These counters are used for Displayort compliance testing to detect error
conditions when executing tests 4.2.2.4 and 4.2.2.5 in the Displayport Link
CTS specificaiton. They determine whether to use the preferred/requested
mode or the failsafe mode during these tests.
V2:
- Addressed previous review feedback
- Updated commit message
- Changed from uint8_t to uint32_t
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Todd Previte <tprevite@gmail.com>
[danvet: s/uint32_t/unsigned/ for clearer intent. Also drop the i915
from the subject, it's all core stuff.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since commit 89168b4899 ("mmc: core: restore detect line inversion
semantics"), the SD card on i.MX28 (and possibly other) devices isn't
detected and booting stops at:
[ 4.120617] Waiting for root device /dev/mmcblk0p3...
This is caused by the MMC_CAP2_CD_ACTIVE_HIGH flag being set incorrectly
when the host controller doesn't use a GPIO for card detection (but
instead uses a dedicated pin). In this case mmc_gpiod_request_cd() will
return before assigning to the gpio_invert variable, leaving the
variable uninitialized. The variable then gets used to set the flag.
This patch fixes the issue by making sure gpio_invert is set to false
when a GPIO isn't used. After this patch, i.MX28 boots fine.
The MMC_CAP2_RO_ACTIVE_HIGH (write protect) flag is also set incorrectly
for the exact same reason (it uses the same uninitialized variable), so
this patch fixes that too.
Fixes: 89168b4899 ("mmc: core: restore detect line inversion semantics")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Without the fix, the mute led can't work on these three machines.
After apply this fix, these three machines will fall back on the led
control quirk as below, and through testing, the mute led works very
well.
PIN_QUIRK(0x10ec0282, 0x103c, "HP", ALC269_FIXUP_HP_LINE1_MIC1_LED,
ALC282_STANDARD_PINS,
{0x12, 0x90a60140},
...
BugLink: https://bugs.launchpad.net/bugs/1389497
Tested-by: TieFu Chen <tienfu.chen@canonical.com>
Cc: Kailang Yang <kailang@realtek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add Lee Jones as a new co-maintainer.
The kernel.org repo moved to allow us both to push to it. Update
MAINTAINERS to match.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix a regression on Vybrid platform which is caused by commit
dc4805c2e7 (ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3
driver), and results in a missing configuration on PLL clocks.
- Fix a regression with i.MX defconfig files where CONFIG_SPI option
gets lost accidentally.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUWLLbAAoJEFBXWFqHsHzOCJcH/Rm1q8mIjhHN7Q9k0cYeKuM2
r59Cyl1nJt+nG6qgPK+hPOl3Lw8z9c7zLJ/TG6wsNrAOaFNfNGs3npytL2S6iyDM
KX7IulltuA5Sl5JBXXyMYzn+nm5jBnFrnX/6IUQFI7OB0WVGWOzfyKeqEMzPnG5x
CApc8YHNKe0HBvDyYHkRlNrwwJjVCB2V6H86Km4QsRkTvSkiYa+Fuf1o9M9gpBg9
4wWq9WekFizb0uVTk9tBMcoX82Y/GD6/52MDW2ISGhAVWavxJ2O+UhrdSSmrPqC2
7LY0C6t1YAFZKLn0yn9sAyubG5P/MZF8UAs+7go2s1vtCbG3RvoxPz6RxkEyrmY=
=KnLU
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.18, 2nd round" from Shawn Guo:
"This is the second round of i.MX fixes for 3.18. The clk-vf610 fix is
relatively big, because it needs some adaption to the change made by
offending commit dc4805c2e7 (ARM: imx: remove ENABLE and BYPASS bits
from clk-pllv3 driver). And it should have been sent to you for earlier
-rc inclusion, but unfortunately it got delayed for some time because
Stefan wasn't aware of my email address change."
The i.MX fixes for 3.18, 2nd round:
- Fix a regression on Vybrid platform which is caused by commit
dc4805c2e7 (ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3
driver), and results in a missing configuration on PLL clocks.
- Fix a regression with i.MX defconfig files where CONFIG_SPI option
gets lost accidentally.
* tag 'imx-fixes-3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (460 commits)
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
+ Linux 3.18-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
I've tried to cc all the people who have recently added new stuff
but forgotten to update documentation.
I've also decided not to bother documenting the massive property list
in struct drm_mode_config. If that beast keeps on growing we might want
to extract it into a separate structure which we won't document.
Cc: Thomas Wood <thomas.wood@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
While writing atomic docs I've noticed that I don't get any errors
for my screw-ups in drm_crtc.h. Fix this immediately.
