Before we have a probe response frame (which is used as the
beacon too) there's no need to ask drivers to beacon, they
will not get a beacon anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a directed tim bit is set, mac80211 currently disables power save
ands sends a null frame to the AP. But if dynamic power save is
disabled, mac80211 will not enable power save ever gain. Fix this by
adding ps-poll functionality to mac80211. When a directed tim bit is
set, mac80211 sends a ps-poll frame to the AP and checks for the more
data bit in the returned data frames.
Using ps-poll is slower than waking up with null frame, but it's saves more
power in cases where the traffic is low. Userspace can control if either
ps-poll or null wakeup method is used by enabling and disabling dynamic
power save.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 checks for the multicast tim bit from beacons,
disables power save and sends a null frame if the bit is set. This was
added to support ath9k. But this is a bit controversial because the AP will
send multicast frames immediately after the beacon and the time constraints
are really high. Relying mac80211 to be fast enough here might not be
reliable in all situations. And there's no need to send a null frame, AP
will send the frames immediately after the dtim beacon no matter what.
Also if dynamic power save is disabled (iwconfig wlan0 power timeout 0)
currently mac80211 disables power save whenever the multicast bit is set
but it's never enabled again after receiving the first multicast/broadcast
frame.
The current implementation is not usable on p54/stlc45xx and the
easiest way to fix this is to remove the multicast tim bit check
altogether. Handling multicast tim bit in host is rare, most of the
designs do this in firmware/hardware, so it's better not to have it in
mac80211. It's a lot better to do this in firmware/hardware, or if
that's not possible it could be done in the driver.
Also renamed the function to ieee80211_check_tim() to follow the style
of the file.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue happens only when we are associated with a 11n AP and power save
is enabled. In the function 'ieee80211_master_start_xmit', ps_disable_work
is queued where wake_queues is called. But before this work is executed,
we check if the queues are stopped in _ieee80211_tx and return TX_AGAIN to
ieee8011_tx which leads to the warning message.
This patch fixes this erroneous case.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We try to find the correct outgoing interface for injected frames
based on the TA, but since this is a hack for hostapd 11w, restrict
the heuristic to AP mode interfaces. At some point we'll add the
ability to give an interface index in radiotap or so and just
remove this heuristic again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.28.x]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no point having the bss information of currently associated AP
when the AP is detected to be out of range.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Monitor mode is able to TX by using injected frames. We should
not allow injected frames to be sent unless allowed by regulatory
rules. Since AP mode uses a monitor interfaces to transmit
management frames we have to take care to not break AP mode as
well while resolving this. We can deal with this by allowing compliant
APs solutions to inform mac80211 if their monitor interface is
intended to be used for an AP by setting a cfg80211 flag for the
monitor interface. hostapd, for example, currently does its own
checks to ensure AP mode is not used on channels which require radar
detection. Once such solutions are available it can can add this
flag for monitor interfaces.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also call our own ieee80211_master_setup routine instead of
overwriting almost all the values from ether_setup; this
loses a few assignments that are pointless on the master
interface anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert to new net_device_ops in 2.6.28 and later.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Giving the signal in dB isn't much more useful to userspace
than giving the signal in unspecified units. This removes
some radiotap information for zd1211 (the only driver using
this flag), but it helps a lot for getting cfg80211-based
scanning which won't support dB, and zd1211 being dB is a
little fishy anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I hold back this patch for around a week to avoid
confusion. This is the second step of
"mac80211: Fixed BSSID handling revisited".
With it, in the situation of a strange merge to the
same BSSID (e.g. caused by a TSF overflow) only
reset_tsf() is called.
And sta_info_flush_delayed() is only called if you
change the network manually, not on an automatic
BSSID merge.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a bug when creating a new IBSS network with a
fixed BSSID. The fixed BSSID situation is now with one of
my last patches handled in ieee80211_sta_find_ibss()
function.
It's more robust to test against
(ifsta->flags & IEEE80211_STA_PREV_BSSID_SET), because
ifsta->state is not seted right in every situation and so
the creating of the new IBSS network sometimes hangs after
the first try to scan for a network to merge.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to associate with a non-existent SSID stops the
state machine after the first run. Subsequent association
requests fail to start the scan engine. Fix this by resetting
assoc_scan_tries to zero after completing a scan run.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the dynamic power save timer has been started before the power save
is disabled using iwconfig, we fail to cancel the timer. Hence cancel it
while disabling power save.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables low-level driver independent debugging of the TSF and remove the driver specific things of ath5k and ath9k from the debugfs.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using only the RTNL has a number of problems, most notably that
ieee80211_iterate_active_interfaces() and other interface list
traversals cannot be done from the internal workqueue because it
needs to be flushed under the RTNL.
