6210.board - board file (various board and radio dependent
calibrations and parameters)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 84b313b35f ("mwifiex: make tx packet 64 byte DMA aligned")
induced payload offset issue for USB interface.
There is no USB interface header for tx packets, so there's no need to
pull interface length while processing tx skb.
This patch fixes this issue.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for DMA alignment of sk_buffs
allocated for RX.
Patch also adds support to modify skb allocation flags.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Qingshui Gao <gaoqs@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW crash has been observed while running iperf TX with SD8887
devices. This is because of invalid TX buffer setting. SD8887
supports 2K buffer sizes. This patch fixes this issue.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch changes datatypes for device capability flags to bool.
Patch also aggregates these variables at single place.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes a crash which was happening because of RX of
management frames on uninitialzed interface. Now we drop management
frames for interfaces where cfg80211 has not registered any management
subtype reception or interface has no NL80211 iftype set.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch handles a corner case where TX packet would remain in
driver queue till next packet comes in.
Here is sequence:
1. TX packet is queued via hard_start_xmit and main_work is queued
2. SDIO interrupt comes in which directly call mwifiex_main_process.
This starts executing main superloop.
3. Now work from step1 is scheduled but at first check itself it sees
mwifiex_processing is set and exits.
4. Now if superloop from step2 has passed TX processing part of superloop
this packet would remain in queue until next packet/command/SDIO interrupt
arrives and queues main_work.
This patch fixes this corner case by defining more_task flag which is set when
mwifiex_processing is found to be true. At end of superloop we again check if
more_task flag is set and if set, execute superloop again.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Debugfs_remove will check for error or NULL for us, so it is not
necessary to do this here.
Signed-off-by: Bas Peters <baspeters93@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Delete SET_USB_STOP macro and rtl_usb_deinit because
those are called twice in USB de-initialize routine.
Add some de-initialize workqueue function in USB disconnect routine.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cleanup the port forwarding state transitions for the cases when the port
joins or leaves a bridge, or is brought admin UP or DOWN. When port is
bridged, we can rely on bridge driver putting port in correct state using
STP callback into port driver, regardless if bridge is enabled for STP or not.
When port is not bridged, we can reuse some of the STP code to enabled or
disable forwarding depending on UP or DOWN.
Tested by trying all the transitions from bridge/not bridge, and UP/DOWN, and
verifying port is in the correct forwarding state after each transition.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a rename of physical ports from "lport" to "pport". Not a
functional change. OF-DPA uses logical ports (lport) for tunnels, but the
driver (and device) were using "lport" for physical ports. Renaming physical
ports references to "pport", freeing up "lport" for use later with tunnels.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rocker device returns error codes if something goes wrong with descriptor
processing. Originally the device used standard errno codes for different
errors, but since those errno codes aren't portable across ARCHs, the device
now returns hard-coded error codes that stay constant across diff ARCHs. Fix
driver to use those same hard-coded values.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device is a dongle made by Philips to enhance their TVs with wireless capabilities,
but works flawlessly on any upstream kernel, provided that the ath9k_htc module is attached to it.
It's correctly recognized by lsusb as "0471:209e Philips (or NXP) PTA01 Wireless Adapter" and the
patch has been tested on real hardware.
Signed-off-by: Leon Nardella <leon.nardella@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All hw driver components in the rtlwifi driver, except for the
rtl8192de component has this bug. They would clear BE bit in the
ACM_CTRL register instead of the VO bit when processing the VO queue.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some rare circumstances the escan protection timer can expire
before the setup completed (due to long timeouts on IOCTL). This
patch avoids this situation by setting the timer after the setup
completed correctly.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SDIO watchdog will put the device in sleep mode when there is
no activity for some time and nothing to do anymore. This check
is incomplete and should also check if there is a control frame
to transmit.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Borrowed the idea of the PM freezer to make sdio suspend wait for
watchdog and DPC thread to freeze at a safe point in their thread
routine. The suspend takes 20-25 msec.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the revision info visible in debugfs. The new debugfs
file is named 'revinfo'.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a key is set or cleared with an unsupported key index then
brcmfmac will print an error. With most wpa_supplicants this is
happening a lot. The error print is confusing and not needed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Changing the SDIO state of the driver involves changing the bus
interface state. Adding a helper function makes sure that knowledge
is in one place.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
alloc_workqueue() has string format formation ability e.g. wqname%ifname
will be treated as wqnameifname. Use this and remove string operations
while defining strings for workqueue names.
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
the if/elseif/else is exhaustive - there is no 4th case given the
rssi_ctrl_mask = RADIO_2055_NBRSSI_SEL | RADIO_2055_WBRSSI_G1_SEL |
RADIO_2055_WBRSSI_G2_SEL;
so this unreachable else case (dead code) can be dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When coming out of WoW sleep, check and restart
timers based on TSF2.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The events for patterns 8..15 need to be
cleared on wakeup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Handle the user-configured patterns in the range 8..15
when waking up and update wow_status correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The power save state of MCI has to be disabled
when enabling WoW sleep, check this properly.
ar9003_mci_state() doesn't handle MCI_STATE_GET_WLAN_PS_STATE
right now, but this will be done later when proper
support for MCI/PS is added.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several new MCI states have to handled,
add them to the list.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When MCI is enabled and WoW sleep is enabled,
make sure that the RTC keep awake timer is set
with the required value. This is also required
when the AR_WA is programmed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Along with AR9462, AR9565 also has an extra field
in the TX descriptor which needs to be zeroed out
for the keep alive frame. This makes the earlier
REG_WRITE redundant, so it can be removed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure we don't try to dereference NULL pointers when returning values
from the AdminQ calls.
Change-ID: Ia6694f2f415d50acf0aba063c863568742799aff
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, a multi-write transaction takes longer than the
default 3 minute timeout on the write semaphore. If the write failed with
an EBUSY status, this is likely the problem, so here we try to reacquire
the semaphore then retry the write. We only do one retry, then give up.
Change-ID: I1c8be60688acc2f39573839579baf601207c4a36
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some cases, the hardware would continue to try to access the FDIR
ring after entering D3Hot state, which would cause either PCIe errors or
NMIs, depending upon system configuration.
Explicitly stop FDIR in our shutdown routine to eliminate this
possibility.
Change-ID: I1bd9fc7fd8f151fe24cad132ac9adddab923e3af
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Combine the ICR0 shutdown with the standard interrupt shutdown, and
add the interrupt clearing to the PCI shutdown path.
This prevents the driver from allowing stray interrupts or causing
system logs from un-handled interrupts.
Change-ID: I48f6ab95cad7f8ca77c1f26c92a51cc1034ced43
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were checking the outer Protocol flags and deciding the flow for
inner header. This patch fixes that.
This fixes the Tx checksum offload for TCP/IPv6 over vxlan.
Change-ID: I837aaea921d34f71b24c2bc32aaadea5001ddf78
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
