Several spots in the kernel perform a sequence like:
skb_queue_tail(&sk->s_receive_queue, skb);
sk->sk_data_ready(sk, skb->len);
But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up. So this skb->len access is potentially
to freed up memory.
Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.
And finally, no actual implementation of this callback actually uses
the length argument. And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.
So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.
Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of tcp, gso_size contains the tcpmss.
For UFO (udp fragmentation offloading) skbs, gso_size is the fragment
payload size, i.e. we must not account for udp header size.
Otherwise, when using virtio drivers, a to-be-forwarded UFO GSO packet
will be needlessly fragmented in the forward path, because we think its
individual segments are too large for the outgoing link.
Fixes: fe6cc55f3a ("net: ip, ipv6: handle gso skbs in forwarding path")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more networking updates from David Miller:
1) If a VXLAN interface is created with no groups, we can crash on
reception of packets. Fix from Mike Rapoport.
2) Missing includes in CPTS driver, from Alexei Starovoitov.
3) Fix string validations in isdnloop driver, from YOSHIFUJI Hideaki
and Dan Carpenter.
4) Missing irq.h include in bnxw2x, enic, and qlcnic drivers. From
Josh Boyer.
5) AF_PACKET transmit doesn't statistically count TX drops, from Daniel
Borkmann.
6) Byte-Queue-Limit enabled drivers aren't handled properly in
AF_PACKET transmit path, also from Daniel Borkmann.
Same problem exists in pktgen, and Daniel fixed it there too.
7) Fix resource leaks in driver probe error paths of new sxgbe driver,
from Francois Romieu.
8) Truesize of SKBs can gradually get more and more corrupted in NAPI
packet recycling path, fix from Eric Dumazet.
9) Fix uniprocessor netfilter build, from Florian Westphal. In the
longer term we should perhaps try to find a way for ARRAY_SIZE() to
work even with zero sized array elements.
10) Fix crash in netfilter conntrack extensions due to mis-estimation of
required extension space. From Andrey Vagin.
11) Since we commit table rule updates before trying to copy the
counters back to userspace (it's the last action we perform), we
really can't signal the user copy with an error as we are beyond the
point from which we can unwind everything. This causes all kinds of
use after free crashes and other mysterious behavior.
From Thomas Graf.
12) Restore previous behvaior of div/mod by zero in BPF filter
processing. From Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: sctp: wake up all assocs if sndbuf policy is per socket
isdnloop: several buffer overflows
netdev: remove potentially harmful checks
pktgen: fix xmit test for BQL enabled devices
net/at91_ether: avoid NULL pointer dereference
tipc: Let tipc_release() return 0
at86rf230: fix MAX_CSMA_RETRIES parameter
mac802154: fix duplicate #include headers
sxgbe: fix duplicate #include headers
net: filter: be more defensive on div/mod by X==0
netfilter: Can't fail and free after table replacement
xen-netback: Trivial format string fix
net: bcmgenet: Remove unnecessary version.h inclusion
net: smc911x: Remove unused local variable
bonding: Inactive slaves should keep inactive flag's value
netfilter: nf_tables: fix wrong format in request_module()
netfilter: nf_tables: set names cannot be larger than 15 bytes
netfilter: nf_conntrack: reserve two bytes for nf_ct_ext->len
netfilter: Add {ipt,ip6t}_osf aliases for xt_osf
netfilter: x_tables: allow to use cgroup match for LOCAL_IN nf hooks
...
The purpose of this single series of commits from Srivatsa S Bhat (with
a small piece from Gautham R Shenoy) touching multiple subsystems that use
CPU hotplug notifiers is to provide a way to register them that will not
lead to deadlocks with CPU online/offline operations as described in the
changelog of commit 93ae4f978c (CPU hotplug: Provide lockless versions
of callback registration functions).
The first three commits in the series introduce the API and document it
and the rest simply goes through the users of CPU hotplug notifiers and
converts them to using the new method.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=SW7Q
-----END PGP SIGNATURE-----
Merge tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CPU hotplug notifiers registration fixes from Rafael Wysocki:
"The purpose of this single series of commits from Srivatsa S Bhat
(with a small piece from Gautham R Shenoy) touching multiple
subsystems that use CPU hotplug notifiers is to provide a way to
register them that will not lead to deadlocks with CPU online/offline
operations as described in the changelog of commit 93ae4f978c ("CPU
hotplug: Provide lockless versions of callback registration
functions").
