So a few people complained that
commit 177cf92de4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Apr 1 22:14:59 2014 +0200
drm/crtc-helpers: fix dpms on logic
which was merged into 3.15-rc1, broke resume on radeons. Strangely git
bisect lead everyone to
commit 25f397a429
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 19 18:57:11 2013 +0200
drm/crtc-helper: explicit DPMS on after modeset
which was merged long ago and actually part of 3.14.
Digging deeper I've noticed (again) that the call to
drm_helper_resume_force_mode in the radeon resume handlers was a no-op
previously because everything gets shut down on suspend. radeon does
this with explicit calls to drm_helper_connector_dpms with DPMS_OFF.
But with 177c we now force the dpms state to ON, so suddenly
resume_force_mode actually forced the crtcs back on.
This is the intention of the change after all, the problem is that
radeon resumes the fbdev console layer _before_ restoring the display,
through calling fb_set_suspend. And fbcon does an immediate ->set_par,
which in turn causes the same forced mode restore to happen.
Two concurrent modeset operations didn't lead to happiness. Fix this
by delaying the fbcon resume until the end of the readeon resum
functions.
v2: Fix up a bit of the spelling fail.
References: https://lkml.org/lkml/2014/5/29/1043
References: https://lkml.org/lkml/2014/5/2/388
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=74751
Tested-by: Ken Moffat <zarniwhoop@ntlworld.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ken Moffat <zarniwhoop@ntlworld.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Architecture rename/split.. ARCH_QCOM is for the non-legacy platforms
(ie. device-tree, multiplatform support, etc).
Signed-off-by: Rob Clark <robdclark@gmail.com>
The hotplug detect and irq does not seem to be reliable on all devices
for some reason. For now it is more reliable to use polling, and give
preference to raw gpio status if it disagrees with the debounced hpd
status.
Signed-off-by: Rob Clark <robdclark@gmail.com>
It hangs the hardware.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
This makes drm_get_encoder_name() thread safe.
Reference: http://lkml.kernel.org/r/645ee6e22cad47d38a2b35c21c8d5fe3@DC1-MBX-01\
.ptsecurity.ru
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Parsing device descriptors can fail due to a failed memory
allocation. The error needs to be properly propagated to the
upper layers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is pure evil. Userspace, I'm looking at you SNA, repacks batch
buffers on the fly after generation as they are being passed to the
kernel for execution. These batches also contain self-referenced
relocations as a single buffer encompasses the state commands, kernels,
vertices and sampler. During generation the buffers are placed at known
offsets within the full batch, and then the relocation deltas (as passed
to the kernel) are tweaked as the batch is repacked into a smaller buffer.
This means that userspace is passing negative relocations deltas, which
subsequently wrap to large values if the batch is at a low address. The
GPU hangs when it then tries to use the large value as a base for its
address offsets, rather than wrapping back to the real value (as one
would hope). As the GPU uses positive offsets from the base, we can
treat the relocation address as the minimum address read by the GPU.
For the upper bound, we trust that userspace will not read beyond the
end of the buffer.
So, how do we fix negative relocations from wrapping? We can either
check that every relocation looks valid when we write it, and then
position each object such that we prevent the offset wraparound, or we
just special-case the self-referential behaviour of SNA and force all
batches to be above 256k. Daniel prefers the latter approach.
This fixes a GPU hang when it tries to use an address (relocation +
offset) greater than the GTT size. The issue would occur quite easily
with full-ppgtt as each fd gets its own VM space, so low offsets would
often be handed out. However, with the rearrangement of the low GTT due
to capturing the BIOS framebuffer, it is already affecting kernels 3.15
onwards. I think only IVB+ is susceptible to this bug, but the workaround
should only kick in rarely, so it seems sensible to always apply it.
v3: Use a bias for batch buffers to prevent small negative delta relocations
from wrapping.
v4 from Daniel:
- s/BIAS/BATCH_OFFSET_BIAS/
- Extract eb_vma_misplaced/i915_vma_misplaced since the conditions
were growing rather cumbersome.
- Add a comment to eb_get_batch explaining why we do this.
- Apply the batch offset bias everywhere but mention that we've only
observed it on gen7 gpus.
- Drop PIN_OFFSET_FIX for now, that slipped in from a feature patch.
v5: Add static to eb_get_batch, spotted by 0-day tester.
Testcase: igt/gem_bad_reloc
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78533
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only want to modifiy a single field in the userspace view of the
execbuffer command buffer, so explicitly change that rather than copy
everything back again.
This serves two purposes:
1. The single fields are much cheaper to copy (constant size so the
copy uses special case code) and much smaller than the whole array.
2. We modify the array for internal use that need to be masked from
the user.
Note: We need this backported since without it the next bugfix will
blow up when userspace recycles batchbuffers and relocations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A single object may be referenced by multiple registers fundamentally
breaking the static allotment of ids in the current design. When the
object is used the second time, the physical address of the first
assignment is relinquished and a second one granted. However, the
hardware is still reading (and possibly writing) to the old physical
address now returned to the system. Eventually hilarity will ensue, but
in the short term, it just means that cursors are broken when using more
than one pipe.
v2: Fix up leak of pci handle when handling an error during attachment,
and avoid a double kmap/kunmap. (Ville)
Rebase against -fixes.
v3: And fix the error handling added in v2 (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77351
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
shmem_read_mapping_page() uses mapping_gfp_mask(mapping) as default gfp
mask. No reason to use shmem_read_mapping_page_gfp() directly if we want
the default behavior.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
shmem supports page-relocations during swapin since quite some time. It
was implemented in:
commit bde05d1ccd
Author: Hugh Dickins <hughd@google.com>
Date: Tue May 29 15:06:38 2012 -0700
shmem: replace page if mapping excludes its zone
The gem-comment about wrongly placed DMA32 pages is no longer valid.
Replace it with a proper comment but keep the BUG_ON() to verify correct
shmem behavior.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The shmobile DRM driver is only useful on SuperH and shmobile unless
build testing. I am dropping the SuperH dependencies though because
the driver doesn't even build there, so in practice it is an arm-only
driver for now.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The Renesas R-Car Display Unit driver is only useful on shmobile
unless build testing. The LVDS output is useful on an even more
reduced hardware set.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
acpi_video_backlight_support() is supposed to be called by other (vendor
specific) firmware backlight controls, not by native / raw backlight controls
like nv_backlight.
Userspace will normally prefer firmware interfaces over raw interfaces, so
if acpi_video backlight support is present it will use that even if
nv_backlight is registered as well.
Except when video.use_native_backlight is present on the kernel cmdline
(or enabled through a dmi based quirk). As the name indicates the goal here
is to make only the raw interface available to userspace so that it will use
that (it only does this when it sees a win8 compliant bios).
This is done by:
1) Not registering any acpi_video# backlight devices; and
2) Making acpi_video_backlight_support() return true so that other firmware
drivers, ie acer_wmi, thinkpad_acpi, dell_laptop, etc. Don't register their
own vender specific interfaces.
Currently nouveau breaks this setup, as when acpi_video_backlight_support()
returns true, it does not register itself, resulting in no backlight control
at all.
This is esp. going to be a problem with 3.16 which will default to
video.use_native_backlight=1, and thus nouveau based laptops with a win8 bios
will get no backlight control at all.
This also likely explains why the previous attempt to make
video.use_native_backlight=1 the default was not a success, as without this
patch having a default of video.use_native_backlight=1 will cause regressions.
Note this effectively reverts commit 5bead799d3 (drm/nouveau: don't
expose backlight control when available through ACPI).
References: https://bugzilla.redhat.com/show_bug.cgi?id=1093171
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The 800x600 (SVGA) screen resolution was lacking in the set of
built-in selectable EDID screen resolutions that can be used to
repair misbehaving monitor firmware.
This patch adds the related data set and expands the documentation.
Note that the SVGA bit occupies a different byte to all the existing
users of the established timing bits forcing a rework of the
ESTABLISHED_TIMINGS_BITS macro.
Tested new EDID on an aged (and misbehaving) industrial LCD panel;
existing EDIDs still pass edid-decode's checksum checks.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: linux-doc@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's barely alive now anyway, so give it the "coup de grâce".
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Up until now, contexts had one (and only one) backing object that was
used by the hardware to save/restore render ring contexts (via the
MI_SET_CONTEXT command). Other rings did not have or need this, so
our i915_hw_context struct had a 1:1 relationship with a a real HW
context.
With Logical Ring Contexts and Execlists, this is not possible anymore:
all rings need a backing object, and it cannot be reused. To prepare
for that, rename our contexts to the more generic term intel_context.
No functional changes.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Manual cleanup after the previous Coccinelle script.
Yes, I could write another Coccinelle script to do this but I
don't want labor-replacing robots making an honest programmer's
work obsolete (also, I'm lazy).
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As advanced by the previous patch, the ringbuffers and the engine
command streamers belong in different structs. This is so because,
while they used to be tightly coupled together, the new Logical
Ring Contexts (LRC for short) have a ringbuffer each.
In legacy code, we will use the buffer* pointer inside each ring
to get to the pertaining ringbuffer (the actual switch will be
done in the next patch). In the new Execlists code, this pointer
will be NULL and we will use instead the one inside the context
instead.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the upcoming patches we plan to break the correlation between
engine command streamers (a.k.a. rings) and ringbuffers, so it
makes sense to refactor the code and make the change obvious.
No functional changes.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, we disable GT power saving during the end of the suspend sequence
in i915_save_state(). Doing the disabling at that point seems arbitrary.
One reason to disable it early though is to have a quiescent HW state
before we do anything else (for example save registers). So move the
disabling earlier, which also takes care canceling of the deferred RPS
enabling work done by intel_disable_gt_powersave().
Note that after the move we'll call intel_disable_gt_powersave() only
in case modeset is enabled, but that's anyway the only case where we
have it enabled in the first place.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In
commit c6df39b5ea
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Apr 14 20:24:29 2014 +0300
drm/i915: get a runtime PM ref for the deferred GT powersave enabling
I added an RPM get-ref when enabling RPS from a deferred work, but forgot
to add the corresponding put-ref when canceling the work. This may leave
RPM disabled.
Note that the race is real since we run the rps enabling with a
delayed work item after resume, so leaves enough time (in contrived
examples) to fit a quick autoresum in.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Testecase: igt/pm_rpm/system-suspend
[danvet: Mention testcase and add note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently user space can access GEM buffers mapped to GTT through
existing mappings concurrently while the platform specific suspend
handlers are running. Since these handlers may change the HW state in a
way that would break such accesses, remove the mappings before calling
the handlers. Spotted by Ville.
Also Chris pointed out that the lists that i915_gem_release_all_mmaps()
walks through need dev->struct_mutex, so take this lock. There is a
potential deadlock against a concurrent RPM resume, resolve this by
aborting and rescheduling the suspend (Daniel).
v2:
- take struct_mutex around i915_gem_release_all_mmaps() (Chris, Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we need to disable VCP unit clock gating around media reset
on g4x.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen2 the scanline counter behaves a bit differently from the
later generations. Instead of adding one to the raw scanline
counter value, we must subtract one.
On HSW/BDW the scanline counter requires a +2 adjustment on HDMI
outputs. DP outputs on the on the other require the typical +1
adjustment.
As the fixup we must apply to the hardware scanline counter
depends on several factors, compute the desired offset at modeset
time and tuck it away for when it's needed.
v2: Clarify HSW+ situation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78997
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs are a bit lacking when it comes to describing when certain
timing related events occur in the hardware. Draw a picture which
tries to capture the most important ones.
v2: Clarify a few details (Imre)
v3: Add HSW+ HDMI scanline counter numbers
Acked-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the logic to fix up the frame counter on gen3/4 assumes that
start of vblank occurs at vblank_start*htotal pixels, when in fact
it occurs htotal-hsync_start pixels earlier. Apply the appropriate
adjustment to make the frame counter more accurate.
Also fix the vblank start position for interlaced display modes.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In interlaced modes, the pixel counter counts all pixels,
so one field will have htotal more pixels. In order to avoid
the reported position from jumping backwards when the pixel
counter is beyond the length of the shorter field, just
clamp the position the length of the shorter field. This
matches how the scanline counter based position works since
the scanline counter doesn't count the two half lines.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: "Akash Goel <akash.goels@gmail.com>"
Reviewed-by: "Sourab Gupta <sourabgupta@gmail.com>"
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel keeps on ramping up the warning level of the DRM and our display
core to make it complain whenever the locking rules are not followed.
This caught
commit 24576d2397
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Mar 26 09:25:45 2013 -0700
drm/i915: enable VT switchless resume v3
introducing an unlocked access to the CRTC whilst disabling it for
suspend.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78114
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before purging our pages (as opposed to copying back the contents from
the GPU), make sure that there is not an exposed CPU mmapping through
which the user can inspect the results.
Regression from
commit 5537252b6b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Mar 25 13:23:06 2014 +0000
drm/i915: Invalidate our pages under memory pressure
Testcase: igt/gem_mmap/new-object
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79005
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have to write to the primary plane base address registrer when we
enable/disable the primary plane in response to sprite coverage. Those
writes will cause the flip counter to increment which could interfere
with the detection of CS flip completion. We could end up completing
CS flips before the CS has even executed the commands from the ring.
To avoid such issues, wait for CS flips to finish before we toggle the
primary plane on/off.
v2: Rebased due to atomic sprite update changes
Testcase: igt/kms_mmio_vs_cs_flip/setplane_vs_cs_flip
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the current code, we unconditionally touch
HSW_AUD_PIN_ELD_CP_VLD, which means we can touch it when the power
well is off, and that will trigger an "Unclaimed register" message.
Just adding the intel_crtc->config.has_audio should already avoid the
unclaimed register messsages, but since we actually need the power
well to make the Audio code work, it makes sense to also grab the
audio power domain reference, and release it when it's not needed
anymore.
I used IGT's pm_rpm to reproduce this bug, but it can probably be
reproduced on other tests that do modesets. I'm using a machine with
eDP+HDMI connected.
Regression introduced by:
commit acfa75b02e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Apr 24 23:54:51 2014 +0200
drm/i915: Simplify audio handling on DDI ports
Credits to Daniel for suggesting this implementation.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because this will trigger "Unclaimed register" messages. All I need to
reproduce this problem is to boot my HSW machine with eDP+HDMI
connected.
Regression introduced by:
commit 9ed109a7b4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Apr 24 23:54:52 2014 +0200
drm/i915: Track has_audio in the pipe config
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding stuff at the bottom is really no how this should be done, since
that's the place for ums/dri dungeons.
This was added in
commit a8ebba75b3
Author: Zhao Yakui <yakui.zhao@intel.com>
Date: Thu Apr 17 10:37:40 2014 +0800
drm/i915: Use the coarse ping-pong mechanism based on drm fd to dispatch the BSD command on BDW GT3
Also add a note to prevent this from happening again - people really
should be less lazy and take more time to look for a good home of
their new driver-global state.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gen2 reports FIFO underruns whenever no planes are enabled on the pipe.
So in order to avoid false positives we must enable the FIFO underrun
reporting only when at least one plane is enabled on the pipe. For
now just move the underrun reporting enable/disable points to the
other side of the plane enable/disable point. That doesn't cover cases
when we turn off all the planes for the pipe but leave the pipe running
on purpose, but it's better than the current situation.
On gen4+ we can actually move the underrun reporting enable/disable to
the opposite ends of the crtc enable/disable hooks. I suppose in theory
we could leave the underrun reporting enabled all the time, except on
VLV where PIPESTAT stops working when the display power well is down.
If we ever get around to unifying the PIPESTAT irq handling for all
gmch platforms, we should still follow the VLV route for other platforms.
It would also micro-optimize the irq handler a bit since we could then
skip the PIPESTAT reads for all disabled pipes.
Gen3 is still a mystery, but for now I'm going to assume it behaves
like gen4+.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Checking whether the error interrupt was enabled or not isn't really
necessary when we check for uncleared FIFO underruns. If it was enabled
we'll race with the interrupt handler a bit, but that seems OK as we
still claim the interrupt.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIFO underruns don't generate interrupts on gmch platforms, so
if we want to know whether a modeset triggered FIFO underruns we
need to explicitly check for them.
As a modeset on one pipe could cause underruns on other pipes,
check for underruns on all pipes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
[danvet: Fix up merge error, kudos to Ville for noticing it.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIFO underruns don't generate an interrupt on gmch platforms, so we
should check whether there were any that we failed to notice when
we're disabling FIFO underrun reporting.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Noticed by Thierry Reding in his review, but I've merged the drm
vblank rework topic branch a bit too quickly. So separate fixup.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Document the internal structure of the VLV display PHY a bit to help
people understand how the different register blocks relate to each
other.
v2: Add a bit more text
Make it a DOC: comment, but leave the ascii art out since
it would get mangled
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
for proper refcounting to take place as we use
i915_add_request() for it.
i915_add_request() also takes the context for the request
from ring->last_context so move the null state batch
submission after the ring context has been set.
v2: we need to check for correct ring now (Ville Syrjälä)
v3: no need to expose i915_gem_move_object_to_active (Chris Wilson)
v4: cargoculted vma/active/inactive error handling removed (Chris Wilson)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
radeon fixes, VCE one is big but does fix a userspace crash.
* 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon/pm: don't allow debugfs/sysfs access when PX card is off (v2)
drm/radeon: avoid segfault on device open when accel is not working.
drm/radeon: fix typo in finding PLL params
drm/radeon: fix register typo on si
drm/radeon: fix buffer placement under memory pressure v2
drm/radeon: fix page directory update size estimation
drm/radeon: handle non-VGA class pci devices with ATRM
drm/radeon: fix DCE83 check for mullins
drm/radeon: check VCE relocation buffer range v3
drm/radeon: also try GART for CPU accessed buffers
fixes nasty panel bleeding bug.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/gf119-/disp: fix nasty bug which can clobber SOR0's clock setup
drm/nvd9/therm: handle another kind of PWM fan
If a pipe is already active when we init/resume there might not be a
full modeset afterwards so drm_vblank_on() may not get called. In such
a case if someone is holding a vblank reference across a suspend/resume
cycle drm_vblank_get() called after resuming won't re-enable the vblank
interrupts.
So in order to make sure vblank interrupts get re-enabled post-resume,
call drm_vblank_on() in intel_sanitize_crtc() if the crtc is already
active.
v2: Also drm_vblank_off() if the pipe got disabled magically
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Testecase: igt/kms_flip/vblank-vs-suspend
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in the drm vblank rework from Ville and me. drm core parts acked
by Dave Airlie
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Just a bit of fun around the placement of drm_vblank_on. This merge
resolution has been tested in drm-intel-nightly for a while already.
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't have hardware based disable bits on gmch platforms, so need
to block spurious underrun reports in software. Which means that we
_must_ start out with fifo underrun reporting disabled everywhere.
This is in big contrast to ilk/hsw/cpt where there's only _one_
disable bit for all platforms and hence we must allow underrun
reporting on disabled pipes. Otherwise nothing really works,
especially the CRC support since that's key'ed off the same irq
disable bit.
This allows us to ditch the fifo underrun reporting hack from the vlv
runtime pm code and unexport the internal function from i915_irq.c
again. Yay!
v2: Keep the display irq disabling, spotted by Imre.