This patch introduces a new mutex that protects the interface list
against modifications. A more detailed explanation is part of the
code change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers can theoretically queue more work in one of their callbacks
from mac80211 suspend, so let's flush it once more to be on the safe
side, just before calling ->stop().
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: make workqueue freezable" made the mac80211
workqueue freezeable to prevent us from doing any work after the
driver went away. This was fine before mac80211 had any suspend
support.
However, now we want to flush this workqueue in suspend(). Because
the thread for a freezeable workqueue is stopped before the device
class suspend() is called, flush_workqueue() will hang in the
suspend-to-disk case.
Converting it back to a non-freezeable queue will keep suspend from
hanging. Moreover, since we flush the workqueue under RTNL and
userspace is stopped, there won't be any new work in the workqueue
until after resume. Thus we still don't have to worry about pinging
the AP without hardware.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleanup the fixed BSSID handling, that
ieee80211_sta_set_bssid() works like ieee80211_sta_set_ssid(). So
that the BSSID is only a second selection criterion besides the
SSID. This allows us to create new IBSS networks with fixed BSSIDs,
which was broken before.
In the second version of this patch the handling of the stupid merges
to the same BSSID is moved out to get reworked into an other patch.
And this version hopefully solves the problems with some low-level
drivers and re-adds the config BSSID warning to help debugging the
low-level drivers.
Much thanks to all who have helped testing! :)
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds an low-level driver independent entry to read the TSF value into the debugfs of mac80211. This makes debugging the IBSS handling of wifi drivers easier.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a driver is given a wiphy and it wants to get to its private
mac80211 driver area it can use wiphy_to_ieee80211_hw() to get first
to its ieee80211_hw and then access the private structure via hw->priv. The
wiphy_priv() is already being used internally by mac80211 and drivers
should not use this. This can be helpful in a drivers reg_notifier().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a flag to notify drivers to start and stop
beaconing when needed, for example, during a scan run. Based
on Sujith's first patch to do the same, but now disables
beaconing for all virtual interfaces while scanning, has a
separate change flag and tracks user-space requests.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the standards only define 12 legacy rates, 32 is certainly
a sane upper limit and we don't need to use u64 everywhere. Add
sanity checking that no more than 32 rates are registered and
change the variables to u32 throughout.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Then one place can be a static const.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The separate Association Comeback Time IE was removed from IEEE 802.11w
and the Timeout Interval IE (from IEEE 802.11r) is used instead. The
editing on this is still somewhat incomplete in IEEE 802.11w/D7.0, but
still, the use of Timeout Interval IE is the expected mechanism.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces suspend and resume callbacks to mac80211,
allowing mac80211 to quiesce its state (bringing down interfaces,
removing keys, etc) in preparation for suspend. cfg80211 will call
the suspend hook before the device suspend, and resume hook after
the device resume.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ADDBA request Action frame was sent out before 4-way handshake was
completed and the initial 802.11w code ended up dropping the frame
even if MFP was not enabled. While the sending of Action frames this
early is not really a good idea (will break with MFP enabled), we
should not break this for the MFP disabled case.
This patch fixes ieee80211_tx_h_select_key() not to drop management
frames if MFP is disabled. If MFP is enabled, Action frames will be
dropped before keys are set per IEEE 802.11w/D7.0. Other robust
management frames (i.e., Deauthentication and Disassociation frames)
are allowed unprotected prior to key configuration.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the documentation of mesh_nexthop_lookup() in mesh_hwmp.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes documentation of enum mesh_path_flags in mesh.h.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes mesh_plink_close() method as it is unused.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transform calls kmalloc/memset to a single kcalloc.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A new nl80211 command, NL80211_CMD_SET_MGMT_EXTRA_IE, can be used to
add arbitrary IE data into the end of management frames. The interface
allows extra IEs to be configured for each management frame subtype, but
only some of them (ProbeReq, ProbeResp, Auth, (Re)AssocReq, Deauth,
Disassoc) are currently accepted in mac80211 implementation.