The first three commits in the series introduce the API and document
it and the rest simply goes through the users of CPU hotplug notifiers
and converts them to using the new method"
* tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
net/iucv/iucv.c: Fix CPU hotplug callback registration
net/core/flow.c: Fix CPU hotplug callback registration
mm, zswap: Fix CPU hotplug callback registration
mm, vmstat: Fix CPU hotplug callback registration
profile: Fix CPU hotplug callback registration
trace, ring-buffer: Fix CPU hotplug callback registration
xen, balloon: Fix CPU hotplug callback registration
hwmon, via-cputemp: Fix CPU hotplug callback registration
hwmon, coretemp: Fix CPU hotplug callback registration
thermal, x86-pkg-temp: Fix CPU hotplug callback registration
octeon, watchdog: Fix CPU hotplug callback registration
oprofile, nmi-timer: Fix CPU hotplug callback registration
intel-idle: Fix CPU hotplug callback registration
clocksource, dummy-timer: Fix CPU hotplug callback registration
drivers/base/topology.c: Fix CPU hotplug callback registration
acpi-cpufreq: Fix CPU hotplug callback registration
zsmalloc: Fix CPU hotplug callback registration
scsi, fcoe: Fix CPU hotplug callback registration
scsi, bnx2fc: Fix CPU hotplug callback registration
scsi, bnx2i: Fix CPU hotplug callback registration
...
Currently we're checking a variable for != NULL after actually
dereferencing it, in netdev_lower_get_next_private*().
It's counter-intuitive at best, and can lead to faulty usage (as it implies
that the variable can be NULL), so fix it by removing the useless checks.
Reported-by: Daniel Borkmann <dborkman@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: stephen hemminger <stephen@networkplumber.org>
CC: Jerry Chu <hkchu@google.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly as in commit 8e2f1a63f2 ("packet: fix packet_direct_xmit
for BQL enabled drivers"), we test for __QUEUE_STATE_STACK_XOFF bit
in pktgen's xmit, which would not fully fill the device's TX ring for
BQL drivers that use netdev_tx_sent_queue(). Fix is to use, similarly
as we do in packet sockets, netif_xmit_frozen_or_drv_stopped() test.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old interpreter behaviour was that we returned with 0
whenever we found a division by 0 would take place. In the new
interpreter we would currently just skip that instead and
continue execution.
It's true that a value of 0 as return might not be appropriate
in all cases, but current users (socket filters -> drop
packet, seccomp -> SECCOMP_RET_KILL, cls_bpf -> unclassified,
etc) seem fine with that behaviour. Better this than undefined
BPF program behaviour as it's expected that A contains the
result of the division. In future, as more use cases open up,
we could further adapt this return value to our needs, if
necessary.
So reintroduce return of 0 for division by 0 as in the old
interpreter. Also in case of K which is guaranteed to be 32bit
wide, sk_chk_filter() already takes care of preventing division
by 0 invoked through K, so we can generally spare us these tests.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Reviewed-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recycling skb always had been very tough...
This time it appears GRO layer can accumulate skb->truesize
adjustments made by drivers when they attach a fragment to skb.
skb_gro_receive() can only subtract from skb->truesize the used part
of a fragment.
I spotted this problem seeing TcpExtPruneCalled and
TcpExtTCPRcvCollapsed that were unexpected with a recent kernel, where
TCP receive window should be sized properly to accept traffic coming
from a driver not overshooting skb->truesize.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup updates from Tejun Heo:
"A lot updates for cgroup:
- The biggest one is cgroup's conversion to kernfs. cgroup took
after the long abandoned vfs-entangled sysfs implementation and
made it even more convoluted over time. cgroup's internal objects
were fused with vfs objects which also brought in vfs locking and
object lifetime rules. Naturally, there are places where vfs rules
don't fit and nasty hacks, such as credential switching or lock
dance interleaving inode mutex and cgroup_mutex with object serial
number comparison thrown in to decide whether the operation is
actually necessary, needed to be employed.
After conversion to kernfs, internal object lifetime and locking
rules are mostly isolated from vfs interactions allowing shedding
of several nasty hacks and overall simplification. This will also
allow implmentation of operations which may affect multiple cgroups
which weren't possible before as it would have required nesting
i_mutexes.
