On some Apple machines the HT MSI mappings are not enabled by firmware, so
we need to do it by hand.
We can't use the pci routines as this code runs too early.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds mpic to the system devices and implements suspend
and resume for them. This is necessary to get interrupts for
modules back to where they were before a suspend to disk.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The weird TSI 10x MPIC needs an EOI after getting a spurious vector. This
patch uses the existing MPIC_SPV_EOI flag to fix this issue.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename MPIC_BROKEN_U3 to something a little more descriptive. Its
effect is to enable support for HT irqs behind the PCI-X/HT bridge on
U3/U4 (aka. CPC9x5) parts.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch changes the MPIC IPIs to be per-CPU to avoid getting a
warning ("Cannot set affinity for irq 251") when taking a CPU
offline via sysfs or during suspend.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move a couple of MPIC smp routines into mpic.c, they're inside an SMP
block in mpic.c - so they're still only built for SMP.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow more than the default 256 MPIC sources. Allocates a new flag
(MPIC_LARGE_VECTORS) to be used by platform code when instantiating
the mpic.
I picked 11 bits worth right now since it would cover the number of
sources on any hardware I have seen. It can always be increased later
if needed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
No need for ?: because of_node_get() can handle NULL argument.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only compare the exact HT capability bits against HT_CAPTYPE_IRQ,
this is a little paranoid, but doesn't hurt.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch applies on top of the MPIC DCR support. It makes the MPIC
driver capable of a lot more auto-configuration based on the device-tree,
for example, it can retreive it's own physical address if not passed as
an argument, find out if it's DCR or MMIO mapped, and set the BIG_ENDIAN
flag automatically in the presence of a "big-endian" property in the
device-tree node.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch implements support for DCR based MPIC implementations. Such
implementations have the MPIC_USES_DCR flag set and don't use the phys_addr
argument of mpic_alloc (they require a valid dcr mapping in the device node)
This version of the patch can use a little bif of cleanup still (I can
probably consolidate rb->dbase/doff, at least once I'm sure on how the
hardware is actually supposed to work vs. possible simulator issues) and
it should be possible to build a DCR-only version of the driver. I need
to cleanup a bit the CONFIG_* handling for that and probably introduce
CONFIG_MPIC_MMIO and CONFIG_MPIC_DCR.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove struct pt_regs * from all handlers.
Also remove the regs argument from get_irq() functions.
Compile tested with arch/powerpc/config/* and
arch/ppc/configs/prep_defconfig
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
This adds defines for the hypertransport capability subtypes and starts
using them a little.
[akpm@osdl.org: fix typo]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
0x08 is the HT capability, while PCI_CAP_ID_HT_IRQCONF would be
the subtype 0x80 that mpic_scan_ht_pic() uses.
Rename PCI_CAP_ID_HT_IRQCONF into PCI_CAP_ID_HT.
And by the way, use it in the ipath driver instead of defining its
own HT_CAPABILITY_ID.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a new hardware information table for mpic. This enables
the mpic code to deal with mpic controllers with different register
layouts and hardware behaviours.
This introduces CONFIG_MPIC_WEIRD. For boards with non standard mpic
controllers, select CONFIG_MPIC_WEIRD and add its hardware information
in the mpic_infos[] array.
TSI108/109 PIC takes the first index of weird hardware information
table. :) The table can be extended. The Tsi108/109 PIC looks like
standard OpenPIC but, in fact, is different in register mapping and
behavior.
The patch does not affect the behavior of standard mpic. If
CONFIG_MPIC_WEIRD is not defined, the code is essentially identical to
the current code.
[benh@kernel.crashing.org:
This patch is a slightly cleaned up version of Zang Roy's support for
the TSI108 MPIC variant. It also fixes up MPC7448_hpc2 to use the new
version of the type macros and changes the way MPIC is selected in
Kconfig to better match what is done for other system devices.
]
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The quad g5 currently doesn't boot due to two problems. This patch fixes the
first one: Apple new way of doing interrupt specifiers in OF for devices using
the HT APIC isn't properly parsed by the new MPIC driver code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch slightly reworks the new irq code to fix a small design error. I
removed the passing of the trigger to the map() calls entirely, it was not a
good idea to have one call do two different things. It also fixes a couple of
corner cases.
Mapping a linux virtual irq to a physical irq now does only that. Setting the
trigger is a different action which has a different call.
The main changes are:
- I no longer call host->ops->map() for an already mapped irq, I just return
the virtual number that was already mapped. It was called before to give an
opportunity to change the trigger, but that was causing issues as that could
happen while the interrupt was in use by a device, and because of the
trigger change, map would potentially muck around with things in a racy way.
That was causing much burden on a given's controller implementation of
map() to get it right. This is much simpler now. map() is only called on
the initial mapping of an irq, meaning that you know that this irq is _not_
being used. You can initialize the hardware if you want (though you don't
have to).
- Controllers that can handle different type of triggers (level/edge/etc...)
now implement the standard irq_chip->set_type() call as defined by the
generic code. That means that you can use the standard set_irq_type() to
configure an irq line manually if you wish or (though I don't like that
interface), pass explicit trigger flags to request_irq() as defined by the
generic kernel interfaces. Also, using those interfaces guarantees that
your controller set_type callback is called with the descriptor lock held,
thus providing locking against activity on the same interrupt (including
mask/unmask/etc...) automatically. A result is that, for example, MPIC's
own map() implementation calls irq_set_type(NONE) to configure the hardware
to the default triggers.