This makes it easier to implement IEEE 802.11 extensions like WPS and
FT that add IE(s) into some management frames. In addition, this can
be useful for testing and experimentation purposes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the IEEE80211_RADIOTAP_RATE flag was moved to be conditional, it
was mistakenly left without cpu_to_le32(). Fix that.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is only used within rx.c, so mark it static.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses power constraint level while determining the maximum
transmit power, there by it makes sure that any power mitigation
requirement for the channel in the current regulatory domain is met.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows user space to determine whether a driver supports MFP and
behave properly without having to ask user to configure this in
MFP-optional mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If driver/firmware/hardware does not support CCMP for management
frames, it can now request mac80211 to take care of encrypting and
decrypting management frames (when MFP is enabled) in software. The
will need to add this new IEEE80211_KEY_FLAG_SW_MGMT flag when a CCMP
key is being configured for TX side and return the undecrypted frames
on RX side without RX_FLAG_DECRYPTED flag to use software CCMP for
management frames (but hardware for data frames).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When MFP is enabled, the AP does not allow a STA to associate if an
existing security association exists without first going through SA
Query process. When this happens, the association request is denied
with a new status code ("temporarily rejected") ans Association
Comeback IE is used to notify when the association may be tried again
(i.e., when the SA Query procedure has timed out).
Use the comeback time to update the mac80211 client MLME timer for
next association attempt to minimize waiting time if association is
temporarily rejected.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ieee80211_drop_unencrypted() to decide whether a received frame
should be dropped with management frames, too. If MFP is negotiated,
unprotected robust management frames will be dropped.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending out Action frames, allow ieee80211_tx_skb() to send them
without enforcing do_not_encrypt. These frames will be encrypted if
MFP has been negotiated.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process SA Query Requests for client mode in mac80211. AP side
processing of SA Query Response frames is in user space (hostapd).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new WEXT IW_AUTH_* parameter for setting MFP
disabled/optional/required.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added new SIOCSIWENCODEEXT algorithm for configuring BIP (AES-CMAC)
keys (IGTK).
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new IW_AUTH parameter for setting cipher suite for
multicast/broadcast management frames. This is for full-mac drivers
that take care of RSN IE generation for (re)association request frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add mechanism for managing BIP keys (IGTK) and integrate BIP into the
TX/RX paths.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement Broadcast/Multicast Integrity Protocol for management frame
protection. This patch adds the needed definitions for the new
information element (MMIE) and implementation for the new "encryption"
type (though, BIP is actually not encrypting data, it provides only
integrity protection). These routines will be used by a follow-on patch
that enables BIP for multicast/broadcast robust management frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend CCMP to support encryption and decryption of unicast management
frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add flags for setting STA entries and struct ieee80211_if_sta to
indicate whether management frame protection (MFP) is used.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This modifies hardware flags for powersave to support three different
flags:
* IEEE80211_HW_SUPPORTS_PS - indicates general PS support
* IEEE80211_HW_PS_NULLFUNC_STACK - indicates nullfunc sending in software
* IEEE80211_HW_SUPPORTS_DYNAMIC_PS - indicates dynamic PS on the device
It also adds documentation for all this which explains how to set the
various flags.
Additionally, it fixes a few things:
* a spot where && was used to test flags
* enable CONF_PS only when associated again
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be needed for drivers that set the
IEEE80211_HW_NO_STACK_DYNAMIC_PS flag and still
want to handle dynamic PS.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't accept any arguments we don't handle, and return error codes
instead of using an uninitialised stack value.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel_type really doesn't need to be the only member in
a new structure, so remove the struct. Additionally, remove
the _CONF_CHANGE_HT flag and use _CONF_CHANGE_CHANNEL when the
channel type changes, since that's enough of a change to require
reprogramming the hardware anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all drivers are capable of passing properly aligned frames,
in particular with mesh networking no hardware will support
completely aligning it correctly.
This patch adds code to align the data payload to a 4-byte
boundary in memory for those platforms that require this, or
when CONFIG_MAC80211_DEBUG_PACKET_ALIGNMENT is set.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I missed this during review of "mac80211: Fix tx power setting",
the user_power_level shouldn't be available to the driver but
rather be an internal value used to calculate the value for the
driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes an unused declaration of dot11WEPUndecryptableCount
(an snmp counter) in ieee80211_local structure and its usage in
debugfs.c since this counter is not incremented/decremented anywhere.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes an unused definition of MAX_STA_COUNT in sta_info.h.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes an unused parameter (rx_status) in
ieee80211_rx_mgmt_probe_req(),
in mlme.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes an unnecessary assignment to info
in __ieee80211_tx() , tx.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move to the advertised channel on reception of
a CSA element. This is needed for 802.11h compliance.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last patch fixes a bug that it was not possible to set the channel
manually in the ad hoc mode properly.
