Adding fixed voltage regulators for Vbus and Vbus-boost required
by USB 3.0 DRD controller on Exynos7-espresso board.
Signed-off-by: Vivek Gautam <gautamvivek1987@gmail.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add USB 3.0 DRD controller device node, with its clock
and phy information to enable the same on Exynos7.
Signed-off-by: Vivek Gautam <gautamvivek1987@gmail.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add initial clock configuration for display subsystem for Exynos5433
based TM2/TM2e boards in device tree in order to avoid dependency on the
configuration left by the bootloader. This initial configuration is also
needed to ensure that display subsystem is operational if display power
domain gets turned off before clock controller is probed and the inital
clock configuration left by the bootloader saved.
TM2 and TM2e uses different rate for DISP PLL clock, but for better
maintainability all 'assigned-clocks-*' properties for DISP CMU are
defines in each board dts instead of redefining the rates property.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos5433 LPASS module requires some clocks for proper operation with
power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
LDO7 regulator beside DSI and HDMI provides power for core blocks in Exynos
5433 SoC. Disabling it causes serious current leak - about 200mA.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Ultra HD modes requires clock ticking at increased rate.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As per Exynos7 datasheet FSYS1 pinctrl block does not support drive
strength value of 0x3. This patch fixes this and update the correct
drive strength for sd0_xxx pin definitions.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Common definition for I2S, PMC, SPDIF buses should not define any pull
control for the individual pins. Correct this by changing samsung,pin-pud
property to EXYNOS_PIN_PULL_NONE like it is defined for other Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The "samsung,exynos5433-mipi-video-phy" and "samsung,exynos5250-dwusb3"
DT bindings don't specify a reg property for these nodes, so having a
unit name leads to the following DTC warnings:
Node /soc/video-phy@105c0710 has a unit name, but no reg property
Node /soc/usb@15400000 has a unit name, but no reg property
Node /soc/usb@15a00000 has a unit name, but no reg property
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
HDMI converts RGB/I80 signal from DECON_TV to HDMI/TMDS video stream.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
DECON_TV is 2nd display controller on Exynos5433, used in HDMI path
or 2nd DSI path.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Address should not contain 0x prefix.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Currently TM2E dts includes TM2 but there are some differences
between the two boards and TM2 has some properties that TM2E
doesn't have.
That's why it's important to keep the two dts files independent
and put all the commonalities in a tm2-common.dtsi file.
At the current status the only two differences between the two
dts files (besides the board name) are ldo31 and ldo38.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch fixes wrong values assigned to ldo23 and ldo25 on both TM2 and TM2E.
Fixes: 01e5d23521 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Change the PIN() macro definition so that it can use the macros
from pinctrl/samsung.h header file.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Use the macros defined in include/dt-bindings/pinctrl/samsung.h
instead of hardcoded values.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the bus Device-tree nodes for INT (Internal) block
and enables the bus frequency scaling.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds the AMBA AXI bus nodes using VDD_INT for Exynos5433 SoC.
Following list specify the detailed correlation between sub-block and clock:
- CLK_ACLK_G2D_{400|266} : Bus clock for G2D (2D graphic engine)
- CLK_ACLK_MSCL_400 : Bus clock for MSCL (Memory to memory Scaler)
- CLK_ACLK_GSCL_333 : Bus clock for GSCL (General Scaler)
- CLK_SCLK_JPEG_MSCL : Bus clock for JPEG
- CLK_ACLK_MFC_400 : Bus clock for MFC (Multi Format Codec)
- CLK_ACLK_HEVC_400 : Bus clock for HEVC (High Efficient Video Codec)
- CLK_ACLK_BUS0_400 : NoC's (Network On Chip) bus clock for PERIC/PERIS/FSYS/MSCL
- CLK_ACLK_BUS1_400 : NoC's bus clock for MFC/HEVC/G3D
- CLK_ACLK_BUS2_400 : NoC's bus clock for GSCL/DISP/G2D/CAM0/CAM1/ISP
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds PPMU (Platform Performance Monitoring Unit) Device-tree node
to measure the utilization of each IP in Exynos SoC.
- PPMU_D{0|1}_CPU are used to measure the utilization of MIF (Memory Interface)
block with VDD_MIF power source.
- PPMU_D{0|1}_GENERAL are used to measure the utilization of INT(Internal)
block with VDD_INT power source.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ADpU
-----END PGP SIGNATURE-----
Merge tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Mediatek drivers: mtk-mdp and mtk-vcodec
- some additions at the media documentation
- the CEC core and drivers were promoted from staging to mainstream
- some cleanups at the DVB core
- the LIRC serial driver got promoted from staging to mainstream
- added a driver for Renesas R-Car FDP1 driver
- add DVBv5 statistics support to mn88473 driver
- several fixes related to printk continuation lines
- add support for HSV encoding formats
- lots of other cleanups, fixups and driver improvements.
