VSID 0 is bad address. Don't create slb entries on coproc fault for
bad address
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_pe_reset and eeh_reset_pe are two different functions in the same
file which do mostly the same thing. Not only is this confusing, but
potentially causes disrepancies in functionality, notably eeh_reset_pe
as it does not check return values for failure.
Refactor this into the following:
- eeh_pe_reset(): stays as is, performs a single operation, exported
- eeh_pe_reset_full(): new, full reset process that calls eeh_pe_reset()
- eeh_reset_pe(): removed and replaced by eeh_pe_reset_full()
- eeh_reset_pe_once(): removed
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PHB, PE (and by association MVE) numbers are printed as a mix of decimal
and hexadecimal throughout the kernel. This can be misleading, so make
them all hexadecimal.
Standardising on hex instead of dec because:
- PHB numbers are presented in hex in sysfs/debugfs (and lspci, etc)
- PE numbers are presented as hex in sysfs and parsed in hex in debugfs
The only place I think this could cause confusing are the messages during
boot, i.e.
pci 000a:01 : [PE# 000] Secondary bus 1 associated with PE#0
which can be a quick way to check PE numbers. pe_level_printk() will
only print two characters instead of three, so the above would be
pci 000a:01 : [PE# 00] Secondary bus 1 associated with PE#0
which gives a hint it's in hex.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Whenever a PE is initialised in powernv, opal_pci_eeh_freeze_clear() is
called. This is to remove any existing freeze, and has no negative side
effects if the PE is already in an unfrozen state. On PHB backends that
don't support this operation and return OPAL_UNSUPPORTED, this creates a
scary and misleading warning message.
Skip the warning message on init if OPAL_UNSUPPORTED is returned.
As far as I'm aware, this currently only affects NPUs.
Fixes: 313483d ("powerpc/powernv: Unfreeze PE on allocation")
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ibm_pa_features array consists of structures that describe which bit
and byte in the ibm,pa-features property toggles one or more flags in
either the CPU, MMU, or user visible feature flags.
Each one consists of 7 values, which are all unsigned long, int or char,
meaning the compiler gives us no warning if we assign the wrong values
to the wrong elements. In fact we have had a bug here in the past, where
we were setting incorrect bits, see commit 6997e57d69 ("powerpc:
scan_features() updates incorrect bits for REAL_LE").
So switch to using named initialisers for the structure elements, to
reduce the likelihood of future bugs, and hopefully improve readability
also.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
These are the PPC optimised versions of various crypto algorithms, so we
should turn them on by default to get test coverage.
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The IBMEBUS code supports the GX bus found on Power7 and earlier CPUs.
On Power8 it has been replaced, and so we have no need for it.
We don't actually have a config symbol for Power8 vs Power7 etc., but
we only support booting little endian on Power8 or later, so use that as
a reasonable approximation.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When ending an oops, don't clear die_owner unless the nest count
went to zero. This prevents a second nested oops from hanging forever
on the die_lock.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When exiting xmon with 'x' (exit and recover), oops_begin bails
out immediately, but die then calls __die() and oops_end(), which
cause a lot of bad things to happen.
If the debugger was attached then went to graceful recovery, exit
from die() immediately.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add an option to use thin archives to build the kernel.
Thin archives are explained in commit a5967db9af ("kbuild: allow
architectures to use thin archives instead of ld -r").
This is a gradual way to introduce the option to testers.
Some change to the way we invoke ar is required so it can be used
by scripts/link-vmlinux.sh.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Make it an explicit option not dependant on COMPILE_TEST]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Under some configs we need to explicitly include cpu_has_feature.h,
otherwise we fail with:
arch/powerpc/lib/sstep.c:1992:7: error: implicit declaration of function 'cpu_has_feature'
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pasrsing of data written to the dlpar file in sysfs does not correctly
account for the possibility of reading past the end of the buffer. The code
assumes that all pieces of the command witten to the sysfs file are present
in the form "<resource> <action> <id_type> <id>".