This just does the bare minimum to get starts, lots of stuff isn't
properly documented yet unfortunately.
v2: Fix adjacent spelling error Sean noticed.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just a bit of OCD cleanup on headers - this function isn't the core
interface any more but just a helper for drivers who haven't yet
transitioned to universal planes. Put the declaration at the right
spot and sprinkle necessary #includes over all drivers.
Maybe this helps to encourage driver maintainers to do the switch.
v2: Fix #include ordering for tegra, reported by 0-day builder.
v3: Include required headers, reported by Thierry.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Pull thermal fixes from Eduardo Valentin:
"Specifics:
- a few code fixes improving the Exynos code base. They remove dead
and unreachable code. No functional changes here
- in Exynos code base, fixes regarding the right usage of features
(TRIMINFO and TRIMRELOAD)
- documentation of RCAR thermal
- fix in the of-thermal, regarding the proper usage of of-APIs
- fixes on thermal-core, removal of unreachable code"
[ Eduardo is sending the thermal fixes on behalf of Rui Zhang this time.
Rui is currently unable to send pull requests due to troubles with his
machine and he's currently in a business trip ]
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
Thermal:Remove usless if(!result) before return tz
thermal: exynos: fix IRQ clearing on TMU initialization
thermal: fix multiple disbalanced device node counters
thermal: rcar: Add binding docs for new R-Car Gen2 SoCs
thermal: exynos: Add support for TRIM_RELOAD feature at Exynos3250
thermal: exynos: Add support for many TRIMINFO_CTRL registers
thermal: samsung: Exynos5260 and Exynos5420 should not use TRIM_RELOAD flag
thermal: exynos: remove identical values from exynos*_tmu_registers structures
thermal: exynos: remove redundant pdata checks from exynos_tmu_control()
thermal: exynos: cache non_hw_trigger_levels in pdata
thermal: exynos: simplify temp_to_code() and code_to_temp()
thermal: exynos: remove redundant threshold_code checks from exynos_tmu_initialize()
thermal: exynos: remove redundant pdata checks from exynos_tmu_initialize()
thermal: exynos: remove dead code for HW_MODE calibration
thermal: exynos: remove unused struct exynos_tmu_registers entries
Quirks and DMI match additions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUWHINAAoJEKbMaAwKp364uGUH/jfm+247uKXYGUy/FfbpxGNt
3RQwswAWmg/3urVmMeIQhQntc/rMXwPh0knhyrCXgL9ZdCCTfJQ1ChT67mPoVcEN
moJq82RrRwq5jKPYgoj4iVSBvyMY1c4Ydht/9jyzhHIUE7ro4P8lOEKw6BCFCctm
l32zi4rqt3o5ES2IMV9vRW76Y4Z47ijgHKvi2mWwjgva75aGlaPm6IDoU1qpaMG0
wDVcwvV66YeELon5Uh8gLQzBLZy5ctMTyCALwiLF89I3BZw9/OBy+gLxDaLq8jCW
8ZBKqM7+2ZQd6kc3Tgi1jygdpFTfWaDtof9AsdzeqRYljP3ZCI4AUU2sjbZ1jvY=
=WJnO
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v3.18-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform drievr updates from Darren Hart:
"A short list of patches applying quirks and new DMI matches. These
pass my basic build tests and have spent 4 days in linux-next"
* tag 'platform-drivers-x86-v3.18-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
quirk for Lenovo Yoga 3: no rfkill switch
acer-wmi: Add acpi_backlight=video quirk for the Acer KAV80
samsung-laptop: Add broken-acpi-video quirk for NC210/NC110
asus-nb-wmi: Add wapf4 quirk for the X550VB
toshiba_acpi: Add Toshiba TECRA A50-A to the alt keymap dmi list
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes if you please"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc: use device_online/offline() instead of cpu_up/down()
powerpc/powernv: Properly fix LPC debugfs endianness
powerpc: do_notify_resume can be called with bad thread_info flags argument
powerpc/fadump: Fix endianess issues in firmware assisted dump handling
powerpc: Fix section mismatch warning
mounted in two locations caused the ftracetests to fail. This is because
the ftracetests script does a grep of the /proc/mounts file to find
where the debugfs file system is mounted. If it is mounted twice, then
the grep returns two lines instead of just one. This causes the ftracetests
to get confused and fail.
