The driver already supports the 1 protocol support, so just add it to
the MODULE_DEVICE_TABLE entry so it properly picks up these devices.
Thanks to Jouni Rynö for pointing this out.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
open() will never succeed, as we always return -ENODEV. Fix this
obvious bug.
Thanks to Jouni Ryno for reporting it.
Reported-by: Jouni Ryno <Jouni.Ryno@fmi.fi>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
zd_op_tx() must not return an arbitrary error value since that can
leave mac80211 trying to retransmit the frame and with the extra data
pushed into the beginning of the skb on every attempt, this will end up
causing a kernel panic (skb_under_panic from skb_push call). This can
happen, e.g., when ejecting the device when associated.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All 802.11n PCI devices (Cardbus, PCI, mini-PCI) require
serialization of IO when on non-uniprocessor systems. PCI
express devices not not require this.
This should fix our only last standing open ath9k kernel.org
bugzilla bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=12110
A port is probably required to older kernels and I can work on
that.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
acpi-wmi: unsigned cannot be less than 0
thinkpad-acpi: fix module autoloading for older models
acer-wmi: Unmark as 'experimental'
acpi-wmi: Unmark as 'experimental'
acer-wmi: double free in acer_rfkill_exit()
platform/x86: depends instead of select for laptop platform drivers
asus-laptop: use select instead of depends on
eeepc-laptop: restore acpi_generate_proc_event()
asus-laptop: restore acpi_generate_proc_event()
acpi: check for pxm_to_node_map overflow
ACPI: remove doubled status checking
ACPI suspend: Blacklist Toshiba Satellite L300 that requires to set SCI_EN directly on resume
Revert "ACPI: make some IO ports off-limits to AML"
suspend: switch the Asus Pundit P1-AH2 to old ACPI sleep ordering
The following oops has been reported when dm-crypt runs over a loop device.
...
[ 70.381058] Process loop0 (pid: 4268, ti=cf3b2000 task=cf1cc1f0 task.ti=cf3b2000)
...
[ 70.381058] Call Trace:
[ 70.381058] [<d0d76601>] ? crypt_dec_pending+0x5e/0x62 [dm_crypt]
[ 70.381058] [<d0d767b8>] ? crypt_endio+0xa2/0xaa [dm_crypt]
[ 70.381058] [<d0d76716>] ? crypt_endio+0x0/0xaa [dm_crypt]
[ 70.381058] [<c01a2f24>] ? bio_endio+0x2b/0x2e
[ 70.381058] [<d0806530>] ? dec_pending+0x224/0x23b [dm_mod]
[ 70.381058] [<d08066e4>] ? clone_endio+0x79/0xa4 [dm_mod]
[ 70.381058] [<d080666b>] ? clone_endio+0x0/0xa4 [dm_mod]
[ 70.381058] [<c01a2f24>] ? bio_endio+0x2b/0x2e
[ 70.381058] [<c02bad86>] ? loop_thread+0x380/0x3b7
[ 70.381058] [<c02ba8a1>] ? do_lo_send_aops+0x0/0x165
[ 70.381058] [<c013754f>] ? autoremove_wake_function+0x0/0x33
[ 70.381058] [<c02baa06>] ? loop_thread+0x0/0x3b7
When a table is being replaced, it waits for I/O to complete
before destroying the mempool, but the endio function doesn't
call mempool_free() until after completing the bio.
Fix it by swapping the order of those two operations.
The same problem occurs in dm.c with md referenced after dec_pending.
Again, we swap the order.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
In the async encryption-complete function (kcryptd_async_done), the
crypto_async_request passed in may be different from the one passed to
crypto_ablkcipher_encrypt/decrypt. Only crypto_async_request->data is
guaranteed to be same as the one passed in. The current
kcryptd_async_done uses the passed-in crypto_async_request directly
which may cause the AES-NI-based AES algorithm implementation to panic.
This patch fixes this bug by only using crypto_async_request->data,
which points to dm_crypt_request, the crypto_async_request passed in.
The original data (convert_context) is gotten from dm_crypt_request.
[mbroz@redhat.com: reworked]
Cc: stable@kernel.org
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-io calls bio_get_nr_vecs to get the maximum number of pages to use
for a given device. It allocates one additional bio_vec to use
internally but failed to respect BIO_MAX_PAGES, so fix this.
This was the likely cause of:
https://bugzilla.redhat.com/show_bug.cgi?id=173153
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix an error introduced in dm-table-rework-reference-counting.patch.
