In commit 02cea39586 ("genirq: Provide disable_hardirq()")
Peter introduced disable_hardirq() for netpoll, but it is forgotten
to use it for e1000.
This patch changes disable_irq() to disable_hardirq() for e1000.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Suggested-by: Sabrina Dubroca <sd@queasysnail.net>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .match_method field is a u8, so we shouldn't be casting to a u16,
and because it is only one byte, we do not need to byte swap anything.
Just assign the value directly. This avoids issues on Big Endian
architectures which would have byte swapped and then incorrectly
truncated the value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bimmy Pujari <bimmy.pujari@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of the cpts device found in the
gbe and 10gbe ethernet switches on the keystone 2 SoCs
(66AK2E/L/Hx, 66AK2Gx).
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.
Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.
This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").
So the new process is:
1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.
2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.
3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:
if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.
if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPPOL2TP_MSG_* and L2TP_MSG_* are duplicates, and are being used
interchangeably in the kernel, so let's standardize on L2TP_MSG_*
internally, and keep PPPOL2TP_MSG_* defined in UAPI for compatibility.
Signed-off-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the L2TP_MSG_* definitions to UAPI, as it is part of
the netlink API.
Signed-off-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lino Sanfilippo says:
====================
Remove private tx queue locks
this patch series removes unnecessary private locks in the sxgbe and the
stmmac driver.
v2:
- adjust commit message
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.
On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.
Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a private lock for synchronization of the xmit function and
the xmit completion handler, but since the NETIF_F_LLTX flag is not set,
the xmit function is also called with the xmit_lock held.
On the other hand the completion handler uses the reverse locking order by
first taking the private lock and (in case that the tx queue had been
stopped) then the xmit_lock.
Improve the locking by removing the private lock and using only the
xmit_lock for synchronization instead.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: bridge: fast ageing on topology change
802.1D [1] specifies that the bridges in a network must use a short
value to age out dynamic entries in the Filtering Database for a period,
once a topology change has been communicated by the root bridge.
This patchset fixes this for the in-kernel STP implementation.
Once the topology change flag is set in a net_bridge instance, the
ageing time value is shorten to twice the forward delay used by the
topology.
When the topology change flag is cleared, the ageing time configured for
the bridge is restored.
To accomplish that, a new bridge_ageing_time member is added to the
net_bridge structure, to store the user configured bridge ageing time.
Two helpers are added to offload the ageing time and set the topology
change flag in the net_bridge instance. Then the required logic is added
in the topology change helper if in-kernel STP is used.
This has been tested on the following topology:
+--------------+
| root bridge |
| 1 2 3 4 |
+--+--+--+--+--+
| | | | +--------+
| | | +------| laptop |
| | | +--------+
+--+--+--+-----+
| 1 2 3 |
| slave bridge |
+--------------+
When unplugging/replugging the laptop, the slave bridge (under test)
gets the topology change flag sent by the root bridge, and fast ageing
is triggered on the bridges. Once the topology change timer of the root
bridge expires, the topology change flag is cleared and the configured
ageing time is restored on the bridges.
A similar test has been done between two bridges under test.
When changing the forward delay of the root bridge with:
# echo 3000 > /sys/class/net/br0/bridge/forward_delay
the ageing time correctly changes on both bridges from 300s to 60s while
the TOPOLOGY_CHANGE flag is present.
[1] "8.3.5 Notifying topology changes",
http://profesores.elo.utfsm.cl/~agv/elo309/doc/802.1D-1998.pdf
No change since RFC: https://lkml.org/lkml/2016/10/19/828
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
802.1D [1] specifies that the bridges must use a short value to age out
dynamic entries in the Filtering Database for a period, once a topology
change has been communicated by the root bridge.
Add a bridge_ageing_time member in the net_bridge structure to store the
bridge ageing time value configured by the user (ioctl/netlink/sysfs).
If we are using in-kernel STP, shorten the ageing time value to twice
the forward delay used by the topology when the topology change flag is
set. When the flag is cleared, restore the configured ageing time.