* tag 'media/v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (496 commits)
[media] v4l: tvp5150: Add missing break in set control handler
[media] v4l: tvp5150: Don't inline the tvp5150_selmux() function
[media] v4l: tvp5150: Compile tvp5150_link_setup out if !CONFIG_MEDIA_CONTROLLER
[media] em28xx: don't store usb_device at struct em28xx
[media] em28xx: use usb_interface for dev_foo() calls
[media] em28xx: don't change the device's name
[media] mn88472: fix chip id check on probe
[media] mn88473: fix chip id check on probe
[media] lirc: fix error paths in lirc_cdev_add()
[media] s5p-mfc: Add support for MFC v8 available in Exynos 5433 SoCs
[media] s5p-mfc: Rework clock handling
[media] s5p-mfc: Don't keep clock prepared all the time
[media] s5p-mfc: Kill all IS_ERR_OR_NULL in clocks management code
[media] s5p-mfc: Remove dead conditional code
[media] s5p-mfc: Ensure that clock is disabled before turning power off
[media] s5p-mfc: Remove special clock rate management
[media] s5p-mfc: Use printk_ratelimited for reporting ioctl errors
[media] s5p-mfc: Set DMA_ATTR_ALLOC_SINGLE_PAGES
[media] vivid: Set color_enc on HSV formats
[media] v4l2-tpg: Init hv_enc field with a valid value
...
A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost) fully
supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier LS1043A
with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above
chips, there are only a few consumer devices and boards added
this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral support
for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom, Rockchip, Berlin,
and ZTE.
Conflicts:
- Documentation/devicetree/bindings/arm/shmobile.txt: a
rename/add conflict, keep both modifications and maintain
alphabetical ordering.
- arch/arm64/boot/dts/*/*.dtsi: nodes were added in netdev,
mmc and clk, keep both sides in each case.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=geT0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost)
fully supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier
LS1043A with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above chips,
there are only a few consumer devices and boards added this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral
support for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom,
Rockchip, Berlin, and ZTE"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (168 commits)
arm64: dts: fix build errors from missing dependencies
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM: dts: artpec: add pcie support
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM64: dts: Add support for Meson GXM
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: NS2: Add PCI PHYs
arm64: dts: NS2: enable sdio1
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: tegra: Add NVIDIA P2771 board support
arm64: tegra: Enable PSCI on P3310
arm64: tegra: Add NVIDIA P3310 processor module support
arm64: tegra: Add GPIO controllers on Tegra186
...
Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where things
come together.
We get a DT descriptions for a couple of new SoCs, all of them variants
of other chips we already support, and usually coming with a new
evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers
or industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on
Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it into
products and have served their purpose in the kernel as a template
for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree
Conflicts:
arch/arm/boot/dts/r8a*.dtsi: a node was added
the clk tree, keep both sides and watch out for git
dropping the required '};' at the end of each side.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wJt3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"Lots of changes as usual, so I'm trying to be brief here. Most of the
new hardware support has the respective driver changes merged through
other trees or has had it available for a while, so this is where
things come together.
We get a DT descriptions for a couple of new SoCs, all of them
variants of other chips we already support, and usually coming with a
new evaluation board:
- Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices
- Qualcomm MDM9615 LTE baseband
- NXP imx6ull, the latest and smallest i.MX6 application processor variant
- Renesas RZ/G (r8a7743 and r8a7745) application processors
- Rockchip PX3, a variant of the rk3188 chip used in Android tablets
- Rockchip rk1108 single-core application processor
- ST stm32f746 Cortex-M7 based microcontroller
- TI DRA71x automotive processors
These are commercially available consumer platforms we now support:
- Motorola Droid 4 (xt894) mobile phone
- Rikomagic MK808 Android TV stick based on Rockchips rx3066
- Cloud Engines PogoPlug v3 based on OX820
- Various Broadcom based wireless devices:
- Netgear R8500 router
- Tenda AC9 router
- TP-LINK Archer C9 V1
- Luxul XAP-1510 Access point
- Turris Omnia open hardware router based on Armada 385
And a couple of new boards targeted at developers, makers or
industrial integration:
- Macnica Sodia development platform for Altera socfpga (Cyclone V)
- MicroZed board based on Xilinx Zynq FPGA platforms
- TOPEET itop/elite based on exynos4412
- WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615
- NextThing CHIP Pro gadget
- NanoPi M1 development board
- AM571x-IDK industrial board based on TI AM5718
- i.MX6SX UDOO Neo
- Boundary Devices Nitrogen6_SOM2 (i.MX6)
- Engicam i.CoreM6
- Grinn i.MX6UL liteSOM/liteBoard
- Toradex Colibri iMX6 module
Other changes:
- added peripherals on renesas, davinci, stm32f429, uniphier, sti,
mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm,
mvebu, allwinner, broadcom, exynos, zynq
- Continued fixes for W=1 dtc warnings
- The old STiH415/416 SoC support gets removed, these never made it
into products and have served their purpose in the kernel as a
template for teh newer chips from ST
- The exynos4415 dtsi file is removed as nothing uses it.