When there is failure after table initialization, we need to use
dm_table_destroy, not dm_table_put, to free the table.
dm_table_put may be used only after dm_table_get.
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When renaming a mapped device validate the length of the new name.
The rename ioctl accepted any correctly-terminated string enclosed
within the data passed from userspace. The other ioctls enforce a
size limit of DM_NAME_LEN. If the name is changed and becomes longer
than that, the device can no longer be addressed by name.
Fix it by properly checking for device name length (including
terminating zero).
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Impact: help prevent extinction of species
The Tasmanian Devil is a shy iconic Australian creature named for its
spine-chilling screech. It is threatened with extinction due to a
scientifically interesting but horrific transmissible facial cancer.
This one is standing in for Tux for one release using the far less-known
Devil Facial Tux Disguise.
Save The Tasmanian Devil http://tassiedevil.com.au
Signed-off-by: Linux.conf.au Hobart Team <contact@marchsouth.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
include/linux/pci-acpi.h:74:
typedef u32 acpi_status;
result is unsigned, so an error returned by acpi_bus_register_driver()
will not be noticed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Looking at the source, there seems to be a missing * to match my DMI
string. I mean for newer IBM and Lenovo's laptops you match either one
of the following:
MODULE_ALIAS("dmi:bvnIBM:*:svnIBM:*:pvrThinkPad*:rvnIBM:*");
MODULE_ALIAS("dmi:bvnLENOVO:*:svnLENOVO:*:pvrThinkPad*:rvnLENOVO:*");
While for older Thinkpads, you do this (for instance):
IBM_BIOS_MODULE_ALIAS("1[0,3,6,8,A-G,I,K,M-P,S,T]");
with IBM_BIOS_MODULE_ALIAS being MODULE_ALIAS("dmi:bvnIBM:bvr" __type "ET??WW")
Note there's no * terminating the string. As result, udev doesn't load
anything because modprobe cannot find anything matching this (my
machine actually):
udevtest: run: '/sbin/modprobe dmi:bvnIBM:bvr1IET71WW(2.10):bd06/16/2006:svnIBM:pn236621U:pvrNotAv
Signed-off-by: Mathieu Chouquet-Stringer <mchouque@free.fr>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
This driver has been around and used long enough that we can drop the
'experimental'.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI-WMI isn't experimental anymore, and there are other drivers that now
depend on it that aren't either.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
This is acer_rfkill_exit() from drivers/platform/x86/acer-wmi.c.
The code frees wireless_rfkill->data again instead of
bluetooth_rfkill->data.
This was found using a code checker (http://repo.or.cz/w/smatch.git/).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
"I hate `select' and will gleefully leap on any s/select/depends/ patch,
whether it works or not :)"
Andrew Morton
select INPUT is not needed here, because if someone doesn't want INPUT,
he won't want these drivers either.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Like thinkpad_acpi or eeepc-laptop, asus-laptop will
now use "select" instead of "depends on"
for LEDS_CLASS, NEW_LEDS and BACKLIGHT_CLASS_DEVICE
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Restore acpi_generate_proc_event() for backward
compatibility with old acpi scripts.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Restore acpi_generate_proc_event() for backward
compatibility with old acpi scripts.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
It is hardly (if ever) possible but in case of broken _PXM entry we could
reach out of pxm_to_node_map array bounds in acpi_map_pxm_to_node() call.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
There was a misplaced status test (two consequent tests without a
statement in between) in acpi_bus_init for ages. Remove it, since the
function which should be checked (acpi_os_initialize1) has BUG_ONs on
failure paths.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit 5ec5d38a1c.
because it caused spurious dmesg warmings.
We'll implement the check for off-limit ports
in a more clever way in the future.