- Various simplifications including dropping of module support,
easier cgroup name/path handling, simplified cgroup file type
handling and task_cg_lists optimization.
- Prepatory changes for the planned unified hierarchy, which is still
a patchset away from being actually operational. The dummy
hierarchy is updated to serve as the default unified hierarchy.
Controllers which aren't claimed by other hierarchies are
associated with it, which BTW was what the dummy hierarchy was for
anyway.
- Various fixes from Li and others. This pull request includes some
patches to add missing slab.h to various subsystems. This was
triggered xattr.h include removal from cgroup.h. cgroup.h
indirectly got included a lot of files which brought in xattr.h
which brought in slab.h.
There are several merge commits - one to pull in kernfs updates
necessary for converting cgroup (already in upstream through
driver-core), others for interfering changes in the fixes branch"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (74 commits)
cgroup: remove useless argument from cgroup_exit()
cgroup: fix spurious lockdep warning in cgroup_exit()
cgroup: Use RCU_INIT_POINTER(x, NULL) in cgroup.c
cgroup: break kernfs active_ref protection in cgroup directory operations
cgroup: fix cgroup_taskset walking order
cgroup: implement CFTYPE_ONLY_ON_DFL
cgroup: make cgrp_dfl_root mountable
cgroup: drop const from @buffer of cftype->write_string()
cgroup: rename cgroup_dummy_root and related names
cgroup: move ->subsys_mask from cgroupfs_root to cgroup
cgroup: treat cgroup_dummy_root as an equivalent hierarchy during rebinding
cgroup: remove NULL checks from [pr_cont_]cgroup_{name|path}()
cgroup: use cgroup_setup_root() to initialize cgroup_dummy_root
cgroup: reorganize cgroup bootstrapping
cgroup: relocate setting of CGRP_DEAD
cpuset: use rcu_read_lock() to protect task_cs()
cgroup_freezer: document freezer_fork() subtleties
cgroup: update cgroup_transfer_tasks() to either succeed or fail
cgroup: drop task_lock() protection around task->cgroups
cgroup: update how a newly forked task gets associated with css_set
...
Currently there is no way how to find out if a device supports busy
polling. So add a feature and make it dependent on ndo_busy_poll
existence.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
Pull core block layer updates from Jens Axboe:
"This is the pull request for the core block IO bits for the 3.15
kernel. It's a smaller round this time, it contains:
- Various little blk-mq fixes and additions from Christoph and
myself.
- Cleanup of the IPI usage from the block layer, and associated
helper code. From Frederic Weisbecker and Jan Kara.
- Duplicate code cleanup in bio-integrity from Gu Zheng. This will
give you a merge conflict, but that should be easy to resolve.
- blk-mq notify spinlock fix for RT from Mike Galbraith.
- A blktrace partial accounting bug fix from Roman Pen.
- Missing REQ_SYNC detection fix for blk-mq from Shaohua Li"
* 'for-3.15/core' of git://git.kernel.dk/linux-block: (25 commits)
blk-mq: add REQ_SYNC early
rt,blk,mq: Make blk_mq_cpu_notify_lock a raw spinlock
blk-mq: support partial I/O completions
blk-mq: merge blk_mq_insert_request and blk_mq_run_request
blk-mq: remove blk_mq_alloc_rq
blk-mq: don't dump CPU -> hw queue map on driver load
blk-mq: fix wrong usage of hctx->state vs hctx->flags
blk-mq: allow blk_mq_init_commands() to return failure
block: remove old blk_iopoll_enabled variable
blktrace: fix accounting of partially completed requests
smp: Rename __smp_call_function_single() to smp_call_function_single_async()
smp: Remove wait argument from __smp_call_function_single()
watchdog: Simplify a little the IPI call
smp: Move __smp_call_function_single() below its safe version
smp: Consolidate the various smp_call_function_single() declensions
smp: Teach __smp_call_function_single() to check for offline cpus
smp: Remove unused list_head from csd
smp: Iterate functions through llist_for_each_entry_safe()
block: Stop abusing rq->csd.list in blk-softirq
block: Remove useless IPI struct initialization
...
Replace the test in zap_completion_queue to test when it is safe to
free skbs in hard irq context with skb_irq_freeable ensuring we only
free skbs when it is safe, and removing the possibility of subtle
problems.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes a build error reported by Fengguang, that is
triggered when CONFIG_NETWORK_PHY_TIMESTAMPING is not set:
ERROR: "ptp_classify_raw" [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.ko] undefined!