- Intel PXA25x can now be booted using devicetree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits)
arm: dts: zynq: Add MicroZed board support
ARM: dts: da850: enable high speed for mmc
ARM: dts: da850: Add node for pullup/pulldown pinconf
ARM: dts: da850: enable memctrl and mstpri nodes per board
ARM: dts: da850-lcdk: Add ethernet0 alias to DT
ARM: dts: artpec: add pcie support
ARM: dts: add support for Turris Omnia
devicetree: Add vendor prefix for CZ.NIC
ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
ARM: dts: berlin2q-marvell-dmp: fix regulators' name
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM: dts: r8a7794: Add device node for PRR
ARM: dts: r8a7793: Add device node for PRR
ARM: dts: r8a7792: Add device node for PRR
ARM: dts: r8a7791: Add device node for PRR
ARM: dts: r8a7790: Add device node for PRR
ARM: dts: r8a7779: Add device node for PRR
ARM: dts: r8a73a4: Add device node for PRR
ARM: dts: sk-rzg1e: add Ether support
ARM: dts: sk-rzg1e: initial device tree
...
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of
the machines that are still normally used with classic board files.
One tegra fix is important for new bootloader versions, but the
bug has been around for a while without anyone noticing.
The other changes are mostly cosmetic.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i2l2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-urgent fixes from Arnd Bergmann:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc, or that just came a little too late given their size.
The zx fixes make the platform finally boot on real hardware, the
davinci and imx31 get the DT support working better for some of the
machines that are still normally used with classic board files. One
tegra fix is important for new bootloader versions, but the bug has
been around for a while without anyone noticing.
The other changes are mostly cosmetic"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
arm64: tegra: Add missing Smaug revision
arm64: tegra: Add VDD_GPU regulator to Jetson TX1
arm64: dts: zte: clean up gic-v3 redistributor properties
arm64: dts: zx: Fix gic GICR property
bus: vexpress-config: fix device reference leak
soc: ti: qmss: fix the case when !SMP
ARM: lpc32xx: drop duplicate header device.h
ARM: ixp4xx: drop duplicate header gpio.h
ARM: socfpga: fix spelling mistake in error message
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: OMAP2+: pm-debug: Use seq_putc() in two functions
ARM: OMAP2+: Remove the omapdss_early_init_of() function
mfd: tps65217: Fix mismatched interrupt number
ARM: zx: Fix error handling
ARM: spear: Fix error handling
ARM: davinci: da850: Fix pwm name matching
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ut0k
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
* patchwork: (496 commits)
[media] v4l: tvp5150: Add missing break in set control handler
[media] v4l: tvp5150: Don't inline the tvp5150_selmux() function
[media] v4l: tvp5150: Compile tvp5150_link_setup out if !CONFIG_MEDIA_CONTROLLER
[media] em28xx: don't store usb_device at struct em28xx
[media] em28xx: use usb_interface for dev_foo() calls
[media] em28xx: don't change the device's name
[media] mn88472: fix chip id check on probe
[media] mn88473: fix chip id check on probe
[media] lirc: fix error paths in lirc_cdev_add()
[media] s5p-mfc: Add support for MFC v8 available in Exynos 5433 SoCs
[media] s5p-mfc: Rework clock handling
[media] s5p-mfc: Don't keep clock prepared all the time
[media] s5p-mfc: Kill all IS_ERR_OR_NULL in clocks management code
[media] s5p-mfc: Remove dead conditional code
[media] s5p-mfc: Ensure that clock is disabled before turning power off
[media] s5p-mfc: Remove special clock rate management
[media] s5p-mfc: Use printk_ratelimited for reporting ioctl errors
[media] s5p-mfc: Set DMA_ATTR_ALLOC_SINGLE_PAGES
[media] vivid: Set color_enc on HSV formats
[media] v4l2-tpg: Init hv_enc field with a valid value
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.10:
API:
- add skcipher walk interface
- add asynchronous compression (acomp) interface
- fix algif_aed AIO handling of zero buffer
Algorithms:
- fix unaligned access in poly1305
- fix DRBG output to large buffers
Drivers:
- add support for iMX6UL to caam
- fix givenc descriptors (used by IPsec) in caam
- accelerated SHA256/SHA512 for ARM64 from OpenSSL
- add SSE CRCT10DIF and CRC32 to ARM/ARM64
- add AEAD support to Chelsio chcr
- add Armada 8K support to omap-rng"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (148 commits)
crypto: testmgr - fix overlap in chunked tests again
crypto: arm/crc32 - accelerated support based on x86 SSE implementation
crypto: arm64/crc32 - accelerated support based on x86 SSE implementation
crypto: arm/crct10dif - port x86 SSE implementation to ARM
crypto: arm64/crct10dif - port x86 SSE implementation to arm64
crypto: testmgr - add/enhance test cases for CRC-T10DIF
crypto: testmgr - avoid overlap in chunked tests
crypto: chcr - checking for IS_ERR() instead of NULL
crypto: caam - check caam_emi_slow instead of re-lookup platform
crypto: algif_aead - fix AIO handling of zero buffer
crypto: aes-ce - Make aes_simd_algs static
crypto: algif_skcipher - set error code when kcalloc fails
crypto: caam - make aamalg_desc a proper module
crypto: caam - pass key buffers with typesafe pointers
crypto: arm64/aes-ce-ccm - Fix AEAD decryption length
MAINTAINERS: add crypto headers to crypto entry
crypt: doc - remove misleading mention of async API
crypto: doc - fix header file name
crypto: api - fix comment typo
crypto: skcipher - Add separate walker for AEAD decryption
..