http://bugzilla.kernel.org/show_bug.cgi?id=12758
Signed-off-by: Len Brown <len.brown@intel.com>
Switch the Asus Pundit P1-AH2 (M2N8L motherboard) to the old ACPI 1.0
sleep ordering by default. Without this it will not suspend/resume
correctly.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Tested-by: Dustin Kirkland <kirkland@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
It fails on the following systems:
- RTL8169sc/8110sc (XID 18000000)
reported by Tim Durack <tdurack@gmail.com> (x86)
- RTL8169sb/8110sb (XID 10000000)
reported by Mikael Pettersson <mikpe@it.uu.se> (ARM)
The patch appeared to work on x86 for the following systems:
RTL8169sb/8110sb 10000000 PCI (EXT)
RTL8110s 04000000 PCI (EXT)
RTL8102e 24a00000 PCI-E (LOM)
RTL8168c/8111c 3c2000c0 PCI-E (LOM)
RTL8168b/8111b 38000000 PCI-E (LOM)
RTL8168b/8111b 38000000 PCI-E (EXT)
The patch exposes two problems:
1) while not completely wrong, mac addresses are not read correctly
from the EEPROM
2) the MAC address registers are not correctly set
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
It shortens the code and fixes the current pci_unmap leak with
padded skb reported by Dave Jones.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC drivers/parisc/sba_iommu.o
drivers/parisc/sba_iommu.c:1373: error: expected identifier or '('
before '}' token
make[2]: *** [drivers/parisc/sba_iommu.o] Error 1
make[1]: *** [drivers/parisc] Error 2
make: *** [drivers] Error 2
Don't know how this has gone missed for so long... clearly I need
to do builds on my C8000 more often.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The L0s workaround should be moved into a pci quirk and so it is not
necessary in the driver. This update removes the L0s workaround from the
igb driver.
This was the second half of the PCI quirk patch that Matthew Wilcox did
not pick up when he picked up the quirk patch.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SystemACE driver does not handle an empty CF slot gracefully. An
empty CF slot ends up hanging the system. This patch adds a check for
the CF state and stops trying to process requests if the slot is empty.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (31 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k4.
[SCSI] qla2xxx: Correct overwrite of pre-assigned init-control-block structure size.
[SCSI] qla2xxx: Correct truncation in return-code status checking.
[SCSI] qla2xxx: Correct vport delete bug.
[SCSI] qla2xxx: Use correct value for max vport in LOOP topology.
[SCSI] qla2xxx: Correct address range checking for option-rom updates.
[SCSI] fcoe: Change fcoe receive thread nice value from 19 (lowest priority) to -20
[SCSI] fcoe: fix handling of pending queue, prevent out of order frames (v3)
[SCSI] fcoe: Out of order tx frames was causing several check condition SCSI status
[SCSI] fcoe: fix kfree(skb)
[SCSI] fcoe: ETH_P_8021Q is already in if_ether and fcoe is not using it anyway
[SCSI] libfc: do not change the fh_rx_id of a recevied frame
[SCSI] fcoe: Correct fcoe_transports initialization vs. registration
[SCSI] fcoe: Use setup_timer() and mod_timer()
[SCSI] libfc, fcoe: Remove unnecessary cast by removing inline wrapper
[SCSI] libfc, fcoe: Cleanup function formatting and minor typos
[SCSI] libfc, fcoe: Fix kerneldoc comments
[SCSI] libfc: Cleanup libfc_function_template comments
[SCSI] libfc: check for err when recv and state is incorrect
[SCSI] libfc: rename rp to rdata in fc_disc_new_target()
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_piix: add workaround for Samsung DB-P70
libata: Keep shadow last_ctl up to date during resets
sata_mv: fix MSI irq race condition
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (10978): Report tuning algorith correctly
V4L/DVB (10977): STB6100 init fix, the call to stb6100_set_bandwidth needs an argument
V4L/DVB (10976): Bug fix: For legacy applications stv0899 performs search only first time after insmod.
V4L/DVB (10975): Bug: Use signed types, Offsets and range can be negative
V4L/DVB (10974): Use Diseqc 3/3 mode to send data
V4L/DVB (10972): zl10353: i2c_gate_ctrl bug fix
V4L/DVB (10834): zoran: auto-select bt866 for AverMedia 6 Eyes
V4L/DVB (10832): tvaudio: Avoid breakage with tda9874a
V4L/DVB (10789): m5602-s5k4aa: Split up the initial sensor probe in chunks.
Remove flash size check which made sense only for ancient
boards with 1MB flash. The check is based on values read
from specific locations and fails with firmware size changes.
This prevents driver from getting right mac addresses.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mv643xx_eth_open() is called to up an interface, port_start()
will first re-program the unicast address filter, and then
re-initialise the PORT_CONFIG register, but that will disable unicast
promiscuous mode if it was enabled by the unicast address filter setup.
This isn't a problem on ifconfig up, as ->set_rx_mode() will be called
shortly afterwards which will program the filters again, but it does
trigger when changing the MTU, which calls mv643xx_eth_stop() and then
mv643xx_eth_open() by hand to repopulate the receive rings with skbuffs
of the new size.