The fix is to introduce its own file for the PTP BPF classifier,
so that PTP_1588_CLOCK and/or NETWORK_PHY_TIMESTAMPING can select
it independently from each other. IXP4xx driver on ARM needs to
select it as well since it does not seem to select PTP_1588_CLOCK
or similar that would pull it in automatically.
This also allows for hiding all of the internals of the BPF PTP
program inside that file, and only exporting relevant API bits
to drivers.
This patch also adds a kdoc documentation of ptp_classify_raw()
API to make it clear that it can return PTP_CLASS_* defines. Also,
the BPF program has been translated into bpf_asm code, so that it
can be more easily read and altered (extensively documented in [1]).
In the kernel tree under tools/net/ we have bpf_asm and bpf_dbg
tools, so the commented program can simply be translated via
`./bpf_asm -c prog` where prog is a file that contains the
commented code. This makes it easily readable/verifiable and when
there's a need to change something, jump offsets etc do not need
to be replaced manually which can be very error prone. Instead,
a newly translated version via bpf_asm can simply replace the old
code. I have checked opcode diffs before/after and it's the very
same filter.
[1] Documentation/networking/filter.txt
Fixes: 164d8c6665 ("net: ptp: do not reimplement PTP/BPF classifier")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jiri Benc <jbenc@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This minor patch fixes the following warning when doing
a `make htmldocs`:
DOCPROC Documentation/DocBook/networking.xml
Warning(.../net/core/filter.c:135): No description found for parameter 'insn'
Warning(.../net/core/filter.c:135): Excess function parameter 'fentry' description in '__sk_run_filter'
HTML Documentation/DocBook/networking.html
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main difference between napi_frags_skb() and napi_gro_receive() is that
the later is called while ethernet header was already pulled by the NIC
driver (eth_type_trans() was called before napi_gro_receive())
Jerry Chu in commit 299603e837 ("net-gro: Prepare GRO stack for the
upcoming tunneling support") tried to remove this difference by calling
eth_type_trans() from napi_frags_skb() instead of doing this later from
napi_frags_finish()
Goal was that napi_gro_complete() could call
ptype->callbacks.gro_complete(skb, 0) (offset of first network header =
0)
Also, xxx_gro_receive() handlers all use off = skb_gro_offset(skb) to
point to their own header, for the current skb and ones held in gro_list
Problem is this cleanup work defeated the frag0 optimization:
It turns out the consecutive pskb_may_pull() calls are too expensive.
This patch brings back the frag0 stuff in napi_frags_skb().
As all skb have their mac header in skb head, we no longer need
skb_gro_mac_header()
Reported-by: Michal Schmidt <mschmidt@redhat.com>
Fixes: 299603e837 ("net-gro: Prepare GRO stack for the upcoming tunneling support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to monitor carrier on/off transitions and detect link
flapping issues:
- new /sys/class/net/X/carrier_changes
- new rtnetlink IFLA_CARRIER_CHANGES (getlink)
Tested:
- grep . /sys/class/net/*/carrier_changes
+ ip link set dev X down/up
+ plug/unplug cable
- updated iproute2: prints IFLA_CARRIER_CHANGES
- iproute2 20121211-2 (debian): unchanged behavior
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces/reworks the kernel-internal BPF interpreter with
an optimized BPF instruction set format that is modelled closer to
mimic native instruction sets and is designed to be JITed with one to
one mapping. Thus, the new interpreter is noticeably faster than the
current implementation of sk_run_filter(); mainly for two reasons:
1. Fall-through jumps:
BPF jump instructions are forced to go either 'true' or 'false'
branch which causes branch-miss penalty. The new BPF jump
instructions have only one branch and fall-through otherwise,
which fits the CPU branch predictor logic better. `perf stat`
shows drastic difference for branch-misses between the old and
new code.
2. Jump-threaded implementation of interpreter vs switch
statement:
Instead of single table-jump at the top of 'switch' statement,
gcc will now generate multiple table-jump instructions, which
helps CPU branch predictor logic.
Note that the verification of filters is still being done through
sk_chk_filter() in classical BPF format, so filters from user- or
kernel space are verified in the same way as we do now, and same
restrictions/constraints hold as well.