Here's the big set of USB/PHY patches for 4.10-rc1.
A number of new drivers are here in this set of changes. We have a new
USB controller type "mtu3", a new usb-serial driver, and the usual churn
in the gadget subsystem and the xhci host controller driver, along with
a few other new small drivers added. And lots of little other changes
all over the USB and PHY driver tree. Full details are in the shortlog
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAxRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynuLgCgsHgM/oba6UaVm1kmyN9V5e3PVjEAn34tRLht
R4enLi8Yv1bOWPdlrpzN
=3MGJ
-----END PGP SIGNATURE-----
Merge tag 'usb-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here's the big set of USB/PHY patches for 4.10-rc1.
A number of new drivers are here in this set of changes. We have a new
USB controller type "mtu3", a new usb-serial driver, and the usual
churn in the gadget subsystem and the xhci host controller driver,
along with a few other new small drivers added. And lots of little
other changes all over the USB and PHY driver tree. Full details are
in the shortlog
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (309 commits)
USB: serial: option: add dlink dwm-158
USB: serial: option: add support for Telit LE922A PIDs 0x1040, 0x1041
USB: OHCI: nxp: fix code warnings
USB: OHCI: nxp: remove useless extern declaration
USB: OHCI: at91: remove useless extern declaration
usb: misc: rio500: fix result type for error message
usb: mtu3: fix U3 port link issue
usb: mtu3: enable auto switch from U3 to U2
usbip: fix warning in vhci_hcd_probe/lockdep_init_map
usb: core: usbport: Use proper LED API to fix potential crash
usbip: add missing compile time generated files to .gitignore
usb: hcd.h: construct hub class request constants from simpler constants
USB: OHCI: ohci-pxa27x: remove useless functions
USB: OHCI: omap: remove useless extern declaration
USB: OHCI: ohci-omap: remove useless functions
USB: OHCI: ohci-s3c2410: remove useless functions
USB: cdc-acm: add device id for GW Instek AFG-125
fsl/usb: Workarourd for USB erratum-A005697
usb: hub: Wait for connection to be reestablished after port reset
usbip: vudc: Refactor init_vudc_hw() to be more obvious
...