Please commit this patches so that we don't need the proprietary
Broadcom driver in the near future anymore.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If you set a fixed BSSID manually, you never want that the driver
change it back, or your ad-hoc mesh network will break into peaces. So
don't do it.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If you set a fixed BSSID and channel it's not necessary to scan for
neighbors to merge, because you really don't want to merge with it. So
don't do it.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Okay, here is the first of the five patches. After applying all
of them you should be able to build/join huge city mesh networks
(e.g. with the OLSR protocol) with the most of the mac80211 wireless
drivers by setting a fixed BSSID in the ad hoc mode. (If you found no
other bug/problem.) This was not specified in the original standard,
but is a widely used de facto standard.
The first patch now completely disallow to set multicast MAC addresses
as BSSID. The behavior before was really strange.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The set_key callback now seems rather odd, passing a MAC address
instead of a station struct, and a local address instead of a
vif struct. Change that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Bob Copeland <me@bobcopeland.com> [ath5k]
Acked-by: Ivo van Doorn <ivdoorn@gmail.com> [rt2x00]
Acked-by: Christian Lamparter <chunkeey@web.de> [p54]
Tested-by: Kalle Valo <kalle.valo@nokia.com> [iwl3945]
Tested-by: Samuel Ortiz <samuel@sortiz.org> [iwl3945]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes sparse warnings:
net/mac80211/util.c:355:6: warning: symbol
'ieee80211_wake_queue_by_reason' was not declared. Should it be static?
net/mac80211/util.c:385:6: warning: symbol
'ieee80211_stop_queue_by_reason' was not declared. Should it be static?
Thanks to Johannes Berg for reporting this.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
power_level in ieee80211_conf is being used for more than one
purpose. It being used as user configured power limit and the
final power limit given to the driver. By doing so, except very
first time, the tx power limit is taken from min(chan->max_power,
local->hw.conf.power_level) which is not what we want. This patch
defines a new memeber in ieee80211_conf which is meant only for
user configured power limit.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can simply use conf_is_ht() check where needed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the station info is flushed before calling set_disassoc
in ieee80211_stop, the power save timer is never cancelled
when the driver is unloaded. Hence the timer cancellation has
to be done in ieee80211_stop itself.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables mac80211 to send a null frame and also to
check for tim in the beacon if dynamic power save is enabled.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
a) hw_config() should not be called from siwpower() for the drivers which do not support
dynamic powersave.
b) IEEE80211_HW_NO_STACK_DYNAMIC_PS needs to be verified in set_associated() also before
enabling the power save timers.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a null data frame is generated from mac80211, it goes through
master_start_xmit and not through subif_start_xmit. Hence for the
power save timer to be triggered while sending this null data frame
also, the timer has to be reset from master_start_xmit.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As TKIP is not updated to new security needs which arise when
TKIP is used to encrypt A-MPDU aggregated data frames, IEEE802.11n
does not allow any cipher other than CCMP (Which has new extensions
defined) as pairwise cipher between HT peers.
When such configuration (TKIP/WEP in HT) is forced, we still
associate in non-HT mode (11a/b/g).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wlan0: switched to short barker preamble (BSSID=00:01:aa:bb:cc:dd)
wlan0: switched to short slot (BSSID=) <something is missing here>
should be:
wlan0: switched to short barker preamble (BSSID=00:01:aa:bb:cc:dd)
wlan0: switched to short slot (BSSID=00:01:aa:bb:cc:dd)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After launching mesh discovery in tx path, reference count was not being
decremented. This was preventing module unload.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix (delete) more mac80211 kernel-doc:
Warning(linux-2.6.28-git13//include/net/mac80211.h:375): Excess struct/union/enum/typedef member 'retry_count' description in 'ieee80211_tx_info'
Warning(linux-2.6.28-git13//net/mac80211/sta_info.h:308): Excess struct/union/enum/typedef member 'last_txrate' description in 'sta_info'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/mac80211/ht.c: In function ‘ieee80211_start_tx_ba_session’:
net/mac80211/ht.c:472: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a panic that might occur, if the device is part of a mesh
and tries to send with a higher rate index than "0".
kernel BUG at net/mac80211/rate.c:239!
invalid opcode: 0000 [#1] SMP
[...]
