Sample rates are only restricted by the capabilities of the
clock driver, so use SNDRV_PCM_RATE_CONTINUOUS instead of
SNDRV_PCM_RATE_8000_192000.
Tests (eg with pcm5122) have shown that bcm2835 works fine
in 384kHz/32bit stereo mode, so change the maximum allowed
rate from 192kHz to 384kHz.
Signed-off-by: Matthias Reichl <hias@horus.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
bcm2835 supports arbitrary positioning of channel data within
a frame and thus is capable of supporting TDM modes. Since
the driver is limited to 2-channel operations only TDM setups
with exactly 2 active slots are supported.
Logical TDM slot numbering follows the usual convention:
For I2S-like modes, with a 50% duty-cycle frame clock,
slots 0, 2, ... are transmitted in the first half of a frame,
slots 1, 3, ... are transmitted in the second half.
For DSP modes slot numbering is ascending: 0, 1, 2, 3, ...
Channel position calculation has been refactored to use
TDM info and moved out of hw_params.
set_tdm_slot, set_bclk_ratio and hw_params now check more
strictly if the configuration is valid. Illegal configurations
like odd number of slots in I2S mode, data lengths exceeding
slot width or frame sizes larger than the hardware limit of
1024 are rejected. Also hw_params now properly checks for
errors from clk_set_rate.
Allowed PCM formats are already guarded by stream constraints,
thus the formats check in hw_params has been removed and
data_length is now retrieved via params_width().
Also standard functions like snd_soc_params_to_bclk are now
being used instead of manual calculations to make the code
more readable.
Special care has been taken to ensure that set_bclk_ratio works
as before. The bclk ratio is mapped to a 2-channel TDM config
with a slot width of half the ratio. In order to support odd ratios,
which can't be expressed via a TDM config, the ratio (frame length)
is stored and used by hw_params.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make this const as it is only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add depends on HAS_DMA to Kconfig. This fixes error reported
by kbuild test robot when building for ARCH=m32r:
ERROR: "bad_dma_ops" [sound/soc/bcm/snd-soc-cygnus.ko] undefined!
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Cygnus audio DMA driver. It supports playback
and capture modes and uses ringbuffers for data transfer.
Signed-off-by: Lori Hikichi <lhikichi@broadcom.com>
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <arunp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Cygnus audio DAI driver. It supports I2S, TDM
and SPDIF modes and uses three clocks derived from PLL.
This patchset has been tested on Cygnus wireless audio
bcm958305K board.
Signed-off-by: Lori Hikichi <lhikichi@broadcom.com>
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <arunp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bcm2835-i2s driver already has support for the S16_LE format but
that format hasn't been made available because dmaengine_pcm didn't
support packed data transfers.
bcm2835-i2s needs 16-bit left+right channel data to be packed into
a 32-bit word, the FIFO register is 32-bit only and doesn't support
16-bit access.
Now that dmaengine_pcm supports packed transfers the format can
be made available by setting the SND_DMAENGINE_PCM_DAI_FLAG_PACK flag.
No further configuration is necessary:
- snd_dmaengine_dai_dma_data.addr_width is already set to
DMA_SLAVE_BUSWIDTH_4_BYTES to force 32-bit DMA transfers
- dmaengine_pcm will pick up the S16_LE format from the DAI
configuration and make it available since it's no longer
masked out due to the PACK flag.
- there are no further corner cases to catch in hw_params,
since the channel count is fixed at 2 we always have two
16-bit stereo samples that can be transferred via 32-bit DMA
Signed-off-by: Matthias Reichl <hias@horus.com>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only need to enable the clock if we are a clock master.
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
Original work by Zoltan Szenczi.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds 24 bit support to the I2S driver of the BCM2835
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the move to the new clock framework with commit 94cb7f76ca
("ARM: bcm2835: Switch to using the new clock driver support.")
this driver was no longer functional as it was manipulating the
clock registers locally without going true the framework.
This patch moves to use the new clock framework and also
moves away from the hardcoded address offsets for DMA getting
the dma-address directly from the device tree.
Note that the optimal bclk_ratio selection to avoid jitter
due to the use of fractional dividers, which is in the
current version has been removed, because not all devices
support these non power of 2 sized transfers, which resulted
in lots of (downstream) modules that use:
snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cleanup of includes so that they are ordered alphabetically.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CONFIG_SND_SOC_DMAENGINE_PCM was renamed to CONFIG_SND_DMAENGINE_PCM
recently. And yet we don't have to select it since
CONFIG_SND_GENERIC_DMAENGINE_PCM selects the dependency by itself, so
just rip it off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver adds support for digital audio (I2S)
for the BCM2835 SoC that is used by the
Raspberry Pi. External audio codecs can be
connected to the Raspberry Pi via P5 header.
It relies on cyclic DMA engine support for BCM2835.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
