The HIDP specs define an idle-timeout which automatically disconnects a
device. This has always been implemented in the HIDP layer and forced a
synchronous shutdown of the hidp-scheduler. This works just fine, but
lacks a forced disconnect on the underlying l2cap channels. This has been
broken since:
commit 5205185d46
Author: David Herrmann <dh.herrmann@gmail.com>
Date: Sat Apr 6 20:28:47 2013 +0200
Bluetooth: hidp: remove old session-management
The old session-management always forced an l2cap error on the ctrl/intr
channels when shutting down. The new session-management skips this, as we
don't want to enforce channel policy on the caller. In other words, if
user-space removes an HIDP device, the underlying channels (which are
*owned* and *referenced* by user-space) are still left active. User-space
needs to call shutdown(2) or close(2) to release them.
Unfortunately, this does not work with idle-timeouts. There is no way to
signal user-space that the HIDP layer has been stopped. The API simply
does not support any event-passing except for poll(2). Hence, we restore
old behavior and force EUNATCH on the sockets if the HIDP layer is
disconnected due to idle-timeouts (behavior of explicit disconnects
remains unmodified). User-space can still call
getsockopt(..., SO_ERROR, ...)
..to retrieve the EUNATCH error and clear sk_err. Hence, the channels can
still be re-used (which nobody does so far, though). Therefore, the API
still supports the new behavior, but with this patch it's also compatible
to the old implicit channel shutdown.
Cc: <stable@vger.kernel.org> # 3.10+
Reported-by: Mark Haun <haunma@keteu.org>
Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the diagnostic settings are not persistent over HCI Reset, then this
quirk can be used to tell the Bluetoth core about it. This will ensure
that the settings are programmed correctly when the controller is
powered up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are LE devices on the market that start off by announcing their
public address and then once paired switch to using private address.
To be interoperable with such devices we should simply trust the fact
that we're receiving an IRK from them to indicate that they may use
private addresses in the future. Instead, simply tie the persistency
to the bonding/no-bonding information the same way as for LTKs and
CSRKs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sending diagnostic messages directly to the monitor socket might cause
issues for devices processing their messages in interrupt context. So
instead of trying to directly forward them, queue them up with the other
HCI packets and lets them be processed by the sockets at the same time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using the HCI_CHANNEL_RAW, restrict the packet types to valid ones
from the Bluetooth specification.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI_VENDOR_PKT quirk was needed for BPA-100/105 devices that send
these messages. Now that there is support for proper diagnostic channel
this quirk is no longer needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes sure that conn_params that were created just for
explicit_connect, will get properly deleted during cleanup.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After clearing the params->explicit_connect variable the parameters
may need to be either added back to the right list or potentially left
absent from both the le_reports and the le_conns lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Devices undergoing an explicit connect should not have their
conn_params struct removed by the mgmt Remove Device command. This
patch fixes the necessary checks in the command handler to correct the
behavior.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We can't use hci_explicit_connect_lookup() since that would only cover
explicit connections, leaving normal reconnections completely
untouched. Not using it in turn means leaving out entries in
pend_le_reports.
To fix this and simplify the logic move conn params from the reports
list to the pend_le_conns list for the duration of an explicit
connect. Once the connect is complete move the params back to the
pend_le_reports list. This also means that the explicit connect lookup
function only needs to look into the pend_le_conns list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The code should never directly call hci_conn_hash_del since many
cleanup & reference counting updates would be lost. Normally
hci_conn_del is the right thing to do, but in the case of a connection
doing LE scanning this could cause a deadlock due to doing a
cancel_delayed_work_sync() on the same work callback that we were
called from.
Connections in the LE scanning state actually need very little cleanup
- just a small subset of hci_conn_del. To solve the issue, refactor
out these essential pieces into a new hci_conn_cleanup() function and
call that from the two necessary places.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When disable/enable scan command is issued twice, some controllers
will return an error for the second request, i.e. requests with this
command will fail on some controllers, and succeed on others.
This patch makes sure that unnecessary scan disable/enable commands
are not issued.