framework. The only patch that can even be considered "core" adds another
clk_get() variant. The rest of the changes are in drivers for various SoCs, and
we have a few bits for ARM shmobile architecture code (dts and mach) due to the
dependency we're breaking between shmobile architecture code and its clk
driver. Those shmobile bits have also been pulled into arm-soc tree. Here's the
summary:
Core:
- Support for devm_get_clk_from_child() used with DT bindings that have
subnodes with the 'clocks' property
New Drivers:
- Allwinner A64 (sun50i)
- i.MX imx6ull
- Socionext's UniPhier SoC CPUs
- Mediatek MT2701 SoCs
- Rockchip rk1108 SoCs
- Qualcomm MSM8994/MSM8992 SoCS
- Qualcomm RPM Clocks
- Hisilicon Hi3516CV300 and Hi3798CV200 CRG
- Oxford Semiconductor OX820 and OX810SE SoCs
- Renesas RZ/G1M and RZ/GIE SoCs
- Renesas R-Car RST driver for mode pin states
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver
- Rockchip rk3399,rk3066 PLL optimizations
- i.MX LVDS display glitch fixes and AV PLL precision improvements
- Qualcomm MSM8996 GPU GDSCs, hw controlled GDSCs, and Alpha PLL support
- Explicit demodularization of always builtin drivers
- Freescale Qoriq ls1012a and ls1046a support
- Exynos 5433 parent typo fix and critical clock tagging
- Renesas r8a7743/r8a7745 CPG
- Renesas R-Car M3-W CSI2/VIN/SYS-DMAC/(H)SCIF/I2C/DRIF/gfx support
- stm32f4* LSI, LSE, RTC, and QSPI clocks
- pxa27x and pxa25x cpufreq as clks
- TI omap36xx sprz319 advisory 2.1 workaround
- Broadcom bcm2835 rate change propogation to PLLH_AUX from VEC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=RXZr
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This is a fairly quiet release. We don't have any patches to the core
framework. The only patch that can even be considered "core" adds
another clk_get() variant. The rest of the changes are in drivers for
various SoCs, and we have a few bits for ARM shmobile architecture
code (dts and mach) due to the dependency we're breaking between
shmobile architecture code and its clk driver. Those shmobile bits
have also been pulled into arm-soc tree. Here's the summary:
Core:
- Support for devm_get_clk_from_child() used with DT bindings that
have subnodes with the 'clocks' property
New Drivers:
- Allwinner A64 (sun50i)
- i.MX imx6ull
- Socionext's UniPhier SoC CPUs
- Mediatek MT2701 SoCs
- Rockchip rk1108 SoCs
- Qualcomm MSM8994/MSM8992 SoCS
- Qualcomm RPM Clocks
- Hisilicon Hi3516CV300 and Hi3798CV200 CRG
- Oxford Semiconductor OX820 and OX810SE SoCs
- Renesas RZ/G1M and RZ/GIE SoCs
- Renesas R-Car RST driver for mode pin states
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver
- Rockchip rk3399,rk3066 PLL optimizations
- i.MX LVDS display glitch fixes and AV PLL precision improvements
- Qualcomm MSM8996 GPU GDSCs, hw controlled GDSCs, and Alpha PLL
support
- Explicit demodularization of always builtin drivers
- Freescale Qoriq ls1012a and ls1046a support
- Exynos 5433 parent typo fix and critical clock tagging
- Renesas r8a7743/r8a7745 CPG
- Renesas R-Car M3-W CSI2/VIN/SYS-DMAC/(H)SCIF/I2C/DRIF/gfx support
- stm32f4* LSI, LSE, RTC, and QSPI clocks
- pxa27x and pxa25x cpufreq as clks
- TI omap36xx sprz319 advisory 2.1 workaround
- Broadcom bcm2835 rate change propogation to PLLH_AUX from VEC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
clk: bcm: Fix 'maybe-uninitialized' warning in bcm2835_clock_choose_div_and_prate()
clk: add devm_get_clk_from_child() API
clk: st: clk-flexgen: Unmap region obtained by of_iomap
clk: keystone: pll: Unmap region obtained by of_iomap
clk:mmp:clk-of-mmp2: Free memory and Unmap region obtained by kzalloc and of_iomap
clk:mmp:clk-of-pxa910: Free memory and Unmap region obtained by kzmalloc and of_iomap
clk: mmp: clk-of-pxa1928: Free memory obtained by kzalloc
clk: cdce925: Fix limit check
clk: bcm: Make COMMON_CLK_IPROC into a library
clk: qoriq: added ls1012a clock configuration
clk: ti: dra7: fix "failed to lookup clock node gmac_gmii_ref_clk_div" boot message
clk: bcm: Allow rate change propagation to PLLH_AUX on VEC clock
clk: bcm: Support rate change propagation on bcm2835 clocks
clk: bcm2835: Avoid overwriting the div info when disabling a pll_div clk
clk: ti: omap36xx: Work around sprz319 advisory 2.1
clk: clk-wm831x: fix a logic error
clk: uniphier: add cpufreq data for LD11, LD20 SoCs
clk: uniphier: add CPU-gear change (cpufreq) support
clk: qcom: Put venus core0/1 gdscs to hw control mode
clk: qcom: gdsc: Add support for gdscs with HW control
...
mmc host drivers, some existing drivers being extended to support new IP
versions and lots of other updates.
