Add the PCI_SUBSYS_DEVID_81XX_RGX and use the same to set
the max bgx per node count.
This fixes the issue intoduced by following commit
78aacb6f6 net: thunderx: Fix invalid mac addresses for node1 interfaces
With this commit the max_bgx_per_node for 81xx is set as 2 instead of 3
because of which num_vfs is always calculated as zero.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove deprecated pci_enable_msix API in favour of its
successor pci_alloc_irq_vectors.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for TSO and checksum hardware offloads for ipv6.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not consider IPv6 frames with zero UDP checksum as frames
with bad checksum and drop them.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When booted with ACPI, random mac addresses are being
assigned to node1 interfaces due to mismatch of bgx_id
in BGX driver and ACPI tables.
This patch fixes this issue by setting maximum BGX devices
per node based on platform/soc instead of a macro. This
change will set the bgx_id appropriately.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When BGX/LMACs are in QSGMII mode, for some LMACs, mode info is
not being printed. This patch will fix that. With changes already
done to not do any sort of serdes 2 lane mapping config calculation
in kernel driver, we can get rid of this logic.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ACPI support has been added to ARM IOMMU driver in 4.10 kernel
and that has resulted in VNIC interfaces throwing translation
faults when kernel is booted with ACPI as driver was not using
DMA API. This patch fixes the issue by using DMA API which inturn
will create translation tables when IOMMU is enabled.
Also VNIC doesn't have a seperate receive buffer ring per receive
queue, so there is no 1:1 descriptor index matching between CQE_RX
and the index in buffer ring from where a buffer has been used for
DMA'ing. Unlike other NICs, here it's not possible to maintain dma
address to virt address mappings within the driver. This leaves us
no other choice but to use IOMMU's IOVA address conversion API to
get buffer's virtual address which can be given to network stack
for processing.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the case where there is no phydev attached
to a LMAC in DT due to non-existance of a PHY driver or due
to usage of non-stanadard PHY which doesn't support autoneg.
Changes dependeds on firmware to send correct info w.r.t
PHY and autoneg capability.
This patch also covers a case where a 10G/40G interface is used
as a 1G with convertors with Cortina PHY in between.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following smatch and coccinelle warnings:
drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119 xcv_setup_link() error: we previously assumed 'xcv' could be null (see line 118) [smatch]
drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119:16-20: ERROR: xcv is NULL but dereferenced. [coccinelle]
Fixes: 6465859aba ("net: thunderx: Add RGMII interface type support")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DLMs and SLMs on 80/81/83xx, many lane configurations
across different boards are coming up. Also kernel doesn't have
any way to identify board type/info and since firmware does,
just get rid of figuring out lane to serdes config and take
whatever has been programmed by low level firmware.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support to set Rx/Tx queue sizes from ethtool. Fixes
an issue with retrieving queue size. Also sets SQ's CQ_LIMIT
based on configured Tx queue size such that HW doesn't process
SQEs when there is no sufficient space in CQ.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While probing BGX we requesting appropriate QLM for it's configuration
and get LMAC count by that request. Then, while reading configured
MAC values from SSDT table we need to save them in proper mapping:
BGX[i]->lmac[j].mac = <MAC value>
to later provide for initialization stuff. In order to fill
such mapping properly we need to add lmac index to be used while
acpi initialization since at this moment bgx->lmac_count already contains
actual value.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From struct ethtool_ops:
int (*set_rxfh)(struct net_device *, const u32 *indir,
const u8 *key, const u8 hfunc);
Change function arg of hfunc to const type.
V2: Fixed indentation.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 712c318534 ("net: thunderx: Program LMAC credits based on MTU")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transmit queue timeout issue is seen in two cases
- Due to a race condition btw setting stop_queue at xmit()
and checking for stopped_queue in NAPI poll routine, at times
transmission from a SQ comes to a halt. This is fixed
by using barriers and also added a check for SQ free descriptors,
incase SQ is stopped and there are only CQE_RX i.e no CQE_TX.
- Contrary to an assumption, a HW errata where HW doesn't stop transmission
even though there are not enough CQEs available for a CQE_TX is
not fixed in T88 pass 2.x. This results in a Qset error with
'CQ_WR_FULL' stalling transmission. This is fixed by adjusting
RXQ's RED levels for CQ level such that there is always enough
space left for CQE_TXs.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable pause frames on both Rx and Tx side, configure pause
interval e.t.c. Also support for enable/disable pause frames
on Rx/Tx via ethtool has been added.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables moving average calculation of Rx pkt's resources
and configures RED and backpressure levels for both CQ and RBDR.