[1] "8.3.5 Notifying topology changes ",
http://profesores.elo.utfsm.cl/~agv/elo309/doc/802.1D-1998.pdf
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a __br_set_topology_change helper to set the topology change value.
This can be later extended to add actions when the topology change flag
is set or cleared.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME switchdev attr is actually set
when initializing a bridge port, and when configuring the bridge ageing
time from ioctl/netlink/sysfs.
Add a __set_ageing_time helper to offload the ageing time to physical
switches, and add the SWITCHDEV_F_DEFER flag since it can be called
under bridge lock.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The channels are common for both ndevs in dual emac mode. Hence, keep
in sync their rates.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't re-split res in the following cases:
- speed of phys is not changed
- speed of phys is changed and no rate limited channels
- speed of phys is changed and all channels are rate limited
- phy is unlinked while dev is open
- phy is linked back but speed is not changed
The maximum speed is sum of "linked" phys, thus res are split taken
in account two interfaces, both for dual emac mode and for
switch mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-split weight along with budget. It simplify code a little
and update state after every rate change. Also it's necessarily
to move arguments checks to this combined function. Replace
maximum rate check for an interface on maximum possible rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to start queues after cpsw is started as it will be done
while cpsw_adjust_link(), after phy connection.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same, more convenient macros, to get active slave.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously relied on GENERIC_ALLOCATOR to be selected by CONFIG_ARM,
but now we can compile-test the driver on other architectures that
don't select it:
drivers/net/built-in.o: In function `mvneta_bm_remove':
mvneta_bm.c:(.text+0x4ee35): undefined reference to `gen_pool_free'
This adds an explicit select for the part of the driver that has
the dependency.
Fixes: a0627f776a ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a newline which was added
in socket.c file in net-next
Signed-off-by: Amit Kushwaha <kushwaha.a@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink_chain is called in ->release(), which is apparently
a process context, so we don't have to use an atomic notifier
here.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Fix pointer size when caam is used with AArch64 boot loader on
AArch32 kernel.
- Fix ahash state corruption in marvell driver.
- Fix buggy algif_aed tag handling.
- Prevent mcryptd from being used with incompatible algorithms which
can cause crashes"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif_aead - fix uninitialized variable warning
crypto: mcryptd - Check mcryptd algorithm compatibility
crypto: algif_aead - fix AEAD tag memory handling
crypto: caam - fix pointer size for AArch64 boot loader, AArch32 kernel
crypto: marvell - Don't corrupt state of an STD req for re-stepped ahash
crypto: marvell - Don't copy hash operation twice into the SRAM
Pull networking fixes from David Miller:
1) Limit the number of can filters to avoid > MAX_ORDER allocations.
Fix from Marc Kleine-Budde.
2) Limit GSO max size in netvsc driver to avoid problems with NVGRE
configurations. From Stephen Hemminger.
3) Return proper error when memory allocation fails in
ser_gigaset_init(), from Dan Carpenter.
4) Missing linkage undo in error paths of ipvlan_link_new(), from Gao
Feng.
5) Missing necessayr SET_NETDEV_DEV in lantiq and cpmac drivers, from
Florian Fainelli.
6) Handle probe deferral properly in smsc911x driver.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: mlx5: Fix Kconfig help text
net: smsc911x: back out silently on probe deferrals
ibmveth: set correct gso_size and gso_type
net: ethernet: cpmac: Call SET_NETDEV_DEV()
net: ethernet: lantiq_etop: Call SET_NETDEV_DEV()
vhost-vsock: fix orphan connection reset
cxgb4/cxgb4vf: Assign netdev->dev_port with port ID
driver: ipvlan: Unlink the upper dev when ipvlan_link_new failed
ser_gigaset: return -ENOMEM on error instead of success
NET: usb: cdc_mbim: add quirk for supporting Telit LE922A
can: peak: fix bad memory access and free sequence
phy: Don't increment MDIO bus refcount unless it's a different owner
netvsc: reduce maximum GSO size
drivers: net: cpsw-phy-sel: Clear RGMII_IDMODE on "rgmii" links
can: raw: raw_setsockopt: limit number of can_filter that can be set
Since the following commit, Infiniband and Ethernet have not been
mutually exclusive.