We reuse current BPF JIT compilers in a way that this upgrade would
even be fine as is, but nevertheless allows for a successive upgrade
of BPF JIT compilers to the new format.
The internal instruction set migration is being done after the
probing for JIT compilation, so in case JIT compilers are able to
create a native opcode image, we're going to use that, and in all
other cases we're doing a follow-up migration of the BPF program's
instruction set, so that it can be transparently run in the new
interpreter.
In short, the *internal* format extends BPF in the following way (more
details can be taken from the appended documentation):
- Number of registers increase from 2 to 10
- Register width increases from 32-bit to 64-bit
- Conditional jt/jf targets replaced with jt/fall-through
- Adds signed > and >= insns
- 16 4-byte stack slots for register spill-fill replaced
with up to 512 bytes of multi-use stack space
- Introduction of bpf_call insn and register passing convention
for zero overhead calls from/to other kernel functions
- Adds arithmetic right shift and endianness conversion insns
- Adds atomic_add insn
- Old tax/txa insns are replaced with 'mov dst,src' insn
Performance of two BPF filters generated by libpcap resp. bpf_asm
was measured on x86_64, i386 and arm32 (other libpcap programs
have similar performance differences):
fprog #1 is taken from Documentation/networking/filter.txt:
tcpdump -i eth0 port 22 -dd
fprog #2 is taken from 'man tcpdump':
tcpdump -i eth0 'tcp port 22 and (((ip[2:2] - ((ip[0]&0xf)<<2)) -
((tcp[12]&0xf0)>>2)) != 0)' -dd
Raw performance data from BPF micro-benchmark: SK_RUN_FILTER on the
same SKB (cache-hit) or 10k SKBs (cache-miss); time in ns per call,
smaller is better:
--x86_64--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 90 101 192 202
new BPF 31 71 47 97
old BPF jit 12 34 17 44
new BPF jit TBD
--i386--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 107 136 227 252
new BPF 40 119 69 172
--arm32--
fprog #1 fprog #1 fprog #2 fprog #2
cache-hit cache-miss cache-hit cache-miss
old BPF 202 300 475 540
new BPF 180 270 330 470
old BPF jit 26 182 37 202
new BPF jit TBD
Thus, without changing any userland BPF filters, applications on
top of AF_PACKET (or other families) such as libpcap/tcpdump, cls_bpf
classifier, netfilter's xt_bpf, team driver's load-balancing mode,
and many more will have better interpreter filtering performance.
While we are replacing the internal BPF interpreter, we also need
to convert seccomp BPF in the same step to make use of the new
internal structure since it makes use of lower-level API details
without being further decoupled through higher-level calls like
sk_unattached_filter_{create,destroy}(), for example.
Just as for normal socket filtering, also seccomp BPF experiences
a time-to-verdict speedup:
05-sim-long_jumps.c of libseccomp was used as micro-benchmark:
seccomp_rule_add_exact(ctx,...
seccomp_rule_add_exact(ctx,...
rc = seccomp_load(ctx);
for (i = 0; i < 10000000; i++)
syscall(199, 100);
'short filter' has 2 rules
'large filter' has 200 rules
'short filter' performance is slightly better on x86_64/i386/arm32
'large filter' is much faster on x86_64 and i386 and shows no
difference on arm32
--x86_64-- short filter
old BPF: 2.7 sec
39.12% bench libc-2.15.so [.] syscall
8.10% bench [kernel.kallsyms] [k] sk_run_filter
6.31% bench [kernel.kallsyms] [k] system_call
5.59% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
4.37% bench [kernel.kallsyms] [k] trace_hardirqs_off_caller
3.70% bench [kernel.kallsyms] [k] __secure_computing
3.67% bench [kernel.kallsyms] [k] lock_is_held
3.03% bench [kernel.kallsyms] [k] seccomp_bpf_load
new BPF: 2.58 sec
42.05% bench libc-2.15.so [.] syscall
6.91% bench [kernel.kallsyms] [k] system_call
6.25% bench [kernel.kallsyms] [k] trace_hardirqs_on_caller
6.07% bench [kernel.kallsyms] [k] __secure_computing
5.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
--arm32-- short filter
old BPF: 4.0 sec
39.92% bench [kernel.kallsyms] [k] vector_swi
16.60% bench [kernel.kallsyms] [k] sk_run_filter
14.66% bench libc-2.17.so [.] syscall
5.42% bench [kernel.kallsyms] [k] seccomp_bpf_load
5.10% bench [kernel.kallsyms] [k] __secure_computing
new BPF: 3.7 sec
35.93% bench [kernel.kallsyms] [k] vector_swi
21.89% bench libc-2.17.so [.] syscall