Also initialize SQ's CQ_LIMIT properly.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 80xx only one lane of DLM0 and DLM1 (of BGX0) can be used
, so even though lmac count may be 2 but LMAC1 should use
serdes lane of DLM1. Since it's not possible to distinguish
80xx from 81xx as PCI devid are same, this patch adds this
config support by replying on what firmware configures the
lmacs with.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following
1. When interface is being teardown and queues are being cleaned up,
free pending SKBs that are in SQ which are either not transmitted
or freed as NAPI is disabled by that time.
2. While interface initialization, delay CFG_DONE notification till
the end to avoid corner cases where TXQs are enabled but CQ
interrupts are not which results blocking transmission and kicking
off watchdog.
3. Check for IFF_UP while re-enabling RBDR interrupts from tasklet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes multiple issues
1. Convert all driver statistics to percpu counters for accuracy.
2. To avoid multiple CQEs posted by a TSO packet appended to HW,
TSO pkt's SQE has 'post_cqe' not set but a dummy SQE is added
for getting HW transmit completion notification. This dummy
SQE has 'dont_send' set and HW drops the pkt pointed to in this
thus Tx drop counter increases. This patch fixes this by subtracting
SW tx tso counter from HW Tx drop counter for actual packet drop counter.
3. Reset all individual queue's and VNIC HW stats when interface is going down.
4. Getrid off unnecessary counters in hot path.
5. Bringout all CQE error stats i.e both Rx and Tx.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes enabling of HW verification of L3/L4 length and
TCP/UDP checksum which is currently being cleared. Also fixed VLAN
stripping config which is being cleared when multiqset is enabled.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Programming LMAC credits taking 9K frame size by default is incorrect
as for an interface which is one of the many on the same BGX/QLM
no of credits available will be less as Tx FIFO will be divided
across all interfaces. So let's say a BGX with 40G interface and another
BGX with multiple 10G, bandwidth of 10G interfaces will be effected when
traffic is running on both 40G and 10G interfaces simultaneously.
This patch fixes this issue by programming credits based on netdev's MTU.
Also fixed configuring MTU to HW and added CQE counter for pkts which
exceed this value.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the 'bgx_id' determination on 83xx where there are
4 BGX blocks instead of 2 on other platforms.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a regression caused by previous commit
when irq name exceeds 20 byte array if interface's name
size is large.
Fixes: e412621394 ("net: thunderx: Use netdev's name for naming VF's interrupts")
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
On ThunderX 88xx pass 2.x chips when TSO is offloaded to HW,
HW posts a CQE for every TSO segment transmitted. Current code
does handles this, but is prone to issues when segment sizes are
small resulting in SW processing too many CQEs and also at times
frees a SKB which is not yet transmitted.
This patch handles the errata in a different way and eliminates issues
with earlier approach, TSO packet is submitted to HW with post_cqe=0,
so that no CQE is posted upon completion of transmission of TSO packet
but a additional HDR + IMMEDIATE descriptors are added to SQ due to
which a CQE is posted and will have required info to be used while
cleanup in napi. This way only one CQE is posted for a TSO packet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a issue in HW where-in while sending GSO sized pkts
as part of TSO, if pkt len falls below configured min packet
size i.e 60, NIC will zero PAD packet and also updates IP total length.
Hence set this value to lessthan min pkt size of MAC + IP + TCP
headers, BGX will anyway do the padding to transmit 64 byte pkt
including FCS.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool_ops .get_regs function attempts to read the nonexistent
register NIC_QSET_SQ_0_7_CNM_CHG, which produces a "bus error" type
OOPs.
Fix by not attempting to read, and removing the definition of,
NIC_QSET_SQ_0_7_CNM_CHG. A zero is written into the register dump to
keep the layout unchanged.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: <stable@vger.kernel.org> # 4.4.x-
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting BGXX_SPUX_MISC_CONTROL::RX_PACKET_DIS is not needed as
packet reception is anyway disabled by BGXX_CMRX_CONFIG::DATA_PKT_RX_EN.
Also setting RX_PACKET_DIS causes a bogus remote fault condition
which delays link detection.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard API to generate a random RSS hash key
on every boot.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables parsing of inner layers for tunnelled packets.
