from Tero Kristo <t-kristo@ti.com>.
This sets gets us into a better position for further clean-up:
- Gets PRCM code closer to being device drivers
- Allows to move the remainig clock code to drivers/clk for v4.2
- Starts enforcing interconnect hierarchy in the SoC specific .dts
files to enforce device drivers are only accesing registers in
the related hardware module
This patchset has seen quite a few revisions but did not come into
mergeable shape until recently. As other patchsets for clock specific
device drivers depend on this, it would be good to get this merged
although it's a bit late for the v4.1 merge window.
Note that as the device entries in the .dts files are moved around,
this is based on earlier non-urgent fixes to avoid a non-trivial
merge conflict.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jiqd
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/prcm-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/late
Pull "Clean-up for omap PRCM (Power Reset Clock Management) and interconnects" from Tony Lindgren
Patches originally from Tero Kristo <t-kristo@ti.com>.
This sets gets us into a better position for further clean-up:
- Gets PRCM code closer to being device drivers
- Allows to move the remainig clock code to drivers/clk for v4.2
- Starts enforcing interconnect hierarchy in the SoC specific .dts
files to enforce device drivers are only accesing registers in
the related hardware module
This patchset has seen quite a few revisions but did not come into
mergeable shape until recently. As other patchsets for clock specific
device drivers depend on this, it would be good to get this merged
although it's a bit late for the v4.1 merge window.
Note that as the device entries in the .dts files are moved around,
this is based on earlier non-urgent fixes to avoid a non-trivial
merge conflict.
* tag 'omap-for-v4.1/prcm-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (44 commits)
ARM: OMAP4+: control: add support for initializing control module via DT
ARM: dts: dra7: add minimal l4 bus layout with control module support
ARM: dts: omap5: add minimal l4 bus layout with control module support
ARM: OMAP4+: control: remove support for legacy pad read/write
ARM: OMAP4: display: convert display to use syscon for dsi muxing
ARM: dts: omap4: add minimal l4 bus layout with control module support
ARM: dts: am4372: add minimal l4 bus layout with control module support
ARM: dts: am43xx-epos-evm: fix pinmux node layout
ARM: dts: am33xx: add minimal l4 bus layout with control module support
ARM: dts: omap3: add minimal l4 bus layout with control module support
ARM: dts: omap24xx: add minimal l4 bus layout with control module support
ARM: OMAP2+: control: add syscon support for register accesses
ARM: OMAP2+: id: cache omap_type value
ARM: OMAP2+: control: remove API for getting control module base address
ARM: OMAP2+: clock: add low-level support for regmap
ARM: OMAP4+: PRM: get rid of cpu_is_omap44xx calls from interrupt init
ARM: OMAP4+: PRM: setup prm_features from the PRM init time flags
ARM: OMAP2+: CM: move SoC specific init calls within a generic API
ARM: OMAP4+: PRM: determine prm_device_inst based on DT compatibility
ARM: OMAP2+: PRM: move SoC specific init calls within a generic API
...
OMAP4, OMAP5 and DRA7 now parse DT entries for control module address spaces,
and set up syscon mappings appropriately. Low level IO init is updated to
remove the legacy control module mappings for these devices also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates the l4_cfg and l4_wkup interconnects for DRA7, and
moves some of the generic peripherals under it. System control module
support is added to the device tree also, and the existing SCM related
functionality is moved under it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates the l4_cfg and l4_wkup interconnects for OMAP5, and
moves some of the generic peripherals under it. System control module
support is added to the device tree also, and the existing SCM related
functionality is moved under it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
omap4_ctrl_pad_readl/writel are no longer used by anybody, so remove
these. Syscon / pinctrl should be used to access the padconf area
instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The legacy control module APIs will be gone, thus convert the display
driver to use syscon. This change should eventually be moved to
display driver from the board directory.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch creates the l4_cfg and l4_wkup interconnects for OMAP4, and
moves some of the generic peripherals under it. System control module
support is added to the device tree also, and the existing SCM related
functionality is moved under it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
This patch creates an l4_wkup interconnect for AM43xx, and moves some of
the generic peripherals under it. System control module nodes are moved
under this new interconnect also, and the SCM clock layout is changed
to use the renamed SCM nodea as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Pinmux node should be a reference to the base one, not a complete re-write
of it. Having the node like this also prevents modifying the node layout
in the base am4372.dtsi file, which is needed for control module changes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates an l4_wkup interconnect for AM33xx, and moves some of
the generic peripherals under it. System control module nodes are moved
under this new interconnect also, and the SCM clock layout is changed
to use the renamed SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This patch creates an l4_core interconnect for OMAP3, and moves some
of the generic peripherals under it. System control module nodes are
moved under this new interconnect also, and the SCM clock layout
is changed to use the renamed SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