Fixes: 4aa17b28 mlx5: Enable mutual support for IB and Ethernet
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems attackers can also send UDP packets with no payload at all.
skb_condense() can still be a win in this case.
It will be possible to replace the custom code in tcp_add_backlog()
to get full benefit from skb_condense()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to get a regulator we may get deferred and we see
this noise:
smsc911x 1b800000.ethernet-ebi2 (unnamed net_device) (uninitialized):
couldn't get regulators -517
Then the driver continues anyway. Which means that the regulator
may not be properly retrieved and reference counted, and may be
switched off in case noone else is using it.
Fix this by returning silently on deferred probe and let the
system work it out.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
-----BEGIN PGP SIGNATURE-----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=HvKt
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Three fixes:
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:
"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.
We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."
We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.
Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Reviewed-by: David Dai <zdai@us.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
udp: receive path optimizations
This patch series provides about 100 % performance increase under flood.
v2: added Paolo feedback on udp_rmem_release() for tiny sk_rcvbuf
added the last patch touching sk_rmem_alloc later
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In flood situations, keeping sk_rmem_alloc at a high value
prevents producers from touching the socket.
It makes sense to lower sk_rmem_alloc only at the end
of udp_rmem_release() after the thread draining receive
queue in udp_recvmsg() finished the writes to sk_forward_alloc.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If udp_recvmsg() constantly releases sk_rmem_alloc
for every read packet, it gives opportunity for
producers to immediately grab spinlocks and desperatly
try adding another packet, causing false sharing.
We can add a simple heuristic to give the signal
by batches of ~25 % of the queue capacity.
This patch considerably increases performance under
flood by about 50 %, since the thread draining the queue
is no longer slowed by false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In UDP RX handler, we currently clear skb->dev before skb
is added to receive queue, because device pointer is no longer
available once we exit from RCU section.
Since this first cache line is always hot, lets reuse this space
to store skb->truesize and thus avoid a cache line miss at
udp_recvmsg()/udp_skb_destructor time while receive queue
spinlock is held.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Idea of busylocks is to let producers grab an extra spinlock
to relieve pressure on the receive_queue spinlock shared by consumer.
This behavior is requested only once socket receive queue is above
half occupancy.
Under flood, this means that only one producer can be in line
trying to acquire the receive_queue spinlock.
These busylock can be allocated on a per cpu manner, instead of a
per socket one (that would consume a cache line per socket)
This patch considerably improves UDP behavior under stress,
depending on number of NIC RX queues and/or RPS spread.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi says:
====================
net: qcom/emac: simplify support for different SOCs
On SOCs that have the Qualcomm EMAC network controller, the internal
PHY block is always different. Sometimes the differences are small,
sometimes it might be a completely different IP. Either way, using version
numbers to differentiate them and putting all of the init code in one
file does not scale.
This patchset does two things: The first breaks up the current code into
different files, and the second patch adds support for a third SOC, the
Qualcomm Technologies QDF2400 ARM Server SOC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The QDF2432 and the QDF2400 have slightly different internal PHYs,
so there are some programming differences. Some of the registers in
the QDF2400 have moved, and some registers require different values
during initialization.
Because of the differences, and because HIDs are a scare resource,
the ACPI tables specify the hardware version in an _HRV property.
Version 1 is the QDF2432, and version 2 is the QDF2400. Any future
SOC that has the same internal PHY but different programming
requirements will be assigned the next available version number.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal PHY of the EMAC differs on each SOC, and the list will
only continue to grow. By separating the code into individual files,
we can add support for more SOCs more cleanly.
Note: The internal PHY is also sometimes called the SGMII device.
We also stop referring to the various PHY variations by version number,
so no more "v2", "v3", etc. Instead, the devices are named after the
SOC they are, which is in sync with the device tree property names.
Future patches will probably rearrange more code among the files.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ldt->size can never be negative. The helper functions take 'unsigned int'
arguments which are assigned from ldt->size. The related user space
user_desc struct member entry_number is unsigned as well.
But ldt->size itself and a few local variables which are related to
ldt->size are type 'int' which makes no sense whatsoever and results in
typecasts which make the eyes bleed.
