Add a reg property in the endpoint node as documented in
Documentation/devicetree/bindings/media/video-interfaces.txt
Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/isi@f8048000/port/endpoint@0 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The ISI is only present on the at91sam9g25, move the definition to the
at91sam9g25ek board dts to avoid warnings.
Solves the following warning for other 9x5ek boards:
Warning (unit_address_vs_reg): Node /ahb/apb/isi@f8048000 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Enable ISI and ov2640 for at91sam9g25ek board.
Meantime, we need to disable the mmc1 and spi0 as they have pin conflict
with ISI.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
to prepare the switch to the macro.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Macb0 node cannot be activated in generic sam9x5ek.dtsi file
as the sam9g15 does not have one.
Move the macb0 & macb1 activation in board .dts file that
support them.
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Set the dbgu pinctrl config by default as we have only one possible config
For other uart set the rxd/txd by default.
For at91sam9x5ek create soc based dts as we need to include specific soc dtsi.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Still use i2c-gpio on boards which have a SoC with a TWI IP which
doesn't have clock stretching in transmission mode.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Remove the malformed "mem=" bootargs parameter in at91sam9g25ek.dts
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Change vbus gpio configuration in .dts files to switch to
active low configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org>
make the ECHI depends on ARCH_AT91
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Device tree include file for the AT91SAM9x5 SoC family.
An additional .dtsi file is created to describe the generic
SAM9x5 CPU Module (CM).
Device tree source files for each Evaluation Kit that are using
the generic CPU Module and the carrier board. The selection of
available peripherals is done in this .dts file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