- To allow the above, the irq_map array entry for the new mapped interrupt
is now set before map() callback is called for the controller.
- The irq_create_of_mapping() (also used by irq_of_parse_and_map()) function
for mapping interrupts from the device-tree now also call the separate
set_irq_type(), and only does so if there is a change in the trigger type.
- While I was at it, I changed pci_read_irq_line() (which is the helper I
would expect most archs to use in their pcibios_fixup() to get the PCI
interrupt routing from the device tree) to also handle a fallback when the
DT mapping fails consisting of reading the PCI_INTERRUPT_PIN to know wether
the device has an interrupt at all, and the the PCI_INTERRUPT_LINE to get an
interrupt number from the device. That number is then mapped using the
default controller, and the trigger is set to level low. That default
behaviour works for several platforms that don't have a proper interrupt
tree like Pegasos. If it doesn't work for your platform, then either
provide a proper interrupt tree from the firmware so that fallback isn't
needed, or don't call pci_read_irq_line()
- Add back a bit that got dropped by my main rework patch for properly
clearing pending IPIs on pSeries when using a kexec
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With the new interrupt rework, an interrupt "host" map() callback can be
called after the interrupt is already active.
It's called again for an already mapped interrupt to allow changing the
trigger setup, and currently this is not guarded with a test of wether
the interrupt is requested or not.
I plan to change some of this logic to be a bit less lenient against
random reconfiguring of live interrupts but just not yet.
The ported MPIC driver has a bug where when that happens, it will mask
the interrupt. This changes it to preserve the previous masking of the
interrupt instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the new irq remapper core and removes the old one. Because
there are some fundamental conflicts with the old code, like the value
of NO_IRQ which I'm now setting to 0 (as per discussions with Linus),
etc..., this commit also changes the relevant platform and driver code
over to use the new remapper (so as not to cause difficulties later
in bisecting).
This patch removes the old pre-parsing of the open firmware interrupt
tree along with all the bogus assumptions it made to try to renumber
interrupts according to the platform. This is all to be handled by the
new code now.
For the pSeries XICS interrupt controller, a single remapper host is
created for the whole machine regardless of how many interrupt
presentation and source controllers are found, and it's set to match
any device node that isn't a 8259. That works fine on pSeries and
avoids having to deal with some of the complexities of split source
controllers vs. presentation controllers in the pSeries device trees.
The powerpc i8259 PIC driver now always requests the legacy interrupt
range. It also has the feature of being able to match any device node
(including NULL) if passed no device node as an input. That will help
porting over platforms with broken device-trees like Pegasos who don't
have a proper interrupt tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adapts the generic powerpc interrupt handling code, and all of
the platforms except for the embedded 6xx machines, to use the new
genirq framework.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use the new IRQF_ constants and remove the SA_INTERRUPT define
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidation: remove the irq_affinity[NR_IRQS] array and move it into the
irq_desc[NR_IRQS].affinity field.
[akpm@osdl.org: sparc64 build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[akpm@osdl.org: build fix]
[akpm@osdl.org: another build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Tue, Jun 20, 2006 at 02:01:26PM +1000, Benjamin Herrenschmidt wrote:
> On Mon, 2006-06-19 at 13:08 -0700, Mark A. Greer wrote:
> > MPC10x-style interrupt controllers have a serial mode that allows
> > several interrupts to be clocked in through one INT signal.
> >
> > This patch adds the software support for that mode.
>
> You hard code the clock ratio... why not add a separate call to be
> called after mpic_init,
> something like mpic_set_serial_int(int mpic, int enable, int
> clock_ratio) ?
How's this?
--
MPC10x-style interrupt controllers have a serial mode that allows
several interrupts to be clocked in through one INT signal.
This patch adds the software support for that mode.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
--
arch/powerpc/sysdev/mpic.c | 20 ++++++++++++++++++++
include/asm-powerpc/mpic.h | 10 ++++++++++
2 files changed, 30 insertions(+)
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
Do disable, not enable, the HT APIC IRQ in the function that is
supposed to.
Enable the MPIC IRQ before enabling the downstream APIC IRQ, avoids
potentially losing an interrupt.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental ! There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup the MPIC IO-APIC workarounds, make them a bit more generic,
smaller and faster.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we select ppc32 under the powerpc architecture we get the
error below. This relates to defining distribute_irqs when this
configuratiom option is undefined.
CC arch/powerpc/sysdev/mpic.o
.../arch/powerpc/sysdev/mpic.c: In function `mpic_setup_this_cpu':
.../arch/powerpc/sysdev/mpic.c:788: error: `CONFIG_IRQ_ALL_CPUS'
undeclared (first use in this function)
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Trying to set the priority would just disable the interrupt due to an
incorrect mask used. We rarely use that call, in fact, I think only in
the powermac code for the cmd-power key combo that triggers xmon. So it
got unnoticed for a while.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were computing the wrong address for the MPIC timer registers,
so when we went to initialize them we would have been hitting some
unrelated ioremap... oops.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Having it here rather than in arch/ppc64/kernel/smp.c means that
we can use it on 32-bit SMP systems easily with ARCH=powerpc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the powermac SMP code to use the mpic driver instead of
the openpic driver and fixes the SMP-dependent context switch code.
We had a subtle bug where we were using interrupt numbers 256-259 for
IPIs, but ppc32 had NR_IRQS = 256. Moved the IPIs down to use interrupt
numbers 252-255 instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