Swap the initialisation of the PORT_START register and the call to
the unicast filter setup function to fix this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The openprom module is missing the char-major-10-139 alias that would
cause it to be auto-loaded when a device of that type is opened. This
patch adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC variant in the 405EX and 405EXr chips needs the "440EP" type clock
control workaround to avoid lockups of the Rx side during reset.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple unicast address support appears to have been broken with the
change to support net_device_ops. This a regression from 2.6.28 to 2.6.29.
I'm not 100% on whether ndo_set_multicast_list can be NULL after this
or not. If ndo_set_rx_mode is set everything _should_ be using it.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Dave Jones <davej@redhat.com>
The dma-debug changes caught that this driver uses the
wrong DMA mapping length when skb_padto() does something.
With suggestions from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_map_sg could return a value different to 'nents' argument of
dma_map_sg so the ide stack needs to save it for the later usage
(e.g. for_each_sg).
The ide stack also needs to save the original sg_nents value for
pci_unmap_sg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
[bart: backport to Linus' tree]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
since it fails the virt_to_page() translation check with DEBUG_VIRTUAL
enabled.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: backport to Linus' tree]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Samsung DB-P70 somehow botched the first ICH9 SATA port. The board
doesn't expose the first port but somehow SStatus reports link online
while failing SRST protocol leading to repeated probe failures and
thus long boot delay.
Because the BIOS doesn't carry any identifying DMI information, the
port can't be blacklisted safely. Fortunately, the controller does
have subsystem vendor and ID set. It's unclear whether the subsystem
IDs are used only for the board but it can be safely worked around by
disabling SIDPR access and just using SRST works around the problem.
Even when the workaround is triggered on an unaffected board the only
side effect will be missing SCR access.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Joseph Jang <josephjang@gmail.com>
Reported-by: Jonghyon Sohn <mrsohn@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata keeps a shadow copy of the ATA CTL register (which is write only),
and only writes to the hardware when the required value doesn't match
the shadow. However this copy wasn't being maintained when performing
reset functions. This could cause problems for the first operation after
a reset when the correct value might not be written to the CTL register.
This problem was observed when hotplugging a drive: the identify command
was being issued with interrupts enabled, when they should have been
disabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a (rare) race condition in mv_interrupt() when using MSI.
The value of hpriv->main_irq_mask_addr can change on on the fly,
and without this patch we could end up writing back a stale copy
to the hardware.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*netif_rx_* functions is obsolete and removed in newer kernels so
we need to use corresponding *napi_* functions instead.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in Hz not kHz, and a comment incorrectly says MHz instead of Hz. I
don't know if this caused real problems anywhere
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For legacy applications stv0899 performs search only first time after insmod
due to not set DVBFE_ALGO_SEARCH_AGAIN bit
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> posted a patch series
to linux-pci to fix a wrong assumption about pci_bus->self==NULL for
all PCI host bus controllers. While PARISC platforms to not behave
this way, I prefer to have the code consistent across architectures.
The following patch replaces pci_bus->self with pci_bus->parent when
used as a test to check for "root bus controller".
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Fix compile warnings:
drivers/scsi/zalon.c: In function `zalon_probe':
drivers/scsi/zalon.c:140: warning: passing arg 1 of `dev_driver_string' from incompatible pointer type
drivers/scsi/zalon.c:140: warning: passing arg 1 of `dev_name' from incompatible pointer type
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
commit 11c3b5c3e0
Author: Greg Kroah-Hartman <gregkh@suse.de>
Date: Tue Dec 16 12:24:56 2008 -0800
driver core: move klist_children into private structure
Broke our parisc build pretty badly because we touch the klists directly
in three cases (AGP, SBA and GSC). Although GregKH will revert this
patch, there's no reason we should be using the iterators directly, we
can just move to the standard device_for_each_child() API.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Convert the PS3 Video RAM Storage Driver from an MTD driver to a plain block
device driver.
The ps3vram driver exposes unused video RAM on the PS3 as a block device
suitable for storage or swap. Fast data transfer is achieved using a local
cache in system RAM and DMA transfers via the GPU.