Signed-off-by: Zyta Szpak <zr@semihalf.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables bulk freeing on the Tx side.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set MAC addresses only for primary VF's and don't for
secondary VFs.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SQ/TXQ is reclaimed i.e reset it's stats also automatically reset
by HW. This is not the case with RQ. Also VF doesn't have write access
to statistics counter registers. Hence a new Mbox msg is introduced which
supports resetting RQ, SQ and full Qset stats. Currently only RQ stats
are being reset using this mbox message.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding debug messages in case of NACK for a mailbox message, also
did small cleanups.
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of a round about way of converting buffers to SKBs and
combining them into a frag list, use standard skb_add_rx_frag()
API to merge page fragments. This code is useful when incoming
packets are of size more than RCV_FRAG_LEN which is currently
set to 2048bytes.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the way VF's irqs are visible in /proc/interrupts.
Instead of VF id, logical interface's netdev name is used for IRQ
naming and also all secondary VF's interrupts in multiqset config
use primary VF's netdev name.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
83xx has 4 BGX blocks and are enabled mixed QLM/DLM
configs. BGX0/BGX1 are from QLM2/QLM3, BGX3 is DLM4
and BGX2 is split across DLM5 & DLM6.
This patch adds support for BGX2's split config and also
enables all 4 BGXs to be used.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
83xx will have 4 BGX blocks i.e 16 LMACs, to avoid changing
the same with every platform, nicpf struct elements which
track LMAC related info are now allocated runtime based
on platform's max possible BGX count.
Also fixed configuring min packet size for all LMAC's
supported on a platform.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RGX/RGMII interface type support to BGX
driver. This type of interface is supported by 81xx SOC.
CN81XX VNIC has 8 VFs and max possible LMAC interfaces are 9,
hence RGMII interface will not work if all DLMs are in BGX mode
and all 8 LMACs are enabled
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for QSGMII interface type to
the BGX driver. This type of interface is supported by
81xx SOC.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for BGX module on 81xx where a BGX
can be split and have different LMACs configured in
different modes.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 88xx all LMACs in a BGX will be in same mode but on 81xx
BGX can be split as two and there can be LMACs configured in
different modes.
These changes move lmac_type, lane2serdes fields into per lmac
struct from BGX struct. Got rid of qlm_mode field which has become
redundant with these changes. And now no of valid LMACs is read
from CSRs configured by low level firmware and figuring out the
same based on QLM mode is discarded
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
88xx has 128 VFs, 81xx has 8 VFs and 83xx will have 32VFs.
Made changes to PF driver such that mailbox interrupt enable
registers are configuired based on number of VFs HW supports.
Also cleanedup mailbox irq handler registration code.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike 88xx, CQE_RX descriptor's tunnelling extension i.e CQE_RX2_S
is always enabled on 81xx/83xx and HW does insert these fields into
CQE_RX. As a result receive buffer addresses will now be present at
7th word of CQE_RX instead of 6th.
Enable CQE_RX2_S on 88xx pass 2.x as well.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
81xx has only 4 CPUs, so it doesn't make sense to initialize
entire Qset i.e 8 queues by default. Made changes to queue
initialization to init queues equal to number of CPUs or
8 queues whichever is lesser. Also this will be applicable to
VMs with VNIC VF attached and having less VCPUs
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds info on HW maximums of 81xx/83xx and also
configures receive and transmit datapaths accordingly.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device IDs of VNIC on newer chips and also
registers VF driver with them. Device id remains same for all
versions of chips but subsystem device id changes.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver has most of the HW maximums info like no of channels,
traffic limiters, RSS indices e.t.c in the form of macros. These have
been moved into a 'hw_info' structure so that support for VNIC on
newer chips with different set of HW maximums can be added.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TL4 calculation for a given SQ of secondary Qsets is incorrect
and goes out of bounds and also for some SQ's TL4 chosen will
transmit data via a different BGX interface and not same as
primary Qset's interface.
This patch fixes this issue.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for SMU RX local/remote faults along with SPU LINK
status. Otherwise at times link is UP at our end but DOWN
at link partner's side. Also due to an issue in BGX it's
rarely seen that initialization doesn't happen properly
and SMU RX reports faults with everything fine at SPU.
This patch tries to reinitialize LMAC to fix it.