This patch creates an l4 / l4-wkup interconnects for omap2420 / omap2430
SoCs, and moves some of the generic peripherals under it. System control
module nodes are moved under this new interconnect also, and the SCM
clock layout is changed to use the new SCM node as the clock provider.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Control module driver needs to support syscon for register accesses, as
the DT hierarchy for control module driver is going to be changed. All
the control module related features will be moved under control module
node, including clocks, pinctrl, and generic configuration register
access. Temporary iomap is still provided very early in the boot for
access while syscon is not yet ready.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is no need to read the register with every invocation of the function,
as the value is constant. Thus, cache the value in a static variable.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Some of the TI clock providers will be converted to use syscon, thus
low-level regmap support is needed for the clock drivers also. This
patch adds this support, which can be enabled for individual drivers
in later patches.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The compatible DT node is now passed with the prm init, so there is no
need to do node matching here again. Added a new flag to the init data
also, to detect default IRQ support for OMAP4. Also, any booting omap4
DT setup always has a PRM node, so there is no need to check against
the special case where it would be missing.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Currently some cpu_is_X checks are used to setup prm_features, however
the same can be accomplished by just passing these flags from the PRM
init data. This is done in preparation to make PRM a separate driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This gets rid of need for some exported driver APIs, and simplifies the
initialization of the CM driver. Done in preparation to make CM a
separate driver. The init data is now also passed to the SoC specific
implementations, allowing future expansion to add feature flags etc.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
PRM device instance offset is now provided through the prm_init_data.
This gets rid of some cpu_is_X / soc_is_X calls from PRM core code,
preparing for PRM to be its own separate driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This gets rid of need for some exported driver APIs, and simplifies the
initialization of the PRM driver. Done in preparation to make PRM a
separate driver. The init data is now also passed to the SoC specific
implementations, allowing future expansion to add feature flags etc.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
ARM errata 798181 is applicable for OMAP5/DRA7 based devices. So enable
the same in the build.
DRA7xx is based on Cortex-A15 r2p2 revision.
ARM Errata extract and workaround information is as below.
On Cortex-A15 (r0p0..r3p2) the TLBI*IS/DSB operations are not
adequately shooting down all use of the old entries. The
ARM_ERRATA_798181 option enables the Linux kernel workaround
for this erratum which sends an IPI to the CPUs that are running
the same ASID as the one being invalidated.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no need to provide the control module base address through a
low-level API from the low-level IO init, as this information is
available through DT. This patch adds a new API to initialize the
control module though, but mostly makes the old API obsolete. The
old API can be completely removed once OMAP3 is made DT only.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is no need to provide the PRM base address through a low-level API
from the low-level IO init, as this information is available through DT.
Re-routed the parsing function to be called from the PRM drivers also to
simplify the implementation under io.c.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is no need to provide the CM base address through a low-level API
from the low-level IO init, as this information is available through DT.
Re-routed the parsing function to be called from the CM drivers also to
simplify the implementation under io.c.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Splits the clock related provider module inits under their own driver files.
Previously this was done for all modules under the common PRM driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Splits the clock provider init out of the PRM driver and moves it to
clock driver. This is needed so that once the PRCM drivers are separated,
they can logically just access the clock driver not needing to go through
common PRM code. This would be wrong in the case of control module for
example.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
BeagleBoard-X15 has capability for a fan and has an onboard TMP102
temperature sensor as well. This allows us to create a new thermal
zone (called, un-imaginatively "board"), and allows us to use some
active cooling as temperatures start edge upward in the system by
creating a new alert temperature (emperically 50C) for cpu.
NOTE: Fan is NOT mounted by default on the platform, in such a case,
all we end up doing is switch on a regulator and leak very minimal
current.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add bandgap and related thermal nodes. The patch adds 5 thermal
sensors. Only one cooling device for mpu as of now. The sensors are
the exact same on both dra72 and dra7. Introduce CPU, GPU, core nodes
for the moment as they are direct reuse of OMAP5 entities.
NOTE: OMAP4 has a finer counter granularity, which allows for a delay
of 1000ms in the thermal zone polling intervals. DRA7 have different
counter mechanism, which allows at maximum a 500ms timer. Adjust the
cpu thermal zone accordingly for DRA7.
