This patch adds earlier initialization of spi_device.mode, as needed
on boards using nondefault chipselect polarity. An example would be
ones using the RS5C348 RTC without an external signal inverter between
the RTC chipselect and the SPI controller.
Without this mechanism, the first setup() call for that chip would
wrongly enable chips, corrupting transfers to/from other chips sharing
that SPI bus.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also sets the new fifo flag so that we don't hang on some errors with this
chipset.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move auto arrays to static (const). Clean up using PCI_DEVICE in places,
remove unreachable junk and dead code.
Fix the serverworks cable detect logic (if ordering is wrong). Backport
from libata. Plenty of scope for more cleanup left.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the controller FIFO cleared automatically on error we must not try
and drain it as this will hang some chips.
Based in concept on a broken patch from -mm some while back
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kill a pair of long escaped debug printk calls
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove all the ifdef preparation for enhanced features that never occcurred
and is only in libata. For the SATA chips (but not yet PATA ones) politely
suggest to the user that libata may offer more features.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylylov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is based on the proposed patches flying around but also checks that
the device in question is new enough to have word 93 rather thanb blindly
assuming word 93 == 0 means SATA (see ATA-5, ATA-7)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a erroneous calculation of the legacy brightness values as reported by
Paul Collins. Additionally, it moves the calculation of the negative value
in the radeonfb driver after the value check.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Collins <paul@briny.ondioline.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify the watchdog timeout in IPMI to only do things at panic/reboot time if
the watchdog timer was already running. Some BIOSes do not disable the
watchdog timer at startup, and this led to a reboot a while later if the new
OS running didn't start monitoring the watchdog, even if the watchdog was not
running before.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was some old high-res-timer code in the IPMI driver that is dead.
Remove it.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tidy up the timer usage in the IPMI driver.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Turned out to be rather a monster
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Works better on SMP if...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove 'active' field from tty buffer structure. This was added in 2.6.16
as part of a patch to make the new tty buffering SMP safe. This field is
unnecessary with the more intelligently written flush_to_ldisc that adds
receive_room handling.
Removing this field reverts to simpler logic where the tail buffer is
always the 'active' buffer, which should not be freed by flush_to_ldisc.
(active == buffer being filled with new data)
The result is simpler, smaller, and faster tty buffer code.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Flush data serially to line discipline in blocks no larger than
tty->receive_room to avoid losing data if line discipline is busy (such as
N_TTY operating at high speed on heavily loaded system) or does not accept
data in large blocks (such as N_MOUSE).
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove TTY_DONT_FLIP tty flag. This flag was introduced in 2.1.X kernels
to prevent the N_TTY line discipline functions read_chan() and
n_tty_receive_buf() from running at the same time. 2.2.15 introduced
tty->read_lock to protect access to the N_TTY read buffer, which is the
only state requiring protection between these two functions.
The current TTY_DONT_FLIP implementation is broken for SMP, and is not
universally honored by drivers that send data directly to the line
discipline receive_buf function.
Because TTY_DONT_FLIP is not necessary, is broken in implementation, and is
not universally honored, it is removed.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Same as with already do with the file operations: keep them in .rodata and
prevents people from doing runtime patching.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[netdrvr] Remove long-unused bits from Becker template drivers
[netdrvr] natsemi: minor cleanups
[netdrvr] natsemi: Separate out media initialization code
[PATCH] WAN: update info page for a bunch of my drivers
[PATCH] drivers/net/hamradio/dmascc.c: fix section mismatch
[PATCH] Fix phy id for LXT971A/LXT972A
[PATCH] DM9000 - minor code cleanups
[PATCH] DM9000 - do no re-init spin lock
[PATCH] DM9000 - check for MAC left in by bootloader
[PATCH] DM9000 - better checks for platform resources
This patch removes the old pmac ide led blink code and
adds generic LED subsystem support for the LED.
It maintains backward compatibility with the old
BLK_DEV_IDE_PMAC_BLINK Kconfig option which now
simply selects the new code and influences the
default trigger.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 02dd7ae289 ("[PATCH] i2c-i801:
Merge setup function") has a missing return 0 in the _probe() function.
This means the error path is always executed and pci_disable_device() is
called even when the device just got successfully enabled.
Having the SMBus device disabled makes some systems (eg.
Fujitsu-Siemens Lifebook E8010) hang hard during power-off.