When adding device to the auto connect whitelist when there is pending
connect attempt, there is no need to update scan.
hci_connect_le_scan_cleanup is conditionally executing
hci_conn_params_del, that is calling hci_update_background_scan. Make
the other case also update scan, and remove reduntand call from
hci_connect_le_scan_remove.
When stopping interleaved discovery the state should be set to stopped
only when both LE scanning and discovery has stopped.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-10-08
Here's another set of Bluetooth & 802.15.4 patches for the 4.4 kernel.
802.15.4:
- Many improvements & fixes to the mrf24j40 driver
- Fixes and cleanups to nl802154, mac802154 & ieee802154 code
Bluetooth:
- New chipset support in btmrvl driver
- Fixes & cleanups to btbcm, btmrvl, bpa10x & btintel drivers
- Support for vendor specific diagnostic data through common API
- Cleanups to the 6lowpan code
- New events & message types for monitor channel
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the controller is unconfigured (for example it does not have a
valid Bluetooth address), then the basic debugfs entries for dut_mode
and vendor_diag are not creates. Ensure they are created in __hci_init
and also __hci_unconf_init functions. One of them is called during setup
stage of a new controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch moves values for all lowpan interface to the shared
implementation of 6lowpan. This patch also quietly fixes the forgotten
IFF_NO_QUEUE flag for the bluetooth 6LoWPAN interface. An identically
commit is 4afbc0d ("net: 6lowpan: convert to using IFF_NO_QUEUE") which
wasn't changed for bluetooth 6lowpan.
All 6lowpan interfaces should be virtual with IFF_NO_QUEUE, using EUI64
address length, the mtu size is 1280 (IPV6_MIN_MTU) and the netdev type
is ARPHRD_6LOWPAN.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The chan_get() function just adds unnecessary indirection to calling
the chan_create() call. The only added value it gives is the chan->ops
assignment, but that can equally well be done in the calling code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The typical convention when having both a child and a parent channel
variable is to call the former 'chan' and the latter 'pchan'. When
there's only one variable it's called chan. Rename the 'pchan'
variables in the 6lowpan code to follow this convention.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All the chan_open() function now does is to call chan_create() so it
doesn't really add any value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The L2CAP core code makes sure of setting the channel state to
BT_CONNECTED, so there's no need for the implementation code (6lowpan
in this case) to do it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The L2CAP core code already sets the local MPS to a sane value. The
remote MPS value otoh comes from the remote side so there's no point
in trying to hard-code it to any value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The omtu value is determined by the remote peer so there's no point in
trying to hard-code it to any value. The IPSP specification otoh gives
a more reasonable value for the imtu, i.e. 1280.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When calling the hci_recv_frame driver function check for valid packet
types that the core should process. This should catch issues with
drivers trying to feed vendor packet types through this interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller requires the HCI Reset command to be send when
closing the transport, the HCI_AUTO_OFF needs to be accounted for. The
current code tries to actually do that, but the flag gets cleared to
early. So store its value and use it that stored value instead of
checking for a flag that is always cleared.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a new debugfs entry for enabling and disabling the vendor
diagnostic mode. It is only exposed for drivers that provide the
set_diag driver callback and actually have an option for vendor
specific diagnostic information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Introduce hci_recv_diag function for HCI drivers to allow sending vendor
specific diagnostic messages into the Bluetooth core stack. The messages
are not processed, but they are forwarded to the monitor channel and can
be retrieved by user space diagnostic tools.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth public device address might change during controller setup
and it makes it a lot simpler for monitoring tools if they just get told
what the new address is. In addition include the manufacturer / company
information of the controller. That allows for easy vendor specific HCI
command and event handling.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the core starts or shuts down the actual HCI transport, send a new
monitor event that indicates that this is happening. These new events
correspond to HCI_DEV_OPEN and HCI_DEV_CLOSE events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Setting and clearing of HCI_RUNNING flag in each and every driver is
just duplicating the same code all over the place. So instead of having
the driver do it in their hdev->open and hdev->close callbacks, set it
globally in the core transport handling.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In all callbacks for hdev->send the status of HCI_RUNNING is checked. So
instead of repeating that code in every driver, move the check into the
hci_send_frame function before calling hdev->send.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When opening the HCI transport via hdev->open send HCI_DEV_OPEN event
and when closing the HCI transport via hdev->close send HCI_DEV_CLOSE.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The stack internal events that are exposed to userspace should be
limited to HCI_DEV_REG, HCI_DEV_UNREG, HCI_DEV_UP and HCI_DEV_DOWN.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Send a HCI command and wait for command complete event.