Also fixed LMAC disable sequence to properly bring down link.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Tao Wang <tao.wang@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes and more updates from David Miller:
1) Tunneling fixes from Tom Herbert and Alexander Duyck.
2) AF_UNIX updates some struct sock bit fields with the socket lock,
whereas setsockopt() sets overlapping ones with locking. Seperate
out the synchronized vs. the AF_UNIX unsynchronized ones to avoid
corruption. From Andrey Ryabinin.
3) Mount BPF filesystem with mount_nodev rather than mount_ns, from
Eric Biederman.
4) A couple kmemdup conversions, from Muhammad Falak R Wani.
5) BPF verifier fixes from Alexei Starovoitov.
6) Don't let tunneled UDP packets get stuck in socket queues, if
something goes wrong during the encapsulation just drop the packet
rather than signalling an error up the call stack. From Hannes
Frederic Sowa.
7) SKB ref after free in batman-adv, from Florian Westphal.
8) TCP iSCSI, ocfs2, rds, and tipc have to disable BH in it's TCP
callbacks since the TCP stack runs pre-emptibly now. From Eric
Dumazet.
9) Fix crash in fixed_phy_add, from Rabin Vincent.
10) Fix length checks in xen-netback, from Paul Durrant.
11) Fix mixup in KEY vs KEYID macsec attributes, from Sabrina Dubroca.
12) RDS connection spamming bug fixes from Sowmini Varadhan
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (152 commits)
net: suppress warnings on dev_alloc_skb
uapi glibc compat: fix compilation when !__USE_MISC in glibc
udp: prevent skbs lingering in tunnel socket queues
bpf: teach verifier to recognize imm += ptr pattern
bpf: support decreasing order in direct packet access
net: usb: ch9200: use kmemdup
ps3_gelic: use kmemdup
net:liquidio: use kmemdup
bpf: Use mount_nodev not mount_ns to mount the bpf filesystem
net: cdc_ncm: update datagram size after changing mtu
tuntap: correctly wake up process during uninit
intel: Add support for IPv6 IP-in-IP offload
ip6_gre: Do not allow segmentation offloads GRE_CSUM is enabled with FOU/GUE
RDS: TCP: Avoid rds connection churn from rogue SYNs
RDS: TCP: rds_tcp_accept_worker() must exit gracefully when terminating rds-tcp
net: sock: move ->sk_shutdown out of bitfields.
ipv6: Don't reset inner headers in ip6_tnl_xmit
ip4ip6: Support for GSO/GRO
ip6ip6: Support for GSO/GRO
ipv6: Set features for IPv6 tunnels
...
page_reference manipulation functions are introduced to track down
reference count change of the page. Use it instead of direct
modification of _count.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In function bgx_lmac_handler only use a member of
lmac after checking it is not null.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserved fields should be set to zero to avoid exposing
bits from the kernel stack.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible, although unlikely, that probing will find the
phy_device for the first LMAC of a thunder BGX device, but then need
to fail with -EPROBE_DEFER on a subsequent LMAC. In this case, we
need to call put_device() on each of the phy_devices that were
obtained, but will be unused due to returning -EPROBE_DEFER.
Also, since we can break out of the probing loop early, we need to
explicitly call of_node_put() outside of the loop.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the call to force the octeon-mdio driver to be loaded. Allow
the standard driver loading mechanisms to load the PHY drivers, and
use -EPROBE_DEFER to cause the BGX driver to be probed only after the
PHY drivers are available.
Reorder the setting of MAC addresses and PHY probing to allow BGX
LMACs with no attached PHY to still be assigned a MAC address.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjusted nicvf structure such that all elements used in hot
path like napi, xmit e.t.c fall into same cache line. This reduced
no of cache misses and resulted in ~2% increase in no of packets
handled on a core.
Also modified elements with :1 notation to boolean, to be
consistent with other element definitions.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of calling get_page() for every receive buffer carved out
of page, set page's usage count at the end, to reduce no of atomic
calls.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
On Thunderx pass 1.x and pass2 due to a HW errata default CQ
DROP_LEVEL of 0x80 is not sufficient to avoid CQ_WR_FULL Qset
error when packets are being received at >20Mpps resulting in
complete stall of packet reception.
This patch will configure it to 0x100 which is what is expected
by HW on Thunderx. On future passes of thunderx and other chips
HW default/reset value will be 0x100 or higher hence not overwritten.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Counting rx packets for every CQE_RX in CQ irq handler is incorrect.