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we unconditionally dtrt when disabling/enabling crtcs we
don't need any hacks any longer to keep the vblank logic sane when
all the registers go poof. So let's rip it all out.
This essentially undoes
commit 9dbd8febb4
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Jul 23 10:48:11 2013 -0300
drm/i915: update last_vblank when disabling the power well
Apparently igt/kms_flip is already powerful enough to exercise this
properly, yay! See the reference regression report for details.
v2: Update testcase name
References: https://bugs.freedesktop.org/show_bug.cgi?id=66808
Testcase: igt/kms_flip/vblank-vs-*-rpm
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only the low-level irq handling functions still use integer crtc
indices with this. But fixing that will require a lot more sugery
and some good ideas for backwards compat with old ums userspace.
Both in drivers and in the drm core.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to start somewhere ... With this the only places left in i915
where we use pipe integers is in the interrupt handling code. And
there it actually makes some amount of sense.
v2:
- Polish kerneldoc a bit (Thierry).
- Drop "dev" parameter since it's unecessary.
- Split out i915 changes (Thierry).
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Integrate into the drm DocBook
- Disable kerneldoc for functions not exported to drivers.
- Properly document the new drm_vblank_on|off and add cautious
comments explaining when drm_vblank_pre|post_modesets shouldn't be
used.
- General polish and OCD.
v2: Polish as suggested by Thierry.
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Originally these functions have been for user modesetting drivers to
ensure vblank processing doesn't fall over completely around modeset
changes. This has been carried over ever since then.
Now that Ville cleaned our vblank handling with an explicit
drm_vblank_off/on braket when disabling/enabling crtcs. So this seems
to be unnecessary now. The most important side effect was that due to
the delayed vblank disabling we have been pretty much guaranteed to
receive a vblank interrupt soonish after a crtc was enabled.
Note that our vblank handling across modeset is still fairly decent
fubar - we don't actually handle vblank counter all to well.
drm_update_vblank_count will make sure that the frame counter always
rolls forward, but userspace isn't really all to ready to cope with
the big jumps this causes.
This isn't a big mostly because the hardware retains the frame
counter. But with runtime pm and also across suspend/resume we fall
over.
Fixing this is a lot more involved and also needs som i-g-ts. So
material for another patch series.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All of the .queue_flip() callbacks duplicate the same code to pin the
buffers and calculate the gtt_offset. Move that code to
intel_crtc_page_flip(). In order to do that we must also move the ring
selection logic there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we've plugged the mmio vs. ring flip race, we shouldn't need
these vblank waits in the modeset codepaths anymore. So get rid of
them.
v2: gen2 needs to wait for planes to turn off before disabling pipe
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the vblank wait is gone from intel_enable_primary_plane(),
hsw_enable_ips() needs to do the vblank wait itself.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting from ILK, mmio flips also cause a flip done interrupt to be
signalled. This means if we first do a set_base and follow it
immediately with the CS flip, we might mistake the flip done interrupt
caused by the set_base as the flip done interrupt caused by the CS
flip.
The hardware has a flip counter which increments every time a mmio or
CS flip is issued. It basically counts the number of DSPSURF register
writes. This means we can sample the counter before we put the CS
flip into the ring, and then when we get a flip done interrupt we can
check whether the CS flip has actually performed the surface address
update, or if the interrupt was caused by a previous but yet
unfinished mmio flip.
Even with the flip counter we still have a race condition of the CS flip
base address update happens after the mmio flip done interrupt was
raised but not yet processed by the driver. When the interrupt is
eventually processed, the flip counter will already indicate that the
CS flip has been executed, but it would not actually complete until the
next start of vblank. We can use the DSPSURFLIVE register to check
whether the hardware is actually scanning out of the buffer we expect,
or if we managed hit this race window.
This covers all the cases where the CS flip actually changes the base
address. If the base address remains unchanged, we might still complete
the CS flip before it has actually completed. But since the address
didn't change anyway, the premature flip completion can't result in
userspace overwriting data that's still being scanned out.
CTG already has the flip counter and DSPSURFLIVE registers, and
although the flip done interrupt is still limited to CS flips alone,
the code now also checks the flip counter on CTG as well.
v2: s/dspsurf/gtt_offset/ (Chris)
Testcase: igt/kms_mmio_vs_cs_flip/setcrtc_vs_cs_flip
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73027
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add g4x_ prefix to flip_count_after_eq.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We really just want to go detect displays again and fire off a hotplug
event if things have changed, not go through full hotplug processing.
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since
commit 2e82a72031
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Jan 17 15:46:43 2014 +0200
drm/i915: don't disable DP port after a failed link training
and
commit 5d6a1116c6
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Jan 16 18:35:57 2014 +0200
drm/i915: don't disable the DP port if the link is lost
we no longer call intel_dp_link_down from generic DP code, but only
from the !HAS_DDI dp encoder functions. hsw/bdw have their own encoder
disabling callback in intel_ddi.c.
Hence the early return is no longer needed and the big comment just
confusing, so let's rip it out. To ensure what we don't accidentally
use this again on ddi encoders add a WARN_ON instead.
Spotted while reading through intel_dp.c
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_vblank_off() will turn off vblank interrupts, but as long as the
refcount is elevated drm_vblank_get() will not re-enable them. This
is a problem is someone is holding a vblank reference while a modeset is
happening, and the driver requires vblank interrupt to work during that
time.
Add drm_vblank_on() as a counterpart to drm_vblank_off() which will
re-enabled vblank interrupts if the refcount is already elevated. This
will allow drivers to choose the specific places in the modeset sequence
at which vblank interrupts get disabled and enabled.
Testcase: igt/kms_flip/*-vs-suspend
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add Testcase tag for the igt I've written.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If there's a blocking vblank wait in progress while the vblank interrupt
gets disabled, the current code will just let the vblank wait time out.
Instead make it return immediately when vblank interrupts get disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently there's one per-device vblank disable timer, and it gets
reset wheneven the vblank refcount for any crtc drops to zero. That
means that one crtc could accidentally be keeping the vblank interrupts
for other crtcs enabled even if there are no users for them. Make the
disable timer per-crtc to avoid this issue.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The irq flags state is already established by the outer
spin_lock_irqsave(); re-disabling irqs is redundant.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow a few functions have been dropped in the middle of backlight
code. Move them around. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clear the reset domain after a succesful GPU reset on ilk. We already
do that on gen4, so let's try to be a bit more consistent. And if
ether render or media reset fails, we might use the leftover value
in the register to pinpoint the culprit.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the other bits in the GDSR register are read-only, so we don't have
to preserve them when we perform a GPU reset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I'm trying to reduce the WARNs during driver reload and this was one of
them. Also while at it remove the redundant condition from before
unregister_shrinker().
v2:
- fix the error path too and move the unregister to its logical place
(Chris)
- remove redundant condition from before unregister_shrinker()
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The comments in i915_reg.h aren't proper kernel-doc comments, so replace
the magic /** with just /*
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The following workarounds should be needed for pre-production hardware
only:
* WaDisablePwrmtrEvent:chv
* WaSetMaskForGfxBusyness:chv
* WaDisableGunitClockGating:chv
* WaDisableFfDopClockGating:chv
* WaDisableDopClockGating:chv
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec only tells us to set individual bits here and there. So we use
RMW for most things. Do the same for the swing calc init.
Eventually we should optimize things to just blast the final value in
with group access whenever possible. But to do that someone needs to
take a good look at what's the reset value for each registers, and
possibly if the BIOS manages to frob with some of them. For now
use RMW access always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like PCS, TX group reads return 0xffffffff. So we need to target each
lane separately if we want to use RMW cycles to update the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All PCS groups access reads return 0xffffffff, so we can't use group
access for RMW cycles. Instead target each spline separately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fight conflict with misplaced ; .... ARGH!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits we've been setting so far only progagate the reset singal to
the data lanes. To actaully force the reset signal we need to set another
override bit.
v2: Fix mispalced ';' (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Seems like we shouldn't leave the data lane resert deasserted when
the port if disabled. So propagate the reset the data lanes in
the encoder .post_disable() hook.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During the enable sequence we first enable the dclkp output to the
display controller, and then enable the PLL. Do the opposite during
the disable sequence.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to pick the correct data lanes based on the port not the
pipe, so move the data lane deassert into the encoder .pre_enable()
hook from the chv_enable_pll().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Setup the pipe config dpll state correctly for CHV. Also add
a assert_pipe_disabled() to chv_disable_pll(), and program the
DPLL_MD registers in chv_enable_pll().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the encoder .get_config hooks to report the correct active pipe for
CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has three pipes so let's expose them all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unsurprisingly the cursor C regiters are also at a weird offset on CHV.
Add more pipe offsets to handle them.
This also gets rid of most of the differences between the i9xx vs. ivb
cursor code. We can unify the remaining code as well, but I'll leave
that for another patch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CHV the GMBUS port for port D is different from other gmch platforms
which have port D. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CHV pipe C can driver only port D, and pipes A and B can drivbe only
ports B and C. Configure the crtc_mask appropriately to reflect that.
v2: Moar braces (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for the third pipe in cherrview
v2: Don't use spaces for indentation (Jani)
Wrap long lines
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: slightly massaged the patch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cherryview also needs this WA.
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: Looks like it's for pre-prodution hw only]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We implement the following workarounds:
* WaDisableAsyncFlipPerfMode:chv
* WaProgramMiArbOnOffAroundMiSetContext:chv
v2: Drop WaDisableSemaphoreAndSyncFlipWait note
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This workaround is listed for CHV, but not for BDW. However BSpec notes
that on BDW CSunit clock gating is always disabled irrespective of the
relevant bit in the GEN6_UGCTL1 registers. For CHV however, such text
is not present in BSpec, so it seems safer to just set the bit.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW has the same requirement but the w/a database doens't list
this w/a for BDW. Seems to be another one of those "stick a bunch
of known workarounds into this bag and write something on the label"
type of things.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Besides the fairly useless BUG_ON the logic is completely generic
and cane be used on any platform what wants to reuse the shared
dpll support code.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the last piece of code which write state to the hardware in
the ironalake ->crtc_mode_set callback.
I think we could merge this with the pll->enable hook, but otoh the
ordering requirements with the ldvs port are really tricky. Doing the
FP0/1 writes up-front before we even prepare the lvds port (in the
pre_pll_enable hook) like on i9xx seems safest.
With this ilk+ platforms are now ready for runtime PM with DPMS. Since
hsw/bdw also support runtime pm besides snb we need to first make the
haswell code save before we can touch the core code.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of every time it isn't active: We only need to do that when
the pll is currently unused, i.e. when pll->refcount == 0. For
paranoia add a warning for the ibx case where plls have a fixed
mapping and hence should always be unused after the call to
intel_put_shared_dpll.
v2: Simplify control flow and use struct assignment instead of memcpy
as suggested by Damien.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the PX card is off don't try and access it. Avoid hw access
to the card while it's off (e.g., reading back invalid temperature).
v2: be less strict
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=76321
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christian König <christian.koenig@amd.com>
When accel is not working on device with virtual address space radeon
segfault because the ib buffer is NULL and trying to map it inside the
virtual address space trigger segfault. This patch only map the ib
buffer if accel is working.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Probably a copy paste typo.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Some buffers (UVD/VM page tables) must be placed in VRAM,
but the byte restriction for moving buffers didn't took this
into account.
v2: keep closer to the original code
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Take padding into account as well.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=75651
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Newer PX systems have non-VGA pci class dGPUs. Update
the ATRM fetch method to handle those cases.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=75401
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Mullins is DCE83 just like Kabini. Set the proper number
of endpoints on mullins.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
v2 (chk): fix image size storage
v3 (chk): fix UV size calculation
Signed-off-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
With this all hw writes are also gone from the ->crtc_mode_set hook on
vlv. I wondered whether we should track more of the pll state in the
pipe config, but otoh as long as we don't have shared plls that's not
really useful - the cross-checking of the port clock should be
sufficient.
While at it also de-magic some of the pipe checks, this has been
irking me since a long time.
Whit this vlv is now ready for runtime PM on dpms. If we'd have
runtime PM support in general ...
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These two writes are the very last hw writes from the
->crtc_modeset_callback on pre-gen5 hardware. As usual vlv is a bit
different, so this here is just warm-up.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again the same story: This code just transform sw state from the pipe
config into hardware state. And again we can't move the pll code, but
this time around because the state isn't properly tracked in the pipe
config.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again this code just transforms sw state from the pipe config into
hardware state, so we can just move it around. Unfortunately again a
few forward declarations since intel_display.c is becoming a bit of a
mess.
Note that both for i9xx and ironlake code the only things remaining in
the ->crtc_mode_set hook is now the clock state computation and
sharing code. That needs to be moved into the compute config stage so
that we can catch impossible configurations earlier.
Also note that some of the DPLL hw setup code is still run from within
->crtc_mode_set, namele the pll->mode_set callback. We need to move
that first before we can do fancy things like enable runtime PM for
dpms off.
v2: Make it compile again after the rebase, bisectability issue
reported by Wu Fengguang.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now this really should be in the pipe config somewhere, but till now
it isn't. We can at least move it up a bit next to all the other pll
code since intel_dp_set_m_n really doesn't depend upon this.
This is just prep work so that moving all the hw frobbing code from
->crtc_mode_set to ->crtc_enable is clean.
v2: Do the same for haswell while at it, not just for ivb.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All these functions simply convert sw state as encoded in the pipe
config or primary framebuffer into hardware state. So we can move them
all into the crtc enable hook. Unfortunately this means a little bit
of duplication between the i9xx and vlv functions, but since we
already have highly refactored code I think this is acceptable.
Also a pile of forward declarations unfortunately.
Note also that the various <platform>_update_pll functions are still
called from within the ->crtc_mode_set hook. Mostly they compute the
clock state for the pipe config, but unfortunately there are some
random register writes interspersed. Those need to be moved out first
before we can enable runtime PM for DPMS.
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before the process killer is invoked, oom-notifiers are executed for one
last try at recovering pages. We can hook into this callback to be sure
that everything that can be is purged from our page lists, and to give a
summary of how much memory is still pinned by the GPU in the case of an
oom. This should be really valuable for debugging OOM issues.
Note that the last-ditch effort call to shrink_all we've previously
called from our normal shrinker when we could free as much as the vm
demaned is moved into the oom notifier. Since the shrinker accounting
races against bind/unbind operations we might have called shrink_all
prematurely, which this approach with an oom notifier avoids.
References: https://bugs.freedesktop.org/show_bug.cgi?id=72742
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: lu hua <huax.lu@intel.com>
[danvet: Bikeshed logical | into || and pimp commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're using the reset domains bits for g4x on ilk. But on ilk those bits
actually shifted by one bit. Fix it up so that we use the correct bits.
We were actually always writing 0x2 to the reset domain bits, which
is a reserved value. In practice it looks like the hardware ignores that
value since nothing happens if I write that value when there's a 3D
workload running. Writing the _correct_ render domain value actually
makes the GPU stop.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should be waiting for the reset bit to clear, not remain set.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are comments in the gen4-5 reset functions stating that we can't
reset render and media without also doing a display reset. But that's
exactly what the code does, ie. we don't perform a display reset. Drop
the bogus comments.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to flush out dirty pages into the swapcache (and from there into the
swapfile) when under memory pressure and forced to drop GEM objects from
memory. In effect, this should just allow us to discard unused pages for
memory reclaim and to start writeback earlier.
v2: Hugh Dickins warned that explicitly starting writeback from
shrink_slab was prone to deadlocks within shmemfs.
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can share a few lines of tricky lock handling we need to use for both
shrinker routines and in the process fix the return value for count()
when reporting a deadlock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the machine is under a lot of memory pressure and being stressed by
multiple GPU threads, we quite often report fewer than shrinker->batch
(i.e. SHRINK_BATCH) pages to be freed. This causes the shrink_control to
skip calling into i915.ko to release pages, despite the GPU holding onto
most of the physical pages in its active lists.
References: https://bugs.freedesktop.org/show_bug.cgi?id=72742
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
shmemfs first checks if there is enough memory to allocate the page
and reports ENOSPC should there be insufficient, along with
the usual ENOMEM for a genuine allocation failure.
We use ENOSPC in our driver to mean that we have run out of aperture
space and so want to translate the error from shmemfs back to
our usual understanding of ENOMEM. None of the the other GEM users
appear to distinguish between ENOMEM and ENOSPC in their error handling,
hence it is easiest to do the fixup in i915.ko
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes a LVDS bleed issue on Lenovo W530 that can occur under a
number of circumstances.
Cc: <stable@vger.kernel.org > # v3.9+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Intel fixes for regressions, black screens and hangs, for 3.15.
* tag 'drm-intel-fixes-2014-05-16' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Increase WM memory latency values on SNB
drm/i915: restore backlight precision when converting from ACPI
drm/i915: Use the first mode if there is no preferred mode in the EDID
drm/i915/dp: force eDP lane count to max available lanes on BDW
drm/i915/vlv: reset VLV media force wake request register
drm/i915/SDVO: For sysfs link put directory and target in correct order
drm/i915: use lane count and link rate from VBT as minimums for eDP
drm/i915: clean up VBT eDP link param decoding
drm/i915: consider the source max DP lane count too
This patch adds a mmio base address variable for DSI display,
to make the DSI code generic, so that, if required, the same code
can be re-used for future platforms with different mmio base.
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can apperently miss them, but breaking the entire driver hampers
testing. So bail out after one minute, our customerary "this is a lost
cause" timeout.
References: https://bugs.freedesktop.org/show_bug.cgi?id=78383
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far we used the wrong opcodes to access the DSI registers, so the
register writes during DSI programming didn't actually succeed and left
the registers unchanged. This wasn't a problem for the initial modeset,
where the BIOS-programmed values happened to work, but after resuming
from s0ix these registers are reset and failing to program them results
in a blank screen.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These opcodes are not specific for an endpoint, but are the same for all
endpoints. So rename them accordingly, using the name the VLV2 sideband
HAS uses. Also move the macros to the .c file, since they aren't used
anywhere else.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixed several switch statements, curly braces, dereference operators
and keywords.
Signed-off-by: Robin Schroer <sulamiification@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our two ->crtc_mode_set callbacks really don't care whether the fb is
pinned and set up already or not - all the state computation and
handling which originally looked at the framebuffer is already using
the indirection through the pipe configuration.
Eventually we want to move this up a bit more, but as long as the crtc
mode_set callback still exists (and as long as we don't need to pin an
entire pile of planes due to atomic modesets) there's not much point
in it. So I'll let this be for now.
v2: Don't forget about haswell ...
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A lot of the code in set_base is uncessary when the crtc is off, so we
can get rid of it all. Also, we don't need to call the fbc/psr update
functions since the crtc enable/disable hooks do that already.
The only things we really need are:
- Pin the new framebuffer and potentially unpin the old framebuffer
(if the crtc has been on and we only change the configuration).
- Update the plane registers.
The first step will move out of platform code with the very next
patch.
v2: Don't forget about haswell ...
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My plan here is to split up set_base into a prepare step, which does
the pinning, and a commit stage, which updates the hw state. Eventually
we should be able to move the prepare step at the beginning of any
atomic update. For now I only want to move the commit step into the
crtc_enable callbacks.