Call Trace:
<IRQ> <0> ? invoke_tx_handlers+0x474/0xb57 [mac80211]
? __ieee80211_tx_prepare+0x260/0x2a8 [mac80211]
? ieee80211_master_start_xmit+0x300/0x43a [mac80211]
? __qdisc_run+0xde/0x1da
? net_tx_action+0xb4/0x102
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changing mode on an interface is not allowed if IBSS is disabled for the
current channel. That restriction should only apply when switching to
the ad-hoc mode, as it was prior to "cfg80211: handle SIOCGIWMODE/SIOCSIWMODE".
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following WARNING (caused by rix_to_ndx): "
>WARNING: at net/mac80211/rc80211_minstrel.c:69 minstrel_rate_init+0xd2/0x33a [mac80211]()
>[...]
>Call Trace:
> warn_on_slowpath+0x51/0x75
> _format_mac_addr+0x4c/0x88
> minstrel_rate_init+0xd2/0x33a [mac80211]
> print_mac+0x16/0x1b
> schedule_hrtimeout_range+0xdc/0x107
> ieee80211_add_station+0x158/0x1bd [mac80211]
> nl80211_new_station+0x1b3/0x20b [cfg80211]
The reason is that I'm experimenting with "g" only mode on a 802.11 b/g card.
Therefore rate_lowest_index returns 4 (= 6Mbit, instead of usual 0 = 1Mbit).
Since mi->r array is initialized with zeros in minstrel_alloc_sta,
rix_to_ndx has a hard time to find the 6Mbit entry and will trigged the WARNING.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements dynamic power save for mac80211. Basically it
means enabling power save mode after an idle period. Implementing it
dynamically gives a good compromise of low power consumption and low
latency. Some hardware have support for this in firmware, but some
require the host to do it.
The dynamic power save is implemented by adding an timeout to
ieee80211_subif_start_xmit(). The timeout can be enabled from userspace
with Wireless Extensions. For example, the command below enables the
dynamic power save and sets the time timeout to 500 ms:
iwconfig wlan0 power timeout 500m
Power save now only works with devices which handle power save in firmware.
It's also disabled by default and the heuristics when and how to enable is
considered as a policy decision and will be left for the userspace to handle.
In case the firmware has support for this, drivers can disable this feature
with IEEE80211_HW_NO_STACK_DYNAMIC_PS.
Big thanks to Johannes Berg for the help with the design and code.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a preparation for the dynamic power save support. In future there are
two paths to stop the master queues and we need to track this properly to
avoid starting queues incorrectly. Implement this by adding a status
array for each queue.
The original idea and design is from Johannes Berg, I just did
the implementation based on his notes. All the bugs are mine, of course.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also disable power save when disassociated. It makes no sense to have
power save enabled while disassociated.
iwlwifi seems to have this check in the driver, but it's better to do this
in mac80211 instead.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In stress testing p54usb, the WARN_ON() in ieee80211_tasklet_handler() was
triggered; however, there is no logging of the received value for packet
type. Adding that feature will improve the warning.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a typo in ieee80211_send_assoc(), net/mac80211/mlme.c.
The error is usage of a wrong member when building
the ie80211 management frame (it should be assoc_req, and not reassoc_req).
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we do not currently report HT rates (MCS index) in radiotap
header for HT rates, we should not claim the rate is present. The rate
octet itself is used as padding in this case, so only the it_present
flag needs to be removed in case of HT rates.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a STA roams back to the same AP before the previous STA entry has
expired, a new STA entry is not added in mac80211. However, a Layer 2
Update frame still needs to be transmitted to update layer 2 devices
about the new location for the STA. Without this, switches may
continue to forward frames to the previous (now incorrect) port when
STA roams between APs.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds option for HT-enabled drivers to report HT rates
(HT20/HT40, short GI, MCS index) to mac80211. These rates are
currently not in the rate table, so the rate_idx is used to indicate
MCS index.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HT management is done differently for AP and STA modes, unify
to just the ->config() callback since HT is fundamentally a
PHY property and cannot be per-BSS.
Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote
the channel type ( NO_HT, HT20, HT40+, HT40- ).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds signal strength and transmission bitrate
to the station_info of nl80211.
Signed-off-by: Henning Rogge <rogge@fgan.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unneeded member (skbuff) from
ieee80211_ibss_add_sta() method in its declaration (in ieee80211_i.h)
and its callers (in rx.c and mlme.c)
This patch removes unneeded member from struct ieee80211_rx_data
in ieee80211_i.h.