The new driver is ca. 50% faster for reading, and ca. 10% for writing.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
zl10353 i2c-gate was always closed and due to that devices having tuner
behind i2c-gate were broken. Add module configuration which allows disabling
i2c-gate only when really needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (f75375s) Remove unnecessary and confusing initialization
hwmon: (it87) Properly decode -128 degrees C temperature
hwmon: (lm90) Document support for the MAX6648/6692 chips
hwmon: (abituguru3) Fix I/O error handling
* 'fixes-20090312' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/pci:
PCIe: portdrv: call pci_disable_device during remove
pci: Fix typo in message while disabling HT MSI mapping
pci: don't disable too many HT MSI mapping
powerpc/pseries: The RPA PCI hotplug driver depends on EEH
PCIe: AER: during disable, check subordinate before walking
PCI: Add PCI quirk to disable L0s ASPM state for 82575 and 82598
STag zero is a special STag that allows consumers to access any bus
address without registering memory. The nes driver unfortunately
allows STag zero to be used even with QPs created by unprivileged
userspace consumers, which means that any process with direct verbs
access to the nes device can read and write any memory accessible to
the underlying PCI device (usually any memory in the system). Such
access is usually given for cluster software such as MPI to use, so
this is a local privilege escalation bug on most systems running this
driver.
The driver was using STag zero to receive the last streaming mode
data; to allow STag zero to be disabled for unprivileged QPs, the
driver now registers a special MR for this data.
Cc: <stable@kernel.org>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No software visible difference from revision A.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we disable the Acer WMI backlight device if there is no ACPI
backlight device. As a result, we end up with no backlight device at all.
We should instead disable it if there is an ACPI device, as the other
laptop drivers do. This regression was introduced in febf2d9 ("Acer-WMI:
fingers off backlight if video.ko is serving this functionality").
Each laptop driver with backlight support got a similar change around
febf2d9. The changes to the other drivers look correct; see e.g.
a598c82f for a similar but correct change. The regression is also in
2.6.28.
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Acked-by: Thomas Renninger <trenn@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The s3cmci driver is calling s3c2410_dma_config with incorrect data for
the DCON register. The S3C2410_DCON_HWTRIG is implicit in the channel
configuration and the device selection of S3C2410_DCON_CH0_SDI is
incorrect as the DMA system may not select channel 0.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
W1 master implementations are expected to return 0 or 1 from their
read_bit() function. However, not all platforms do return these values
from gpio_get_value() - namely PXAs won't. Hence the w1 gpio-master needs
to break the result down to 0 or 1 itself.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCIe port driver calls pci_enable_device() during probe but
never calls pci_disable_device() during remove.
Cc: stable@kernel.org
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Prakash's system needs MSI disabled on some bridges, but not all.
This seems to be the minimal fix for 2.6.29, but should be replaced
during 2.6.30.
Signed-off-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
The RPA PCI hotplug driver calls EEH routines, so should depend on
EEH. Also PPC_PSERIES implies PPC64, so remove that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Commit 47a8b0cc (Enable PCIe AER only after checking firmware
support) wants to walk the PCI bus in the remove path to disable
AER, and calls pci_walk_bus for downstream bridges.
Unfortunately, in the remove path, we remove devices and bridges
in a depth-first manner, starting with the furthest downstream
bridge and working our way backwards.
The furthest downstream bridges will not have a dev->subordinate,
and we hit a NULL deref in pci_walk_bus.
Check for dev->subordinate first before attempting to walk the
PCI hierarchy below us.
Acked-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
This patch is intended to disable L0s ASPM link state for 82598 (ixgbe)
parts due to the fact that it is possible to corrupt TX data when coming
back out of L0s on some systems. The workaround had been added for 82575
(igb) previously, but did not use the ASPM api. This quirk uses the ASPM
api to prevent the ASPM subsystem from re-enabling the L0s state.
Instead of adding the fix in igb to the ixgbe driver as well it was
decided to move it into a pci quirk. It is necessary to move the fix out
of the driver and into a pci quirk in order to prevent the issue from
occuring prior to driver load to handle the possibility of the device being
passed to a VM via direct assignment.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
f75375_probe calls i2c_get_clientdata to initialize the data pointer,
but there isn't yet any client data to get, and the value is never
used before the variable is assigned a new value seven lines later.
The call doesn't hurt anything and wastes only a couple of cycles.
The reason to fix it is because this module serves as an example to
hackers writing new hwmon drivers, and this part of the example is
confusing.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver is reporting -128 degrees C as +128 degrees C.