As a prep step sprinkle intel_edp_psr_update all over the place so
that we don't have to concern ourselves with that in the commit step.
v2: Rebase on top of Ville's enable/disable functions for all planes.
v3: Rebase more.
Reviewed-by: Akash Goel <akash.goel@intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just for consistency, this patch won't fix anything really.
v2: Rebase over all the recent plane enabling shuffling.
Reviewed-by: Akash Goel <akash.goel@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Way back we've used this to reject framebuffers with unsupported
pixel formats. But since the modesetting reorg with the compute
config stage we reject those much earlier and just BUG() in this
callback. So switch to a void return type.
Reviewed-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
More fallout from
commit c8725f3dc0
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Mar 17 12:21:55 2014 +0000
drm/i915: Do not call retire_requests from wait_for_rendering
is that we can completely fill all of memory using small objects, such
that we exhaust the filp space, and spend all of our time evicting
objects from the aperture. As such, we never fill the ring, and never
trigger the last resort flushing in
commit 1cf0ba1474
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon May 5 09:07:33 2014 +0100
drm/i915: Flush request queue when waiting for ring space
and so all the requests are left active and the objects keep that last
active reference. Eventually the system comes to a halt as it runs out
of memory.
The impact is mainly limited to test cases as regular userspace will
trigger retirement by manually checking whether an object is active.
Testcase: igt/gem_lut_handle
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78724
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in latest updates to AST driver.
* 'ast-updates' of ssh://people.freedesktop.org/~/linux:
drm/ast: initial DP501 support (v0.2)
drm/ast: rename the mindwm/moutdwm and deinline them
drm/ast: resync the dram post code with upstream
drm/ast: add AST 2400 support.
drm/ast: add widescreen + rb modes from X.org driver (v2)
This is the initial attempt at porting the DP501 code from the userspace
driver,
the firmware file is in
http://people.freedesktop.org/~airlied/ast_dp501_fw.bin
this should really be exposed as another encoder/connector that is cloneable
v0.2:
init 3rd tx properly,
add scratch reduction of VRAM size
backup firmware properly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This resyncs the dram post code with the upstream X.org driver
where ast have improved the code for setting up the dram chips.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This syncs up the mode code from the X.org driver upstream,
and adds the mode validation step for hw that doesn't have
widescreen.
v2: (from Egbert Eich <eich@suse.de)
squash drm/ast: Use correct structure member for mode validation
to avoid bisect regression.
In struct drm_display_mode crtc_hdisplay and crtc_vdisplay are holding
the crtc parameters after mode fixup. For validation we need hdisplay and
vdisplay.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- ring init improvements (Chris)
- vebox2 support (Zhao Yakui)
- more prep work for runtime pm on Baytrail (Imre)
- eDram support for BDW (Ben)
- prep work for userptr support (Chris)
- first parts of the encoder->mode_set callback removal (Daniel)
- 64b reloc fixes (Ben)
- first part of atomic plane updates (Ville)
* tag 'drm-intel-next-2014-05-06' of git://anongit.freedesktop.org/drm-intel: (75 commits)
drm/i915: Remove useless checks from primary enable/disable
drm/i915: Merge LP1+ watermarks in safer way
drm/i915: Make sure computed watermarks never overflow the registers
drm/i915: Add pipe update trace points
drm/i915: Perform primary enable/disable atomically with sprite updates
drm/i915: Make sprite updates atomic
drm/i915: Support 64b relocations
drm/i915: Support 64b execbuf
drm/i915/sdvo: Remove ->mode_set callback
drm/i915/crt: Remove ->mode_set callback
drm/i915/tv: Remove ->mode_set callback
drm/i915/tv: Rip out pipe-disabling nonsense from ->mode_set
drm/i915/tv: De-magic device check
drm/i915/tv: extract set_color_conversion
drm/i915/tv: extract set_tv_mode_timings
drm/i915/dvo: Remove ->mode_set callback
drm/i915: Make encoder->mode_set callbacks optional
drm/i915: Make primary_enabled match the actual hardware state
drm/i915: Move ring_begin to signal()
drm/i915: Virtualize the ringbuffer signal func
...
Since commit 691e6415c8
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Apr 9 09:07:36 2014 +0100
drm/i915: Always use kref tracking for all contexts.
we have contexts everywhere, and so we must be careful to distinguish
fake contexts, which do not have an associated bo, and real ones, which
do. In particular, we now need to be careful not to dereference NULL
pointers.
This is one such example, as the commit highlighted above failed to move
the unpinning of the default ctx object into the real-context-only
branch.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78792
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some platforms have a shared error interrupt, so if FIFO underrun
reporting gets disabled for one pipe/transcoder it gets disabled
for all pipes/transcoders.
When we disable FIFO underrun reporting we check whether the
interrupt was enabled or not. If it wasn't we might have missed
an underrun and we perform one last check right there. Currently
we print a debug message when an underrun is detect using this
mechanism. Promote the message to DRM_ERROR() to match the other
underrun error messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By exporting the ability to map user address and inserting PTEs
representing their backing pages into the GTT, we can exploit UMA in order
to utilize normal application data as a texture source or even as a
render target (depending upon the capabilities of the chipset). This has
a number of uses, with zero-copy downloads to the GPU and efficient
readback making the intermixed streaming of CPU and GPU operations
fairly efficient. This ability has many widespread implications from
faster rendering of client-side software rasterisers (chromium),
mitigation of stalls due to read back (firefox) and to faster pipelining
of texture data (such as pixel buffer objects in GL or data blobs in CL).
v2: Compile with CONFIG_MMU_NOTIFIER
v3: We can sleep while performing invalidate-range, which we can utilise
to drop our page references prior to the kernel manipulating the vma
(for either discard or cloning) and so protect normal users.
v4: Only run the invalidate notifier if the range intercepts the bo.
v5: Prevent userspace from attempting to GTT mmap non-page aligned buffers
v6: Recheck after reacquire mutex for lost mmu.
v7: Fix implicit padding of ioctl struct by rounding to next 64bit boundary.
v8: Fix rebasing error after forwarding porting the back port.
v9: Limit the userptr to page aligned entries. We now expect userspace
to handle all the offset-in-page adjustments itself.
v10: Prevent vma from being copied across fork to avoid issues with cow.
v11: Drop vma behaviour changes -- locking is nigh on impossible.
Use a worker to load user pages to avoid lock inversions.
v12: Use get_task_mm()/mmput() for correct refcounting of mm.
v13: Use a worker to release the mmu_notifier to avoid lock inversion
v14: Decouple mmu_notifier from struct_mutex using a custom mmu_notifer
with its own locking and tree of objects for each mm/mmu_notifier.
v15: Prevent overlapping userptr objects, and invalidate all objects
within the mmu_notifier range
v16: Fix a typo for iterating over multiple objects in the range and
rearrange error path to destroy the mmu_notifier locklessly.
Also close a race between invalidate_range and the get_pages_worker.
v17: Close a race between get_pages_worker/invalidate_range and fresh
allocations of the same userptr range - and notice that
struct_mutex was presumed to be held when during creation it wasn't.
v18: Sigh. Fix the refactor of st_set_pages() to allocate enough memory
for the struct sg_table and to clear it before reporting an error.
v19: Always error out on read-only userptr requests as we don't have the
hardware infrastructure to support them at the moment.
v20: Refuse to implement read-only support until we have the required
infrastructure - but reserve the bit in flags for future use.
v21: use_mm() is not required for get_user_pages(). It is only meant to
be used to fix up the kernel thread's current->mm for use with
copy_user().
v22: Use sg_alloc_table_from_pages for that chunky feeling
v23: Export a function for sanity checking dma-buf rather than encode
userptr details elsewhere, and clean up comments based on
suggestions by Bradley.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Gong, Zhipeng" <zhipeng.gong@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Cc: "Volkin, Bradley D" <bradley.d.volkin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
[danvet: Frob ioctl allocation to pick the next one - will cause a bit
of fuss with create2 apparently, but such are the rules.]
[danvet2: oops, forgot to git add after manual patch application]
[danvet3: Appease sparse.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bit 31 in GEN6_PMINTRMSK is not an interrupt disable bit with gen8.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise, we do a NULL pointer dereference.
I've seen this happen while handling an error in
i915_gem_object_pin_to_display_plane():
If i915_gem_object_set_cache_level() fails, we call is_pin_display()
to handle the error. At this point, the object is still not pinned
to GGTT and maybe not even bound, so we have to check before we
dereference its GGTT vma.
The IGT kms_flip/bo-too-big tests for this bug.
v2: Chris Wilson says restoring the old value is easier, but that
is_pin_display is useful as a theory of operation. Take the solomonic
decision: at least this way is_pin_display is a little more robust
(until Chris can kill it off).
v3: Chris suggests the WARN in i915_gem_obj_to_ggtt has outlived its
usefulness: add a reminder to remove it.
Issue: VIZ-3772
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Testcase: igt/kms_flip/bo-too-big
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looking at our current dsi driver I note that:
- We don't have any slave driver right now.
- There's zero support for the hardware state readout and cross check
code.
- All the modeset state seems to be tracked in the intel_dsi structure
instead of the pipe config.
Given all that I can't properly audit the dsi ->mode_set callback. So
just do it as the first thing in the ->pre_pll_enable hook and hope
for the best.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bit more care required here since there are some very few things
between the call to encoder->mode_set and encoder->pre_enable. But
they're either book-keeping or only matter for the vga port on the
pch. So of no concern.
Note that with the new sequence we write the infoframes after
selecting the clock source, but that shouldn't matter. I've simply
opted for this to have simpler code.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the hard work was already done, only thing left to do is remove
the empty callback. And a now rather misleading comment I've spotted
while reading through code.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to dp the only thing we do is call intel_write_eld and prepare
a bit of state for the enable hooks. The only difference is that we
write that to the hardware instead of keeping track of it somewhere in
software.
Still we can just move all this to the very first enable hook.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those functions are only used on vlv platforms, so no need to check.
Especially if we're not too consistent about it.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With all the preceding refactoring the dp mode_set callback only
computes a bit of state (all derived from the pipe config) and also
writes the eld. As long as we do that before we enable the audio bit
or depend upon the correct value in intel_dp->DP we'll be fine.
No other hw state is touched.
We therefore only need to check that clearing intel_dp->DP is save.
Which it is since when we re-enable we already mask out all the bits
the link training code sets. And we need to keep on doing that so that
the re-train loop walking over pre-emph/voltage-swing values still
works properly.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only ilk/snb/ivb need the port A pll setup, so move it to the
pre_enable hook for those platforms. We can savely do this since on
those platforms there's nothing that touches the hardware between the
encoder->mode_set and the encoder->pre_enable calls.
Also add a comment that port A is ilk+ only.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Including state readout and cross-checking. This allows us to get rid
of crtc->eld_vld on hsw+. It also means that fastboot will be unhappy
if the BIOS hasn't set up the audio routing like we want it too.
Wrt fastboot and external screens I see a few options:
- Don't.
- Try to fix up eld, infoframes and audio settings after the fact. But
that means some pretty extensive reworking of our code which
currently does all this while the pipe/port is still off.
I won't bother with converting SDVO over to this because the audio
support for SDVO is very lacking:
- We don't update the eld.
- We don't update the audio state on the sdvo encoder.
- We don't check whether the platform can even feed audio to the sdvo
encoder.
I've converted hdmi, dp & ddi all in one go since ddi needs both hdmi
and dp converted and so doing it step-by-step would have required a
few intermediate hacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's no need to check whether audio is enabled (which for ddi ports
is done through the crtc->eld_vld flag) since at the cost of a
potentially unecessary register rmw cycle we can unconditionally do
this.
Note that the edp check is just paranoia since we won't ever call the
write_eld function for an edp panel.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we can rely on the state cross-checker to have a bit
assurance that we'll get it right.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on those platforms which have a simple bit and don't rely
on the fully programmable CSC unit to do this.
Note that with the current code this includes CHV, but I guess that
platform will match BYT.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We in the pre_enable hook we should only rely on the pipe config and
not on some other state set through properties or detect functions.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also add state readout and cross-check support. The only invasive change
is wiring up the new flag to the ->set_infoframes callbacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For compliance we really should be sending NULL infoframes always
when we detect a hdmi capable monitor. Also remove the now redudant
setting for the has_audio case and enforce that audio is only
possible with a hdmi sink.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Update pull request with drm core patches. Mostly some polish for the
primary plane stuff and a pile of patches all over from Thierry. Has
survived a few days in drm-intel-nightly without causing ill.
I've frobbed my scripts a bit to also tag my topic branches so that you
have something stable to pull - I've accidentally pushed a bunch more
patches onto this branch before you've taken the old pull request.
* tag 'topic/core-stuff-2014-05-05' of git://anongit.freedesktop.org/drm-intel:
drm: Make drm_crtc_helper_disable() return void
drm: Fix indentation of closing brace
drm/dp: Fix typo in comment
drm: Fixup flip-work kerneldoc
drm/fb: Fix typos
drm/edid: Cleanup kerneldoc
drm/edid: Drop revision argument for drm_mode_std()
drm: Try to acquire modeset lock on panic or sysrq
drm: remove unused argument from drm_open_helper
drm: Handle ->disable_plane failures correctly
drm: Simplify fb refcounting rules around ->update_plane
drm/crtc-helper: gc usless connector loop in disable_unused_functions
drm/plane_helper: don't disable plane in destroy function
drm/plane-helper: Fix primary plane scaling check
drm: make mode_valid callback optional
drm/edid: Fill PAR in AVI infoframe based on CEA mode list
Everything should be in place so enable rc6/rps for bdw.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
by correctly displaying result and requested.
Suggested-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In BDW, Apart from unmasking up/down threshold interrupts. we need
to umask bit 32 of PM_INTRMASK to route interrupts to target via Display
Interface.
v2: Add (1<<31) mask (Ville)
v3: Add Gen check for the mask (ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Almost all of it is reusable from the existing code. The primary
difference is we need to do even less in the interrupt handler, since
interrupts are not shared in the same way.
The patch is mostly a copy-paste of the existing snb+ code, with updates
to the relevant parts requiring changes to the interrupt handling. As
such it /should/ be relatively trivial. It's highly likely that I missed
some places where I need a gen8 version of the PM interrupts, but it has
become invisible to me by now.
This patch could probably be split into adding the new functions,
followed by actually handling the interrupts. Since the code is
currently disabled (and broken) I think the patch stands better by
itself.
v2: Move the commit about not touching the ringbuffer interrupt to the
snb_* function where it belongs (Rodrigo)
v3: Rebased on Paulo's runtime PM changes
v4: Not well validated, but rebase on
commit 730488b2ed
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Mar 7 20:12:32 2014 -0300
drm/i915: kill dev_priv->pm.regsave
v5: Rebased on latest code base. (Deepak)
v6: Remove conflict markers, Unnecessary empty line and use right
IIR interrupt (Ville)
v7: mask modified without rmw (Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we dont have semaphores enabled, we allocate 4
dwords for signalling. But end up emitting more regardless.
Fix this by bailing out early if semaphores are not enabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78274
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78283
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added as generic parameters which will be initialized in the panel
driver and are specific to panels.
Backlight delays have also kept as placeholders and will be used used
once we have MIPI backlight enabling support
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In VBT fields operation mode is 0 for Video mode and 1 for command mode.
This field will be directly used as is in generic panel driver. So
adjust accordingly.
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SNB the BIOS provided WM memory latency values seem insufficient to
handle high resolution displays.
In this particular case the display mode was a 2560x1440@60Hz, which
makes the pixel clock 241.5 MHz. It was empirically found that a memory
latency value if 1.2 usec is enough to avoid underruns, whereas the BIOS
provided value of 0.7 usec was clearly too low. Incidentally 1.2 usec
is what the typical BIOS provided values are on IVB systems.
Increase the WM memory latency values to at least 1.2 usec on SNB.
Hopefully this won't have a significant effect on power consumption.
v2: Increase the latency values regardless of the pixel clock
Cc: Robert N <crshman@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70254
Tested-by: Robert Navarro <crshman@gmail.com>
Tested-by: Vitaly Minko <vitaly.minko@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we set backlight on behalf of ACPI opregion, we will convert the
backlight value in the 0-255 range defined in opregion to the actual
hardware level. Commit 22505b82a2 (drm/i915: avoid brightness overflow
when doing scale) is meant to fix the overflow problem when doing the
conversion, but it also caused a problem that the converted hardware
level doesn't quite represent the intended value: say user wants maximum
backlight level(255 in opregion's range), then we will calculate the
actual hardware level to be: level = freq / max * level, where freq is
the hardware's max backlight level(937 on an user's box), and max and
level are all 255. The converted value should be 937 but the above
calculation will yield 765.
To fix this issue, just use 64 bits to do the calculation to keep the
precision and avoid overflow at the same time.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=72491
Reported-by: Nico Schottelius <nico-bugzilla.kernel.org@schottelius.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This matches the algorithm used by earlier kernels when selecting the
mode for the fbcon. And only if there is no modes at all, do we fall
back to using the BIOS configuration. Seamless transition is still
preserved (from the BIOS configuration to ours) so long as the BIOS has
also chosen what we hope is the native configuration.
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78655
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[Jani: applied Chris' "Please imagine that I wrote this correctly."]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There are certain BDW high res eDP machines that regressed due to
commit 38aecea0cc
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Mar 3 11:18:10 2014 +0100
drm/i915: reverse dp link param selection, prefer fast over wide again
The commit lead to 2 lanes at 5.4 Gbps being used instead of 4 lanes at
2.7 Gbps on the affected machines. Link training succeeded for both, but
the screen remained blank with the former config. Further investigation
showed that 4 lanes at 5.4 Gbps worked also.
The root cause for the blank screen using 2 lanes remains unknown, but
apparently the driver for a certain other operating system by default
uses the max available lanes. Follow suit on Broadwell eDP, for at least
until we figure out what is going on.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76711
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Tested-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
These are generated with intel-gpu-tools/tools/null_state_gen
v2: Don't use header file for states (Daniel Vetter)
v3: Proper URB state size for gen8/GT3 (Damien Lespiau)
Tested-by: Kristen Carlson Accardi <kristen@linux.intel.com> (v1)
Tested-by: Oscar Mateo <oscar.mateo@intel.com> (v2)
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HW guys say that it is not a cool idea to let device
go into rc6 without proper 3d pipeline state.
For each new uninitialized context, generate a
valid null render state to be run on context
creation.
This patch introduces a skeleton with empty states.
v2: - No need to vmap (Chris Wilson)
- use .c files for state (Daniel Vetter)
- no need to flush as i915_add_request does it
- remove parameter for batch alloc size
- don't wait for the init (Ben Widawsky)
v3: - move to cpu/gpu (Chris Wilson)
Tested-by: Kristen Carlson Accardi <kristen@linux.intel.com> (v1)
Tested-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we end up tearing down fences when e.g. the client quits
way too early. Might or might not fix a fence pin_count BUG Ville has
reported.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Userspace can currently provoke this when e.g. trying to use a pinned
scanout as a cursor or overlay target. Later on that might lead to
some fun fence pin count mayhem.