13.45% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
6.25% bench [kernel.kallsyms] [k] __secure_computing
3.96% bench [kernel.kallsyms] [k] syscall_trace_exit
--x86_64-- large filter
old BPF: 8.6 seconds
73.38% bench [kernel.kallsyms] [k] sk_run_filter
10.70% bench libc-2.15.so [.] syscall
5.09% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.97% bench [kernel.kallsyms] [k] system_call
new BPF: 5.7 seconds
66.20% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
16.75% bench libc-2.15.so [.] syscall
3.31% bench [kernel.kallsyms] [k] system_call
2.88% bench [kernel.kallsyms] [k] __secure_computing
--i386-- large filter
old BPF: 5.4 sec
new BPF: 3.8 sec
--arm32-- large filter
old BPF: 13.5 sec
73.88% bench [kernel.kallsyms] [k] sk_run_filter
10.29% bench [kernel.kallsyms] [k] vector_swi
6.46% bench libc-2.17.so [.] syscall
2.94% bench [kernel.kallsyms] [k] seccomp_bpf_load
1.19% bench [kernel.kallsyms] [k] __secure_computing
0.87% bench [kernel.kallsyms] [k] sys_getuid
new BPF: 13.5 sec
76.08% bench [kernel.kallsyms] [k] sk_run_filter_int_seccomp
10.98% bench [kernel.kallsyms] [k] vector_swi
5.87% bench libc-2.17.so [.] syscall
1.77% bench [kernel.kallsyms] [k] __secure_computing
0.93% bench [kernel.kallsyms] [k] sys_getuid
BPF filters generated by seccomp are very branchy, so the new
internal BPF performance is better than the old one. Performance
gains will be even higher when BPF JIT is committed for the
new structure, which is planned in future work (as successive
JIT migrations).
BPF has also been stress-tested with trinity's BPF fuzzer.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Paul Moore <pmoore@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently pch_gbe, cpts, and ixp4xx_eth drivers that open-code
and reimplement a BPF classifier for the PTP protocol. Since all of them
effectively do the very same thing and load the very same PTP/BPF filter,
we can just consolidate that code by introducing ptp_classify_raw() in
the time-stamping core framework which can be used in drivers.
As drivers get initialized after bootstrapping the core networking
subsystem, they can make use of ptp_insns wrapped through
ptp_classify_raw(), which allows to simplify and remove PTP classifier
setup code in drivers.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch migrates an open-coded sk_run_filter() implementation with
proper use of the BPF API, that is, sk_unattached_filter_create(). This
migration is needed, as we will be internally transforming the filter
to a different representation, and therefore needs to be decoupled.
It is okay to do so as skb_timestamping_init() is called during
initialization of the network stack in core initcall via sock_init().
This would effectively also allow for PTP filters to be jit compiled if
bpf_jit_enable is set.
For better readability, there are also some newlines introduced, also
ptp_classify.h is only in kernel space.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch basically does two things, i) removes the extern keyword
from the include/linux/filter.h file to be more consistent with the
rest of Joe's changes, and ii) moves filter accounting into the filter
core framework.
Filter accounting mainly done through sk_filter_{un,}charge() take
care of the case when sockets are being cloned through sk_clone_lock()
so that removal of the filter on one socket won't result in eviction
as it's still referenced by the other.
These functions actually belong to net/core/filter.c and not
include/net/sock.h as we want to keep all that in a central place.
It's also not in fast-path so uninlining them is fine and even allows
us to get rd of sk_filter_release_rcu()'s EXPORT_SYMBOL and a forward
declaration.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to open up the possibility to internally transform a BPF program
into an alternative and possibly non-trivial reversible representation, we
need to keep the original BPF program around, so that it can be passed back
to user space w/o the need of a complex decoder.
The reason for that use case resides in commit a8fc927780 ("sk-filter:
Add ability to get socket filter program (v2)"), that is, the ability
to retrieve the currently attached BPF filter from a given socket used
mainly by the checkpoint-restore project, for example.