Clean it up and convert everything which is related to ldt->size to
unsigned it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
My static checker complains that we put an upper bound on the "size"
argument but not a lower bound. The checker is not smart enough to know
the possible ranges of "old_mm->context.ldt->size" from
init_new_context_ldt() so it thinks maybe it could be negative.
Let's make it unsigned to silence the warning and future proof the code
a bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: kernel-janitors@vger.kernel.org
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20161208105602.GA11382@elgon.mountain
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
One include less is always a good thing(tm). Good riddance.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-6-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reorganize the E400 detection now that we have everything in place:
switch the CPUs to broadcast mode after the LAPIC has been initialized
and remove the facilities that were used previously on the idle path.
Unfortunately static_cpu_has_bug() cannpt be used in the E400 idle routine
because alternatives have been applied when the actual detection happens,
so the static switching does not take effect and the test will stay
false. Use boot_cpu_has_bug() instead which is definitely an improvement
over the RDMSR and the cpumask handling.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-5-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
AMD CPUs affected by the E400 erratum suffer from the issue that the
local APIC timer stops when the CPU goes into C1E. Unfortunately there
is no way to detect the affected CPUs on early boot. It's only possible
to determine the range of possibly affected CPUs from the family/model
range.
The actual decision whether to enter C1E and thus cause the bug is done
by the firmware and we need to detect that case late, after ACPI has
been initialized.
The current solution is to check in the idle routine whether the CPU is
affected by reading the MSR_K8_INT_PENDING_MSG MSR and checking for the
K8_INTP_C1E_ACTIVE_MASK bits. If one of the bits is set then the CPU is
affected and the system is switched into forced broadcast mode.
This is ineffective and on non-affected CPUs every entry to idle does
the extra RDMSR.
After doing some research it turns out that the bits are visible on the
boot CPU right after the ACPI subsystem is initialized in the early
boot process. So instead of polling for the bits in the idle loop, add
a detection function after acpi_subsystem_init() and check for the MSR
bits. If set, then the X86_BUG_AMD_APIC_C1E is set on the boot CPU and
the TSC is marked unstable when X86_FEATURE_NONSTOP_TSC is not set as it
will stop in C1E state as well.
The switch to broadcast mode cannot be done at this point because the
boot CPU still uses HPET as a clockevent device and the local APIC timer
is not yet calibrated and installed. The switch to broadcast mode on the
affected CPUs needs to be done when the local APIC timer is actually set
up.
This allows to cleanup the amd_e400_idle() function in the next step.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-4-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The workaround for the AMD Erratum E400 (Local APIC timer stops in C1E
state) is a two step process:
- Selection of the E400 aware idle routine
- Detection whether the platform is affected
The idle routine selection happens for possibly affected CPUs depending on
family/model/stepping information. These range of CPUs is not necessarily
affected as the decision whether to enable the C1E feature is made by the
firmware. Unfortunately there is no way to query this at early boot.
The current implementation polls a MSR in the E400 aware idle routine to
detect whether the CPU is affected. This is inefficient on non affected
CPUs because every idle entry has to do the MSR read.
There is a better way to detect this before going idle for the first time
which requires to seperate the bug flags:
X86_BUG_AMD_E400 - Selects the E400 aware idle routine and
enables the detection
X86_BUG_AMD_APIC_C1E - Set when the platform is affected by E400
Replace the current X86_BUG_AMD_APIC_C1E usage by the new X86_BUG_AMD_E400
bug bit to select the idle routine which currently does an unconditional
detection poll. X86_BUG_AMD_APIC_C1E is going to be used in later patches
to remove the MSR polling and simplify the handling of this misfeature.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-3-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Will be used in a later patch to set bug bits for bugs which need late
detection.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/20161209182912.2726-2-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull libnvdimm fixes from Dan Williams:
"Several fixes to the DSM (ACPI device specific method) marshaling
implementation.
I consider these urgent enough to send for 4.9 consideration since
they fix the kernel's handling of ARS (Address Range Scrub) commands.