Spurred by Ville's report that something goes wrong here and
originally I've thought that this might slip through the pwrite gtt
fastpath. But that one checks of obj tiling, so should be ok.
But one thing that _does_ blow up is the vma unbinding with more than
one address space. The next patch will fix this.
v2: Use a WARN_ON - Chris pointed out that we already catch all cases
so userspace can't provoke this like I've originally feared.
While reviewing relevant code I've noticed a pile of DRM_ERROR in the
overlay&cursor code which are all triggerable by userspace. Tune them
down while at it.
v3: Split out the DRM_ERROR->DRM_DEBUG_KMS change into a separate patch,
as requested by Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During initial probing of the modes to assign to the fbdev console, we
use the CRTC and connector ids. These are much harder for us to
understand than if we used their actual names (or pipe in the CRTC
case). Similarly, we want to manually print the mode size rather than
rely on mode->name being set.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Patch done using the following semantic patch (thanks Daniel for the
help!)
@@
iterator name list_for_each_entry;
iterator name for_each_crtc;
struct drm_crtc * crtc;
struct drm_device * dev;
@@
-list_for_each_entry(crtc,&dev->mode_config.crtc_list, head) {
+for_each_crtc(dev,crtc) {
...
}
Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Generated using the semantic patch:
@@
iterator name list_for_each_entry;
iterator name for_each_intel_crtc;
struct intel_crtc * crtc;
struct drm_device * dev;
@@
-list_for_each_entry(crtc,&dev->mode_config.crtc_list,...) {
+for_each_intel_crtc(dev,crtc) {
...
}
Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fed up with having that long list_for_each_entry() invocation?
Use for_each_intel_crtc()!
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Squash in patch that exported ilk_wm_max_level.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That's not necessary and makes the code not as neat as it could be.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow UXA submits a completely bogus DR4 value since essentially
forever. It was originally introduced in
commit bade7d7d2505a10a8a7d24b084aff9742e2d6d64
Author: Eric Anholt <eric@anholt.net>
Date: Fri Jun 6 14:03:25 2008 -0700
Use the DRM for submitting batchbuffers when available.
and dutifully copied around ever since. Since we want to keep the
general dirt catching around just special case the UXA value.
This regression was introduced in
commit 9cb346648d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Apr 24 08:09:11 2014 +0200
drm/i915: Catch dirt in unused execbuffer fields
Comment from Chris' review:
"To be fair, it is a sensible value if one supposes a Region style API to
cliprects. Under that API, DR[14] define the extents of the clip region,
and ((0,0), (0,0)) [DR1==DR4==0] would mean all clipped, do not draw
anything."
v2: Pimp commit message a bit and remove the double space.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78494
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jörg Otte <jrg.otte@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The fence pin count should always be <= the bo pin count. If that's
not the case then we have a funny problem and are leaking references
somewhere.
Which means we can catch fence pin leaks by checking for the same
upper limit as we do for the bo pin count. Inspired by a discussion
with Ville about a fence leak igt testcase.
v2: Also check for fence->pin_count <= ggtt_vma->pin_count, since that
might catch a leak even quicker. Also de-inline them, they're getting
too big.
v3: Don't separately check for MAX_PIN_COUNT since the > vma->pin_count
check will catch that already (Chris).
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe might not start to actually run until the port has been enabled
(depends on the platform and port type). So don't try to wait for vblank
after we enabled the pipe but haven't yet enabled the port.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=77297
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already moved the plane disable/enable to happen as the first/last
thing on every other platforms. Follow suit with gmch platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Frob drm_vblank_on conflict, as usual.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is missing in:
commit 78325f2d27
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Tue Apr 29 14:52:29 2014 -0700
drm/i915: Virtualize the ringbuffer signal func
Looks to me like a rebase side-effect...
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV uses the same bits as SNB/VLV to code the Graphics Mode Select field
(GFX stolen memory size) with the addition of finer granularity modes:
4MB increments from 0x11 (8MB) to 0x1d.
Values strictly above 0x1d are either reserved or not supported.
v2: 4MB increments, not 8MB. 32MB has been omitted from the list of new
values (Ville Syrjälä)
v3: Also correctly interpret GGMS (GTT Graphics Memory Size) (Ville
Syrjälä)
v4: Don't assign a value that needs 20bits or more to a u16 (Rafael
Barbalho)
[vsyrjala: v5: Split the early quirks to another patch]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Tested-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No CRT output on CHV, so don't call intel_crt_init().
v2: Don't disable CRT on HAS.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add chv_crtc_clock_get() to read out the DPLL settings.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Fix compile due to bikeshedded headers in an earlier patch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With additional of pipe C, current 1 bit registers for pipe select
for HDMI and DP are no longer able to gather for 3 pipes. As a result,
new bits location in the same registers are added.
For HDMI, VLV uses bit 30, CHV uses bit 24-25.
For DP, VLV uses bit 30, CHV uses bit 16-17.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added programming phy layer for CHV based on "Application note for 1273
CHV Display phy".
v2: Rebase the code and do some cleanup.
v3: Rework based on Ville review.
-Fix the macro where the ch info need to swap, and add parens to ?
operator.
-Fix wrong bit define for DPIO_PCS_SWING_CALC_0 and
DPIO_PCS_SWING_CALC_1 and rename for meaningful.
-Add some comments for CHV specific DPIO registers.
-Change the dp margin registery value to decimal to align with the
doc.
-Fix the not clearing some value in vlv_dpio_read before write again.
-Create new hdmi/dp encoder function for chv instead of share with
valleyview.
v4: Rebase the code after rename the DPIO registers define and upstream
change.
Based on Ville review.
-For unique transition scale selection, after Ville point out, look
like the doc might wrong for the bit 26. Use bit 27 for ch0 and
ch1.
-Break up some dpio write value into two/three steps for readability.
-Remove unrelated change.
-Add some shift define for some registers instead just give the hex
value.
-Fix a bug where write to wrong VLV_TX_DW3.
v5: Based on Ville review.
- Move tx lane latency optimal setting from chv_dp_pre_pll_enable to
chv_pre_enable_dp, and chv_hdmi_pre_pll_enable to
chv_hdmi_pre_enable respectively.
- Fix typo in one margin_reg_value for DP_TRAIN_VOLTAGE_SWING_400.
- Clear DPIO_TX_UNIQ_TRANS_SCALE_EN for DP and HDMI.
- Mask the old deemph and swing bits for hdmi.
v6: Remove stub for pre_pll_enable for dp and hdmi.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[vsyrjala: Don't touch panel power sequencing on DP]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added programming PLL for CHV based on "Application note for 1273 CHV
Display phy".
v2: -Break the common lane reset into another patch.
-Break the clock calculation into another patch.
-The changes are based on Ville review.
-Rework based on DPIO register define naming convention change.
-Break the dpio write into few lines to improve readability.
-Correct the udelay during chv_enable_pll.
-clean up some magic numbers with some new define.
-program the afc recal bit which was missed.
v3: Based on Ville review
- minor correction of the bit defination
- add deassert/propagate data lane reset
v4: Corrected the udelay between dclkp enable and pll enable.
Minor comment and better way to clear the TX lane reset.
v5: Squash in fixup from Rafael Barbalho.
[vsyrjala: v6: Polish the defines (Imre)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the chv clock limit, find the best divisor.
The divisor data has been verified with this spreadsheet.
P1273_DPLL_Programming Spreadsheet.
v2: Rebase the code and change the chv_find_best_dpll based on new
standard way to use intel_PLL_is_valid. Besides, clean up some extra
variables.
v3: Ville suggest better fixed point for m2 calculation.
v4: -Add comment for the limit is compute using fast clock. (Ville)
-Don't pass the request clock to chv_clock, as the same function will
be use clock readout, which doens't have request clock. (Ville)
-Add and use DIV_ROUND_CLOSEST_ULL to consistent with other clock
calculation. (Ville)
-Fix the dp m2 after m2 has stored fixed point. (Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Avoid div-by-zero in chv_clock()]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During cold boot, the display controller needs to deassert the common
lane reset. Only do it once during intel_init_dpio for both PHYx2 and
PHYx1.
Besides, assert the common lane reset when disable pll. This still
to be determined whether need to do it by driver.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
[vsyrjala: Don't disable DPIO PLL when using DSI]
[vsyrjala: Don't call vlv_disable_pll() by accident on CHV]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Move part of a moved comment back as suggested by Imre since
it's valid for both byt and chv.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cherryview has 3 pipes. Some of the pll dpio offset calculation is
based on pipe number. Need to use vlv_pipe_to_channel to calculate the
correct phy channel to use for the pipe.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The additional DPLL registers added to support Port D. Besides, add
some new PHY control and status registers based on B-spec.
v2: Based on Ville review
- Corrected DPIO_PHY_STATUS offset and name.
- Rebase based on upstream change after introduce enum dpio_phy and
enum dpio_channel.
v3: Rebased on top of Antti's 3-pipe prep patch. Note that the new offsets for
the DPLL registers aren't in place yet, so this introduces a slight regression.
But since 3 pipe support isn't fully enabled yet anyaway in -internal this
shouldn't matter too much.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has 2 display phys. First phy (IOSF offset 0x1A) has two channels,
and second phy (IOSF offset 0x12) has single channel. The first phy is
used for port B and port C, while second phy is only for port D.
v2: Move the pipe to determine which phy to select for
vlv_dpio_read/vlv_dpio_write to another patch. (Daniel)
v3: Rebase the code based on rework on how to calculate DPIO offset.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fill in the sprite bits for DDL1/DDL2 registers, and add DDL3.
Still need to write the code to use these...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Update to also fill in the new num_pipes field.
v3: Rebase on top of the pciid extraction.
v4: Switch from info->has*ring to info->ring mask. Also add VEBOX support whiel
at it.
v5: s/CHV_PCI_IDS/CHV_IDS/, and drop the trailing '\'
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV clock gating isn't identical to VLV, so add a new function
for it. This is only a start, and further changes are needed as
the details become available.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make i915_gem_interrupt debugfs file functional on CHV.
FIXME: Extract helpers for gt/display blocks to shrink the function a
bit and avoid duplication between bdw/chv (and other similar cases for
upstream).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Inspired by a review bikeshed from Jani.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has the Gen8 master interrupt register, as well as Gen8
GT/PCU interrupt registers.
The display block is based on VLV, with the main difference
of adding pipe C.
v2: Rewrite the order of operations to make more sense
Don't bail out if MASTER_CTL register doesn't show an interrupt,
as display interrupts aren't reported there.
v3: Rebase on top of Egbert Eich's hpd irq handling rework by using
the relevant port hotplug logic like for vlv.
v4: Rebase on top of Ben's gt irq #define refactoring.
v5: Squash in gen8_gt_irq_handler refactoring from Zhao Yakui
<yakui.zhao@intel.com>
v6: Adapt to upstream changes, dev_priv->irq_received is gone.
v7: Enable 3 the commented-out 3 pipe support.
v8: Rebase on top of Paulo's irq setup rework, use the renamed macros from
upstream.
v9: Grab irq_lock around i915_enable_pipestat()
FIXME: There's probably some potential for more shared code between bdw and chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop the unnecessary cast Jani spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For clients that submit large batch buffers the command parser has
a substantial impact on performance. On my HSW ULT system performance
drops as much as ~20% on some tests. Most of the time is spent in the
command lookup code. Converting that from the current naive search to
a hash table lookup reduces the performance drop to ~10%.
The choice of value for I915_CMD_HASH_ORDER allows all commands
currently used in the parser tables to hash to their own bucket (except
for one collision on the render ring). The tradeoff is that it wastes
memory. Because the opcodes for the commands in the tables are not
particularly well distributed, reducing the order still leaves many
buckets empty. The increased collisions don't seem to have a huge
impact on the performance gain, but for now anyhow, the parser trades
memory for performance.
NB: Ville noticed that the error paths through the ring init code
will leak memory. I've not addressed that here. We can do a follow
up pass to handle all of the leaks.
v2: improved comment describing selection of hash key mask (Damien)
replace a BUG_ON() with an error return (Tvrtko, Ville)
commit message improvements
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the same code for enabling/disabling planes on all platforms. Rename
the functions to reflect that they're no longer specific to any
platform.
For now we leave the plane enable/disable to ccur at the same old
position in the modeset sequence.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Frob drm_vblank_on conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Media force wake get hangs the machine when the system is booted without
displays attached. The assumption is that (at least some versions of)
the firmware has skipped some initialization in that case.
Empirical evidence suggests we need to reset the media force wake
request register in addition to the render one to avoid hangs.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=75895
Reported-by: Imre Deak <imre.deak@intel.com>
Reported-by: Darren Hart <dvhart@linux.intel.com>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
During the review of
commit 1f70999f90
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Jan 27 22:43:07 2014 +0000
drm/i915: Prevent recursion by retiring requests when the ring is full
Ville raised the point that our interaction with request->tail was
likely to foul up other uses elsewhere (such as hang check comparing
ACTHD against requests).
However, we also need to restore the implicit retire requests that certain
test cases depend upon (e.g. igt/gem_exec_lut_handle), this raises the
spectre that the ppgtt will randomly call i915_gpu_idle() and recurse
back into intel_ring_begin().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78023
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
[danvet: Remove now unused 'tail' variable as spotted by Brad.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A few improvements to the fallback method for waiting upon ring space:
1. Fix the start/end wait tracepoints to always be paired.
2. Increase responsiveness of checking
3. Mark the process as waiting upon io
4. Check for signal interruptions
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
[danvet: Drop the s/msleep/io_schedule_timeout/ change again since the
latter isn't exported.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When linking the i2c sysfs file into the connector's directory
pass directory and link target in the right order.
This code was introduced with:
commit 931c1c2698
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Feb 11 17:12:51 2014 +0200
drm/i915: sdvo: add i2c sysfs symlink to the connector's directory
This is the same what we do for DP connectors, so make things more
consistent.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Most likely the minimums for both should be enough for enabling the
native resolution on the eDP, and we'll end up using the predetermined
optimal link config for the panel.
v2: Add debug prints.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73539
Tested-by: Markus Blank-Burian <burian@muenster.de>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use defines, do not set anything if VBT has values unknown to us.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Even if the panel claims it can support 4 lanes, there's the
possibility that the HW can't, so consider this while selecting the
max lane count.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There is a good debate to be had about how best to fit the aliasing
PPGTT into the code. However, as it stands right now, getting aliasing
PPGTT bindings is a hack, and done through implicit arguments. To make
this absolutely clear, WARN and return an error if a driver writer tries
to do something they shouldn't.
I have no issue with an eventual revert of this patch. It makes sense
for what we have today.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It was always the intention to do the topdown allocation for context
objects (Chris' idea originally). Unfortunately, I never managed to land
the patch, but someone else did, so now we can use it.
As a reminder, hardware contexts never need to be in the precious GTT
aperture space - which is what is what happens with the normal bottom up
allocation we do today. Doing a top down allocation increases the odds
that the HW contexts can get out of the way, especially with per FD
contexts as is done in full PPGTT
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add runtime PM support for VLV, but leave it disabled. The next patch
enables it.
The suspend/resume sequence used is based on [1] and [2]. In practice we
depend on the GT RC6 mechanism to save the HW context depending on the
render and media power wells. By the time we run the runtime suspend
callback the display side is also off and the HW context for that is
managed by the display power domain framework.
Besides the above there are Gunit registers that depend on a system-wide
power well. This power well goes off once the device enters any of the
S0i[R123] states. To handle this scenario, save/restore these Gunit
registers. Note that this is not the complete register set dictated by
[2], to remove some overhead, registers that are known not to be used are
ignored. Also some registers are fully setup by initialization functions
called during resume, these are not saved either. The list of registers
can be further reduced, see the TODO note in the code.
[1] VLV_gfx_clocking_PM_reset_y12w21d3 / "Driver D3 entry/exit"
[2] VLV2_S0IXRegs
v2:
- unchanged
v3:
- fix s/GEN6_PMIIR/GEN6_PMIMR/ typo when saving/restoring registers
(Ville)
v4:
- rebased on the previous patch fixing GEN register prefixes
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[ rebased (according to v4) ]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, none of the RPM callbacks can fail, but the next patch adding
RPM support for VLV changes this, so prepare for it.
In case one of these callbacks return error RPM will get permanently
disabled until the error is explicitly cleared. In the future we could
add support for re-enabling it, for example after resetting the HW, but
for now - hopefully - we can live with the simpler solution.
v2:
- propagate the error from the resume callbacks too (Paulo)
v3:
- fix rebase fail typo around IS_GEN6() check in intel_runtime_suspend()
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needed by the VLV S0ix context save/restore helpers.
v2:
- unchanged
v3:
- use proper GEN register prefixes (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
nouveau fixes.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/gm107/gr: bump attrib cb size quite a bit
drm/nouveau: fix another lock unbalance in nouveau_crtc_page_flip
drm/nouveau/bios: fix shadowing from PROM on big-endian systems
drm/nouveau/acpi: allow non-optimus setups to load vbios from acpi
Some more i915 fixes. There's still some DP issues we are looking into,
but wanted to get these moving.
* tag 'topc/core-stuff-2014-05-05' of git://anongit.freedesktop.org/drm-intel:
drm/i915: don't try DP_LINK_BW_5_4 on HSW ULX
drm/i915: Sanitize the enable_ppgtt module option once
drm/i915: Break encoder->crtc link separately in intel_sanitize_crtc()
Due to Pipe C DPINVGTT has more bits on CHV.
v2: Fix comment to say VLV/CHV (Rafael)
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebase on top of Ben's GT interrupt shuffling.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has pipe C and PSR which cause changes to DPFLIPSTAT.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FIXME: We probably want to sprinkle _CHV suffixes over these.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enable aliasing PPGTT for CHV, but keep full PPGTT still disabled until
it gets enabled for BDW.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Page table updates were getting stuck in the CPU cache on chv causing
spurious page faults and strange behaviour.
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: Add !HAS_LLC checks]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ignore the cache bits in PPAT and just set the snoop bit where
appropriate. BDW WB is mapped to snooped access, while all other
modes are mapped to non-snooped access.
The hardware supposedly ignores everything except the snoop bit
in the PPAT entries.
Additionally the hardware actually enforces snooping for all
page table accesses, and thus the snoop bit is ignored for PDEs.
v2: Rebased on top of the bdw resume fix to reload the ppat entries.
v3: Rebase on top of the i915_gem_gtt.h header extraction.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VCE 2.0 just like the other CIK parts.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Uses the same code as Kabini.
Signed-off-by: Samuel Li <samuel.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
- Use vddc/sclk dep table for voltage if available
- Fix UVD DPM setup
- Patch voltage tables properly for non-UVD blocks
- Fix DPM + UVD/VCE on Mullins
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Generic dpm support similar to Kabini. Mullins specific features
will be worked on later.
Signed-off-by: Samuel Li <samuel.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Has same version of UVD as other CIK parts.
Signed-off-by: Samuel Li <samuel.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Also add golden registers, update firmware loading functions.
Signed-off-by: Samuel Li <samuel.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Mullins is a new CI-based APU.