Correct this by updating the buffer parsing code to make a local copy and
use the strsep() and sysfs_streq() routines to parse the buffer. This patch
also separates the parsing code into subroutines for each piece of the
command.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the unused but set variable srr1 in save_mce_event() to
fix the following GCC warning when building with 'W=1':
arch/powerpc/kernel/mce.c:75:11: warning: variable 'srr1' set but not used
It has never been used.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix two [-Wold-style-declaration] GCC warnings by moving the inline
keyword before the return type.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
MIN_HUGEPTE_SHIFT hasn't been used since commit d1837cba5d
("powerpc/mm: Cleanup initialization of hugepages on powerpc")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Version 3.00 of the ISA states that the PATS (partition table size) field
of the PTCR (partition table control register) and the PRTS (process table
size) field of the partition table entry must both be less than or equal
to 24. However the actual size of the partition and process tables is equal
to 2 to the power of 12 plus the PATS and PRTS fields, respectively. This
means that the max allowable size of each of these tables is 2^36 or 64GB
for both.
Thus when checking the size shift for each we should be checking for values
of greater than 36 instead of the current check for shifts larger than 24
and 23.
Fixes: 2bfd65e45e
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Useful to be able to dump the kernel hash page table to check
which pages are hashed along with their sizes and other details.
Add a debugfs file to check the hash page table. If radix is enabled
(and so there is no hash page table) then this file doesn't exist. To
use this the PPC_PTDUMP config option must be selected.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
[mpe: Fix build with SPARSEMEM_VMEMMAP=n & PSERIES=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Useful to be able to dump the kernels page tables to check permissions
and memory types - derived from arm64's implementation.
Add a debugfs file to check the page tables. To use this the PPC_PTDUMP
config option must be selected.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently there's some CMO (Cooperative Memory Overcommit) code, in
plpar_wrappers.h. Some of it is #ifdef CONFIG_PSERIES and some of it
isn't. The end result being if a file includes plpar_wrappers.h it won't
build with CONFIG_PSERIES=n.
Fix it by moving the CMO code into platforms/pseries. The two hcall
wrappers can just be moved into their only caller, cmm.c, and the
accessors can go in pseries.h.
Note we need the accessors because cmm.c can be built as a module, so
there needs to be a split between the built-in code vs the module, and
that's achieved by using those accessors.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts storcenter_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts pseries_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts ppc6xx_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts ppc64e_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts ppc64_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts pmac32_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
This patch disables deprecated IDE subsystem in pasemi_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts maple_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts g5_defconfig to use libata PATA drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts chrp32_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts cell_defconfig to use libata PATA drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts amigaone_defconfig to use libata PATA
drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Add comment clarifying that vio_find_node() takes a reference to the
embedded struct device which needs to be dropped after use.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure to drop any reference taken by bus_find_device() when creating
devices during init and driver registration.
Fixes: 55347cc996 ("[POWERPC] ibmebus: Add device creation and bus probing based on of_device")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure to drop any reference taken by bus_find_device() in the sysfs
callbacks that are used to create and destroy devices based on
device-tree entries.
Fixes: 6bccf755ff ("[POWERPC] ibmebus: dynamic addition/removal of adapters, some code cleanup")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This condenses the opal node searching into a single function that finds
all compatible nodes, instead of just searching the ibm,opal children,
for ipmi, flash, and prd similar to how opal-i2c nodes are found.
Signed-off-by: Jack Miller <jack@codezen.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Load monitored is no longer supported on POWER9 so let's remove the
code.
This reverts commit bd3ea317fd ("powerpc: Load Monitor Register
Support").