That's not a terribly likely temperature value but let's still
get it right, especially when it simplifies the code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update documentation to prevent further confusion/duplication.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix a logic bug reported by Roel Kluin, by rewriting the error
handling code in a clearer way.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Driver for Dave DNET ethernet controller found on Dave/DENX QongEVB-LITE
FPGA. Heavily based on Dave sources, I've just adopted it to current
kernel version and done some code cleanup.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
radeonfb/aty128fb: Disable broken early resume hook for PowerBooks
hvc_console: Remove tty->low_latency on pseries backends
powerpc: fix linkstation and storcenter compilation breakage
powerpc/4xx: Enable SERIAL_OF support by default for Virtex platforms
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix 945 fence register writes for fence 8 and above.
drm/i915: Protect active fences on i915
drm/i915: Check to see if we've pinned all available fences
drm/i915: Check fence status on every pin.
drm/i915: First recheck for an empty fence register.
drm/i915: Fix bad \n in MTRR failure notice.
drm/i915: Don't restore palettes through VGA registers.
i915: add newline to i915_gem_object_pin failure msg
drm: Return EINVAL on duplicate objects in execbuffer object list
The last 8 fence registers sit at a different offset, so when we went to set
fence number 8 in the lower offset, we instead set PGETBL_CTL, and the GPU
got all sorts of angry at us.
fd.o bug #20567. Easily reproducible by running glxgears and killing it about
6 times.
Signed-off-by: Eric Anholt <eric@anholt.net>
The i915 also uses the fence registers for GPU access to tiled buffers so
we cannot reallocate one whilst it is on the active list. By performing a
LRU scan of the fenced buffers we also avoid waiting the possibility of
waiting on a pinned, or otherwise unusable, buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
We need to check and report if there are no available fences - or else we
spin endlessly waiting for a buffer to magically unpin itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
As we may steal the fence register of an unpinned buffer for another,
every time we repin the buffer we need to recheck whether it needs to be
allocated a fence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
If we wait upon a request and successfully unbind a buffer occupying a
fence register, then that slot will be freed and cause a NULL derefrence
upon rescanning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
radeonfb and aty128fb have a special hook called by the PowerMac platform
code very very early on resume from sleep to bring the screen back. This
is useful for debugging wakup problems, but unfortunately, this also became
a source of problems of its own.
The hook is called extremely early, with interrupts still off, and the code
path involved with that code nowadays rely on things like taking mutexes,
GFP_KERNEL allocations, etc...
In addition, the driver now relies on the PCI core to restore the standard
config space before calling resume which doesn't happen with this early
code path.
I'm keeping the code in but commented out along with a fixup call to
pci_restore_state(). The reason is that I still want to make it easy to
re-enable temporarily to track wake up problems, and it's possible that
I can revive it at some stage if we make sleeping things save to call
in early resume using a system state.
In the meantime, this should fix several reported regressions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The hvcs and hvsi backends both set tty->low_latency to one, along
with more or less scary comments regarding bugs or races that would
happen if not doing so.
However, they also both call tty_flip_buffer_push() in conexts where
it's illegal to do so since some recent tty changes (or at least it
may have been illegal always but it nows blows) when low_latency is
set (ie, hard interrupt or with spinlock held and irqs disabled).
This removes the setting for now to get them back to working condition,
we'll have to address the races described in the comments separately
if they are still an issue (some of this might have been fixed already).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Prevent the kernel from being crashed by a divide-by-zero operation when
supplied an incorrectly filled 'struct fb_var_screeninfo' from userland.
Previously i810_main.c:1005 (i810_check_params) was using the global
'yres' symbol previously defined at i810_main.c:145 as a module parameter
value holder (i810_main.c:2174). If i810fb is compiled-in or if this
param doesn't get a default value, this direct usage leads to a
divide-by-zero at i810_main.c:1005 (i810_check_params). The patch simply
replace the 'yres' global, perhaps undefined symbol usage by a given
parameter structure lookup.
This problem occurs with directfb, mplayer -vo fbdev, SDL library.
It was also reported ( but non solved ) at:
http://mail.directfb.org/pipermail/directfb-dev/2008-March/004050.html
Signed-off-by: Samuel CUELLA <samuel.cuella@supinfo.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit e480814f13 ("[MTD] [MAPS] physmap:
fix wrong free and del_mtd_{partition,device}") introduces a NULL pointer
dereference in physmap_flash_remove when called from the error path in
physmap_flash_probe (if map_probe failed).
Call del_mtd_{partition,device} only if info->cmtd was not NULL.
Reported-by: pHilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