Intead of reverting the whole commit this patch fixes it up:
- don't ever call pci_disable_device(), also not in the _remove() function
to avoid hangs
- fix missing pci_release_region() in error path
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Collection of fixes for the ColdFire FEC ethernet driver:
. reworked event setting so that it occurs after the MII setup.
roucaries bastien <roucaries.bastien@gmail.com>
. Do not read cbd_sc in memory for each bit we test. Once per buffer is enough.
. Overrun errors must increase `rx_fifo_errors', not `rx_crc_errors'
. No need for a special value to activate rx or tx. Only write access matters.
. Simplify parameter of eth_copy_and_sum : `data' has already the right value.
. Some spelling fixes.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set different irq priority levels for each IRQ requested.
According to the Freescale ColdFire documentation each separate IRQ
must have its own unique priority/level combination.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the FEC module in the ColdFire 532x CPU family.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid requesting a `Graceful Transmit Stop' when link has disappeared,
because that request cannot complete without link.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (26 commits)
V4L/DVB (4263): Fix warning when compiling on 64 bit machines
V4L/DVB (4261): Included required header for in-kernel compilation
V4L/DVB (4260): Stradis.c: make 2 functions static
V4L/DVB (4259): Pass an explicit log prefix to cx2341x_log_status
V4L/DVB (4257): Fix 64-bit compile warnings.
V4L/DVB (4255): Tda9887 default TOP value is 0x10
V4L/DVB (4254): Remove obsoleted tuner_debug option.
V4L/DVB (4253): IVTV VBI format description too long.
V4L/DVB (4252): Remove duplicate 'tda9887' in info messages.
V4L/DVB (4245): Reduce the amount of pvrusb2-sourced noise going into the system log
V4L/DVB (4244): Implement use of cx2341x module in pvrusb2 driver
V4L/DVB (4243): Exploit new V4L control features in pvrusb2
V4L/DVB (4242): Don't suspend encoder when changing its attributes (in pvrusb2)
V4L/DVB (4241): Fix faulty encoder error recovery in pvrusb2
V4L/DVB (4240): Various V4L control enhancements in pvrusb2
V4L/DVB (4239): Handle boolean controls in pvrusb2
V4L/DVB (4238): Make sure flags field is initialized when quering a control in pvrusb2
V4L/DVB (4237): Move LOG_STATUS bracketing to a different part of the pvrusb2 driver
V4L/DVB (4236): Rearrange things in pvrusb2 driver in preparation for using cx2341x module
V4L/DVB (4235): Increase the maximum number of controls that pvrusb2-sysfs.c can handle.
...
DLE masking was non-functional since the new tty handling.
Found by Peter Evertz <leo2@pec.homeip.net>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's available in a header as a static inline - there's no need to export it.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sysfs entries 'sched_mc_power_savings' and 'sched_smt_power_savings' in
/sys/devices/system/cpu/ control the MC/SMT power savings policy for the
scheduler.
Based on the values (1-enable, 0-disable) for these controls, sched groups
cpu power will be determined for different domains. When power savings
policy is enabled and under light load conditions, scheduler will minimize
the physical packages/cpu cores carrying the load and thus conserving
power(with a perf impact based on the workload characteristics... see OLS
2005 CMP kernel scheduler paper for more details..)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Con Kolivas <kernel@kolivas.org>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace the temp makefile hacks with proper CONFIG entries, which are also
added to Kconfig.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add current pin settings to gpio_dump() output. This adds the last 'word' to
the syslog lines, which displays the input and output values that the pin is
set to.
pc8736x_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE io:1/1
The 2 values may differ for a number of reasons:
1- the pin output circuitry is diaabled, (as the above 'TS' indicates)
2- it needs a pullup resistor to drive the attached circuit,
3- the external circuit needs a pullup so the open-drain has something
to pull-down
4- the pin is wired to Vcc or Ground
It might be appropriate to add a WARN for 2,3,4, since they could
damage the chip and/or circuit, esp if misconfig goes unnoticed.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hmm. Im somewhat ambivalent about this patch, since with it, driver wont
build for vanilla 17 or older.