Especially for platforms without machine-check-recovery capabilities,
successful execution of ARS commands enables the platform to
potentially break out of an infinite reboot problem if a media error
is present in the boot path. There is also a one line fix for a
device-dax read-only mapping regression.
Commits 9a901f5495 ("acpi, nfit: fix extended status translations
for ACPI DSMs") and 325896ffdf ("device-dax: fix private mapping
restriction, permit read-only") are true regression fixes for changes
introduced this cycle.
Commit efda1b5d87 ("acpi, nfit, libnvdimm: fix / harden ars_status
output length handling") fixes the kernel's handling of zero-length
results, this never would have worked in the past, but we only just
recently discovered a BIOS implementation that emits this arguably
spec non-compliant result.
The remaining two commits are additional fall out from thinking
through the implications of a zero / truncated length result of the
ARS Status command.
In order to mitigate the risk that these changes introduce yet more
regressions they are backstopped by a new unit test in commit
a7de92dac9 ("tools/testing/nvdimm: unit test acpi_nfit_ctl()") that
mocks up inputs to acpi_nfit_ctl()"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix private mapping restriction, permit read-only
tools/testing/nvdimm: unit test acpi_nfit_ctl()
acpi, nfit: fix bus vs dimm confusion in xlat_status
acpi, nfit: validate ars_status output buffer size
acpi, nfit, libnvdimm: fix / harden ars_status output length handling
acpi, nfit: fix extended status translations for ACPI DSMs
Pull libata fixes from Tejun Heo:
"This is quite late but SCT Write Same support added during this cycle
is broken subtly but seriously and it'd be best to disable it before
v4.9 gets released.
This contains two commits - one low impact sata_mv fix and the
mentioned disabling of SCT Write Same"
* 'for-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata-scsi: disable SCT Write Same for the moment
ata: sata_mv: check for errors when parsing nr-ports from dt
kernel crashes. Marked for stable - it goes back to 4.6, but started
popping up only in 4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJYSo2yAAoJEEp/3jgCEfOLa1UH/j/nhhmy6bkvNTNQT9PuWmlu
1cGG6JkJq/USEaSO+VXGSAjBCjCngNTYYXBo0IBCnkf11tuwagvz/9LSbvy9P+vu
1IKwcJBFpgcEMEZWsYjVui9uFiDcLYiTPt4pux4tQ4vyj6HEFgioTg/430ApUEOS
ywO1pjRz8RH0FlKhhcTRGOwVcwUzI/aRw7aLeflSwz3mDnh6ajp/8pjvxWf7AN+V
Ih9LygjYNb4IdUcgN2G05z2qKLPfNAoBA+kRdEkOzecX2J0Db8Bu1bfZBxgOK+ui
kpdVlFPkpULbwjlLLpvmOgy7FKgmLfdxuEuQol8hCu0KQ+buP/kZnbjg6QBeCtk=
=1nK/
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.9-rc9' of git://github.com/ceph/ceph-client
Pull ceph fix from Ilya Dryomov:
"A fix for an issue with ->d_revalidate() in ceph, causing frequent
kernel crashes.
Marked for stable - it goes back to 4.6, but started popping up only
in 4.8"
* tag 'ceph-for-4.9-rc9' of git://github.com/ceph/ceph-client:
ceph: don't set req->r_locked_dir in ceph_d_revalidate
A few fixes that have trickled in over the last week, all fixing minor
errors in devicetrees -- UART pin assignment on Allwinner H3, correcting
number of SATA ports on a Marvell-based Linkstation platform and a display
clock fix for Freescale/NXP i.MX7D that fixes a freeze when starting up X.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sper
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Final batch of SoC fixes
A few fixes that have trickled in over the last week, all fixing minor
errors in devicetrees -- UART pin assignment on Allwinner H3,
correcting number of SATA ports on a Marvell-based Linkstation
platform and a display clock fix for Freescale/NXP i.MX7D that fixes a
freeze when starting up X"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: orion5x: fix number of sata port for linkstation ls-gl
ARM: dts: imx7d: fix LCDIF clock assignment
dts: sun8i-h3: correct UART3 pin definitions