(Originally posted as two patches. -- JWL)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AP mode operations are seriously affected if mac80211 runs through a
multi-second scan while the AP is trying to send Beacon frames on the
operation channel. While this could be implemented in a way that does
not cause too many problems, it is not very simple and will require
synchronization with Beacon frame scheduling in the drivers (scan one
channel at a time between Beacon frames). Furthermore, such scanning
takes quite a bit longer time and existing userspace applications
would be likely to timeout while waiting for the results.
For now, just refuse requests for new scans (SIOCSIWSCAN) when in AP
mode. In practice, this moves the rejection from iwl* drivers into
mac80211 to make it apply to every mac80211-based driver.
This issue shows up in associated stations getting disconnected when
something (e.g., Network Manager) requests a scan while the interface
is in AP mode. When doing this continuously (e.g., NM does it every 120
seconds), the network gets close to useless.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces the newly introduced sta_notify_ps function,
which can be used to notify the driver about every power state
transition for all associated stations, by integrating its functionality
back into the original sta_notify callback.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure sparse checks endianness when run on mac80211/cfg80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no driver that actually does fragmentation on the
device, and the callback is buggy (when it returns an error,
mac80211's fragmentation status is changed so reading the
frag threshold from userspace reads the new value despite
the error). Let's just remove it, if we really find some
hardware supporting it we can add it back later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers will support this, obviously, but this forces them to
set it up properly.
(This includes the fix posted as "mac80211: fix ifmodes check" and
tested in wireless-testing by Hin-Tak and others. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_hw_config can return an error when the hardware
has rfkill enabled. A WARN_ON() is too harsh for this
failure as it is a valid scenario. Only comment this warning
as we would like to have it back when rfkill is integrated into
mac80211.
Also reintroduce propagation of error if ieee80211_hw_config fails
in ieee80211_config_beacon.
This patch partially reverts patch:
5f0387fc3337ca26f0745f945f550f0c3734960f
"mac80211: clean up ieee80211_hw_config errors"
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unnecessary parameter in ieee80211_beacon_add_tim() and
removes unneeded definition and assignment for bdev (instance of net_device) in
ieee80211_beacon_get() and in ieee80211_get_buffered_bc()
(all in tx.c).
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is necessary in order to provide a proper Access point support for p54.
Unfortunately for us, there is no documented way to disable the interfering
power save buffering mechanism in firmware completely.
Therefore we give in and notify the driver through our new sta_notify_ps callback,
so that we can update the filter state.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some access points (e.g. Sitecom WL-174) use an empty string as hidden SSID.
Signed-off-by: Fabio Rossi <rossi.f@inwind.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
further reducing wext code in mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the SIOCGIWNAME handling from mac80211 to cfg80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new NL80211_CMD_SET_WIPHY attributes
NL80211_ATTR_WIPHY_FREQ and NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET to allow
userspace to set the operating channel (e.g., hostapd for AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station goes to PS mode to scan, it will then send
probe requests without the PS bit set. mac80211 will take
that as indication that the station woke up, but it didn't.
This patch changes mac80211 to only consider doze->wake
transitions on data frames to to fix that issue.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reorders calls during disassociation in
ieee80211_set_disassoc function.
Since sta_info_unlink calls sta_notify(REMOVE) it will
remove the station representing AP from the driver before
it has disassociated from it using bss_info_changed callback.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems like proper etiquette to let other stations know when we are
going down in either STA or IBSS mode. This also notifies userland, so
wpa_supplicant doesn't get confused.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After fixing zd1211rw: use unaligned safe memcmp() in-place of
compare_ether_addr(), I started to see kernel log messages detailing
unaligned access:
Kernel unaligned access at TPC[100f7f44] sta_info_get+0x24/0x68 [mac80211]
As with the aforementioned patch, the unaligned access was eminating
from a compare_ether_addr() call. Concerned that whilst it was safe to
assume that unalignment was the norm for the zd1211rw, and take
preventative measures, it may not be the case or acceptable to use the
easy fix of changing the call to memcmp().
My research however indicated that it was OK to do this, as there are
a few instances where memcmp() is the preferred mechanism for doing
mac address comparisons throughout the module.
Signed-off-by: Shaddy Baddah <shaddy_baddah@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a disassoc packet is received from the AP with a reason code of
'leaving the BSS', mac80211 should go into DISABLED state just as it
would do if the AP suddenly went away for some reason, as that is what
will happen shortly after the AP leaves anyway.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit 9ea2c74 named "mac80211/drivers: rewrite the rate control API",
the meaning of status.rates[i].count was changed from number of retries
to total number of tries. As a result, the pid rate-setting algorithm fails
because every packet appears to have needed a retransmit.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes minstrel the default rate control algorithm
for mac80211. For more information see:
http://wireless.kernel.org/en/developers/Documentation/mac80211/RateControl/minstrel
If someone can come up with a better algorithm they get a prize
(undisclosed).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211's ieee80211_register_hw() is often called within the
probe path so it cannot assume the device's driver structure
has been attached yet so to create a workqueue instead of
using driver->name use the wiphy's phy%d name. The name doesn't
really matter anyway.