Its also only 1/2 of your suggestion - when I tried it, I was building against
vanilla 17, and asm/uaccess.h cause compilation failure. Looking back, Im
perplexed as to why linux/io.h didnt cause same failure ?!?
use linux/io.h rather than asm/io.h
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace spinlocks guarding gpio config ops with mutexes. This is a me-too
patch, and is justifiable insofar as mutexes have stricter semantics and
better debugging support, so are preferred where they are applicable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a working gpio_current() to pc8736x_gpio.c (the previous implementation
just threw a dev_warn), and fix gpio_change() to use gpio_current() rather
than the incorrect (and temporary) gpio_get(). Initialize shadow-regs so this
all works.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use of dev_dbg() and friends is considered good practice. dev_dbg() needs a
struct device *devp, but nsc_gpio is only a helper module, so it doesnt
have/need its own. To provide devp to the user-modules (scx200 & pc8736x
_gpio), we add it to the vtable, and set it during init.
Also squeeze nsc_gpio_dump()'s format a little.
[ 199.259879] pc8736x_gpio.0: io09: 0x0044 TS OD PUE EDGE LO DEBOUNCE
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds platform-device to (just introduced) driver, and uses it to replace many
printks with dev_dbg() etc. This could trivially be merged into previous
patch, but this way matches better with the corresponding patch that does the
same change to scx200_gpio.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the brand new pc8736x_gpio driver. This is mostly based upon
scx200_gpio.c, but the platform_dev is treated separately, since its fairly
big too.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the meaning of config-bits is the same for scx200 and pc8736x _gpios, we
can share a function to deliver this to user. Since it is called via the
vtable, its also completely replaceable. For now, we keep using printk...
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that the read(), write() file-ops are dispatching gpio-ops via the vtable,
they are generic, and can be moved 'verbatim' to the nsc_gpio common-support
module. After the move, various symbols are renamed to update 'scx200_' to
'nsc_', and headers are adjusted accordingly.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the nsc_gpio common-support module as an empty shell. Next patch starts
the migration of the common gpio support routines.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now actually call the gpio operations thru the vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Abstract the gpio operations into a new nsc_gpio_ops vtable.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new driver command: 'v' which calls gpio_dump() on the pin. The output
goes to the log, like all other INFO messages in the original driver. Giving
the user control over the feedback they 'need' is construed to be a
user-friendly feature, and allows us (later) to dial down many INFO messages
to DEBUG log-level.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a platform-device to scx200_gpio, and use its struct device dev member
(ie: devp) in dev_dbg() once.
There are 2 alternatives here (Im soliciting guidance/commentary):
- use isa_device, if/when its added to the kernel.
- alter scx200.c to EXPORT_GPL its private devp so that both scx200_gpio,
and the (to be added) nsc_gpio module can use it. Since the available devp
is in 'grandparent', this seems like too much 'action at a distance'.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adopt many modern 2.6 coding practices, ala LDD3, chapter 3. Changes are
limited to initialization calls from module init, ie: cdev_init, cdev_add,
*_chrdev_region, mkdev.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GPIO SUPPORT FOR SCx200 & PC8736x
The patch-set reworks the 2.4 vintage scx200_gpio driver for modern 2.6, and
refactors GPIO support to reuse it in a new driver for the GPIO on PC-8736x
chips. Its handy for the Soekris.com net-4801, which has both chips.
These patches have been seen recently on Kernel-Mentors, and then
Kernel-Newbies ML, where Jesper Juhl kindly reviewed it. His feedback has
been incorporated. Thanks Jesper !
Its also gone to soekris-tech@soekris.com for possible testing by linux folks,
I've gotten 1 promise so far. Theyre mostly BSD folk over there, but we'll
see..
Device-file & Sysfs
The driver preserves the existing device-file interface, including the
write/cmd set, but adds v to 'view' the pin-settings & configs by inducing,
via gpio_dump(), a dev_info() call. Its a fairly crappy way to get status,
but it sticks to the syslog approach, conservatively.
Allowing users to voluntarily trigger logging is good, it gives them a
familiar way to confirm their app's control & use of the pins, and I've thus
reduced the pin-mode-updates from dev_info to dev_dbg.
I've recently bolted on a proto sysfs interface for both new drivers. Im not
including those patches here; they (the patch + doc-pre-patch) are still quite
raw (and unreviewed on KNML), and since they 'invent' a convention for GPIO, a
proper vetting is needed. Since this patchset is much bigger than my previous
ones, Id like to keep things simpler, and address it 1st, before bolting on
more stuff.