This function serializes the requests by grabbing the req_lock.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ratelimited version of the BT_ERR macro.
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With 9380f9eacf the order of unsetting
the HCI_USER_CHANNEL flag of the HCI device was reverted to ensure
the device is first closed before making it available again.
Due to hci_dev_close checking for HCI_USER_CHANNEL being set on the
device it was never really closed and was kept opened. We're now
calling hci_dev_do_close directly to make sure the device is correctly
closed and we keep the correct order to unset the flag on our device
object.
Signed-off-by: Simon Fels <simon.fels@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some counterfeit CSR controllers also have broken behavior with the
HCI_Read_Stored_Link_Key command:
< HCI Command: Read Stored Link Key (0x03|0x000d) plen 7
Address: 00:00:00:00:00:00 (OUI 00-00-00)
Read all: 0x01
> HCI Event: Command Complete (0x0e) plen 8
Read Stored Link Key (0x03|0x000d) ncmd 1
Status: Unsupported Feature or Parameter Value (0x11)
Max num keys: 0
Num keys: 0
Extend the existing HCI_QUIRK_BROKEN_STORED_LINK_KEY to be also used
for this HCI command.
Reported-and-tested-by: Rhobison Alves Pereira <rhobison@hotmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are several actions that smp_conn_security() might make that do
not require a valid SMP context (conn->smp pointer). One of these
actions is to encrypt the link with an existing LTK. If the SMP
context wasn't initialized properly we should still allow the
independent actions to be done, i.e. the check for the context should
only be done at the last possible moment.
Reported-by: Chuck Ebbert <cebbert.lkml@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.0+
This makes the function sco_conn_del have a return type of void now
due to this function always running successfully and thus never
needing to signal its caller when a non recoverable internal failure
occurs by returning a error code to its respective caller.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-08-16
Here's what's likely the last bluetooth-next pull request for 4.3:
- 6lowpan/802.15.4 refactoring, cleanups & fixes
- Document 6lowpan netdev usage in Documentation/networking/6lowpan.txt
- Support for UART based QCA Bluetooth controllers
- Power management support for Broeadcom Bluetooth controllers
- Change LE connection initiation to always use passive scanning first
- Support for new Silicon Wave USB ID
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduced the 6lowpan netdev private data struct. We name it
lowpan_priv and it's placed at the beginning of netdev private data. All
lowpan interfaces should allocate this room at first of netdev private
data. 6LoWPAN LL private data can be allocate by additional netdev private
data, e.g. dev->priv_size should be "sizeof(struct lowpan_priv) +
sizeof(LL_LOWPAN_PRIVATE_DATA)".
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The usually way to get the btle lowpan private data is to use the
introduced lowpan_dev inline function. This patch will cleanup by using
lowpan_dev consequently.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.
This patch enables new connection establishment procedure. Instead of just
sending HCI_OP_LE_CREATE_CONN to controller, "connect" will add device to
kernel whitelist and start scan. If advertisement is received, it'll be
compared against whitelist and then trigger connection if it matches.
That fixes mentioned reconnect issue for already paired devices. It also
make whole connection procedure more robust. We can try to connect to
multiple devices at same time now, even though controller allow only one.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.
This patch makes sure that when new procedure is in use, and we're stuck
in scan phase because no advertisement was received and timeout happened,
or app decided to close socket, scan whitelist gets properly cleaned up.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, when trying to connect to already paired device that just
rotated its RPA MAC address, old address would be used and connection
would fail. In order to fix that, kernel must scan and receive
advertisement with fresh RPA before connecting.
This path makes sure that after advertisement is received from device that
we try to connect to, it is properly handled in check_pending_le_conn and
trigger connect attempt.
It also modifies hci_le_connect to make sure that connect attempt will be
properly continued.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