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No one uses reiserfs much these days, or is likely to in future. So drop
it from pseries and powernv defconfigs to save time and space. It's
still enabled in ppc64_defconfig so we get some build coverage.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In ISA v2.05, the tlbiel instruction takes two arguments, RB and L:
tlbiel RB,L
+---------+---------+----+---------+---------+---------+----+
| 31 | / | L | / | RB | 274 | / |
| 31 - 26 | 25 - 22 | 21 | 20 - 16 | 15 - 11 | 10 - 1 | 0 |
+---------+---------+----+---------+---------+---------+----+
In ISA v2.06 tlbiel takes only one argument, RB:
tlbiel RB
+---------+---------+---------+---------+---------+----+
| 31 | / | / | RB | 274 | / |
| 31 - 26 | 25 - 21 | 20 - 16 | 15 - 11 | 10 - 1 | 0 |
+---------+---------+---------+---------+---------+----+
And in ISA v3.00 tlbiel takes five arguments:
tlbiel RB,RS,RIC,PRS,R
+---------+---------+----+---------+----+----+---------+---------+----+
| 31 | RS | / | RIC |PRS | R | RB | 274 | / |
| 31 - 26 | 25 - 21 | 20 | 19 - 18 | 17 | 16 | 15 - 11 | 10 - 1 | 0 |
+---------+---------+----+---------+----+----+---------+---------+----+
However the assembler also accepts "tlbiel RB", and generates
"tlbiel RB,r0,0,0,0".
As you can see above the L field from the v2.05 encoding overlaps with the
reserved field of the v2.06 encoding, and the low bit of the RS field of the
v3.00 encoding.
Currently in __tlbiel() we generate two tlbiel instructions manually using hex
constants. In the first case, for MMU_PAGE_4K, we generate "tlbiel RB,0", which
is safe in all cases, because the L bit is zero.
However in the default case we generate "tlbiel RB,1", therefore setting bit 21
to 1.
This is not an actual bug on v2.06 processors, because the CPU ignores the value
of the reserved field. However software is supposed to encode the reserved
fields as zero to enable forward compatibility.
On v3.00 processors setting bit 21 to 1 and no other bits of RS, means we are
using r1 for the value of RS.
Although it's not obvious, the code sets the IS field (bits 10-11) to 0 (by
omission), and L=1, in the va value, which is passed as RB. We also pass R=0 in
the instruction.
The combination of IS=0, L=1 and R=0 means the value of RS is not used, so even
on ISA v3.00 there is no actual bug.
We should still fix it, as setting a reserved bit on v2.06 is naughty, and we
are only avoiding a bug on v3.00 by accident rather than design. Use
ASM_FTR_IFSET() to generate the single argument form on ISA v2.06 and later, and
the two argument form on pre v2.06.
Although there may be very old toolchains which don't understand tlbiel, we have
other code in the tree which has been using tlbiel for over five years, and no
one has reported any build failures, so just let the assembler generate the
instructions.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Rewrite change log, use IFSET instead of IFCLR]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we're not compiling for a specific CPU, ie. none of the
CONFIG_POWERx_CPU options are set, and CONFIG_GENERIC_CPU *is* set, we
currently don't pass any -mcpu option to the compiler. This means the
compiler builds for a "generic" Power CPU.
But back in 2014 we dropped support for pre power4 CPUs in commit
468a33028e ("powerpc: Drop support for pre-POWER4 cpus").
Given that, there's no point in building the kernel to run on pre power4
cpus. So update the flags we pass to the compiler when
CONFIG_GENERIC_CPU is set, to specify -mcpu=power4.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a config option that can help exercise the case when
the kernel is not running at PAGE_OFFSET.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An hcall was recently added that does exactly what we need during kexec
- it clears the entire MMU hash table, ignoring any VRMA mappings.
Try it and fall back to the old method if we get a failure.
On a POWER8 box with 5TB of memory, this reduces the time it takes to
kexec a new kernel from from 4 minutes to 1 minute.
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
[mpe: Split into separate functions and tweak function naming]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This halves the exception table size on 64-bit builds, and it allows
build-time sorting of exception tables to work on relocated kernels.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Minor asm fixups and bits to keep the selftests working]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This macro is taken from s390, and allows more flexibility in
changing exception table format.
mpe: Put it in ppc_asm.h and only define one version using
stringinfy_in_c(). Add some empty definitions and headers to keep the
selftests happy.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We haven't seen these before, but the soon to be merged relative
exception tables support causes them to be generated.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