The driver-split
The Geode CPU and the PC-87366 Super-IO chip have GPIO units which share a
common pin-architecture (same pin features, with same bits controlling), but
with different addressing mechanics and port organizations.
The vintage driver expresses the pin capabilities with pin-mode commands
[OoPpTt],etc that change the pin configurations, and since the 2 chips share
pin-arch, we can reuse the read(), write() commands, once the implementation
is suitably adjusted.
The patchset adds a vtable: struct nsc_gpio_ops, to abstract the existing gpio
operations, then adjusts fileops.write() code to invoke operations via that
vtable. Driver specific open()s set private_data to the vtable so its
available for use by write().
The vtable gets the gpio_dump() too, since its user-friendly, and (could be
construed as) part of the current device-file interface. To support use of
dev_dbg() in write() & _dump(), the vtable gets a dev ptr too, set by both
scx200 & pc8736x _gpio drivers.
heres how the pins are presented in syslog:
[ 1890.176223] scx200_gpio.0: io00: 0x0044 TS OD PUE EDGE LO DEBOUNCE
[ 1890.287223] scx200_gpio.0: io01: 0x0003 OE PP PUD EDGE LO
nsc_gpio.c: new file is new home of several file-ops methods, which are
modified to get their vtable from filp->private_data, and use it where needed.
scx200_gpio.c: keeps some of its existing gpio routines, but now wires them up
via the vtable (they're invoked by nsc_gpio.c:nsc_gpio_write() thru this
vtable). A driver-spcific open() initializes filp->private_data with the
vtable.
Once the split is clean, and the scx200_gpio driver is working, we copy and
modify the function and variable names, and rework the access-method bodies
for the different addressing scheme.
Heres a working overview of the patchset:
# series file for GPIO
# Spring Cleaning
gpio-scx/patch.preclean # scripts/Lindent fixes, editor-ctrl comments
# API Modernization
gpio-scx/patch.api26 # what I learned from LDD3
gpio-scx/patch.platform-dev-2 # get pdev, support for dev_dbg()
gpio-scx/patch.unsigned-minor # fix to match std practice
# Debuggability
gpio-scx/patch.dump-diet # shrink gpio_dump()
gpio-scx/patch.viewpins # add new 'command' to call dump()
gpio-scx/patch.init-refactor # pull shadow-register init to sub
# Access-Abstraction (add vtable)
gpio-scx/patch.access-vtable # introduce nsg_gpio_ops vtable, w dump
gpio-scx/patch.vtable-calls # add & use the vtable in scx200_gpio
gpio-scx/patch.nscgpio-shell # add empty driver for common-fops
# move code under abstraction
gpio-scx/patch.migrate-fops # move file-ops methods from scx200_gpio
gpio-scx/patch.common-dump # mv scx200.c:scx200_gpio_dump() to nsc_gpio.c
gpio-scx/patch.add-pc8736x-gpio # add new driver, like old, w chip adapt
# gpio-scx/patch.add-DEBUG # enable all dev_dbg()s
# Cleanups
# finish printk -> dev_dbg() etc
gpio-scx/patch.pdev-pc8736x # new drvr needs pdev too,
gpio-scx/patch.devdbg-nscgpio # add device to 'vtable', use in dev_dbg()
# gpio-scx/patch.pin-config-view # another 'c' 'command'
# gpio-scx/quiet-getset # take out excess dbg stuff (pretty quiet
now)
gpio-scx/patch.shadow-current # imitate scx200_gpio's shadow regs in
pc87*
# post KMentors-post patches ..
gpio-scx/patch.mutexes # use mutexes for config-locks
gpio-scx/patch.viewpins-values # extend dump to obsolete separate 'c' cmd
gpio-scx/patch.kconfig # add stuff for kbuild
# TBC
# combine api26 with pdev, which is just one step.
# merge c&v commands to single do-all-fn
# delay viewpins, dump-diet should also un-ifdef it too.
diff.sys-gpio-rollup-1
This patch:
Removed editor format-control comments, and used scripts/Lindent to clean up
whitespace, then deleted the bogus chunks :-(
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_blocks associated with cpu_notifier as __cpuinitdata.
__cpuinitdata makes sure that the data is init time only unless
CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CPUs come online only at init time (unless CONFIG_HOTPLUG_CPU is defined).
So, cpu_notifier functionality need to be available only at init time.