Signed-off-by: Keerthy <j-keerthy@ti.com>
[t-kristo@ti.com: few reuse from OMAP5 entities]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added a new compatible string "ti,am437x-ocp2scp" for OCP2SCP module.
This is needed since except for the OCP2SCP used in AM437x, SYNC2 value
in OCP2SCP TIMING should be changed whereas the default value is sufficient
in AM437x.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NULL pointer check for superset->muxnames will always evaluate
true since muxnames is an array within struct omap_mux. Remove the
superfluous check to avoid warnings when using LLVM/clang.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All clock provider related drivers will now register their iomaps
with a static index. This makes it easier to split up the individual
drivers to their own files in subsequent patches.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP4 has different ordering of PRM and CM init calls in the early init.
Re-oder these accordingly for OMAP4 also. This is needed so that we
can do some optimizations in the following patches for the PRCM init.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is no need to call this separately from io.c, rather this can be
done commonly under the CM driver. Also, this patch makes the API static,
as it is no longer used outside the driver file.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is no need to call this separately from io.c, rather this can be
done commonly under the PRM driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2/3 now use generic API for the prm_clear_mod_irqs, the SoC specific
implementation details are provided through prm_ll_data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This makes the API the same as used with OMAP2, and makes it possible
to implement a generic driver API for the functionality.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The Kconfig-Option OMAP4_ERRATA_I688 is never visible due to a
contradiction in it's dependencies.
The option requires ARCH_MULTIPLATFORM to be 'disabled'. However, an
enclosing menu requires either ARCH_MULTI_V6 or ARCH_MULTI_V7 to be
enabled. These options inherit a dependency from an enclosing menu,
that requires ARCH_MULTIPLATFORM to be 'enabled'.
This is a contradiction and made this option also unavailable for
non-multiplatform configurations.
Since there are no selects on OMAP4_ERRATA_I688, which would ignore
dependencies, the code related to that option is dead and can be
removed.
This (logical) defect has been found with the undertaker tool.
(https://undertaker.cs.fau.de)
Signed-off-by: Stefan Hengelein <stefan.hengelein@fau.de>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Building an OMAP1510-only Kconfig generates the following warnings:
arch/arm/mach-omap1/pm.c: In function ¡omap1_pm_idle¢:
arch/arm/mach-omap1/pm.c:123:2: warning: #warning Enable 32kHz OS timer in order to allow sleep states in idle [-Wcpp]
#warning Enable 32kHz OS timer in order to allow sleep states in idle
^
arch/arm/mach-omap1/pm.c: At top level:
arch/arm/mach-omap1/pm.c:76:23: warning: ¡enable_dyn_sleep¢ defined but not used [-Wunused-variable]
static unsigned short enable_dyn_sleep = 0;
^
These are not so easy to fix in an obviously correct fashion, since I
don't have these devices up and running in my testbed. So, use
arch/arm/plat-omap/Kconfig and the existing pm.c source as a guide,
and posit that deep power saving states are only supported on OMAP16xx
chips with kernels built with both CONFIG_OMAP_DM_TIMER=y and
CONFIG_OMAP_32K_TIMER=y.
While here, clean up a few printk()s and unnecessary #ifdefs.
This second version of the patch incorporates several suggestions from
Jon Hunter <jgchunter@gmail.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Jon Hunter <jgchunter@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Kconfig options for the asm9260 timer is wrong as it can be selected by
another platform with allyes config and thus leading to a compilation failure
as some non arch related code is pulled by the compilation.
Fix this by having the platform Kconfig to select the timer as it is done for
the others drivers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Conflicts:
drivers/clocksource/Kconfig
Fixes: http://bugs.elinux.org/issues/127
the bb.org community was seeing random reboots before this change.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In commit 87517d26d8 ("ARM: dts: dra7-evm: Add extcon nodes for USB")
we enabled Extcon USB gpio to tackle the USB ID pin and get
peripheral mode to work.
But the extcon-gpio-usb driver [1] didn't make it into v4.0
and this makes the USB driver defer probe indefinitely breaking
USB Host functionality.
As a temporary fix we remove the extcon handle from the
USB controller and add it back when the extcon driver
merges in v4.1.
[1] - https://lkml.org/lkml/2015/2/2/187
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
SATA operation depends on PIPE3 PHY and if we want
to boot from SATA drives, we have to have the PIPE3 PHY
driver built-in.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