Use "head -1" to only return the first mount point for debugfs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUV812AAoJEEjnJuOKh9ldquIIAK1DeSn6QQrA2qytqZmaW/dh
M1QiG+Ot5Qh7+qli7Sun5E58jbMvclPCiHrtr44KEGDSzABrjjv8TnqCwI9XKfiO
hn9IGFy2gCU7jNMdE+1MRPwykVwLjYBZLaLyxY/WvwJTtlPORezq7KTdvUPgobCN
hQfxPyowofbGTsV9+75olSo9ercOKGv4NSopY2fj6fag185emUDLT4GGWGsWh/1j
heUhe4vYuuB43YAVgk+XeJEOQ8u4uME9lTocuykISazXupZo4+RfZzQPziD5Q/Mt
LuOg4zUpG7fX2AkECXvTR055CcCVVHKUTBZppIpeKqfAXBU6GeoaP1AM2CDx72I=
=jKWc
-----END PGP SIGNATURE-----
Merge tag 'ftracetest-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftracetest fix from Steven Rostedt:
"Running the ftracetests on a machine that had the debugfs file system
mounted in two locations caused the ftracetests to fail. This is
because the ftracetests script does a grep of the /proc/mounts file to
find where the debugfs file system is mounted. If it is mounted
twice, then the grep returns two lines instead of just one. This
causes the ftracetests to get confused and fail.
Use "head -1" to only return the first mount point for debugfs"
* tag 'ftracetest-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftracetest: Take the first debugfs mount found
If we hit any errors in btrfs_lookup_csums_range, we'll loop through all
the csums we allocate and free them. But the code was using list_entry
incorrectly, and ended up trying to free the on-stack list_head instead.
This bug came from commit 0678b6185
btrfs: Don't BUG_ON kzalloc error in btrfs_lookup_csums_range()
Signed-off-by: Chris Mason <clm@fb.com>
Reported-by: Erik Berg <btrfs@slipsprogrammoer.no>
cc: stable@vger.kernel.org # 3.3 or newer
We were returning maxlen like the userland strnlen if no '\0' character
was encountered while the kernel version is expected to return a value
larger than maxlen. Fixed to return maxlen + 1.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 64546e9fe3 ("ARM: imx_v6_v7_defconfig updates") and commit
0650f855d2 ("ARM: imx_v4_v5_defconfig: Select CONFIG_IMX_WEIM") CONFIG_SPI
selection was dropped by savedefconfig for imx_v4_v5_defconfig and
imx_v6_v7_defconfig.
In order to keep the same behaviour as previous kernel versions and avoid
regressions, let's add CONFIG_SPI option back.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There are only 4 CTAR registers (CTAR0 - CTAR3) so we can only use the
lower 2 bits of the chip select to select a CTAR register.
SPI_PUSHR_CTAS used the lower 3 bits which would result in wrong bit values
if the chip selects 4/5 are used. For those chip selects SPI_CTAR even
calculated offsets of non-existing registers.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The string property read helpers will run off the end of the buffer if
it is handed a malformed string property. Rework the parsers to make
sure that doesn't happen. At the same time add new test cases to make
sure the functions behave themselves.
The original implementations of of_property_read_string_index() and
of_property_count_strings() both open-coded the same block of parsing
code, each with it's own subtly different bugs. The fix here merges
functions into a single helper and makes the original functions static
inline wrappers around the helper.
One non-bugfix aspect of this patch is the addition of a new wrapper,
of_property_read_string_array(). The new wrapper is needed by the
device_properties feature that Rafael is working on and planning to
merge for v3.19. The implementation is identical both with and without
the new static inline wrapper, so it just got left in to reduce the
churn on the header file.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darren Hart <darren.hart@intel.com>
Cc: <stable@vger.kernel.org> # v3.3+: Drop selftest hunks that don't apply
modeset->num_connectors must be 0 to reach the BUG_ON() which tests
for non-zero modeset->num_connectors; remove BUG_ON().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A connector may be forced on from the command line via video=
command line setting. The digital output of dual-mode connectors
can also be specifically selected and forced on; eg., 'video=DVI-I-2:D'.
However, in this case, the connector->status will be mistakenly set to
connector_status_disconnected, and the connector will not be mode set.
Fix the connector->status when connector->force is DRM_FORCE_ON_DIGITAL.
Note that this seems to have been broken ever since the introduction
of the connector forcing support in
commit d50ba256b5
Author: Dave Airlie <airlied@linux.ie>
Date: Wed Sep 23 14:44:08 2009 +1000
drm/kms: start adding command line interface using fb.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
[danvet: Add note about that this never worked.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So far, the required PLL's (PLL1/PLL2/PLL5) have been initialized
by boot loader and the kernel code defined fixed rates according
to those default configurations. Beginning with the USB PLL7 the
code started to initialize the PLL's itself (using imx_clk_pllv3).
However, since commit dc4805c2e7
(ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver)
imx_clk_pllv3 no longer takes care of the ENABLE and BYPASS bits,
hence the USB PLL were not configured correctly anymore.