This patch makes register_cpu_notifier() available only at init time, unless
CONFIG_HOTPLUG_CPU is defined.
This patch exports register_cpu_notifier() and unregister_cpu_notifier() only
if CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.17, there was a problem with cpu_notifiers and XFS. I provided a
band-aid solution to solve that problem. In the process, i undid all the
changes you both were making to ensure that these notifiers were available
only at init time (unless CONFIG_HOTPLUG_CPU is defined).
We deferred the real fix to 2.6.18. Here is a set of patches that fixes the
XFS problem cleanly and makes the cpu notifiers available only at init time
(unless CONFIG_HOTPLUG_CPU is defined).
If CONFIG_HOTPLUG_CPU is defined then cpu notifiers are available at run
time.
This patch reverts the notifier_call changes made in 2.6.17
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to serialize access to the global rtc_idr even in this error path.
Signed-off-by: Sonny Rao <sonny@burdell.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are two locking sets involved. One locks the board mappings and the
other is the tty open/close locking. The low level code was clearly
designed to be ported to OS's with spin locks already so pretty much comes
out in the wash
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Corey Minyard <minyard@acm.org>
The kthread used to speed up polling for IPMI was using udelay in its
busy-wait polling loop when the lower-level state machine told it to do a
short delay. This just used CPU and didn't help scheduling, thus causing
bad problems with other tasks. Call schedule() instead.
Signed-off-by: Corey Minyard <minyard@acm.org>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix TCSBRK comment to prevent confusion or accidental removal.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update two drivers to use poison.h.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Localize poison values into one header file for better documentation and
easier/quicker debugging and so that the same values won't be used for
multiple purposes.
Use these constants in core arch., mm, driver, and fs code.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Matt Mackall <mpm@selenic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Goto-san's patch, we can add new pgdat/node at runtime. I'm now
considering node-hot-add with cpu + memory on ACPI.
I found acpi container, which describes node, could evaluate cpu before
memory. This means cpu-hot-add occurs before memory hot add.
In most part, cpu-hot-add doesn't depend on node hot add. But register_cpu(),
which creates symbolic link from node to cpu, requires that node should be
onlined before register_cpu(). When a node is onlined, its pgdat should be
there.
This patch-set holds off creating symbolic link from node to cpu
until node is onlined.
This removes node arguments from register_cpu().
Now, register_cpu() requires 'struct node' as its argument. But the array of
struct node is now unified in driver/base/node.c now (By Goto's node hotplug
patch). We can get struct node in generic way. So, this argument is not
necessary now.
This patch also guarantees add cpu under node only when node is onlined. It
is necessary for node-hot-add vs. cpu-hot-add patch following this.
Moreover, register_cpu calculates cpu->node_id by cpu_to_node() without regard
to its 'struct node *root' argument. This patch removes it.
Also modify callers of register_cpu()/unregister_cpu, whose args are changed
by register-cpu-remove-node-struct patch.
[Brice.Goglin@ens-lyon.org: fix it]
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When new node becomes enable by hot-add, new sysfs file must be created for
new node. So, if new node is enabled by add_memory(), register_one_node() is
called to create it. In addition, I386's arch_register_node() and a part of
register_nodes() of powerpc are consolidated to register_one_node() as a
generic_code().
This is tested by Tiger4(IPF) with node hot-plug emulation.
Signed-off-by: Keiichiro Tokunaga <tokuanga.keiich@jp.fujitsu.com>
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is to find node id from acpi's handle of memory_device in DSDT. _PXM for
the new node can be found by acpi_get_pxm() by using new memory's handle. So,
node id can be found by pxm_to_nid_map[].
This patch becomes simpler than v2 of node hot-add patch.
Because old add_memory() function doesn't have node id parameter.
So, kernel must find its handle by physical address via DSDT again.
But, v3 just give node id to add_memory() now.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change the name of old add_memory() to arch_add_memory. And use node id to
get pgdat for the node at NODE_DATA().
Note: Powerpc's old add_memory() is defined as __devinit. However,
add_memory() is usually called only after bootup.
I suppose it may be redundant. But, I'm not well known about powerpc.
So, I keep it. (But, __meminit is better at least.)
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When acpi_memory_device_init() is called at boottime to register struct
memory acpi_memory_device, acpi_bus_add() are called via
acpi_driver_attach().