Signed-off-by: Samuel Li <samuel.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
It would appear this bug has been copy/pasted many times without being noticed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The way the tile mode array index was calculated only makes sense for
the CIK specific macrotile mode array. For SI, we need to use one of the
tile mode array indices reserved for displayable surfaces.
This happened to result in correct display most if not all of the time
because most of the SI tiling modes use the same number of banks.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
We won't be calling intel_enable_primary_plane() or
intel_disable_primary_plane() with the primary plane in the
wrong state. So remove the useless DISPLAY_PLANE_ENABLE checks.
v2: Convert the checks to WARNs instead (Daniel,Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On ILK when we disable a particular watermark level, we must
maintain the actual watermark values for that level for some time
(until the next vblank possibly). Otherwise we risk underruns.
In order to achieve that result we must merge the LP1+ watermarks a
bit differently since we must also merge levels that are to be
disabled. We must also make sure we don't overflow the fields in the
watermark registers in case the calculated watermarks come out too
big to fit.
As early as possbile we mark all computed watermark levels as
disabled if they would exceed the register maximums. We make sure
to leave the actual watermarks for such levels zeroed out. Then during
merging, we take the maxium values for every level, regardless if
they're disabled or not. That may seem a bit pointless since at the
moment all the watermark levels we merge should have their values
zeroed if the level is already disabled. However soon we will be
dealing with intermediate watermarks that, in addition to the new
watermark values, also contain the previous watermark values, and so
levels that are disabled may no longer be zeroed out.
v2: Split the patch in two (Paulo)
Use if() instead of & when merging ->enable (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix commit message as noted by Paulo.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we calculate the watermarks for a pipe make sure we leave any
level fully zeroed out if it would exceed any of the maximum values
that fit in the registers.
This will be important later when we start to use also disabled
watermark levels during LP1+ merging.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add trace points for observing the atomic pipe update mechanism.
v2: Rebased due to earlier changes
v3: Pass intel_crtc instead of drm_crtc (Daniel)
v4: Pass frame counter from the caller to evaded/end since
the caller now always has that ready
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the primary plane enable/disable to occur atomically with the
sprite update that caused the primary plane visibility to change.
FBC and IPS enable/disable is left to happen well before or after
the primary plane change.
v2: Pass intel_crtc instead of drm_crtc (Daniel)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a mechanism by which we can evade the leading edge of vblank. This
guarantees that no two sprite register writes will straddle on either
side of the vblank start, and that means all the writes will be latched
together in one atomic operation.
We do the vblank evade by checking the scanline counter, and if it's too
close to the start of vblank (too close has been hardcoded to 100usec
for now), we will wait for the vblank start to pass. In order to
eliminate random delayes from the rest of the system, we operate with
interrupts disabled, except when waiting for the vblank obviously.
Note that we now go digging through pipe_to_crtc_mapping[] in the
vblank interrupt handler, which is a bit dangerous since we set up
interrupts before the crtcs. However in this case since it's the vblank
interrupt, we don't actually unmask it until some piece of code
requests it.
v2: preempt_check_resched() calls after local_irq_enable() (Jesse)
Hook up the vblank irq stuff on BDW as well
v3: Pass intel_crtc instead of drm_crtc (Daniel)
Warn if crtc.mutex isn't locked (Daniel)
Add an explicit compiler barrier and document the barriers (Daniel)
Note the irq vs. modeset setup madness in the commit message (Daniel)
v4: Use prepare_to_wait() & co. directly and eliminate vbl_received
v5: Refactor intel_pipe_handle_vblank() vs. drm_handle_vblank() (Chris)
Check for min/max scanline <= 0 (Chris)
Don't call intel_pipe_update_end() if start failed totally (Chris)
Check that the vblank counters match on both sides of the critical
section (Chris)
v6: Fix atomic update for interlaced modes
v7: Reorder code for better readability (Chris)
v8: Drop preempt_check_resched(). It's not available to modules
anymore and isn't even needed unless we ourselves cause
a wakeup needing reschedule while interrupts are off
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the rest of the code to enable this is in my branch. Without my
branch, hitting > 32b offsets is impossible. The code has always
"supported" 64b, but it's never actually been run of tested. This change
doesn't actually fix anything. [1] I am not sure why X won't work yet. I
do not get hangs or obvious errors.
There are 3 fixes grouped together here. First is to remove the
hardcoded 0 for the upper dword of the relocation. The next fix is to
use a 64b value for target_offset. The final fix is to not directly
apply target_offset to reloc->delta. reloc->delta is part of ABI, and so
we cannot change it. As it stands, 32b is enough to represent everything
we're interested in representing anyway. The main problem is, we cannot
add greater than 32b values to it directly.
[1] Almost all of intel-gpu-tools is not yet ready to test 64b
relocations. There are a few places that expect 32b values for offsets
and these all won't work.
Cc: Rafael Barbalho <rafael.barbalho@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously, our code only had a 32b offset value for where the
batchbuffer starts. With full PPGTT, and 64b canonical GPU address
space, that is an insufficient value. The code to expand is pretty
straight forward, and only one platform needs to do anything with the
extra bits.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SDVO is used by both crtcs using the i9xx_ and the ironlake_
functions. For both cases there is nothing between the
encoder->mode_set and the encoder->pre_enable calls that touches the
hardware.
The vlv_ functions are different since they enable the pll before the
->pre_enable hook. But SDVO isn't supported on vlv platforms, so this
doesn't matter.
We've also already clean up all the sdvo state computation logic, all
relevant parts are already in the ->compute_config hook. So we can
just get rid of the ->mode_set hook by converting it to a ->pre_enable
hook.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only set a few bits in the ADPA register, which we then read back
in the enable/disable hooks. So we can just move that bit of state
computation code to the place where we need it since setting these
bits without enabling the CRT encoder has no effects.
The only exceptions are the hotplug bits since they affect the hotplug
detection logic, but we already set those in the ->reset function and
then never touch them.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently for the i9xx crtc hooks there's nothing between the call to
encoder->mode_set and encoder->pre_enable which touches the hardware.
Therefore, since tv is only used on gen3/4, we can just move the hook.
Yay for easy cases!
The only other important thing to check is that the new
->pre_enable hook is idempotent wrt the sw state since now it can
be called multiple times (due to DPMS). After a the bit of refactoring
this is now easy to check: It only reads crtc->config and computes
derived state but otherwise leaves it as-is, so we're good.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe and plane _are_ disabled when we call this. So replace it
all with the corresponding assert (as self-documenting code) and
rip out all the lore.
Checking for a disabled plane would require us to export those macros
from intel_display.c, but if the pipe is off the plane isn't working
either. So this single check is good enough.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only support TV-out on gen3/4 mobile platforms, and i915gm is the
only one that matches.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently for the i9xx crtc hooks there's nothing between the call to
encoder->mode_set and encoder->pre_enable which touches the hardware.
Therefore, since dvo is only used on gen2, we can just move the hook.
Yay for easy cases!
The only other important thing to check is that the new
->pre_enable hook is idempotent wrt the sw state since now it can be
called multiple times (due to DPMS). It only reads crtc->config but
otherwise leaves it as-is, so we're good.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For a bunch of reasons we want to move away from the ->mode_set
callbacks: All hw state setup needs to move into ->enable hooks (so
that DOMS can do runtime pm) and all the configuration setup needs to
move into the compute_config functions.
To start with this make the enocer->mode_set callback optional.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BIOS can enable a pipe but leave the primary plane disabled. This
coflicts with out current idea of primary_enabled. Read the actual
hardware plane state and set primary_enabled appropriately.
We currently assume that primary_enabled is always true when we're about
to disable a crtc. That needs to change now as the plane may not be
enabled. So replace the relevant WARNs with early returns in
intel_{enable,disable}_primary_hw_plane().
Fixes the following warning
[ 3.831602] WARNING: CPU: 0 PID: 1112 at linux/drivers/gpu/drm/i915/intel_display.c:1918 intel_disable_primary_hw_plane+0xe4/0xf0 [i915]()
which got introduced here by me:
commit e9e39655c0c30cddc3f8c09a757678a24dd36737
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Apr 28 15:53:25 2014 +0300
drm/i915: Remove useless checks from primary enable/disable
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add_request has always contained both the semaphore mailbox updates as
well as the breadcrumb writes. Since the semaphore signal is the one
which actually knows about the number of dwords it needs to emit to the
ring, we move the ring_begin to that function. This allows us to remove
the hideously shared #define
On a related not, gen8 will use a different number of dwords for
semaphores, but not for add request.
v2: Make number of dwords an explicit part of signalling (via function
argument). (Chris)
v3: very slight comment change
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This abstraction again is in preparation for gen8. Gen8 will bring new
semantics for doing this operation.
While here, make the writes of MI_NOOPs explicit for non-existent rings.
This should have been implicit before.
NOTE: This is going to be removed in a few patches.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be helpful in abstracting some of the code in preparation for
gen8 semaphores.
v2: Move mbox stuff to a separate struct
v3: Rebased over VCS2 work
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During the initial power well enabling on the driver init/resume path
we can avoid initialzing part of the HW/SW state that will be
initialized anyway by the subsequent init/resume code. For some steps
like HPD initialization this redundancy is not only an overhead but an
actual problem, since they can't be run this early in the overall init
sequence.
Add a flag marking the init phase and skip reinitialzing state that is
not strictly necessary based on that.
This is also needed by the upcoming HPD init restructuring by Thierry
and Daniel.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In commit 691e6415c8
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Apr 9 09:07:36 2014 +0100
drm/i915: Always use kref tracking for all contexts.
we populated fake contexts on all platforms. These were identical to the
full hardware context tracking structs, except for the ctx->obj used to
store the hardware state. However, there remained one place where we
assumed that if a context existed, it would have an object associated
with it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77717
Testcase: igt/drv_suspend/debugfs-reader
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a new function intel_get_crtc_scanline() that returns the current
scanline counter for the crtc.
v2: Rebase after vblank timestamp changes.
Use intel_ prefix instead of i915_ as is more customary for
display related functions.
Include DRM_SCANOUTPOS_INVBL in the return value even w/o
adjustments, for a bit of extra consistency.
v3: Change the implementation to be based on DSL on all gens,
since that's enough for the needs of atomic updates, and
it will avoid complicating the scanout position calculations
for the vblank timestamps
v4: Don't break scanline wraparound for interlaced modes
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Seems I've been a bit dense with regards to the start of vblank
vs. the scanline counter / pixel counter.
After staring at the pixel counter on gen4 I came to the conclusion
that the start of vblank interrupt and scanline counter increment
happen at the same time. The scanline counter increment is documented
to occur at start of hsync, which means that the start of vblank
interrupt must also trigger there. Looking at the pixel counter value
when the scanline wraps from vtotal-1 to 0 confirms that, as the pixel
counter at that point reads hsync_start. This also clarifies why we see
need the +1 adjustment to the scaline counter. The counter actually
starts counting from vtotal-1 on the first active line.
I also confirmed that the frame start interrupt happens ~1 line after
the start of vblank, but the frame start occurs at hblank_start instead.
We only use the frame start interrupt on gen2 where the start of vblank
interrupt isn't available. The only important thing to note here is that
frame start occurs after vblank start, so we don't have to play any
additional tricks to fix up the scanline counter.
The other thing to note is the fact that the pixel counter on gen3-4
starts counting from the start of horizontal active on the first active
line. That means that when we get the start of vblank interrupt, the
pixel counter reads (htotal*(vblank_start-1)+hsync_start). Since we
consider vblank to start at (htotal*vblank_start) we need to add a
constant (htotal-hsync_start) offset to the pixel counter, or else we
risk misdetecting whether we're in vblank or not.
I talked a bit with Art Runyan about these topics, and he confirmed my
findings. And that the same rules should hold for platforms which don't
have the pixel counter. That's good since without the pixel counter it's
rather difficult to verify the timings to this accuracy.
So the conclusion is that we can throw away all the ISR tricks I added,
and just increment the scanline counter by one always.
Reviewed-by: Sourab Gupta <sourabgupta@gmail.com>
Reviewed-by: Akash Goel <akash.goels@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems we need this at least for the current platforms we have, but
probably not later. In any event, it should cause too much harm as we do
the same thing on several other platforms.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The same register exists for querying and programming eDRAM AKA eLLC. So
we can simply use it. For now, use all the same defaults as we had
for Haswell, since like Haswell, I have no further details.
I do not actually have a part with eDRAM, so I cannot test this.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I don't have any insight on what parts can do what. The docs do seem to
suggest WT caching works in at least the same manner as it does on
Haswell.
The addr = 0 is to shut up GCC:
drivers/gpu/drm/i915/i915_gem_gtt.c:80:7: warning: 'addr' may be used
uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On BDW we don't enable RC6 at the moment, but this isn't reflected in
the (sanitized) i915.enable_rc6 option. So make enable_rc6 report
correctly that RC6 is disabled, which will also effectively disable RPM
on BDW (since RPM depends on RC6).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77565
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
assert_plane_enabled() is now triggering during FDI link train because
we no longer enable planes that early.
This problem got introduced in:
commit a5c4d7bc18
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Mar 7 18:32:13 2014 +0200
drm/i915: Disable/enable planes as the first/last thing during modeset on ILK+
Just drop the assert since we shouldn't need planes for link training.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Squash in fixup for now unused plane local variable, reported
by 0-day tester.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 60f2b4af12.
The same warning has been fixed in e5081a538a and
these two commits got merged in 74e99a84de2d0980320612db8015ba606af42114 which
caused another warning. Simply, the reverted commit casted the pointer
difference to unsigned long and the other commit changed the output type from
long to ptrdiff_t.
The other commit fixes the original warning the better way so I'm reverting
this commit now.
Signed-off-by: Jan Moskyto Matejka <mq@suse.cz>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In recent dmesg logs reported for unrelated issues I noticed some power
domain WARNs caused by the following.
The workaround
commit ce35255032
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 20 10:14:23 2013 +0300
drm/i915: Fix unclaimed register access due to delayed VGA memory disable
and following fixup of it
commit a148532065
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Sep 16 17:38:34 2013 +0300
drm/i915: Move power well init earlier during driver load
was partially reverted by
commit 7f16e5c141
Merge: 9d1cb915e01dc7
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Nov 4 16:28:47 2013 +0100
Merge tag 'v3.12' into drm-intel-next
but kept the power domain put calls on the error path.
I think for now we can keep things as-is (not reintroduce the w/a) and just fix
the error path, since
- nobody complained seeing this issue
- according to Ville someone is reworking the VGA arbitration scheme at the
moment and when that's ready we have to rethink this part anyway
So fix this by just removing the put calls from the error path as well.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville noticed that we have this nice kerneldoc but it's not integrated
anywhere. Fix this asap!
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A common issue we have is that retiring requests causes recursion
through GTT manipulation or page table manipulation which we can only
handle at very specific points. However, to maintain internal
consistency (enforced through our sanity checks on write_domain at
various points in the GEM object lifecycle) we do need to retire the
object prior to marking it with a new write_domain, and also clear the
write_domain for the implicit flush following a batch.
Note that this then allows the unbound objects to still be on the active
lists, and so care must be taken when removing objects from unbound lists
(similar to the caveats we face processing the bound lists).
v2: Fix i915_gem_shrink_all() to handle updated object lifetime rules,
by refactoring it to call into __i915_gem_shrink().
v3: Missed an object-retire prior to changing cache domains in
i915_gem_object_set_cache_leve()
v4: Rebase
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've seen latencies up to 15msec, so increase the timeout to 20msec.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed by the VLV runtime PM helpers too, so factor it out.
Also add a safety check for the case where the previous force-off is
still pending, since I'm not sure if Punit can handle a new setting
while the previous one hasn't settled yet.
v2:
- unchanged
v3:
- add a note to the commit message about the safety check (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When enabling runtime PM on VLV, GT power save enabling becomes relatively
frequent, so optimize it a bit.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During runtime suspend there can be a last pending rps.work, so make
sure it's canceled. Note that in the runtime suspend callback we can't
get any RPS interrupts since it's called only after the GPU goes idle
and we set the minimum RPS frequency. The next possibility for an RPS
interrupt is only after getting an RPM ref (for example because of a new
GPU command) and calling the RPM resume callback.
v2:
- patch introduced in v2 of the patchset
v3:
- Change the order of canceling the rps.work and disabling interrupts to
avoid the race between interrupt disabling and the the rps.work. Race
spotted by Ville.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init sizzling on all platforms so move it to the
platform independent runtime resume callback. The ring frequency reinit
is also needed everywhere except on VLV, but gen6_update_ring_freq()
will be a noop on VLV, so we can move this function too to platform
independent code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by the next patch moving the call out from platform
specific RPM callbacks to platform independent code.
No functional change.
v2:
- patch introduce in v2 of the patchset
v3:
- simplify platform check condition (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to disable the interrupts for all platforms, so make the helpers
for this platform independent and call them from them platform
independent runtime suspend/resume callbacks.
On HSW/BDW this will move interrupt disabling/re-enabling at the
beginning/end of runtime suspend/resume respectively, but I don't see
any reason why this would cause a problem there. In any case this seems
to be the correct thing to do even on those platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV we depend on RC6 to save the GT render and media HW context
before going to the D3 state via RPM, so as a preparation for the
VLV RPM support (added in an upcoming patch) disable RPM if RC6 is
disabled.
There is probably a similar dependency on other platforms too, so for
safety require RC6 for those too. For these platforms (SNB, HSW, BDW)
this is then a possible fix.
v2:
- require RC6 for all RPM platforms, not just for VLV (Paulo, Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, an invalid enable_rc6 module option will be silently ignored, so
emit an info message about it. Doing an early sanitization we can also
reuse intel_enable_rc6() in a follow-up patch to see if RC6 is actually
enabled. Currently the caller would have to filter a non-zero return
value based on the platform we are running on. For example on VLV with
i915.enable_rc6 set to 2, RC6 won't be enabled but atm
intel_enable_rc6() would still return 2 in this case.
v2:
- simplify the platform check condition (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, we call intel_gt_powersave_enable() for GEN6 and GEN7 but disable
it for everything starting from GEN6. This is a problem in case of BDW.
Since I don't have a BDW to test if RC6 works properly, just keep it
disabled for now and fix only the disable function.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some platforms need additional power domains to be on in addition to the
device D0 state to access the panel registers.
Suggested by Daniel.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76987
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While checking the error capture path I noticed that we lacked the
power domain-on check for PIPESTAT so fix this by moving that to where
the rest of pipe registers are captured.