This should fix sporadic oopses found when we race to beat the
driver pointer setting. Not even sure how this was working properly.
http://www.kerneloops.org/search.php?search=ieee80211_register_hw
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds country IE parsing to mac80211 and enables its usage
within the new regulatory infrastructure in cfg80211. We parse
the country IEs only on management beacons for the BSSID you are
associated to and disregard the IEs when the country and environment
(indoor, outdoor, any) matches the already processed country IE.
To avoid following misinformed or outdated APs we build and use
a regulatory domain out of the intersection between what the AP
provides us on the country IE and what CRDA is aware is allowed
on the same country.
A secondary device is allowed to follow only the same country IE
as it make no sense for two devices on a system to be in two
different countries.
In the case the AP is using country IEs for an incorrect country
the user may help compliance further by setting the regulatory
domain before or after the IE is parsed and in that case another
intersection will be performed.
CONFIG_WIRELESS_OLD_REGULATORY is supported but requires CRDA
present.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the kernel trace when user tries to set
ad-hoc mode on non IBSS channel.
e.g iwconfig wlan0 chan 36 mode ad-hoc
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove redundant argument comments in files of net/*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unnecessary #include <linux/netdevice.h> from
/net/mac80211/mlme.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch eliminates sparse warnings in pid rate scale algorithm
'debugfs: allow access to signed values' patch hit the dead end
year ago w/o much echo so I guess there is no real need to address this
properly.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete kernel-doc struct descriptions for fields that don't exist:
Warning(include/net/mac80211.h:1263): Excess struct/union/enum/typedef member 'conf_ht' description in 'ieee80211_ops'
Warning(net/mac80211/sta_info.h:309): Excess struct/union/enum/typedef member 'addr' description in 'sta_info'
Warning(net/mac80211/sta_info.h:309): Excess struct/union/enum/typedef member 'aid' description in 'sta_info'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Johannes Berg <johannes@sipsolutions.net>
cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh interfaces are currently opened with the FIF_ALLMULTI rx filter flag set,
however there is no BSSID in mesh so BSSID filtering should be disabled by
setting the FIF_OTHER_BSS flag as well. Also explicitly call
ieee80211_configure_filter for mesh.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozbit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before ieee80211_notify_mac() was added, it was presented with the
use case of using it to tell mac80211 that the association may
have been lost because the firmware crashed/reset.
Since then, it has also been used by iwlwifi to (slightly) speed
up re-association after resume, a workaround around the fact that
mac80211 has no suspend/resume handling yet. It is also not used
by any other drivers, so clearly it cannot be necessary for "good
enough" suspend/resume.
Unfortunately, the callback suffers from a severe problem: It only
works for station mode. If suspend/resume happens while in IBSS or
any other mode (but station), then the callback is pointless.
Recently, it has created a number of locking issues, first because
it required rtnl locking rather than RCU due to calling sleeping
functions within the critical section, and now because it's called
by iwlwifi from the mac80211 workqueue that may not use the rtnl
because it is flushed under rtnl.
(cf. http://bugzilla.kernel.org/show_bug.cgi?id=12046)
I think, therefore, that we should take a step back, remove it
entirely for now and add the small feature it provided properly.
For suspend and resume we will need to introduce new hooks, and for
the case where the firmware was reset the driver will probably
simply just pretend it has done a suspend/resume cycle to get
mac80211 to reprogram the hardware completely, not just try to
connect to the current AP again in station mode. When doing so, we
will need to take into account locking issues and possibly defer
to schedule_work from within mac80211 for the resume operation,
while the suspend operation must be done directly.
Proper suspend/resume should also not necessarily try to reconnect
to the current AP, the time spent in suspend may have been short
enough to not be disconnected from the AP, mac80211 will detect
that the AP went out of range quickly if it did, and if the
association is lost then the AP will disassoc as soon as a data
frame is sent. We might also take into account WWOL then, and
have mac80211 program the hardware into such a mode where it is
available and requested.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_notify_mac() function uses ieee80211_sta_req_auth() which
in turn calls ieee80211_set_disassoc() which calls a few functions that
need to be able to sleep, so ieee80211_notify_mac() cannot use RCU
locking for the interface list and must use rtnl locking instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/mac80211/debugfs_sta.c
The trailing zero was written to state[4], it's out of bounds.