Therefore, we add two helpers sk_{store,release}_orig_filter for taking
care of that. In the sk_unattached_filter_create() case, there's no such
possibility/requirement to retrieve a loaded BPF program. Therefore, we
can spare us the work in that case.
This approach will simplify and slightly speed up both, sk_get_filter()
and sock_diag_put_filterinfo() handlers as we won't need to successively
decode filters anymore through sk_decode_filter(). As we still need
sk_decode_filter() later on, we're keeping it around.
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a jited flag into sk_filter struct in order to indicate
whether a filter is currently jited or not. The size of sk_filter is
not being expanded as the 32 bit 'len' member allows upper bits to be
reused since a filter can currently only grow as large as BPF_MAXINSNS.
Therefore, there's enough room also for other in future needed flags to
reuse 'len' field if necessary. The jited flag also allows for having
alternative interpreter functions running as currently, we can only
detect jit compiled filters by testing fp->bpf_func to not equal the
address of sk_run_filter().
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop taking the transmit lock when a network device has specified
NETIF_F_LLTX.
If no locks needed to trasnmit a packet this is the ideal scenario for
netpoll as all packets can be trasnmitted immediately.
Even if some locks are needed in ndo_start_xmit skipping any unnecessary
serialization is desirable for netpoll as it makes it more likely a
debugging packet may be trasnmitted immediately instead of being
deferred until later.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the assumption that the skbs that make it to
netpoll_send_skb_on_dev are allocated with find_skb, such that
skb->users == 1 and nothing is attached that would prevent the skbs from
being freed from hard irq context.
Remove this assumption by replacing __kfree_skb on error paths with
dev_kfree_skb_irq (in hard irq context) and kfree_skb (in process
context).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll_rx_enable and netpoll_rx_disable functions have always
controlled polling the network drivers transmit and receive queues.
Rename them to netpoll_poll_enable and netpoll_poll_disable to make
their functionality clear.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today netpoll_rx_enable and netpoll_rx_disable are called from
dev_close and and __dev_close, and not from dev_close_many.
Move the calls into __dev_close_many so that we have a single call
site to maintain, and so that dev_close_many gains this protection as
well. Which importantly makes batched network device deletes safe.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the code that needs to surround ndo_start_xmit
from netpoll_send_skb_on_dev into netpoll_start_xmit.
It is an unfortunate fact that as the netpoll code has been maintained
the primary call site ndo_start_xmit learned how to handle vlans
and timestamps but the second call of ndo_start_xmit in queue_process
did not.
With the introduction of netpoll_start_xmit this associated logic now
happens at both call sites of ndo_start_xmit and should make it easy
for that to continue into the future.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfp parameter was added in:
commit 47be03a28c
Author: Amerigo Wang <amwang@redhat.com>
Date: Fri Aug 10 01:24:37 2012 +0000
netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup()
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason for the gfp parameter was removed in:
commit c4cdef9b71
Author: dingtianhong <dingtianhong@huawei.com>
Date: Tue Jul 23 15:25:27 2013 +0800
bonding: don't call slave_xxx_netpoll under spinlocks
The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.
bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing else that calls __netpoll_setup or ndo_netpoll_setup
requires a gfp paramter, so remove the gfp parameter from both
of these functions making the code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb. However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers. That may not
always be the case. If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.
A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated. This way skb_mac_gso_segment
will correctly skip all mac headers.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dropping packets in __dev_queue_xmit() when transmit queue
is stopped (NIC TX ring buffer full or BQL limit reached) currently
outputs a syslog message.
It would be better to get a precise count of such events available in
netdevice stats so that monitoring tools can have a clue.
This extends the work done in caf586e5f2
("net: add a core netdev->rx_dropped counter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_zerocopy can copy elements of the frags array between skbs, but it doesn't
orphan them. Also, it doesn't handle errors, so this patch takes care of that
as well, and modify the callers accordingly. skb_tx_error() is also added to
the callers so they will signal the failed delivery towards the creator of the
skb.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces rcu_assign_pointer(x, NULL) with RCU_INIT_POINTER(x, NULL)
The rcu_assign_pointer() ensures that the initialization of a structure
is carried out before storing a pointer to that structure.
And in the case of the NULL pointer, there is no structure to initialize.
So, rcu_assign_pointer(p, NULL) can be safely converted to RCU_INIT_POINTER(p, NULL)
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet hash can be considered a property of the packet, not just
on RX path.