This patch not only fixes those USB PLL's, but also makes use of
the imx_clk_pllv3 for all PLL's and alignes the code with the PLL
support of the i.MX6 series.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
- Two fixes for the Baytrail driver affecting IRQs and
output state in sysfs
- Use the linux-gpio mailing list also for pinctrl patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dbx2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin-control fixes from Linus Walleij:
"This kernel cycle has been calm for both pin control and GPIO so far
but here are three pin control patches for you anyway, only really
dealing with Baytrail:
- Two fixes for the Baytrail driver affecting IRQs and output state
in sysfs
- Use the linux-gpio mailing list also for pinctrl patches"
* tag 'pinctrl-v3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: baytrail: show output gpio state correctly on Intel Baytrail
pinctrl: use linux-gpio mailing list
pinctrl: baytrail: Clear DIRECT_IRQ bit
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"This contains important fixes for recently introduced highmem support
for default contiguous memory region used for dma-mapping subsystem"
* 'fixes-for-v3.18' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
mm, cma: make parameters order consistent in func declaration and definition
mm: cma: Use %pa to print physical addresses
mm: cma: Ensure that reservations never cross the low/high mem boundary
mm: cma: Always consider a 0 base address reservation as dynamic
mm: cma: Don't crash on allocation if CMA area can't be activated
It is safe to call notify disconnect when the usb core
thinks the device is disconnected.
This commit also fixes one bug found at below situation:
we have not enabled usb wakeup, we do system suspend when
there is an usb device at the port, after suspend, we plug out
the usb device, then plug in device again. At that time,
the nofity disconnect was not called at current code, as
the controller doesn't know the usb device was disconnected
during the suspend, but USB core knows the port has changed
during that periods.
So to fix this problem, and let the usb core call notify disconnect.
Cc: 3.17+ <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we notify disconnecting based on the usb device is existed
(port_dev->child, the child device at roothub is not NULL), we
need to notify connect after device has been registered.
This fixes a bug that do fast plug in/out test, and the notify_disconnect
is not called due to roothub child is NULL and the enumeration has failed.
Cc: v3.17+ <stable@vger.kernel.org>
Signed-off-by: Tony Zheng <Tony.Zheng@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently this quirk is enabled for the model with the device id 0x0089, it
is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904
as well.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbip driver was moved out of staging in 3.17-rc3 but the MAINTAINERS file
still has the old staging entry as well as the new one. Remove the old entry.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions fw5895_init() and config_autodelink_before_power_down() are used
only when CONFIG_PM is defined.
drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function]
drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PLAT_S5P Kconfig symbol was removed in commit d78c16ccde
("ARM: SAMSUNG: Remove remaining legacy code"). There are still
some references left, fix that by replacing them with ARCH_S5PV210.
Fixes: d78c16ccde ("ARM: SAMSUNG: Remove remaining legacy code")
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like some Seagate enclosures, these devices do not seem to grok ata
pass through commands.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk
which is known to work fine with other controllers causes the system to freeze
when connected over usb-3 with this controller, where as it works fine with
uas in usb-2 ports, indicating a problem with streams.
This is a bit bigger hammer then I would like to use for this, but for now it
will have to make do. I've ordered a pci-e usb controller card with an Asmedia
1042, once that arrives I'll try to get streams to work (with a quirk flag if
necessary) and then we can re-enable them. For now this at least makes uas
capable disk enclosures work again by forcing fallback to the usb-storage
driver.
Reported-by: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We wanted to print the version as (major).(minor) but because the shift
operation is higher precedence than the mask then we print
(minor).(minor).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Tested-by: Paul Osmialowski <newchief@king.net.pl>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the following oops:
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver wasn't properly configuring the hardware for the current
termios settings under all conditions. Ensure that termios are
written to the device when the port is activated.
Signed-off-by: Jim Paris <jim@jtan.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device-id entry for GW Instek AFG-2225, which has a byte swapped
bInterfaceSubClass (0x20).
Reported-by: Karl Palsson <karlp@tweak.net.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ceph fixes from Sage Weil:
"There is a GFP flag fix from Mike Christie, an error code fix from
Jan, and fixes for two unnecessary allocations (kmalloc and workqueue)
from Ilya. All are well tested.
Ilya has one other fix on the way but it didn't get tested in time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: eliminate unnecessary allocation in process_one_ticket()
rbd: Fix error recovery in rbd_obj_read_sync()
libceph: use memalloc flags for net IO
rbd: use a single workqueue for all devices
result is always zero when comes here.