But it also calls ops->start() function. It is called even if the memory
blocks are initialized at early boottime. In this case add_memory() return
-EEXIST, and the memory blocks becomes INVALID state even if it is normal.
This is patch to avoid calling add_memory() for already available memory.
[akpm@osdl.org: coding cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a patch to call add_memroy() when notify reaches for new node's add
event.
When new node is added, notify of ACPI reaches container device which means
the node.
Container device driver calls acpi_bus_scan() to find and add belonging
devices (which means cpu, memory and so on). Its function calls add and
start function of belonging devices's driver.
Howevever, current memory hotplug driver just register add function to
create sysfs file for its memory. But, acpi_memory_enable_device() is not
called because it is considered just the case that notify reaches memory
device directly. So, if notify reaches container device nothing can call
add_memory().
This is a patch to create start function which calls add_memory().
add_memory() can be called by this when notify reaches container device.
[akpm@osdl.org: coding cleanups]
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current acpi memory hotplug just looks into the first entry of resources in
_CRS. But, _CRS can contain plural resources. So, if _CRS contains plural
resoureces, acpi memory hot add cannot add all memory.
With this patch, acpi memory hotplug can deal with Memory Device, whose
_CRS contains plural resources.
Tested on ia64 memory hotplug test envrionment (not emulation, uses alpha
version firmware which supports dynamic reconfiguration of NUMA.)
Note: Microsoft's Windows Server 2003 requires big (>4G)resoureces to be
divided into small (<4G) resources. looks crazy, but not invalid.
(See http://www.microsoft.com/whdc/system/pnppwr/hotadd/hotaddmem.mspx)
For this reason, a firmware vendor who supports Windows writes plural
resources in a _CRS even if they are contiguous.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a helper to asm/pdc.h to translate OS_ID values to strings
and use it in the pdc_stable driver.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
We were assigned an OS_ID of 0x0006. Consistently use OS_ID_LINUX
instead of using the magic number. Also update the OS_ID_ defines in
asm/pdc.h to reflect this.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
pdc_stable v0.30:
This patch introduces 3 more files to the /sys/firmware/stable tree:
- diagnostic, which contains a cryptic hex string
- osdep1, a 16 bytes os-dependent storage area always available
- osdep2, another os-dependent storage area which existence/size depends
on hversion.
This patch also adds code to setup the "Linux" signature in stable
storage. That is to say that starting with this patch, the kernel will
now sign its OSID (0x0006, thx LaMont) in Stable Storage upon boot,
whether pdc_stable is enabled or not.
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch removes a limitation of the original code, so that CHASSIS
codes can be sent to all machines. On machines with a LCD panel, this
code displays "INI" during bootup, "RUN" when the system is booted and
running, "FLT" when a panic occurs, etc.
This part of the code can be enabled/disabled through CONFIG_PDC_CHASSIS
This patch also adds minimalistic support for Chassis warnings, through
a proc entry '/proc/chassis', which will reflect the warnings status (PSU
or fans failure when they happen, NVRAM battery level and temperature
thresholds overflows).
This part of the code can be enabled/disabled through CONFIG_PDC_CHASSIS_WARN
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Some debugging code in sba_iommu.c should be testing ioc_needs_fdc,
not directly testing boot_cpu_data.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Clean up gcc 4.1 warnings noted by Joel Soete.
Kyle McMartin gets kudos for pointing out the issues.
Matthew Wilcox noticed sba_iommu was using open coded versions
of (read|write)X.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The other way round works not really well with boards which have a
static NAND chipselect.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Allow lseek(mtdchar_fd, 0, SEEK_END) to succeed, which currently fails
with EINVAL.
lseek(fd, 0, SEEK_END) should result into the same fileposition as
lseek(fd, 0, SEEK_SET) + read(fd, buf, length(fd))
Furthermore, lseek(fd, 0, SEEK_CUR) should return the current file position,
which in case of an encountered EOF should not result in EINVAL
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I was unable to compile ts7250.c after your refactor commit,
it's a typo probably.
-- ynezz
From: Petr Stetiar <ynezz@true.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It should be done before calling class_device_unregister() because
it will destroy the device and free memory if there are no other
references to the device.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on an original patch from Ralf Baechle <ralf@linux-mips.org> and
Vivek Goyal <vgoyal@in.ibm.com>. This is needed in order to prepare for
changing the size of resources.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a simple off-by-one error in the mtd physmap driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