The move also revealed that we actually don't include this register in
the error report, so fix that too.
v2:
- patch introduced in v2 of the patchset
v3:
- add back !HAS_PCH_SPLIT check (Ville)
[ Ignore my previous comment about the gen<=5 || vlv check, I realized
that it's the same as !HAS_PCH_SPLIT. ]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
While checking the error capture path I noticed that this register is
read twice for GEN2, so fix this and also move the read where it's done
for other platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we can end up in the GPU reset deferred work in D3 state if the last
runtime PM reference is dropped between detecting a hang/scheduling the
work and executing the work. At least one such case I could trigger is
the simulated reset via the i915_wedged debugfs entry. Fix this by
getting an RPM reference around accessing the HW in the reset work.
v2:
- Instead of getting/putting the RPM reference in the reset work itself,
get it already before scheduling the work. By this we also prevent
going to D3 before the work gets to run, in addition to making sure
that we run the work itself in D0. (Ville, Daniel)
v3:
- fix inverted logic fail when putting the RPM ref on behalf of a
cancelled GPU reset work (Ville)
v4:
- Taking the RPM ref in the interrupt handler isn't really needed b/c
it's already guaranteed that we hold an RPM ref until the end of the
reset work in all cases we care about. So take the ref in the reset
work (for cases like i915_wedged_set). (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Be we read and chase pointers from the VBT, it is prudent to make sure
that those accesses are wholly contained within the MMIO region, or else
we may cause a kernel panic during boot.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure that the whole BDB section is within the MMIO region prior to
accessing it contents. That we don't read outside of the secion is left
up to the individual section parsers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on VLV but probably on other platforms too we depend on RC6
being enabled for RPM, so disable RPM until the delayed RC6 enabling
completes.
v2:
- explain the reason for the _noresume version of RPM get (Daniel)
- use the simpler 'if (schedule_work()) rpm_get();' instead of
'if (!cancel_work_sync()) rpm_get(); schedule_work();'
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Getting struct_mutex around the whole intel_enable_gt_powersave()
function is not necessary, since it's only needed for the ILK path
therein.
This will make intel_enable_gt_powersave() useable on the RPM resume
path for >=GEN6 (added in an upcoming patch to reset the RPS state
during RPM resume), where we can't (and need not) get this mutex.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These debugfs entries access registers that need the D0 power state so
get an RPM ref for them.
v2:
- for all these entries we only need D0 state, so get only an RPM ref,
not a power domain ref (Daniel, Paulo)
- the dpio entry is not an issue any more as it got removed (Ville)
- restore commit message from v1 (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are igt tools that can read/write the DPIO registers, so having a
debugfs entry for only some of those registers is somewhat arbitrary /
redundant. Remove it.
v2:
- instead of fixing the entry by taking a power domain reference around
the register accesses, remove the entry (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The parsing was incorrect for ILK and VLV.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not clearing this flag causes spurious interrupts at least in D3 state,
so before enabling RPM we need to fix this. We were already setting this
flag when enabling interrupts, only clearing it was missing.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These will be needed by the upcoming VLV RPM helpers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BDW GT3 has two independent BSD rings, which can be used to process the
video commands. To be simpler, it is transparent to user-space driver/middle.
Instead the kernel driver will decide which ring is to dispatch the BSD video
command.
As every BSD ring is powerful, it is enough to dispatch the BSD video command
based on the drm fd. In such case it can play back video stream while encoding
another video stream. The coarse ping-pong mechanism is used to determine
which BSD ring is used to dispatch the BSD video command.
V1->V2: Follow Daniel's comment and use the simple ping-pong mechanism.
This is only to add the support of dual BSD rings on BDW GT3 machine.
The further optimization will be considered in another patch set.
V2->V3: Follow Daniel's comment to use the struct_mutext instead of
atomic_t during determining which ring can be used to dispatch Video command.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Gen7 doesn't have the second BSD ring. But it will complain the switch check
warning message during compilation. So just add it to remove the
switch check warning.
V1->V2: Follow Daniel's comment to update the comment
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the hardware spec, the BDW GT3 machine has two independent
BSD ring that can be used to dispatch the video commands.
So just initialize it.
V3->V4: Follow Imre's comment to do some minor updates. For example:
more comments are added to describe the semaphore between ring.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[danvet: Fix up checkpatch error.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the hardware spec, the BDW GT3 has the different configuration
with the BDW GT1/GT2. So split the BDW device info definition.
This is to do the preparation for adding the Dual BSD rings on BDW GT3 machine.
V1->V2: Follow Daniel's comment to pay attention to the stolen check for BDW
in kernel/early-quirks.c
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to make sure that userspace keeps on following the contract,
otherwise we won't be able to use the reserved fields at all.
v2: Add DRM_DEBUG (Chris)
Testcase: igt/gem_exec_params/*-dirt
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bit tricky since 0 is also a valid constant ...
v2: Add DRM_DEBUG (Chris)
Testcase: igt/gem_exec_params/rel-constants-*
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we catch it, but silently succeed. Our userspace is
better than this.
v2: Add DRM_DEBUG (Chris)
Testcase: igt/gem_exec_params/sol-reset-*
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we include the expected values for the failing ring register checks,
it makes it marginally easier to see which is the culprit.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During module load, if we fail to initialise the rings, we abort the
load reporting EIO. However during resume, even though we report EIO as
we fail to reinitialize the ringbuffers, the resume continues and the
device is restored - albeit in a non-functional state. As we cannot
execute any commands on the GPU, it is effectively wedged, mark it so.
As we now preserve the ringbuffers across resume, this should prevent
UXA from falling into the trap of repeatedly sending invalid
batchbuffers and dropping all further rendering into /dev/null.
Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz>
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
[danvet: Drop unused error, spotted by Oscar.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even without enabling the ringbuffers to allow command execution, we can
still control the display engines to enable modesetting. So make the
ringbuffer initialization failure soft, and mark the GPU as wedged
instead.
v2: Only treat an EIO from ring initialisation as a soft failure, and
abort module load for any other failure, such as allocation failures.
v3: Add an *ERROR* prior to declaring the GPU wedged so that it stands
out like a sore thumb in the logs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tearing down the ring buffers across resume is overkill, risks
unnecessary failure and increases fragmentation.
After failure, since the device is still active we may end up trying to
write into the dangling iomapping and trigger an oops.
v2: stop_ringbuffers() was meant to call stop(ring) not
cleanup(ring) during resume!
Reported-by: Jae-hyeon Park <jhyeon@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=72351
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
[danvet: s/ring->obj == NULL/!intel_ring_initialized(ring)/ as
suggested by Oscar.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For readibility and guess at the meaning behind the constants.
v2: Claim only the meagerest connections with reality.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I don't think this is necessary; at least it doesn't appear to be on my
BYT. Dropping it speeds up our shutdown code a little, in some cases
resulting in faster init times.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When initially looking at traces, missed the fact the binary driver was
using large pages.
Fixes page faults when launching geometry shaders.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes a regression introduced by 060810d7ab "drm/nouveau: fix locking
issues in page flipping paths". chan->cli->mutex is unlocked a second time
in the fail_unreserve path, fix this by moving mutex_unlock down.
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There appear to be a crop of new hardware where the vbios is not
available from PROM/PRAMIN, but there is a valid _ROM method in ACPI.
The data read from PCIROM almost invariably contains invalid
instructions (still has the x86 opcodes), which makes this a low-risk
way to try to obtain a valid vbios image.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76475
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: <stable@vger.kernel.org> # v2.6.35+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Check to make sure the transaction succeeded before
using the register value. Fixes occasional link training
problems.
Noticed-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Testing the update pending bit directly after issuing an
update is nonsense cause depending on the pixel clock the
CRTC needs a bit of time to execute the flip even when we
are in the VBLANK period.
This is just a non invasive patch to solve the problem at
hand, a more complete and cleaner solution should follow
in the next merge window.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=76564
v2: fix source IDs for CRTC2-6
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Some RV7xx generation hardware crashes after you
raise the UVD clocks for the first time. Try to
avoid this by using the lower clocks to boot these.
Workaround for: https://bugzilla.kernel.org/show_bug.cgi?id=71891
v2: lower clocks on IB test as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Next pull request, this time more of the drm de-midlayering work. The big
thing is that his patch series here removes everything from drm_bus except
the set_busid callback. Thierry has a few more patches on top of this to
make that one optional to.
With that we can ditch all the non-pci drm_bus implementations, which
Thierry has already done for the fake tegra host1x drm_bus.
Reviewed by Thierry, Laurent and David and now also survived some testing
on my intel boxes to make sure the irq fumble is fixed correctly ;-) The
last minute rebase was just to add the r-b tags from Thierry for the 2
patches I've redone.
* 'drm-init-cleanup' of git://people.freedesktop.org/~danvet/drm:
drm/<drivers>: don't set driver->dev_priv_size to 0
drm: Remove dev->kdriver
drm: remove drm_bus->get_name
drm: rip out dev->devname
drm: inline drm_pci_set_unique
drm: remove bus->get_irq implementations
drm: pass the irq explicitly to drm_irq_install
drm/irq: Look up the pci irq directly in the drm_control ioctl
drm/irq: track the irq installed in drm_irq_install in dev->irq
drm: rename dev->count_lock to dev->buf_lock
drm: Rip out totally bogus vga_switcheroo->can_switch locking
drm: kill drm_bus->bus_type
drm: remove drm_dev_to_irq from drivers
drm/irq: remove cargo-culted locking from irq_install/uninstall
drm/irq: drm_control is a legacy ioctl, so pci devices only
drm/pci: fold in irq_by_busid support
drm/irq: simplify irq checks in drm_wait_vblank
Remove occurrences of unused struct qxl_device pointer in functions
qxl_ttm_fault() and qxl_init_mem_type().
Detected by Coverity: CID 1019128, CID 1019129.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For QXL hw we really want the bits to be replaced as we change
the preferred mode on the fly, and the same goes for virgl when
I get to it, however the original fix for this seems to have caused
a wierd regression on Intel G33 that in a stunning display of failure
at opposition to his normal self, Daniel failed to diagnose.
So we are left doing this, ugly ugly ugly ugly, Daniel you fixed
that G33 yet?, ugly, ugly.
Tested-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
Because the docs say ULX doesn't support it on HSW.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use %pad for dma_addr_t, because a dma_addr_t type can vary
based on build options. So, it prevents possible build warnings
in printks.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
devm_ioremap_resource() returns an error pointer, not NULL. Thus,
the result should be checked with IS_ERR().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
exynos_drm_crtc_mode_set assigns primary framebuffer to plane without
taking reference. Then during framebuffer removal it is dereferenced twice,
causing oops. The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
single security fix, cc'd stable.
* 'vmwgfx-fixes-3.15' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Make sure user-space can't DMA across buffer object boundaries v2
Otherwise we'll end up spamming dmesg on every context creation on snb
with vt-d enabled. This regression was introduced in
commit 246cbfb5fb
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Fri Dec 6 14:11:14 2013 -0800
drm/i915: Reorganize intel_enable_ppgtt
As the i915.enable_ppgtt is read-only it cannot be changed after the
module is loaded and so we can perform an early sanitization of the
values.
v2:
- Add comment and pimp commit message (Chris)
- Use the param consistently (Jani)
v3:
- Fix init sequence on pre-gen6 by moving the sanitize_ppgtt call to
gtt_init. Fixes boot hangs on pre-gen6.
- Add a debug output for the sanitize ppgtt mode.
References: https://lkml.org/lkml/2014/4/17/599
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77916
Cc: Alessandro Suardi <alessandro.suardi@gmail.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The function can never fail, and always returns 0, so it may just as
well not return anything.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The closing brace of the body of drm_addmap_core() is indented wrongly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace an occurrence of "adapater" with "adapter".
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix a few trivial typos in the framebuffer helper documentation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes up a couple of inconsistencies with kerneldoc comments for
the EDID related functions. Functions that return a value now use the
"Return" section consistently. For some exported symbols the kernel-doc
comments were not in the appropriate format and therefore not included
in the generated documentation. Others had no kernel-doc at all.
While at it, fix a couple of whitespace issues and capitalize common
abbreviations (i2c -> I2C, edid -> EDID, ...).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This argument is used to pass in the revision of the EDID, but since the
EDID is passed in as well, we can just as well get the revision from the
EDID structure directly.
While at it, update the kerneldoc comment.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 62ff94a549 "drm/crtc-helper: remove LOCKING from kerneldoc"
causes drm_helper_crtc_in_use() and drm_helper_encoder_in_use() to
complain loudly during a kernel panic or sysrq processing. This is
caused by nobody acquiring the modeset lock in these code paths.
This patch fixes this by trying to acquire the modeset lock for each
FB helper that's forced to kernel mode. If the lock can't be acquired,
it's likely that somebody else is performing a modeset. However, doing
another modeset concurrently might make things even worse, so the safe
option is to simply bail out in that case.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
inode argument is no longer in use (cf. f4aede2e3).
Remove it.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A single fix for some framebuffer reference counting fallout caused by
the primary plane helpers introduced in 3.15-rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=uM53
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.15-rc3' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Fixes for v3.15-rc3
A single fix for some framebuffer reference counting fallout caused by
the primary plane helpers introduced in 3.15-rc1.
* tag 'drm/tegra/for-3.15-rc3' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: restrict plane loops to legacy planes
Fixes for msm for 3.15.. a memory leak fix for devices using vram
carveout instead of iommu. Plus I think finally managed to sort out /
workaround some cursor vs underflow issues. And small fbcon tweak
needed to avoid extra full-modesets at boot.
* 'msm-fixes-3.15-rc3' of git://people.freedesktop.org/~robclark/linux:
drm/msm/mdp4: cure for the cursor blues (v2)
drm/msm: default to XR24 rather than AR24
drm/msm: fix memory leak
Fix regression with DVI and fix warns, and GM45 boot regression.
* tag 'drm-intel-fixes-2014-04-25' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Move all ring resets before setting the HWS page
drm/i915: Don't WARN nor handle unexpected hpd interrupts on gmch platforms
drm/i915: Allow full PPGTT with param override
drm/i915: Discard BIOS framebuffers too small to accommodate chosen mode
drm/i915: get power domain in case the BIOS enabled eDP VDD
drm/i915: Don't check gmch state on inherited configs
drm/i915: Allow user modes to exceed DVI 165MHz limit
Depending on the SDVO output_flags SDVO may have multiple connectors
linking to the same encoder (in intel_connector->encoder->base).
Only one of those connectors should be active (ie link to the encoder
thru drm_connector->encoder).
If intel_connector_break_all_links() is called from intel_sanitize_crtc()
we may break the crtc connection of an encoder thru an inactive connector
in which case intel_connector_break_all_links() will not be called again
for the active connector if this happens to come later in the list due to:
if (connector->encoder->base.crtc != &crtc->base)
continue;
in intel_sanitize_crtc().
This will however leave the drm_connector->encoder linkage for this
active connector in place. Subsequently this will cause multiple
warnings in intel_connector_check_state() to trigger and the driver
will eventually die in drm_encoder_crtc_ok() (because of crtc == NULL).
To avoid this remove intel_connector_break_all_links() and move its
code to its two calling functions: intel_sanitize_crtc() and
intel_sanitize_encoder().
This allows to implement the link breaking more flexibly matching
the surrounding code: ie. in intel_sanitize_crtc() we can break the
crtc link separatly after the links to the encoders have been
broken which avoids above problem.
This regression has been introduced in:
commit 2492935248
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jul 2 20:28:59 2012 +0200
drm/i915: read out the modeset hw state at load and resume time
so goes back to the very beginning of the modeset rework.
v2: This patch takes care of the concernes voiced by Chris Wilson
and Daniel Vetter that only breaking links if the drm_connector
is linked to an encoder may miss some links.
v3: move all encoder handling to encoder loop as suggested by
Daniel Vetter.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In commit a51435a313
Author: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Date: Wed Mar 12 16:39:40 2014 +0530
drm/i915: disable rings before HW status page setup
we reordered stopping the rings to do so before we set the HWS register.
However, there is an extra workaround for g45 to reset the rings twice,
and for consistency we should apply that workaround before setting the
HWS to be sure that the rings are truly stopped.
Reference: http://lkml.kernel.org/r/20140423202248.GA3621@amd.pavel.ucw.cz
Tested-by: Pavel Machek <pavel@ucw.cz>
Cc: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The status bits are unconditionally set, the control bits only enable
the actual interrupt generation. Which means if we get some random
other interrupts we'll bogusly complain about them.
So restrict the WARN to platforms with a sane hotplug interrupt
handling scheme. And even more important also don't attempt to process
the hpd bit since we've detected a storm already. Instead just clear
the bit silently.
This WARN has been introduced in
commit b8f102e8bf
Author: Egbert Eich <eich@suse.de>
Date: Fri Jul 26 14:14:24 2013 +0200
drm/i915: Add messages useful for HPD storm detection debugging (v2)
before that we silently handled the hpd event and so partially
defeated the storm detection.
v2: Pimp commit message (Jani)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Egbert Eich <eich@suse.de>
Cc: bitlord <bitlord0xff@gmail.com>
Reported-by: bitlord <bitlord0xff@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The hw cursor is relatively adept at triggering underflows, which
manifest as a "blue flash" (since blue is configured as the underflow
color). Juggle a few things around to tighten up the timing for setting
cursor registers in DONE irq.
And most importantly, don't ever disable the hw cursor. Instead flip it
to a blank/empty cursor. This seems far more reliable, as even simply
clearing the cursor-enable bit (with no other updates in previous/
following frames) can in some cases cause underflow.
v1: original
v2: add missing locking spotted by Micah
Cc: Micah Richert <richert@braincorporation.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since X11 is going to create an XR24 fb, if the pixel formats do not
match then crtc helpers will think it is a full modeset even if mode is
the same, which prevents smooth/flickerless handover from fbcon/plymouth
to X11.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In Matt Ropers primary plane series a set of prep patches like
commit af2b653bfb
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Apr 1 15:22:32 2014 -0700
drm/i915: Restrict plane loops to only operate on overlay planes (v2)
ensured that all exisiting users of the mode_config->plane_list
wouldn't change behaviour. Unfortunately tegra seems to have fallen
through the cracks. Fix it.
This regression was introduced in
commit e13161af80
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Apr 1 15:22:38 2014 -0700
drm: Add drm_crtc_init_with_planes() (v2)
The result was that we've unref'ed the fb for the primary plane twice,
leading to a use-after free bug. This is because the drm core will
already set crtc->primary->fb to NULL and do the unref for us, and the
crtc disable hook is called by the drm crtc helpers for exactly this
case.
Aside: Now that the fbdev helpers clean up planes there's no longer a
need to do this in drivers. So this could probably be nuked entirely
in linux-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When PPGTT was disabled by default, the patch also prevented the user
from overriding this behavior via module parameter. Being able to test
this on arbitrary kernels is extremely beneficial to track down the
remaining bugs. The patch that prevented this was:
commit 93a25a9e2d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 6 09:40:43 2014 +0100
drm/i915: Disable full ppgtt by default
By default PPGTT is set to -1. 0 means off, 1 means aliasing only, 2
means full, all other values are reserved.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If the inherited BIOS framebuffer is smaller than the mode selected for
fbdev, then if we continue to use it then we cause display corruption as
we do not setup the panel fitter to upscale.
Regression from commit d978ef1445
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Mar 7 08:57:51 2014 -0800
drm/i915: Wrap the preallocated BIOS framebuffer and preserve for KMS fbcon v12
v2: Add a debug message to track the discard of the BIOS fb.
v3: Ville pointed out the difference between ref/unref
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77767
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We already check that the buffer object we're accessing is registered with
the file. Now also make sure that we can't DMA across buffer object boundaries.
v2: Code commenting update.
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
The ->disable_plane hook always had a return value, but only since the
introduction of primary planes was there any implementation that
actually failed.
So handle such failures correctly.
Note that drm_plane_force_disable is special: In the modeset cleanup
case we first disable all crtc, so primary planes should all be freed
already. And in the fb helper we only reset non-primary planes. Still
better be paranoid and add an early return.