MMC core:
- Delete eMMC packed command support
- Introduce mmc_abort_tuning() to enable eMMC tuning to fail gracefully
- Introduce mmc_can_retune() to see if a host can be retuned
- Re-work and improve the sequence when sending a CMD6 for mmc
- Enable CDM13 polling when switching to HS and HS DDR mode for mmc
- Relax checking for CMD6 errors after switch to HS200
- Re-factoring the code dealing with the mmc block queue
- Recognize whether the eMMC card supports CMDQ
- Fix 4K native sector check
- Don't power off the card when starting the host
- Increase MMC_IOC_MAX_BYTES to support bigger firmware binaries
- Improve error handling and drop meaningless BUG_ONs()
- Lots of clean-ups and changes to improve the quality of the code
MMC host:
- sdhci: Fix tuning sequence and clean-up the related code
- sdhci: Add support to via DT override broken SDHCI cap register bits
- sdhci-cadence: Add new driver for Cadence SD4HC SDHCI variant
- sdhci-msm: Update clock management
- sdhci-msm: Add support for eMMC HS400 mode
- sdhci-msm: Deploy runtime/system PM support
- sdhci-iproc: Extend driver support to newer IP versions
- sdhci-pci: Add support for Intel GLK
- sdhci-pci: Add support for Intel NI byt sdio
- sdhci-acpi: Add support for 80860F14 UID 2 SDIO bus
- sdhci: Lots of various small improvements and clean-ups
- tmio: Add support for tuning
- sh_mobile_sdhi: Add support for tuning
- sh_mobile_sdhi: Extend driver to support SDHI IP on R7S72100 SoC
- sh_mobile_sdhi: remove support for sh7372
- davinci: Use mmc_of_parse() to enable generic mmc DT bindings
- meson: Add new driver to support GX platforms
- dw_mmc: Deploy generic runtime/system PM support
- dw_mmc: Lots of various small improvements
As a part of the mmc changes this time, I have also pulled in an immutable
branch/tag (soc-device-match-tag1) hosted by Geert Uytterhoeven, to share the
implementation of the new soc_device_match() interface. This is needed by the
below mmc related changes:
- mmc: sdhci-of-esdhc: Get correct IP version for T4240-R1.0-R2.0
- soc: fsl: add GUTS driver for QorIQ platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wGE2
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"It's been an busy period for mmc. Quite some changes in the mmc core,
two new mmc host drivers, some existing drivers being extended to
support new IP versions and lots of other updates.
MMC core:
- Delete eMMC packed command support
- Introduce mmc_abort_tuning() to enable eMMC tuning to fail
gracefully
- Introduce mmc_can_retune() to see if a host can be retuned
- Re-work and improve the sequence when sending a CMD6 for mmc
- Enable CDM13 polling when switching to HS and HS DDR mode for mmc
- Relax checking for CMD6 errors after switch to HS200
- Re-factoring the code dealing with the mmc block queue
- Recognize whether the eMMC card supports CMDQ
- Fix 4K native sector check
- Don't power off the card when starting the host
- Increase MMC_IOC_MAX_BYTES to support bigger firmware binaries
- Improve error handling and drop meaningless BUG_ONs()
- Lots of clean-ups and changes to improve the quality of the code
MMC host:
- sdhci: Fix tuning sequence and clean-up the related code
- sdhci: Add support to via DT override broken SDHCI cap register
bits
- sdhci-cadence: Add new driver for Cadence SD4HC SDHCI variant
- sdhci-msm: Update clock management
- sdhci-msm: Add support for eMMC HS400 mode
- sdhci-msm: Deploy runtime/system PM support
- sdhci-iproc: Extend driver support to newer IP versions
- sdhci-pci: Add support for Intel GLK
- sdhci-pci: Add support for Intel NI byt sdio
- sdhci-acpi: Add support for 80860F14 UID 2 SDIO bus
- sdhci: Lots of various small improvements and clean-ups
- tmio: Add support for tuning
- sh_mobile_sdhi: Add support for tuning
- sh_mobile_sdhi: Extend driver to support SDHI IP on R7S72100 SoC
- sh_mobile_sdhi: remove support for sh7372
- davinci: Use mmc_of_parse() to enable generic mmc DT bindings
- meson: Add new driver to support GX platforms
- dw_mmc: Deploy generic runtime/system PM support
- dw_mmc: Lots of various small improvements
As a part of the mmc changes this time, I have also pulled in an
immutable branch/tag (soc-device-match-tag1) hosted by Geert
Uytterhoeven, to share the implementation of the new
soc_device_match() interface. This is needed by these mmc related
changes:
- mmc: sdhci-of-esdhc: Get correct IP version for T4240-R1.0-R2.0
- soc: fsl: add GUTS driver for QorIQ platforms"
* tag 'mmc-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (136 commits)
mmc: sdhci-cadence: add Cadence SD4HC support
mmc: sdhci: export sdhci_execute_tuning()
mmc: sdhci: Tidy tuning loop
mmc: sdhci: Simplify tuning block size logic
mmc: sdhci: Factor out tuning helper functions
mmc: sdhci: Use mmc_abort_tuning()
mmc: mmc: Introduce mmc_abort_tuning()
mmc: sdhci: Always allow tuning to fall back to fixed sampling
mmc: sdhci: Fix tuning reset after exhausting the maximum number of loops
mmc: sdhci: Fix recovery from tuning timeout
Revert "mmc: sdhci: Reset cmd and data circuits after tuning failure"
mmc: mmc: Relax checking for switch errors after HS200 switch
mmc: sdhci-acpi: support 80860F14 UID 2 SDIO bus
mmc: sdhci-of-at91: remove bogus MMC_SDHCI_IO_ACCESSORS select
mmc: sdhci-pci: Use ACPI to get max frequency for Intel NI byt sdio
mmc: sdhci-pci: Add PCI ID for Intel NI byt sdio
mmc: sdhci-s3c: add spin_unlock_irq() before calling clk_round_rate
mmc: dw_mmc: display the clock message only one time when card is polling
mmc: dw_mmc: add the debug message for polling and non-removable
mmc: dw_mmc: check the "present" variable before checking flags
...