Synchronization is missing when multiple queues are receiving packets
simultaneously. Like transmit packet stats use HW stats here.
Also removed unused 'cqe_type' parameter in nicvf_rcv_pkt_handler().
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For secondary Qsets 'hw_tso' is not getting set as probe() returns
much earlier. Fixed it by moving silicon revision check.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a interface is assigned morethan 8 queues and the logical interface
is toggled i.e down & up, additional queues or qsets are not initialized
as secondary qset count is being set to zero while tearing down.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate higher order pages when pagesize is small, this will
reduce number of calls to page allocator and wastage of memory.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of OF device tree, the firmware information is attached to
the BGX device structure in the standard manner, so use the firmware
iterators and accessors where possible.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This affinity hint can be used by user space irqbalance tool to set
preferred CPU mask for irqs registered by this VF. Irqbalance needs
to be in 'exact' mode to set irq affinity same as indicated by
affinity hint.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_schedule is being called from hard irq context, hence
switch to napi_schedule_irqoff which avoids unneeded call
to local_irq_save and local_irq_restore.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When system is low on atomic memory, too many error messages are logged.
Since this is not a total failure but a simple switch to non-atomic allocation
better to have a stat.
Also add a stat for reset, kicked due to transmit watchdog timeout.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is introduced in pass-2 chip and with this CQ interrupt
coalescing will work based on both timer and count.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for offloading TCP segmentation to HW in pass-2
revision of hardware. Both driver level SW TSO for pass1.x chips
and HW TSO for pass-2 chip will co-exist. Modified SQ descriptor
structures to reflect pass-2 hw implementation.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bc69fdfc6c
("net: thunderx: Enable BGX LMAC's RX/TX only after VF is up")
introduces lmac_cnt member and starts verifying VF number against it.
This is plain wrong, and works only because currently we have hardcoded
1:1 mapping between VFs and LMACs, and in this case num_vf_en and
lmac_cnt are always equal. However in future this may change, and the
code will badly misbehave. The worst consequence of this is failure to
deliver link status messages, causing VFs to go defunct because since
commit 0b72a9a106 ("net: thunderx: Switchon carrier only upon
interface link up") VF will not fully bring itself up without it.
This patch fixes the potential problem by doing VF number checks against
the num_vf_en. Since lmac_cnt is not used anywhere else, it is removed.
Additionally some duplicated code is factored out into nic_enable_vf()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have moved on to using allocated pages to carve receive
buffers instead of netdev_alloc_skb() there is no need to store
any pointers for later retrieval. Earlier we had to store
skb and skb->data pointers which later are used to handover
received packet to network stack.
This will avoid an unnecessary cache miss as well.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same switch-case repeates for nivc_*_intr functions.
In this patch it is moved to a helper nicvf_int_type_to_mask().
By the way:
- Unneeded write to NICVF register dropped if int_type is unknown.
- netdev_dbg() is used instead of netdev_err().
Signed-off-by: Yury Norov <yury.norov@auriga.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Acked-by: Vadim Lomovtsev <Vadim.Lomovtsev@caiumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable or disable BGX LMAC's RX/TX based on corresponding VF's
status. If otherwise, when multiple LMAC's physical link is up
then packets from all LMAC's whose corresponding VF is not yet
initialized will get forwarded to VF0. This is due to VNIC's default
configuration where CPI, RSSI e.t.c point to VF0/QSET0/RQ0.
This patch will prevent multiple copies of packets on VF0.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call netif_carrier_on() only if interface's link is up. Switching this on
upon IFF_UP by default, is causing issues with ethernet channel bonding
in LACP mode. Initial NETDEV_CHANGE notification was being skipped.
Also fixed some issues with link/speed/duplex reporting via ethtool.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly set CQ timer threshold and also set it to 2us.
With previous incorrect settings it was set to 0.5us which is too less.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While VNIC or BGX driver teardown, wait for already scheduled delayed work to
finish before destroying it.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases the crash is caused by nicvf_remove() being called from
outside. For example, if we try to feed the device to vfio after the
probe has failed for some reason. So, move the check to better place.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device probe fails, driver remains bound to the PCI device. However,
driver data has been reset to NULL. This causes crash upon dereferencing
it in nicvf_remove()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