I don't see how this could happen, but it might fix the fb refcount
underrun Thierry is seeing. Matt Roper spotted this issue.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The introduction of primary planes has apparently caused a bit of fb
refcounting fun for people. That makes it a good time to clean up the
arcane rules and slight differences between ->update_plane and
->set_config. The new rules are:
- The core holds a reference for both the new and the old fb (if
they're non-NULL of course) while calling into the driver through
either ->update_plane or ->set_config.
- Drivers may not clobber plane->fb if their callback fails. If they
do that, they need to store a pointer to the old fb in it again.
When calling into the driver plane->fb still points at the current
(old) framebuffer.
- The core will update the plane->fb pointer on success. Drivers can
do that themselves too, but aren't required to any more for the
primary plane.
- The core will update fb refcounts for the plane->fb pointer,
presuming the drivers hold up their end of the bargain.
v2: Remove now unused tmpfb (Thierry)
v3: Drop broken changes from drm_mode_setplane (Ville). Also polish
the commit message a bit.
v4: Also fix up the handling of ->disable_plane in
drm_plane_force_disable. The issue was that we didn't save plane->fb
over the ->disable_plane call. Just paranoia, nothing relies on this.
v5: Keep still useful comments about directly calling ->set_config,
which I should have done for v4 already. Requested by Matt.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Especially not on modesetting drivers - this is used to size
the driver private structure for legacy drm buffers.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the last patch to ditch the ->get_name callbacks the last
user is now gone.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The only user is the info debugfs file, so we only need something
human readable. Now for both pci and platform devices we've used the
name of the underlying device driver, which matches the name of the
drm driver in all cases. So we can just use that instead.
The exception is usb, which used a generic "USB". Not to harmful with
just one usb driver, but better to use "udl", too.
With that converted we can rip out all the ->get_name implementations.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was only ever used to pretty-print the irq driver name. And on
kms systems due to set_version bonghits we never set up the prettier
name, ever. Which make this a bit pointless.
Also, we can always dig out the driver-instance/irq relationship
through other means, so this isn't that useful. So just rip it out to
simplify the set_version/set_busid insanity a bit.
Also delete the temporary busname from drm_pci_set_busid, it's now
unused.
v2: Rebase on top of the new host1x drm_bus for tegra.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is only used for drm versions 1.0, and kms drivers have never
been there. So we can appropriately restrict this to legacy and hence
pci devices and inline everything.
v2: Make the dummy function actually return something, caught by Wu
Fengguang's 0-day tester.
v3: Fix spelling in comment (Thierry)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that they're all unused we can get rid of them, including the
dummy version in drm_usb.c.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unfortunately this requires a drm-wide change, and I didn't see a sane
way around that. Luckily it's fairly simple, we just need to inline
the respective get_irq implementation from either drm_pci.c or
drm_platform.c.
With that we can now also remove drm_dev_to_irq from drm_irq.c.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's only ever called for legacy drivers, which are all pci.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To get rid of the dev->bus->get_irq callback we need to pass in the
desired irq explicitly into drm_irq_install. To avoid having to do the
same for drm_irq_unistall just track it internally. That leaves
drivers with less room to botch things up.
v2: Add the hunk lost in an earlier patch to this one (Thierry).
v3: Fix up the totally fumbled logic in drm_irq_install and use the
local variable consistently. Spotted by both Thierry and Laurent.
Shame on me for failing to properly test the rebase version of this
patch ...
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since really that's all it protects - legacy horror stories in
drm_bufs.c. Since I don't want to waste any more time on this I didn't
bother to actually look at what it protects in there, but it's at
least contained now.
v2: Move the spurious hunk to the right patch (Thierry).
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So I just wanted to add a new field to struct drm_device and
accidentally stumbled over something. According to comments
dev->open_count is protected by dev->count_lock, but that's totally
not the case. It's protected by drm_global_mutex.
Unfortunately the vga switcheroo callbacks took this comment at face
value. The problem is that we can't just take the drm_global_mutex
because:
- It would lead to a locking inversion with the driver load/unload
paths.
- It wouldn't actually protect anything, for that we'd need to wrap
the entire vga switcheroo code in the drm_global_mutex. And I'm not
sure whether that would actually solve anything.
What we probably want is a try_to_grab_switcheroo reference kind of
thing which is used in the driver's ->open callback. Then we could
move all that ->can_switch madness into the vga switcheroo core where
it really belongs.
But since that would amount to real work take the easy way out and
just add a comment. It's definitely not going to make anything worse
since doing switcheroo state changes while restarting X just isn't
recommended. Even though the delayed switching code does exactly that.
v2:
- Simplify the ->can_switch implementations more (Thierry)
- Fix comment about the dev->open_count locking (Thierry)
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> (v1)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If I unplug the eDP monitor, the BIOS of my machine will enable the
VDD bit, then when the driver loads it will think VDD is enabled. It
will detect that the eDP is not enabled and return false from
intel_edp_init_connector. This will trigger a call to
edp_panel_vdd_off_sync(), which trigger a WARN saying that the
refcount of the power domain is less than zero.
The problem happens because the driver gets a refcount whenever it
enables the VDD bit, and puts the refcount whenever it disables the
VDD bit. But on this case, the BIOS enabled VDD, so all we do is to
call put() without calling get() first, so the code added is there to
make sure we always have the get() in case the BIOS enabled the bit.
This regression was introduced in
commit e9cb81a228
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Nov 21 13:47:23 2013 -0200
drm/i915: get a runtime PM reference when the panel VDD is on
v2: - Rebase
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
... our current modeset code isn't good enough yet to handle this. The
scenario is:
1. BIOS sets up a cloned config with lvds+external screen on the same
pipe, e.g. pipe B.
2. We read out that state for pipe B and assign the gmch_pfit state to
it.
3. The initial modeset switches the lvds to pipe A but due to lack of
atomic modeset we don't recompute the config of pipe B.
-> both pipes now claim (in the sw pipe config structure) to use the
gmch_pfit, which just won't work.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74081
Tested-by: max <manikulin@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Some newer PX laptops have the pci device class
set to DISPLAY_OTHER rather than DISPLAY_VGA. This
properly detects ATPX on those laptops.
Based on a patch from: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Cc: airlied@gmail.com
Avoids a crash in certain cases when thermal irqs are generated
before the display structures have been initialized.
v2: fix the vblank and vrefresh helpers as well
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=73931
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We need to check whether drm_ht_create succeed and clean up
if not.
Spotted by coverity.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is C standard hair-splitting, but afaict
- sum will be promoted to signed int in computation since
uint8_t fits
- signed overflow is undefined.
No we need to add up an awful lot of bytes to actually make it
overflow. But I guess the real risk is gcc spotting this and going
bananas. Fix this by simply using unsigned in to force all computations
to use the well-defined unsigned behaviour.
Spotted by coverity.
v2: Simplify the entire computation as suggested by Jean.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ->gem_free_object never gets called with a NULL pointer, the check
is redundant. Also checking after the upcast allows compilers to elide
it anyway.
Noticed while chasing coverity reports, somehow this one here was not
flagged.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ttm_bo_unref unconditionally calls kref_put on it's argument, so the
thing can't be NULL without already causing Oopses.
Spotted by coverity.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to set it to -ENODEV when we don't recognize the device.
Otherwise we return/print stack garbage.
Spotted by coverity.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The context_dtor callback is only called once we've successfully loaded
the driver, which means dev->dev_private is set up. The check is hence
pointless.
Also dev->dev_private is deref already above, so compilers are free
to elide it anyway.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ->gem_free_object never gets called with a NULL pointer, the check
is redundant. Also checking after the upcast allows compilers to elide
it anyway.
Spotted by coverity.
v2: Fix patch subject.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ttm_bo_unref unconditionally calls kref_put on it's argument, so the
thing can't be NULL without already causing Oopses.
Spotted by coverity.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ->gem_free_object never gets called with a NULL pointer, the check
is redundant. Also checking after the upcast allows compilers to elide
it anyway.
Spotted by coverity.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ttm_bo_unref unconditionally calls kref_put on it's argument, so the
thing can't be NULL without already causing Oopses.
Spotted by coverity.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ->gem_free_object never gets called with a NULL pointer, the check
is redundant. Also checking after the upcast allows compilers to elide
it anyway.
Spotted by coverity.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ttm_bo_unref unconditionally calls kref_put on it's argument, so the
thing can't be NULL without already causing Oopses.
Spotted by coverity.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Should be 5 rather than 4.
Noticed-by: Mathias Fröhlich <Mathias.Froehlich@gmx.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christian König <christian.koenig@amd.com>
In commit
commit 6375b768a9
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Mar 3 11:33:36 2014 +0200
drm/i915: Reject >165MHz modes w/ DVI monitors
the driver started to filter out display modes which exceed the
single-link DVI 165Mz dotclock limits when the monitor doesn't report
itself as being HDMI compliant. The intent was to filter out all
EDID derived modes that require dual-link DVI to operate since we
don't support dual-link.
However the patch went a bit too far and also causes the driver to reject
such modes even when specified by the user. Normally we don't check the
sink limitations when setting a mode from the user. This allows the user
to specify any mode whether the sink reports to support it or not. This
can be useful since often the sinks support more modes than they report
in the EDID.
So relax the checks a bit, and apply the single-link DVI dotclock limit
only when filtering the mode list, and ignore the limit when setting
a user specified mode.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=72961
Tested-by: Nicholas Vinson <nvinson@comcast.net>
Cc: stable@vger.kernel.org [3.14]
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Completely unused. Hooray, midlayer mistakes that didn't cause work to
undo!
v2: Rebase on top of the recent tegra changes which added a host1x drm
bus.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only used in some legacy pci drivers, and dereferencing the PCI irq is
actually shorter ...
Since this removes all users for drm_dev_to_irq from the tree except
in drm_irq.c, move the inline helper in there. It'll disappear soon,
too.
v2: Polish commit message (Thierry)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The dev->struct_mutex locking in drm_irq.c only protects
dev->irq_enabled. Which isn't really much at all and only prevents
especially nasty ums userspace from concurrently installing the
interrupt handling a few times. Or at least trying.
There are tons of unlocked readers of dev->irqs_enabled in the vblank
wait code (and by extension also in the pageflip code since that uses
the same vblank timestamp engine).
Real modesetting drivers should ensure that nothing can go haywire
with a sane setup teardown sequence. So we only really need this for
the drm_control ioctl, everywhere else this will just paper over
nastiness.
Note that drm/i915 is a bit specially due to the gem+ums combination.
So there we also need to properly protect the entervt and leavevt
ioctls. But it's definitely saner to do everything in one go than to
drop the lock in-between.
Finally there's the gpu reset code in drm/i915. That one's just race
(concurrent userspace calls to for vblank waits of pageflips could
spuriously fail). So wrap it up in with a nice comment since fixing
this is more involved.
v2: Rebase and fix commit message (Thierry)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a ums-only ioctl, and we've only ever supported ums (at least
in upstream) on pci devices. So no point in keeping that piece of
legacy logic abstracted within the drm bus driver.
To keep things work without CONFIG_PCI also add a dummy ioctl.
v2: Block the irq_by_busid ioctl for modeset drivers.
v3: Spelling/whitespace polish (Thierry)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Checking for both an irq number _and_ whether it's enabled is
redundant. Originally I've thought the drm_dev_to_irq call would break
drivers which do their own irq checking, but those shouldn't have
DRIVER_HAVE_IRQ set as Thierry Reding pointed out. But such drivers
already need to set dev->irq_enabled for other reasons, so we might as
well ditch that check, too.
v2: Also drop the HAVE_IRQ check.
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've forgotten to clean this all up correctly in
commit e3d6ddb35f
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Apr 1 22:15:00 2014 +0200
drm/crtc-helper: don't disable disconnected outputs
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By the time drm_mode_config_cleanup calls this all the hw state should
be cleaned up already - we even have a WARN right before calling
plane->destroy callbacks asserting that all framebuffers are gone.
So trying to disable things harder is a bit a bug. Caught by Thierry
since it resulted in some mode_config.mutex locking backtraces.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The src_w / src_h parameters to update_plane include a subpixel offset;
we need to shift off the subpixel bits before comparing to CRTC size
when checking for primary plane scaling.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many drm connectors do not need mode validation.
The patch makes this callback optional and removes dumb implementations.
v2: Rebase:
- imx move to a shared (but still dummy) ->mode_valid implementation.
- probe helpers have been extracted to drm_probe_helper.c
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The hpd (hot plug detect) pin assignment got lost
in the conversion to to the common i2c over aux
code. Without this information, aux transactions
do not work properly. Fixes DP failures.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Populate PAR in infoframe structure. If there is a user setting for PAR, then
that value is set. Else, value is taken from CEA mode list if VIC is found.
Else, PAR is calculated from resolution. If none of these conditions are
satisfied, PAR is NONE as per initialization.
v2: Removed the part which sets PAR according to user input, based on
Daniel's review comments.
A separate patch will be submitted to create a property that would enable a
user space app to set aspect ratio for AVI infoframe.
v2: Removed the part which sets PAR according to user input, based on
Daniel's review comments.
v3: Removed calculation of PAR for non-CEA modes as per discussion with
Ville.
A separate patch will be submitted to create a property that would enable a
user space app to set aspect ratio for AVI infoframe.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jesse Barnes <jesse.barnes@intel.com>
Cc: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Squash in fixup for htmldocs.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some i2c fixes over DisplayPort.
* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: Improve vramlimit module param documentation
drm/radeon: fix audio pin counts for DCE6+ (v2)
drm/radeon/dp: switch to the common i2c over aux code
drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
drm/i915: support address only i2c-over-aux transactions
drm/tegra: dp: Support address-only I2C-over-AUX transactions
bochs kms driver lacks power management support, thus
the vga display doesn't work any more after S3 resume.
Fix this by adding suspend and resume functions.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
cirrus kms driver lacks power management support, thus
the vga display doesn't work any more after S3 resume.
Fix this by adding suspend and resume functions.
Also make the mode_set function unblank the screen.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is leftover stuff from my previous doc round which I kinda wanted
to do but didn't yet due to rebase hell.
The modeset helpers and the probing helpers a independent and e.g.
i915 uses the probing stuff but has its own modeset infrastructure. It
hence makes to split this up. While at it add a DOC: comment for the
probing libraray.
It would be rather neat to pull some of the DocBook documenting these
two helpers into in-line DOC: comments. But unfortunately kerneldoc
doesn't support markdown or something similar to make nice-looking
documentation, so the current state is better.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After thinking about this topic a bit more I've reached the conclusion
that implementing this doesn't make sense:
- The locking is all wrong: set_config(NULL) will also unlink encoders
and connectors, but those links are protected with the mode_config
mutex. In the ->disable_plane callback we only hold all modeset
locks, but eventually we want to switch to just grabbing the
per-crtc (and maybe per-plane) locks as needed, maybe based on
ww_mutexes. Having a callback which absolutely needs all modeset
locks is bad for this conversion.
Note that the same isn't true for the provided ->update_plane since
we've audited the crtc helpers to make sure that not encoder or
connector links are changed.
- There's no way to re-enable the plane with an ->update_plane: The
connectors/encoder links are lost and so we can't re-enable the
CRTC. Even without that issue the driver might have reassigned some
shared resources (as opposed to e.g. DPMS off, where drivers are not
allowed to do that to make sure the CRTC can be enabled again).
- The semantics don't make much sense: Userspace asked to scan out
black (or some other color if the driver supports a background
color), not that the screen be disabled.
- Implementing proper primary plane support (i.e. actually disabling
the primary plane without disabling the CRTC) is really simple, at
least if all the hw needs is flipping a bit. The big task is
auditing all the interactions with other ioctls when the CRTC is on
but there's no primary plane (e.g. pageflips). And some of that work
still needs to be done.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this is a typo vs the ums driver, fix to check correct value.
Found initially by Coverity.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 457e77b264 added two checks applied to a
value received from nv_rd32(bios, 0x619f04). But after this new piece of code
is executed, the addr local variable does not hold the same value it used to
hold before the commit. Here is what is was assigned in the original code:
(u64)(nv_rd32(bios, 0x619f04) & 0xffffff00) << 8
in the committed code it ends up with this value:
(u64)(nv_rd32(bios, 0x619f04) >> 8) << 8
These expressions are obviously not equivalent.
My Nvidia video card does not show anything on the display when I boot a
kernel containing this commit.
The patch fixes the code so that the new checks are still done, but the
side effect of an incorrect addr value is gone.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
appeared in 3.15-rc1:
- fixes for primary-plane handling which caused crashes
- fix all kinds of uninit issues which prevented from unloading the omapdrm
module.
- fixes for HDMI enable/disable issues
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=03GJ
-----END PGP SIGNATURE-----
Merge tag 'omapdrm-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
Fixes for omapdrm, some of which were already present in 3.14, and some which
appeared in 3.15-rc1:
- fixes for primary-plane handling which caused crashes
- fix all kinds of uninit issues which prevented from unloading the omapdrm
module.
- fixes for HDMI enable/disable issues
* tag 'omapdrm-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
drm/omap: fix the handling of fb ref counts
drm/omap: protect omap_crtc's event with event_lock spinlock
drm/omap: Use old_fb to synchronize between successive page flips
drm/omap: Fix crash when using LCD3 overlay manager
drm/omap: gem sync: wait on correct events
drm/omap: Fix memory leak in omap_gem_op_async
drm/omap: remove warn from debugfs
drm/omap: remove extra plane->destroy from crtc destroy
drm/omap: print warning when rotating non-TILER fb
drm/omap: fix missing unref to fb's buf object
drm/omap: fix plane rotation
drm/omap: fix enabling/disabling of video pipeline
drm/omap: fix missing disable for unused encoder
drm/omap: fix race issue when unloading omapdrm
drm/omap: fix DMM driver (un)registration
drm/omap: fix uninit order in pdev_remove()
drm/omap: fix output enable/disable sequence
1. Fixing PLL regressions
2. A couple of memory reclocking and DPM fixes
3. Small cleanups
* 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon/ci: make sure mc ucode is loaded before checking the size
drm/radeon/si: make sure mc ucode is loaded before checking the size
drm/radeon: improve PLL params if we don't match exactly v2
drm/radeon: memory leak on bo reservation failure. v2
drm/radeon: fix VCE fence command
drm/radeon: re-enable mclk dpm on R7 260X asics
drm/radeon: add support for newer mc ucode on CI (v2)
drm/radeon: add support for newer mc ucode on SI (v2)
drm/radeon: apply more strict limits for PLL params v2
drm/radeon: update CI DPM powertune settings
drm/radeon: fix runpm handling on APUs (v4)
drm/radeon: disable mclk dpm on R7 260X
This contains a fix for the host1x driver writing to non-existent syncpt
registers.
A second commit removes an excess pad field in the parameter structure
for the DRM_TEGRA_SUBMIT IOCTL. Archeaology on earlier versions of this
file indicates that this was once there to pad an uneven number of u32
u32 fields, of which one was subsequently removed. Unfortunately nobody
remembered to get rid of the padding when that happened.