This patch changes name of rxhash and l4_rxhash skbuff fields to be
hash and l4_hash respectively. This includes changing uses of the
field in the code which don't call the access functions.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Neighbor Solicitation is ipv6 protocol, so we should check
skb->protocol with ETH_P_IPV6
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Cc: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ff661c38c ("net: rtnetlink notify events for FDB NTF_SELF adds and
deletes") reuses the function nlmsg_populate_fdb_fill() to notify fdb events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.
Libraries like libnl will wait forever for NLMSG_DONE.
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the code in net/core/flow.c by using this latter form of callback
registration.
Cc: Li RongQing <roy.qing.li@gmail.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cftype->write_string() just passes on the writeable buffer from kernfs
and there's no reason to add const restriction on the buffer. The
only thing const achieves is unnecessarily complicating parsing of the
buffer. Drop const from @buffer.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
The netpoll packet receive code only becomes active if the netpoll
rx_skb_hook is implemented, and there is not a single implementation
of the netpoll rx_skb_hook in the kernel.
All of the out of tree implementations I have found all call
netpoll_poll which was removed from the kernel in 2011, so this
change should not add any additional breakage.
There are problems with the netpoll packet receive code. __netpoll_rx
does not call dev_kfree_skb_irq or dev_kfree_skb_any in hard irq
context. netpoll_neigh_reply leaks every skb it receives. Reception
of packets does not work successfully on stacked devices (aka bonding,
team, bridge, and vlans).
Given that the netpoll packet receive code is buggy, there are no
out of tree users that will be merged soon, and the code has
not been used for in tree for a decade let's just remove it.
Reverting this commit can server as a starting point for anyone
who wants to resurrect netpoll packet reception support.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make rx_skb_hook, and rx in struct netpoll depend on
CONFIG_NETPOLL_TRAP Make rx_lock, rx_np, and neigh_tx in struct
netpoll_info depend on CONFIG_NETPOLL_TRAP
Make the functions netpoll_rx_on, netpoll_rx, and netpoll_receive_skb
no-ops when CONFIG_NETPOLL_TRAP is not set.
Only build netpoll_neigh_reply, checksum_udp service_neigh_queue,
pkt_is_ns, and __netpoll_rx when CONFIG_NETPOLL_TRAP is defined.
Add helper functions netpoll_trap_setup, netpoll_trap_setup_info,
netpoll_trap_cleanup, and netpoll_trap_cleanup_info that initialize
and cleanup the struct netpoll and struct netpoll_info receive
specific fields when CONFIG_NETPOLL_TRAP is enabled and do nothing
otherwise.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bond slave device neigh_tx handling into service_neigh_queue.
In connection with neigh_tx processing remove unnecessary tests of
a NULL netpoll_info. As the netpoll_poll_dev has already used
and thus verified the existince of the netpoll_info.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we no longer need to receive packets to safely drain the
network drivers receive queue move netpoll_trap and netpoll_set_trap
under CONFIG_NETPOLL_TRAP
Making netpoll_trap and netpoll_set_trap noop inline functions
when CONFIG_NETPOLL_TRAP is not set.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the strategy of netpoll from dropping all packets received
during netpoll_poll_dev to calling napi poll with a budget of 0
(to avoid processing drivers rx queue), and to ignore packets received
with netif_rx (those will safely be placed on the backlog queue).
All of the netpoll supporting drivers have been reviewed to ensure
either thay use netif_rx or that a budget of 0 is supported by their
napi poll routine and that a budget of 0 will not process the drivers
rx queues.
Not dropping packets makes NETPOLL_RX_DROP unnecesary so it is removed.
npinfo->rx_flags is removed as rx_flags with just the NETPOLL_RX_ENABLED
flag becomes just a redundant mirror of list_empty(&npinfo->rx_np).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper netpoll_rx_processing that reports when netpoll has
receive side processing to perform.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is already a warning for this case in the normal netpoll path,
but put a copy here in case how netpoll calls the poll functions
causes a differenet result.
netpoll will shortly call the napi poll routine with a budget 0 to
avoid any rx packets being processed. As nothing does that today
we may encounter drivers that have problems so a netpoll specific
warning seems desirable.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In poll_napi loop through all of the napi handlers even when the
budget falls to 0 to ensure that we process all of the tx_queues, and
so that we continue to call into drivers when our initial budget is 0.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