Signed-off-by: Yao Dongdong <yaodongdong@huawei.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull m68k update from Geert Uytterhoeven.
Just wiring up the bpf system call.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up bpf
A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd say.
Anyway, most of this are a few defconfig updates. Some for omap to deal
with kernel binary size (moving ipv6 to module, etc). A larger one for
socfpga that refreshes with some churn, but also turns on a few options
that makes the newly-added board in my bootfarm usable for testing.
OMAP3 will also now warn when booted with legacy (non-DT) boot protocols,
hopefully encouraging those who still care about some of those platforms
to submit DT support and report bugs where needed. Nothing stops working
though, this is just to warn for future deprecation.
Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot hangs,
a missing terminting entry in a dt_match array on RealView a MTD fix on
OMAP with NAND.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JasG
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A surprisingly small batch of fixes for -rc3. Suspiciously small, I'd
say.
Anyway, most of this are a few defconfig updates. Some for omap to
deal with kernel binary size (moving ipv6 to module, etc). A larger
one for socfpga that refreshes with some churn, but also turns on a
few options that makes the newly-added board in my bootfarm usable for
testing.
OMAP3 will also now warn when booted with legacy (non-DT) boot
protocols, hopefully encouraging those who still care about some of
those platforms to submit DT support and report bugs where needed.
Nothing stops working though, this is just to warn for future
deprecation.
Beyond this, very few actual bugfixes. A PXA fix for DEBUG_LL boot
hangs, a missing terminting entry in a dt_match array on RealView a
MTD fix on OMAP with NAND"
[ Obviously missed rc3, will make rc4 instead ;) ]
* tag 'armsoc-for-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: drop list entry for davinci
ARM: OMAP2+: Warn about deprecated legacy booting mode
ARM: omap2plus_defconfig: Fix errors with NAND BCH
ARM: multi_v7_defconfig: fix support for APQ8084
soc: versatile: Add terminating entry for realview_soc_of_match
ARM: ixp4xx: remove compilation warnings in io.h
MAINTAINERS: Add Soren as reviewer for Zynq
ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in
ARM: socfpga_defconfig: Update defconfig for SoCFPGA
ARM: pxa: fix hang on startup with DEBUG_LL
- suspend/resume/freeze/thaw unification from Imre
- wa list improvements from Mika&Arun
- display pll precomputation from Ander Conselvan, this removed the last
->mode_set callbacks, a big step towards implementing atomic modesets
- more kerneldoc for the interrupt code
- 180 rotation for cursors (Ville&Sonika)
- ULT/ULX feature check macros cleaned up thanks to Damien
- piles and piles of fixes all over, bug team seems to work!
* tag 'drm-intel-next-2014-10-24' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20141024
drm/i915: add comments on what stage a given PM handler is called
drm/i915: unify switcheroo and legacy suspend/resume handlers
drm/i915: add poweroff_late handler
drm/i915: sanitize suspend/resume helper function names
drm/i915: unify S3 and S4 suspend/resume handlers
drm/i915: disable/re-enable PCI device around S4 freeze/thaw
drm/i915: enable output polling during S4 thaw
drm/i915: check for GT faults in all resume handlers and driver load time
drm/i915: remove unused restore_gtt_mappings optimization during suspend
drm/i915: fix S4 suspend while switcheroo state is off
drm/i915: vlv: fix switcheroo/legacy suspend/resume
drm/i915: propagate error from legacy resume handler
drm/i915: unify legacy S3 suspend and S4 freeze handlers
drm/i915: factor out i915_drm_suspend_late
drm/i915: Emit even number of dwords when emitting LRIs
drm/i915: Add rotation support for cursor plane (v5)
drm/i915: Correctly reject invalid flags for wait_ioctl
drm/i915: use macros to assign mmio access functions
drm/i915: only run hsw_power_well_post_enable when really needed
...
drivers/media/dvb-frontends/sp2.c:269:5: sparse: symbol 'sp2_init' was not declared. Should it be static?
drivers/media/dvb-frontends/sp2.c:351:5: sparse: symbol 'sp2_exit' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Running ftracetests on a box that mounted debugfs in two locations
made the ftracetests fail. This is because the tests uses a grep
of debugfs from the /proc/mounts file to find the debugfs mount
point, and then appends "/tracing" to that string to get the tracing
directory.
If the debugfs directory is mounted twice, then that grep will return
two answers and appending "/tracing" to a string with two lines will
not work.
Use "head -1" to only take the first mount point found.
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The default used to be that the first vivid device instance was
single planar, the second multi planar, the third single planar, etc.
However, that turned out to be unexpected and awkward. Change the
driver to always default to single planar.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