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the addition of basic rate set and TX queue parameter
configuration and confirmation that power save buffering is
working again, mac80211 is now in state that allows AP mode to be
used without major problems. Consequently, it is time to allow this
mode to be enabled without having to patch the kernel.
AP mode requires hostapd for management frame processing and as such,
configuring this mode is only allowed through cfg80211 (not with
iwconfig and WEXT).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In previous code all the rates were marked as basic.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new attribute, NL80211_ATTR_WIPHY_TXQ_PARAMS, that can be used with
NL80211_CMD_SET_WIPHY for userspace (e.g., hostapd) to set TX queue
parameters (txop, cwmin, cwmax, aifs).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new attribute, NL80211_ATTR_BSS_BASIC_RATES, that can be used with
NL80211_CMD_SET_BSS for userspace (e.g., hostapd) to set which rates are
in the basic rate set.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send a notification to the driver on succesful
reception of an ADDBA response, add IEEE80211_AMPDU_TX_RESUME
for this purpose.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the SSID from the driver API since now there is no
driver that requires knowing the SSID and I think it's
unlikely that any hardware design that does require the
SSID will play well with mac80211.
This also removes support for setting the SSID in master
mode which will require a patch to hostapd to not try.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a constant from the 802.11 specification.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch prints reason code for deauth/dissoc frames to give users
more ideas what's happened for the disconnection.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One parameter wasn't described and one I forgot to update when
renaming it; also update TBDs in sta_info.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless HW without any dedicated queues for aggregation
do not need the ampdu_queues mechanism present right now
in mac80211. Since mac80211 is still incomplete wrt TX MQ
changes, do not allow aggregation sessions for drivers that
set ampdu_queues.
This is only an interim hack until Intel fixes the requeue issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliminate the vif.type check in ieee80211_rx_h_action. This check is
unnecessary (these action frames can be handled by all interface types) and
currently prevents, for example, AP interfaces from handling BACK action frames
such as ADDBA and DELBA requests.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A warning would be printed for every packet that
is transmitted if the rate control information isn't
setup. Change this to WARN_ON_ONCE.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not know what max power to allow until a device is targeting
a channel, therefore only allow changing tx power if a channel is defined.
Also make use of the channel's max power setting as defined by
regulatory rules before allowing the user to use the requested power
setting. If the user asked us to figure it out we use the max allowed
by regulatory.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add a check on the return value of dev_alloc_skb() in
ieee80211_sta_join_ibss() in net/mac80211/mlme.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never clearly defined the semantics of the sta_notify callback
and it was originally posted for iwlwifi which still doesn't use
it at all. With the recent HT rework ath9k started relying on it,
but I made a mistake there in that I made ath9k assume the HT
information has already been filled in at sta_notify time. This
isn't a hard thing to do, so do it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The two new commands are NL80211_CMD_GET_MESH_PARAMS and
NL80211_CMD_SET_MESH_PARAMS. There is a new attribute enum,
NL80211_ATTR_MESH_PARAMS, which enumerates the various mesh configuration
parameters.
Moved struct mesh_config from mac80211/ieee80211_i.h to net/cfg80211.h.
nl80211_get_mesh_params and nl80211_set_mesh_params unpack the netlink messages
and ask the driver to get or set the configuration. This is done via two new
function stubs, get_mesh_params and set_mesh_params, in struct cfg80211_ops.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed that when for some reason [1] the probe or auth times
out, wpa_supplicant doesn't realise this and only tries the next
AP when it runs into its own timeout, which is ten seconds, and
that's quite long. Fix this by making mac80211 notify userspace
that it didn't associate.
[1] my wrt350n in mixed B/G/HT mode often runs into this, maybe
it's because one of the antennas is broken off and for whatever
reason it decides to use that antenna to transmit the response
frames (auth, probe); I do see beacons fine so it's not totally
broken. Works fine in pure-G mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"Clearing" the rate control algorithm is pointless, none of
the algorithms actually uses this operation and it's not even
invoked properly for all channel switching. Also, there's no
need to since rate control algorithms work per station.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enhances minstrel's performance for non-MRR setups,
by preventing it from sampling slower rates with >95% success
probability and by putting at least 1 non-sample frame between
several sample frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