Both of these commits are Cc: stable because they fix issues that were
introduced back in v3.10.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=yHpw
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.15-rc2' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Fixes for v3.15-rc2
This contains a fix for the host1x driver writing to non-existent syncpt
registers.
A second commit removes an excess pad field in the parameter structure
for the DRM_TEGRA_SUBMIT IOCTL. Archeaology on earlier versions of this
file indicates that this was once there to pad an uneven number of u32
u32 fields, of which one was subsequently removed. Unfortunately nobody
remembered to get rid of the padding when that happened.
Both of these commits are Cc: stable because they fix issues that were
introduced back in v3.10.
* tag 'drm/tegra/for-3.15-rc2' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: Remove gratuitous pad field
gpu: host1x: handle the correct # of syncpt regs
Avoid a possible segfault.
Noticed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Avoid a possible segfault.
Noticed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
On bo reservation failure, we end up leaking fpriv.
v2 (chk): rebased and added missing free on vm failure as well
Fixes: 5e386b574c ("drm/radeon: fix missing bo reservation")
Cc: stable@vger.kernel.org
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Due to a type mismatch that causes an implicit type conversion, the
upper 32 bits of the GPU address have been zeroed out when adding to the
command buffer.
Picked up by Coverity - CID 1198624.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
May fix stability issues with some newer cards.
v2: print out mc firmware version used and size
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Letting post and refernce divider get to big is bad for signal stability.
v2: increase the limit to 210
Signed-off-by: Christian König <christian.koenig@amd.com>
The pipe is off at that point in time, so a vblank wait is simply a
50ms wait. Caught by Jesse's verbose "make vblank wait timeouts WARN"
patch. We've probably had a few versions of this float around already.
To document assumptions put a pipe assert into the same place. And
also add a posting read.
If we ever decide to update the eld and infoframes while the pipe is
already on (e.g. for fastboot) then there's lots of work to do. So
better properly document all the hidden assumptions.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BIT_WORD() truncates rather than rounds, so the loops in
syncpt_thresh_isr() and _host1x_intr_disable_all_syncpt_intrs() use <=
rather than < in an attempt to process the correct number of registers
when rounding of the conversion of count of bits to count of words is
necessary. However, when rounding isn't necessary because the value is
already a multiple of the divisor (as is the case for all values of
nb_pts the code actually sees), this causes one too many registers to
be processed.
Solve this by using and explicit DIV_ROUND_UP() call, rather than
BIT_WORD(), and comparing with < rather than <=.
Fixes: 7ede0b0bf3 ("gpu: host1x: Add syncpoint wait and interrupts")
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some fixes from Intel.
* tag 'drm-intel-fixes-2014-04-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Always use kref tracking for all contexts.
drm/i915: do not setup backlight if not available according to VBT
drm/i915: check VBT for supported backlight type
drm/i915: Disable self-refresh for untiled fbs on i915gm
drm/mm: Don't WARN if drm_mm_reserve_node
We already do this for HSW, but doing it makes sense for everything else
as well. Extend it for ILK/SNB/IVB since that's where the new watermark
code is used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
[danvet: Resolve conflict since I've plucked this out of the middle of
Ville's series.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like on hsw/bdw the pipe isn't actually running yet at this point.
This holds for both pch ports and the cpu edp port according to my
testing on ilk, snb and ivb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This cleans up the checkpatch errors for the merged commit -
commit d3b542fcfc
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Mon Apr 14 11:00:34 2014 +0530
drm/i915: Add parsing support for new MIPI blocks in VBT
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When linking the i2c sysfs file into the connector's directory
pass directory and link target in the right order.
This code was introduced with:
commit 931c1c2698
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Feb 11 17:12:51 2014 +0200
drm/i915: sdvo: add i2c sysfs symlink to the connector's directory
This is the same what we do for DP connectors, so make things more
consistent.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the recent primary-plane changes for drm, the primary plane's
framebuffer needs to be ref counted the same way as for
non-primary-planes. This was not done by the omapdrm driver, which
caused the ref count to drop to 0 too early, causing problems.
This patch moves the fb unref and ref from omap_plane_update to
omap_plane_mode_set. This way the fb refs are updated for both primary
and non-primary cases, as omap_plane_update calls omap_plane_mode_set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vblank_cb callback and the page_flip ioctl can occur together in different
CPU contexts. vblank_cb uses takes tje drm device's event_lock spinlock when
sending the vblank event and updating omap_crtc->event and omap_crtc->od_fb.
Use the same spinlock in page_flip, to make sure the above omap_crtc parameters
are configured sequentially.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_crtc->old_fb is used to check whether the previous page flip has completed
or not. However, it's never initialized to anything, so it's always NULL. This
results in the check to always succeed, and the page_flip to proceed.
Initialize old_fb to the fb that we intend to flip to through page_flip, and
therefore prevent a future page flip to proceed if the last one didn't
complete.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The channel_names list didn't have a string populated for LCD3 manager, this
results in a crash when the display's output is connected to LCD3. Add an entry
for LCD3.
Reported-by: Somnath Mukherjee <somnath@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A waiter of the type OMAP_GEM_READ should wait for a buffer to be completely
written, and only then proceed with reading it. A similar logic applies for
waiters with OMAP_GEM_WRITE flag.
Currently the function is_waiting() waits on the read_complete/read_target
counts in the sync object.
This should be the other way round, as a reader should wait for users who are
'writing' to this buffer, and vice versa.
Make readers of the buffer(OMAP_GEM_READ) wait on the write counters, and
writers to the buffer(OMAP_GEM_WRITE) wait on the read counters in is_waiting()
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In omap_gem_op_async(), if a waiter is not added to the wait list, it needs to
be free'd in the function itself.
Make sure we free the waiter for this case.
Signed-off-by: Subhajit Paul <subhajit_paul@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Patch dfe96ddcfa (omapdrm: simplify locking in
the fb debugfs file) removed taking locks when using omapdrm's debugfs
to dump fb objects.
However, in omap_gem_describe we give a WARN is the lock has not been
taken, so that WARN is now seen every time omapdrm debugfs is used.
So, presuming the removal of locks is ok, we can also remove the WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the planes, including primary planes, are now destroyed by the drm
framework. Thus we no longer need the explicit call to plane->destroy
from the crtc's destroy function.
This patch removes the call, thus fixing the crash caused by double
freeing the plane.
remove omap_crtc->plane->funcs->destroy(omap_crtc->plane)
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Print a warning when the user tries to rotate a non-TILER framebuffer.
Also set the rotation to 0, to avoid constant flood of the warnings in
case of page flipping.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_fbdev_create() takes a reference to the fb's gem object with
omap_gem_get_paddr(). However, it never releases it with
omap_gem_put_paddr().
This patch adds the missing omap_gem_put_paddr() to omap_fbdev_free().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Plane rotation with omapdrm is currently broken.
It seems omap_plane_mode_set() expects width and height in screen
coordinates, so pass it like that.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment the omap_crtc_pre_apply() handles the enabling, disabling
and configuring of encoders and panels separately from the CRTC (i.e.
the overlay manager).
However, this doesn't work correctly. The encoder driver has to be in
control of its video input (i.e. the crtc) for correct operation.
This problem causes bugs with (at least) HDMI: the HDMI encoder supplies
pixel clock for DISPC, and DISPC supplies video stream for HDMI. The
current code first enables the HDMI encoder, and CRTC after that.
However, the encoder expects the video stream to start during the
encoder's enable, and if it doesn't, there will be sync lost errors.
The encoder enables its video source by calling src->enable(), and this
call goes to omapdrm (omap_crtc_enable), but omapdrm doesn't do anything
in that function. Similarly for disable, which goes to
omap_crtc_disable().
This patch moves the code to setup and enable/disable the crtc to
omap_crtc_enable. and omap_crtc_disable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
When an encoder is no longer connected to a crtc, the driver will leave
the encoder enabled.
This patch adds code to track the encoder used for a crtc, and when the
encoder changes, the old one is disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At module unload, omap_fbdev_free() gets called which releases the
framebuffers. However, the framebuffers are still used by crtcs, and
will be released only later at vsync. The driver doesn't wait for this,
and goes on to release the rest of the resources, which often
causes a crash.
This patchs adds a omap_crtc_flush() function which waits until the crtc
has finished with its apply queue and page flips.
The function utilizes a simple polling while-loop, as the performance is
not an issue here.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At the moment the DMM driver is never unregistered, even if it's
registered in the omapdrm module's init function. This means we'll get
errors when reloading the omapdrm module.
Fix this by unregistering the DMM driver properly, and also change the
module init to fail if DMM driver cannot be registered, simplifying the
unregister path as we don't need to keep the state whether we registered
the DMM driver or not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
When unloading omapdrm driver, the omapdrm platform device is
uninitialized last, after the displays have been disconnected omap_crtc
callbacks have been removed. As the omapdrm pdev uninitialization needs
the features uninitialized in earlier steps, a crash is guaranteed.
This patch fixes the uninitialize order so that the omapdrm pdev is
removed first.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
At the moment it's quite easy to get the following errors when the HDMI
output is enabled or disabled:
[drm:omap_crtc_error_irq] *ERROR* tv: errors: 00008000
The reason for the errors is that the omapdrm driver doesn't properly
handle the sync-lost irqs that happen when enabling the DIGIT crtc,
which is used for HDMI and analog TV. The driver does disable the
sync-lost irq properly, but it fails to wait until the output has been
fully enabled (i.e. the first vsync), so the sync-lost errors are still
seen occasionally.
This patch makes the omapdrm act the same way as the omapfb does:
- When enabling a display, we'll wait for the first vsync.
- When disabling a display, we'll wait for framedone if available, or
odd and even vsyncs.
These changes make sure the output is fully enabled or disabled at the
end of the function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Sanjay Singh Rawat <sanjay.rawat@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
The parser extracts the config block(#52) and sequence(#53) data
and store in private data structures.
v2: Address review comments by Jani
- adjust code for the structure changes for bdb_mipi_config
- add boundry and buffer overflow checks as suggested
- use kmemdup instead of kmalloc and memcpy
v3: More strict check while parsing VBT
- Ensure that at anytime we do not go beyond sequence block
while parsing
- On unknown element fail the whole parsing
v4: Style changes and spell check mostly as suggested by Jani
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we really only need this when the pfit is enabled, at least
I couldn't dicern any difference here. Furthermore the hacks we have
to reconstruct this bit is a bit glaring, and probably only works
because we can't move the lvds port to any other pipe than pipe B on
gen2/3.
So let's just rip this out.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77137 (the LVDS
WARNING log, not the main "VGA can't be turned on" issue).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we always initialize kref for the context, even if we are using fake
contexts for hangstats when there is no hw support, we can forgo the
dance to dereference the ctx->obj and inspect whether we are permitted
to use kref inside i915_gem_context_reference() and _unreference().
My ulterior motive here is to improve the debugging of a use-after-free
of ctx->obj. This patch avoids the dereference here and instead forces
the assertion checks associated with kref.
v2: Refactor the fake contexts to being even more like the real
contexts, so that there is much less duplicated and special case code.
v3: Tweaks.
v4: Tweaks, minor.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76671
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: lu hua <huax.lu@intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[Jani: tiny change to backport to drm-intel-fixes.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Some machines use an external EC for controlling the backlight. Info
about this is present in the VBT. Do not setup native backlight control
if no PWM backlight is available or supported according to VBT. The
acpi_backlight interface appears to work for the EC control.
In most cases there has been no harm done, but it looks like there are
machines out there that have both an EC and our PWM line connected to
the same wire. This, obviously, does not end well.
This should fix the regression caused by
commit bc0bb9fd1c
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:14:29 2013 +0200
drm/i915: remove QUIRK_NO_PCH_PWM_ENABLE
AFAICT the quirk removed by the above commit effectively resulted in
i915 not driving the backlight PWM output, thus not messing things up.
Additionally this should fix the regression caused by
commit fbc9fe1b4f
Author: Aaron Lu <aaron.lu@intel.com>
Date: Fri Oct 11 21:27:45 2013 +0800
ACPI / video: Do not register backlight if win8 and native interface exists
which left some machines without a functioning backlight interface.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76276
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=47941
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=62281
CC: Aaron Lu <aaron.lu@intel.com>
CC: Eric Griffith <EGriffith92@gmail.com>
CC: Kent Baxley <kent.baxley@canonical.com>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The only supported types are none and PWM. Other values are obsolete or
reserved, don't add them.
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a requirement added to the spec. This patch will prevent
persistent corruption on the display.
v2: Make the wait before the vblank wait. (Art)
Try to finish early by polling the register
s/present/prevent (Chris)
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Upgrade debug output to ERROR.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch computes and stored 2nd M/N/TU for switching to different
refresh rate dynamically. PIPECONF_EDP_RR_MODE_SWITCH bit helps toggle
between alternate refresh rates programmed in 2nd M/N/TU registers.
v2: Daniel's review comments
Computing M2/N2 in compute_config and storing it in crtc_config
v3: Modified reference to edp_downclock and edp_downclock_avail based on the
changes made to move them from dev_private to intel_panel.
v4: Modified references to is_drrs_supported based on the changes made to
rename it to drrs_support.
v5: Jani's review comments
Removed superfluous return statements. Changed support for Gen 7 and above.
Corrected indentation. Re-structured the code which finds crtc and connector
from encoder. Changed some logs to be less verbose.
v6: Modifying i915_drrs to include only intel connector as intel_dp can be
derived from intel connector when required.
v7: As per internal review comments, acquiring mutex just before accessing
drrs RR. As per Chris's review comments, added documentation about the use
of locking in the function.
v8: Incorporated Jani's review comments.
Removed reference to edp_downclock.
v9: Jani's review comments. Modified comment in set_drrs. Changed index to
type edp_drrs_refresh_rate_type. Check if PSR is enabled before setting
registers fo DRRS.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch and finds out the lowest refresh rate supported for the resolution
same as the fixed_mode.
It also checks the VBT fields to see if panel supports seamless DRRS or not.
Based on above data it marks whether eDP panel supports seamless DRRS or not.
This information is needed for supporting seamless DRRS switch for certain
power saving usecases. This patch is tested by enabling the DRM logs and
user should see whether Seamless DRRS is supported or not.
v2: Daniel's review comments
Modified downclock deduction based on intel_find_panel_downclock
v3: Chris's review comments
Moved edp_downclock_avail and edp_downclock to intel_panel
v4: Jani's review comments.
Changed name of the enum edp_panel_type to drrs_support type.
Change is_drrs_supported to drrs_support of type enum drrs_support_type.
v5: Incorporated Jani's review comments
Modify intel_dp_drrs_initialize to return downclock mode. Support for Gen7
and above.
v6: Incorporated Chris's review comments.
Changed initialize to init in intel_drrs_initialize
v7: Incorporated Jani's review comments.
Removed edp_downclock and edp_downclock_avail. Return NULL explicitly.
Make drrs_state and unnamed struct. Move Gen based check inside drrs_init.
v8: Made changes to track PSR enable/disable throughout system use (instead
of just in the init sequence) for disabling/enabling DRRS. Jani's review
comments.
v9: PSR tracking will be done as part of idleness detection patch. Removed
PSR state tracker in i915_drrs. Jani's review comments.
v10: Added log for DRRS not supported in drrs_init
v11: Modification in drrs_init. suggested by Jani
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently it doesn't work. X-tiled self-refresh works flawlessly
otoh. Apparently X still works correctly with linear framebuffers, so
might just be an issue with the initial modeset. It's unclear whether
this just borked wm setup from our side or a hw restriction, but just
disabling gets things going.
Note that this regression was only brought to light with
commit 3f2dc5ac05
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Jan 10 14:06:47 2014 +0200
drm/i915: Fix 915GM self-refresh enable/disable
before that self-refresh for i915GM didn't work at all.
Kudos to Ville for spotting a little bug in the original patch I've
attached to the bug.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76103
Tested-by: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: rebase on top of drm-next with primary plane support.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Jesse's BIOS fb reconstruction code actually relies on the -ENOSPC
return value to detect overlapping framebuffers (which the bios uses
always when lighting up more than one screen). All this fanciness
happens in intel_alloc_plane_obj in intel_display.c.
Since no one else uses this we can safely remove the WARN without
repercussions.
Reported-by: Ben Widawsky <benjamin.widawsky@intel.com>
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 4b28a1f3ef.
This patch duct-tapes over some issue in the current bdw rps patches
which must wait with enabling rc6/rps until the very first batch has
been submitted by userspace.
But those patches aren't merged yet, and for upstream we need to have
an in-kernel emission of the very first batch. I shouldn't have
merged this patch so let's revert it again.
Also Imre noticed that even when rps is set up normally there's a
small window (due to the 1s delay of the async rps init work) where we
could runtime suspend already and blow up all over the place. Imre has
a proper fix to block runtime pm until the rps init work has
successfully completed.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We will treat Cherryview like Valleyview for most parts. Add a macro
for cases when we need to tell the two apart.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some MIPI panels might not have resolution which is a multiple of 64 like
1366x768. Enable this feature for such panels by default
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Though HS mode also should work.
v2: Change parameter as "bool hs" as suggested by Jani
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for Generic driver
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise, this can stall pipe. We also need DPLL REFA always
enabled
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As per the hw team's recommendation we need to enable the MIPI port
before enabling the plane and pipe. So call MIPI port enable in
pre_enable phase itself
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are additional registers needed for performance monitoring and
ARB_draw_indirect extensions in mesa.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76719
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Squash in fixup from Brad requested by Ken.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
haswell_write_eld() is also used on broadwell, so let's not explicitely
mention Haswell. The rest of the function has plenty of debug output
which will print the function name, so we know where we are anyway.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It is now clear that this interrupt is for the primary plane and not
something global to the pipe. It also matches what the spec calls it.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Piglit runner and QA are both looking at the dmesg for
DRM_ERRORs with test cases. Add a flag to control those
when we they are expected from related test cases.
Also add flag to control if contexts should be banned
that introduced the hang. Hangcheck is timer based and
preventing bans by adding sleeps to testcases makes
testing slower.
v2: intel_ring_stopped(), readable comment (Chris)
v3: keep compatibility (Daniel)
References: https://bugs.freedesktop.org/show_bug.cgi?id=75876
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since dma_buf_vunmap() procedes blithely on ignorant of whether the
driver failed to actually unmap the backing storage for the dma-buf, we
need to make a best-effort to do so. This involves not allowing
ourselves to be susceptible to signals causing us to leak the storage.
This should have been detectable with the current i-g-t as a misplaced
signal should have left the pages pinned upon freeing the object where
we have a warning in place.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Comment from Ben: It's a bit unclear whether we need this dance still
on bdw.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8 now has a qword to code for 48bit addresses.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems like it wouldn't be too unlikely to be wanting to use a an
expression in the macro argument and things could go very wrong.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Needs to happen after clock is running or it doesn't behave correctly.
v2: fix subject (Ville)
make it clearer that this occurs in pre_enable (Paulo)
misc bikesheds (Paulo)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allows sending of the null packets for conformance.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We also do a disable later when we write a specific infoframe, but here
we do it to prevent sending a stale one before updating the infoframes.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case we end up bouncing these around between ports.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We will have another use for the maximum watermark values that the
registers can hold. Pull those out into separate functions.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