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
The "google,smaug-rev2" string is missing from the compatible list of
Smaug's DT. The differences of rev2 are not relevant at our current
level of support and it boots just fine, so add it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the VDD_GPU regulator (a GPIO-enabled PWM regulator) to the Jetson
TX1 board. This addition allows the GPU to be used provided the
bootloader properly enabled the GPU node.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
[as pointed out by Thierry on IRC, nobody has reported a bug
in the field, but using a new bootloader with a .dtb that
has the incorrect data, it will crash on boot]
Fixes: 336f79c7b6 ("arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support")
Cc: stable@vger.kernel.org #v4.5+
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The gic-v3 property redistributor-stride is only meant as a workaround
for broken platforms that have a redistributor stride deviating what the
architecture defines, i.e. 128KiB for GICv3, 256KiB for GICv4. This is
not the case for ZX296718, and redistributor-stride is not really
necessary. Let's drop it.
Also, #redistributor-regions is only required when there is more than
one such region is present. Let's remove it as well.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
GICR for multiple CPU can be described with start address and stride,
or with multiple address. Current multiple address and stride are
both used. Fix it.
vmalloc patch 727a7f5a9 triggered this bug:
[ 0.097146] Unable to handle kernel paging request at virtual address ffff000008060008
[ 0.097150] pgd = ffff000008602000
[ 0.097160] [ffff000008060008] *pgd=000000007fffe003, *pud=000000007fffd003, *pmd=000000007fffc003, *pte=0000000000000000
[ 0.097165] Internal error: Oops: 96000007 [#1] PREEMPT SMP
[ 0.097170] Modules linked in:
[ 0.097177] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.8.0+ #1474
[ 0.097179] Hardware name: ZTE zx296718 evaluation board (DT)
[ 0.097183] task: ffff80003e8c8b80 task.stack: ffff80003e8d0000
[ 0.097197] PC is at gic_populate_rdist+0x74/0x15c
[ 0.097202] LR is at gic_starting_cpu+0xc/0x20
[ 0.097206] pc : [<ffff0000082b1b18>] lr : [<ffff0000082b26e0>] pstate: 600001c5
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable the x4 PCIe and M.2 Key E slots on Jetson TX1. The Key E slot is
currently untested due to lack of hardware.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Add the PCIe host bridge found on Tegra X1. It implements two root ports
that support x4 and x1 configurations, respectively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add neta nodes for network support both in device tree for the SoC and
the board.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The core and the cluster sleep state entry latencies can't be same as
cluster sleep involves more work compared to core level e.g. shared
cache maintenance.
Experiments have shown on an average about 100us more latency for the
cluster sleep state compared to the core level sleep. This patch fixes
the entry latency for the cluster sleep state.
Fixes: 28e10a8f3a ("arm64: dts: juno: Add idle-states to device tree")
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Jon Medhurst (Tixy)" <tixy@linaro.org>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PCIe root complex on Juno translates the MMIO mapped
at 0x5f800000 to the PIO address range starting at 0
(which is common because PIO addresses are generally < 64k).
Correct the DT to reflect this.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- new SoC support: S912/GXM series (8x A53)
- new boards: Nexbox A1 (S912), Nexbox A95X (S905X)
- resets for 2nd USB PHY
- update SCPI compatible for pre-v1.0 devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=kgDs
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt64
Pull "Amlogic 64-bit DT updates for v4.10, round 2" from Kevin Hilman:
- new SoC support: S912/GXM series (8x A53)
- new boards: Nexbox A1 (S912), Nexbox A95X (S905X)
- resets for 2nd USB PHY
- update SCPI compatible for pre-v1.0 devices
* tag 'amlogic-dt64-2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM64: dts: Add support for Meson GXM
ARM64: dts: meson-gxbb: add the USB reset also to the second USB PHY
Add clock controller device nodes, including one top clock controller,
two low speed clock controllers and one audio clock controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYPDsqAAoJEFBXWFqHsHzOl5cH/iifyZ+RRLVuZBKRFM2TEq6T
0DFYvL+wQFQG74b3W8zT50r9ej5NLDvz7yMoqm2Njd/Qn2zM+WA8vxyhTES3JsqF
PIzbaYMaYfxMesGIfdCDFQ85g4TdKISCqEMiMrgNFynol6Yk3VHzjT7ODYPAzR/k
DZ7tRx1WW7dGLH4EsGZDo1dwC8zbWWoi0J8epbq3qgOXAZ5r5o8TZ4JCIMciqaXc
VaQVx/+3qK5rmW+b5BkPk8lFNHEPfi27m/NeHTebWg0YZ+VzvuoS3tAvJl5f1170
d21LvukXnrquLdj1KaD0LQOKP38oSGFp/1l9QsYfHHKnyIZPk17RNrW0wvRg5Zg=
=+8XT
-----END PGP SIGNATURE-----
Merge tag 'zte-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Pull "ZTE arm64 device tree update for 4.10" from Shawn Guo:
Add clock controller device nodes, including one top clock controller,
two low speed clock controllers and one audio clock controller.
* tag 'zte-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: zx: Add clock controller nodes
- fix some dtc compiler warnings
-----BEGIN PGP SIGNATURE-----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=JqjI
-----END PGP SIGNATURE-----
Merge tag 'berlin64-dt-for-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin into next/dt64
Pull "Berlin64 DT changes for v4.10" from Jisheng Zhang:
- fix some dtc compiler warnings
* tag 'berlin64-dt-for-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
as the binding doc for the 32bit rk1108 eval board to prevent it
from conflicting with the recently added 64bit px5 board.
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYNj30EBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYEoJQf/
WaANx7eR9cLkinPv6H123jeHAtMdvLFHmwb9kr2DwwNs6C9UxIsp9VddpG7XMSpI
bQLES0o0MALAAzIJH1oBb2wOWfDRWB/oXa/bSWXScbRXML+fH9ew1i1FaQQRDPHP
0/nm6GMbRZfMEraZHzTEY9duobLhbBH2va9GBv7M453D65B26c+ECvgbjULkI6My
qAdy5nN4Fb2YhxlZJz+WQQt59MNBT6nw8ObNPgKmSI18vB8BnQxqIEfo1gCuW+Iz
Sz+367EhVDtSW8cMWLttK6wB2iiiYGD0TOYfEeZS1zWavQlqDpFxFgZ66AKXdTxA
OYuAB8AKkTfa8NmejAUR2Q==
=PZ7U
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Pull "Rockchip dts64 changes for 4.10" from Heiko Stübner:
Some more powerdomains and usb2-otg support for the rk3399 as well
as the binding doc for the 32bit rk1108 eval board to prevent it
from conflicting with the recently added 64bit px5 board.
* tag 'v4.10-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: rockchip: add usb2-phy otg-port support for rk3399
arm64: dts: rockchip: add pd_sd power-domain node for rk3399
arm64: dts: rockchip: add eMMC's power domain support for rk3399
arm64: dts: rockchip: add backlight support for rk3399 evb board
arm64: dts: rockchip: add gmac needed pclk for rk3399 pd
* Add SDHC xo clk and 1.8V DDR support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EDYb
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt64
Pull "Qualcomm ARM64 Updates for v4.10 - Part 2" from Andy Gross:
* Add SDHC xo clk and 1.8V DDR support
* tag 'qcom-arm64-for-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
ARM: dts: Add xo to sdhc clock node on qcom platforms
1. Add Performance Monitor Unit to Exynos7.
2. Add MFC, JPEG and Gscaler to Exynos5433 based TM2 board.
3. Cleanups and fixes for recently added TM2 and TM2E boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/AE/
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Pull "Samsung DeviceTree arm64 second update for v4.10" from Krzysztof Kozłowski:
1. Add Performance Monitor Unit to Exynos7.
2. Add MFC, JPEG and Gscaler to Exynos5433 based TM2 board.
3. Cleanups and fixes for recently added TM2 and TM2E boards.
* tag 'samsung-dt64-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: dts: exynos: TM2 - add support for MFC video codec device
arm64: dts: exynos: TM2 - add support for JPEG codec device
arm64: dts: exynos: TM2 - add support for GScaler devices
arm64: dts: exynos: TM2 - remove unused UART3 and set clocks directly on CMU
arm64: dts: exynos: Assign parent clock of the clkout clock for TM2 board
arm64: dts: exynos: Move FSYS CMU configuration from Exynos5433 dtsi to TM2 dts
arm64: dts: exynos: Add missing parent clocks to audio block in Exynos5433 SoC
arm64: dts: exynos: Fix FSYS CMU parent clocks in Exynos5433 SoC
arm64: dts: exynos: Fix IRQ type flags for Exynos5433 SoC
arm64: dts: Add ARM PMU node for exynos7